Vizio WB-31 User Manual
INSTALLATION MANUAL
FLAT LCD DISPLAY MOUNT MODEL
WB-31
Swingout Arm Mount
WB-31
Page 2 Installation Instructions
TABLE OF CONTENTS
Parts List 4
Installation Tools 4
5duts dooW - noitallatsnI etalpkcaB
6ecafruS etercnoC - noitallatsnI etalpkcaB
7noitallatsnI 13-MW
8rotinoM eht gnillatsnI
9mrA tuogniwS eht gnitsujdA
01noitallatsnI etalP retpadA
11snoitacificepS lacinhceT
WB-31
Installation Instructions Page 3
Warning Statements
WARNING: THE WALL STRUCTURE MUST BE CAPABLE OF SUPPORTING AT LEAST A
MAXIMUM WEIGHT OF 50 LBS. IF NOT, THE WALL MUST BE REINFORCED.
PROPER INSTALLATION PROCEDURE BY A QUALIFIED SERVICE TECHNICIAN, AS
OUTLINED IN THE INSTALLATION INSTRUCTIONS, MUST BE ADHERED TO.
FAILURE TO DO SO COULD RESULT IN SERIOUS PERSONAL INJURY, OR EVEN
DEATH.
W
ARNING: SAFETY MEASURES MUST BE PRACTICED AT ALL TIMES DURING THE
INSTALLATION OF THIS PRODUCT. USE PROPER SAFETY GEAR AND TOOLS FOR
THE INSTALLATION PROCEDURE TO PREVENT PERSONAL INJURY.
W
ARNING
: PRIOR TO THE INSTALLATION OF THIS PRODUCT, THE INSTALLATION
INSTRUCTIONS SHOULD BE READ AND COMPLETELY UNDERSTOOD. THE
INSTALLATION INSTRUCTIONS MUST BE READ TO PREVENT PERSONAL INJURY
AND PROPERTY DAMAGE. KEEP THESE INSTALLATION INSTRUCTIONS IN AN
EASILY ACCESSIBLE LOCATION FOR FUTURE REFERENCE.
Indicates that the power plug is to be disconnected from the power outlet.
Safety precautions must be taken at all times.
Warning and Caution statements.
A secure structure must support the weight, or load, of the display. When mounting to a wall that contains
wooden studs, dead center of the wooden stud must be confirmed prior to installation.
Do not install on a structure that is prone to vibration, movement or chance of impact. Failure to do so could result
in damage to the display and/or damage to the mounting surface.
Do not install near heater, fireplace, direct sunlight, air conditioning or any other source of direct heat energy. Failure
to do so may result in damage to the display and could increase the risk of fire.
At least two qualified people should perform the installation procedure. Injury and/or damage can result from dropping or mishandling the display.
Recommended mounting surfaces: wooden studs and solid-flat concrete. If the mount is to be installed on any surface other than wooden studs, use suitable hardware (which is commercially available).
Contact Orion Images with any technical/ installation questions.
WB-31
Page 4 Installation Instructions
Parts List
NOTE: This mount is shipped with all intallation hardware and components. Make sure that none
of these parts are missing and/ or damaged before beginning installation. If there are parts
missing and/or damaged, please stop and contact
TOA Electronics, Inc.
200x200 ADAPTER HARDWARE
Swingout Arm (Qty 1)
1/4” Wedge Anchors
(Qty 4). These are used only
for concrete installations.
Mounting Backplate (Qty 1)
M6 x 35mm Set Screw
(Qty 1)
M4 x 10mm Phillips Head
Scews (Qty 4)
#14 x 2” Wood Screw
(Qty 4)
M6 x 30mm Phillips Pan
Head Screws (Qty 4)
M6 x 20mm Phillips Pan
Head Screws (Qty 4)
M6 x 12mm Phillips Pan Head
Screws (Qty 4)
M5 x 16mm Phillips Pan
Head Screws (Qty 4)
M5 x 12mm Phillips Pan
Head Screws (Qty 4)
M4 x 20mm Phillips Pan
Head Screws (Qty 4)
M5 Flat
Washer (Qty 4)
M4 Flat
Washer (Qty 4)
M4 x 16mm SEMS
Phillips Pan Head
Screw (Qty 4)
100x200 ADAPTER HARDWARE
200x200 Adapter Plate
(Qty 1)
100x200 Adapter Plate
(Qty 1)
M4 x 5mm Phillips Pan Head
Screws (Qty 4)
M4 x 6mm Phillips Pan Head
Screws (Qty 4)
M4 x 10mm Phillips Flat
Head Screws (Qty 6)
Installation Tools
Phillips Head Screw Driver Soft Material/ Blanket 1/2" Socket and Wrench Pencil
Tape Measure Drill Gun Level (Supplied)
14mm Socket (Supplied) Ratchet with 9/16” Drive Socket
M3 Allen Wrench (Supplied) Stud Finder (Commercially Available)
Loading...