Thank you for purchasing this Vollrath equipment. Before operating the
equipment, read and familiarize yourself with the following operating
and safety instructions. SAVE THESE INSTRUCTIONS FOR FUTURE
REFERENCE. Save the original box and packaging. Use this packaging
to ship the equipment if repairs are needed.
SAFETY PRECAUTIONS
To ensure safe operation, read the following statements and understand
their meaning. This manual contains safety precautions which are
explained below. Please read carefully.
WARNING
Warning is used to indicate the presence of a hazard that will or can
cause severe personal injury or death.
CAUTION
Caution is used to indicate the presence of a hazard that will or can
cause minor or major personal injury if the caution is ignored.
Operator’s Manual
Models JW1 and JW2
CM2-12020
NOTICE: Notice is used to note information that is important but not
hazard-related.
To reduce risk of injury or damage to the equipment
• Plug only into grounded electrical outlets matching the voltage on
the rating plate.
• Use this equipment in a flat, level position.
• Unplug equipment and let it cool before cleaning or moving.
Equipment remains hot after it is turned off.
• Unplug when not in use.
• Keep equipment and power cord away from open flames, electric
burners or excessive heat.
• Do not operate unattended.
• Closely supervise equipment operating in public areas and/or
around children.
• Do not operate if equipment has been damaged or is malfunctioning.
FUNCTION AND PURPOSE
This equipment is intended to melt cheese or warm plates in medium
volume food service operations and restaurants. It is not intended to
bake food or cook raw food. It is intended for use in commercial
foodservice operations only. It is not intended for household, industrial
or laboratory use.
CM2-12026
Item No.ModelDescription
CM2-12020
CM2-12026
JW1
Cheese Melter, 20" wide, 120V
JW2
Cheese Melter, 26" wide, 120V
CLEARANCE AND ENVIRONMENT REQUIREMENTS
Do not place oven on surfaces or near walls, partitions or kitchen
furniture unless they are made of non-combustible material or clad with
non-combustible heat-insulating material. Ovens must not be used near
or below curtains and other combustible materials.
Do not place the oven adjacent to a heat producing appliance.
Allow a minimum of 8 inches (20.3 cm) of clearance on the left and
right sides of the oven.
Register your product at Vollrath.com/registration and become eligible to win a free 10" Vollrath Tribute® fry pan.
2017 The Vollrath Company L.L.C.Part No. 351018-1 en12/8/17
SET UP
Install the legs
NOTICE: Legs must be installed. Failure to install the legs will
restrict airflow and cause the oven to overheat.
Screw the legs onto the threaded nuts below the cheese melter.
Install the Shelf
Slide the shelf into the oven.
FEATURES
A
B
C
D
BEFORE FIRST USE
Clean the oven. See “Cleaning” on page 3.
OPERATION
CAUTION
Burn Hazard
Do not touch the equipment while it is heating or operating.
Hot surfaces can burn skin.
Preheat
1. Plug the oven into a grounded electrical outlet that matches the
rating on the name plate found on the oven.
NOTICE: Using a voltage other than the nameplate rated voltage
will cause damage to the unit. Incorrect voltage,
modification to the power cord or electrical components
can damage unit and will void the warranty.
2. Adjust the shelf to the desired position.
3. Press the On/Off switch to the ON position. One heater element will
turn on and the oven will be in standby mode.
4. Set the timer for 10 minutes. The second element will turn on and
the oven will be full power.
Melt Cheese, Finish Cooked Food
1. Place the food on or in an oven-proof pan and place the pan on the
shelf.
2. Set the timer to the appropriate length of time to melt cheese, brown
or finish cooked food items.
3. When the time on the timer has expired, the oven will enter a
standby mode.
4. When finished using the oven, press the On/Off switch to the OFF
position.
Front View
E
I
Back View
A Fan
B Timer
C Adjustable Shelf
D On/Off Switch
E Reset Button
220 and 26 Inch Cheese Melters Operator’s Manual – Models JW1, JW2
CLEANING
1. Press the On/Off switch to the OFF position.
2. Unplug the oven.
WARNING
Electrical Shock Hazard
Do not spray water or cleaning products. Liquid could contact
the electrical components and cause a short circuit or an
electrical shock.
