Page 1
Assembly
Guide
E3600HRT
COMMERCIAL UPRIGHT FITNESS BIKE
Page 2
1
STEP
2
STEP
3
STEP
4
STEP
To avoid possible damage to this Fitness Bike, please follow these assembly steps in the correct order. Before proceeding, find your
new Fitness Bike’s serial number located on the front axle tube, and enter here:
Refer to this number when calling for service, and enter this serial number on your Warranty Card and in your own records. Be
sure to read your Owner’s Guide before using your new Fitness Cycle.
If any parts, hardware or tools are missing, please call 1.800.335.4348, Extension 12
NOTE: It is recommended that you apply grease to the threads of each screw as you assemble your Fitness Bike to prevent loosen-
ing and noise. Also, during each assembly step, ensure that ALL screws are in place and partially threaded in before completely
tightening any ONE screw.
Assembly
Guide
E3600HRT
COMMERCIAL UPRIGHT FITNESS BIKE
Page 3
5mm Allen Wrench
15mm Pedal Wrench
Screwdriver
TOOLS & PARTS INCLUDED
PARTS BOX
Console Mast Cover
Water Bottle & Cage
Color-coded Hardware Bags
Owner’s Guide
Assembly Guide
Warranty Card
Heart Rate Chest Strap
Page 4
ORANGE BAG
PINK BAG
HARDWARE INCLUDED
M8 x 65L Screw
Quantity: 2
BLUE BAG
M8 x 15L Screw
Quantity: 7
M8 x 20L Screw
Quantity: 2
M8 x 20L Screw
Quantity: 2
M8 Lock Washer
Quantity: 4
M8 Lock Washer
Quantity: 6
M8 Lock Washer
Quantity: 2
Page 5
5
1
STEP
Rear Foot
1
STEP
• Install the rear foot with four lock
washers (M8), two inside screws
(M8x65L), and two outside screws
(M8x20L). Tighten with the 5mm Allen
wrench.
ORANGE BAG
Page 6
6
2
STEP
Console Mast
Boot
Heart Rate
Wires
Wire Harness
Console Mast
Frame
Bracket
2
STEP
• Slide the console mast boot onto the
console mast.
• Unfold the wire harness located in
the console mast frame bracket.
Connect it to the wire tie coming from
the bottom of the console mast. Pull
the wire tie and wire harness up
through the top of the console mast
while simultaneously sliding the mast
into the frame bracket.
• Secure the mast to the frame using
six lock washers (M8) and six screws
(M8x15L). Tighten with the 5mm Allen
wrench. Place the seventh screw
(M8x15L) in the rear of the frame
bracket and tighten until snug.
• Slide the console mast boot down
and snap it into place on the side cover.
• Remove the nuts (M8) from the
bottom of the seat. Attach the seat to the
seat post with the nuts you just removed.
Tighten with the 15mm wrench.
BLUE BAG
Page 7
7
3
STEP
Handlebar
3
STEP
• Feed the heart rate wires of the
handlebar through the small hole
located in the front of the console
mast. Pull these wires up through the
hole at the top of the console mast.
Attach the handlebar to the console
mast using two lock washers (M8)
and two screws (M8x20L). Tighten
with the 5mm Allen wrench.
PINK BAG
Page 8
8
500 South CP Avenue • P.O. Box 280 • Lake Mills. WI 53551
toll free 1.800.335.4348 • phone 1.920.648.4090 • fax 1.920.648.3373
www.visionfitness.com
©2004 Vision Fitness. All Rights Reserved. 6.04 Part #Z36CB39-AG
AG18.21PRD
REV2
4
STEP
Console
Accessory
Tray
4
STEP
• Remove the four mounting screws
from the back of the console with the
screwdriver. Make sure the 9-Volt battery is plugged in and in place on the
back of the console. Plug-in the wire
harness and the two heart rate wires to
the back of the console. Attach the console to the console mast with the four
screws removed earlier in this step.
• With the screwdriver, remove the
two screws located half way up the
console mast. Attach the accessory
tray to the console mast with the two
screws. Insert the water bottle.
CONSOLE
Loading...