Vision Fitness R2050, R2150 User Manual

Quantity: 8

M6 Arc Washer

Quantity: 4

M8 x 25L Bolt

Quantity: 8

M6 x 35L Bolt

Warranty Card

Owners Manual Assembly Guide

Color Coded Hardware Bags

Seat Rail Stopper

Water Bottle and Cage

Power Supply

Pedals

5mm L-Shaped Wrench

Console Mast Cover

PARTS BOX

Quantity: 6

SW8 Lock Washer

Quantity: 2

M8 x 20L Bolt

Quantity: 4

M8 x 15L Bolt

Quantity:1

M8 x 10L Set Screw

PINK BAG

Quantity: 6

SW8 Lock Washer

Quantity: 4

SW8 Lock Washer

Quantity: 2

M4x10 Screw

HARDWARE INCLUDED

Quantity: 2

M8 x 65L Bolt

Quantity: 4

M8 x 15L Bolt

BLUE BAG

Quantity: 2

M8 x 20L Bolt

ORANGE BAG

4mm L-Shaped Wrench

17mm/15mm Pedal Wrench

5mm T-Shaped Wrench

Screwdriver

TOOLS & PARTS INCLUDED

it all starts

with a

vision

500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551

toll free 800.335.4348 • phone 920.648.4090 • fax 920.648.3373

www.visionfitness.com

Assembly

Guide

R2050 AND R2150

STEP-THRU SEMI-RECUMBENT FITNESS BIKES

NOTE:

PINK BAG

• Slide the console mast cover onto

the console mast.

• Take the wire tie that exits the

bottom of the console mast and wrap

it around the wire harness and heart

STEP

rate wires that are sitting in the

console mast bracket on the frame.

Pull the wire tie up through the top of

the console mast so that the wire

harness and heart rate wires exit the

top of the mast.

• Slide the bottom of the console mast

over the frame bracket being careful

not to pinch the heart rate wires or

wire harness. Assure the mast is

positioned correctly by inserting the

Set Screw (M8x10L) through the front

edge of the mast. Tighten with the

5mm T-handle wrench. Secure the

mast to the frame with four bolts

(M8x15L) and four lock washers (SW8).

Tighten with the 5mm T-handle wrench.

• Slide the console mast cover down

so it sits on the frame covers.

• Mount the console mast handlebar

to the console mast with two bolts

(M8x20L) and two lock washers (SW8).

Tighten with the 5mm T-handle wrench.

• With the screwdriver remove the

four bolts on the back side of the

console. Plug in the wire harness and

heart rate wires to the back side of the

console. Mount the console to the

console mast with the four bolts and

screwdriver.

• Remove the water bottle cage bolts

PEDALS

from the backside of the console mast.

Mount the water bottle cage to the

mast with these two bolts and the

screwdriver.

STEP

• Attach the left and right pedals to

the left and right crank arms.

both pedals and crank arms should

be labeled left or right. Tighten with

the included pedal wrench.

• Plug in the power supply to the power

socket on the front side of the bike.

Console Mast

Cage

Water Bottle

STEP

Cover

Console Mast

Bracket

Console Mast

R2050 AND R2150

Guide

Assembly

STEP-THRU SEMI-RECUMBENT FITNESS BIKES

your Fitness Bike to prevent loosening and noise. Also, during each assembly step, ensure that ALL bolts

To avoid possible damage to this Fitness Bike, please follow these assembly steps in the correct order.

Before proceeding, find your new Fitness Bike’s serial number located on the front axle tube, and enter

here:

Refer to this number when calling for service, and enter this serial number on your Warranty Card and in

your own records. Be sure to read your Owner’s Guide before using your new Fitness Bike.

and screws are in place and partially threaded in before completely tightening any ONE bolt or screw.

If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12

NOTE: It is recommended that you apply grease to the threads of each bolt and screw as you assemble

Rear Foot

Joint Cover

Rear Foot

ORANGE BAG

• Slide the Rear Foot into place on the

STEP

back end of the frame. Secure the foot

in place to the frame with two bolts

(M8x20L) and two lock washers (SW8)

to the outside holes and with two bolts

(M8x65L) and two lock washers (SW8)

to the inside holes. Tighten with the

5mm T-Handle Wrench.

• Attach each half of the rear foot joint

cover with the M4x10L screw. Tighten

with the screwdriver.

BLUE BAG

• Rotate the handle on the seat frame to

the forward most position. Tighten the

adjustment bolt on the seat frame

bracket with the 5mm T-Shaped wrench.

• Slide the seat frame onto the seat rail.

STEP

Attach the seat rail stopper onto the seat

rail with two (M8x25L) bolts and two

lock washers (SW8). Tighten with the

5mm T-handle wrench.

• Connect the heart rate wires in the

seat handlebar to the heart rate wires

coming up from the seat frame.

• Mount the seat handlebars to the seat

frame with four bolts (M8x15L) and four

lock washers (SW8). Tighten with the

5mm T-Handle wrench.

Stopper

Seat Rail

Seat Frame

Adjustment Bolt

• Mount the seat bottom cushion to the

seat frame with four bolts (M6x35L) and

four arc washers (M6). Tighten with the

4mm L-shaped wrench.

• Mount the seatback cushion to the

seat frame with four bolts (M6x35L) and

four arc washers (M6). Tighten with the

4mm L-shaped wrench.