3. Let the oven cool completely.
4. Slightly dampen a soft cloth with a warm water.
5. Use the dampened cloth to clean the interior and exterior of the
oven, and the air intake on the side of the oven
6. Remove the shelf and clean with warm soapy water.
CAUTION
Burn Hazard
Allow equipment to cool before moving or cleaning.
NOTICE: Do not use abrasive materials, scratching cleansers or
TROUBLESHOOTING
ProblemMight be Caused ByCourse of Action
Oven does not heat.Oven is not plugged in.Plug in the oven.
scouring pads to clean the equipment. These can damage
the finish.
The timer has not been set.Set the timer. The timer must be set to turn on all the heater tubes.
The wall breaker may be tripped.Reset the breaker.
The reset may be tripped.Look at the side of the oven to see if an object is preventing the fan
blades from turning.
1. Press the On/Off switch to the OFF (O) position.
2. Unplug the oven.
3. Wait 30 minutes for the oven cool.
4. Remove the object.
5. Plug in the oven.
6. Press the On/Off switch to the ON (|) position.
7. Press the reset button.
8. If the problem persists call Vollrath Technical Services.
Inspect the fan blades to see if they are dirty.
1. Press the On/Off switch to the OFF (O) position.
2. Unplug the oven.
3. Wait 30 minutes for the oven cool.
4. Clean the fan blades.
5. Plug in the oven.
6. Press the On/Off switch to the ON (|) position.
7. Press the reset button.
8. If the problem persists call Vollrath Technical Services.
One or more heater tubes may have
burned out.
There may be a problem with the heat
switch.
Oven repeatedly overheats.The fan may be dirty.Verify the fan blades are clean.
There may be a problem with the fan.Run the oven for 10 minutes. If the fan does not run, contact
20 and 26 Inch Cheese Melters Operator’s Manual – Models JW1, JW23
Contact Vollrath Technical Services.
Vollrath Technical Services.
TROUBLESHOOTING (CONTINUED)
ProblemMight be Caused ByCourse of Action
The fan is not running.There may be a problem with the fan or
The oven is turned off and the fan is
running.
fan switch.
Normal operation. The fan turns on as
needed to cool the oven.
Run the oven for 10 minutes. If the fan does not run, contact
Vollrath Technical Services.
_
SERVICE AND REPAIR
When under warranty, repair is available for this product via carry-in service. To begin the process:
1. Contact Vollrath Technical Services at 1-800-309-2250. Please be ready with the item number, model number and serial number. You can find this
information on the nameplate located on the side or back of the equipment. Also please provide a proof of purchase indicating the date the
equipment was purchased.
2. A technical services representative will help you troubleshoot the problem over the phone.
3. If the representative determines the issue require professional service, he or she will help you locate an authorized service center.
4. Contact the authorized service center and transport the equipment to the authorized service center. Vollrath will cover the cost to repair and/or
replace defective parts within the equipment warranty period. The cost of transporting the equipment to and from the service center is not
covered by the warranty.
WARRANTY STATEMENT FOR THE VOLLRATH CO. L.L.C.
The Vollrath Company LLC warrants the products it manufactures or distributes against defects in materials and workmanship as specifically
described in our full warranty statement. In all cases, the warranty runs from the date of the end user’s original purchase date found on the receipt.
Any damages from improper use, abuse, modification or damage resulting from improper packaging during return shipment for warranty repair will
not be covered under warranty.
The warranty does not apply to products purchased for personal, family or household use, and The Vollrath Company LLC does not offer a written
warranty to purchasers for such uses.
Heater Tubes: The warranty period is 1 year, including labor when performed at an authorized service center. Heater tube glass damage is not
covered by this warranty. Customer is responsible for the cost of transporting the product to the authorized service center.
Warrantied Parts: The warranty period is 2 years parts, 1 year labor.
For complete warranty information, product registration and new product announcement, visit www.vollrath.com.
www.vollrath.com
The Vollrath Company, L.L.C.
1236 North 18th Street
Sheboygan, WI 53081-3201 U.S.A.
Main Tel: 800.624.2051 or 920.457.4851
Main Fax: 800.752.5620 or 920.459.6573
Customer Service: 800.628.0830
Canada Customer Service: 800.695.8560