Viking K-1700-3, K-1700-3-EWP User Manual

Vandal Resistant Features: 14 gauge, louvered,
stainless steel faceplate with stainless steel speaker/mic screen, heavy duty metal keypad and “Call” button
Optional Enhanced
Weather Protection (EWP)
• Yellow “in use” LED
• Volume adjustments for microphone and speaker
• Advanced call progress detection: disconnects on
• Selectable auto-answer feature
• Selectable push button disconnect
• Zinc plated steel rough-in box with (2) 3/4” conduit knockouts
• Optional VE-6x7 Surface Mount Box available
• Selectable maximum call time
• Selectable momentary or continuous Touch Tone output
• Selectable VOX switching speed
?
?
K-1700-3 &
K-1700-3 &
K-1700-3-EWP
K-1700-3-EWP
Handsfree Phone
with Keypad
March 28, 2002
PPrraaccttiicce
e
T
T
EELLEECCOOM
M
S
S
OOLLUUTTIIOONNSSFFOORRTTHHE
E
221
1
SST
T
C
C
EENNTTUURRY
Y
TECHNICAL
TECHNICAL
Attractive, Vandal Resistant,
Handsfree, Speaker Phone
The K-1700-3 provides a tough and attractive handsfree phone for apartment, and residential door entry or applications requiring a vandal resistant speaker phone.
When the “Call” button is pressed, the K-1700-3 returns dial tone. The key­pad may then be used to dial any number. If no Touch Tone is entered with­in 8 seconds, CPC is detected, a busy signal is detected, or the programma­ble maximum call time has elapsed, the K- 1700-3 will automatically disconnect. Alternatively, the K-1700-3 may be discon-
FFeeaattuurrees
s
PPhhoonnee......771155..338866..8888661
1
Power: Telephone line powered 20V DC/20mA minimum (26mA minimum with DIP switch 7 ON) Dimensions: Overall: 140mm x 165mm x 66mm (5.5” x 6.5” x
2.6”) , Rough-in box: 114mm x 140mm x 64mm (4.5” x 5.5” x 2.5”)
Shipping Weight: 1.6 kg (3.5 lbs) Environmental: -26°C to 54°C (-15°F to 130°F) with 5% to 95%
non- condensing humidity
Speaker Volume: approximately 70 db maximum @1m Connections: Standard - (1) two-position terminal block, EWP -
Gel-filled tip and ring connectors
CPC Disconnect Time: 300ms minimum REN #: 0.5 A
SSppeecciiffiiccaattiioonns
s
nected by pressing the “Call” button again. The K-1700-3 comes com­plete with a standard, flush mount, rough-in box (left). In addition, an optional weather resistant, surface mount box is available (right).
For outdoor or harsh environments, the K-1700-3 is available with Enhanced Weather Protection (EWP). EWP products feature rubber gas­kets and boots, closed cell foam gasket­ing, hand soldered silicon sealed con­nections, anti-corrosive gel filled tip and
ring connectors, as well as urethane encapsulated circuit boards with internaly sealed, field­adjustable trim POTS and DIP switches.
hhttttpp::////wwwwww..vviikkiinnggeelleeccttrroonniiccss..ccoom
m
Need More Information on EWP?
Call (715) 386-4345 and select 859.
Need More Information on the VE-6x7?
Call (715) 386-4345 and select 424.
AApppplliiccaattiioonns
s
• Apartment entry phone when used with the K-1900-3
Apartment Entry Dialer or
C-3000 Apartment Entry Controller
• Residential gate or door entry phone when used with the
C-2000 Door Entry Controller
• Courtesy and customer assistance phone
• Automated teller (ATM) phone
• Security or emergency phone
• Hot-Line phone when used with the K-1900-5 Hot-Line
Dialer
• Kiosk phone with (100 number speed dialing) when used
with the K-1900-9 Multi-Number Dialer
?
?
?
?
Need More Information on the K-1900-3?
Call (715) 386-4345 and select 312.
Need More Information on the C-2000?
Call (715) 386-4345 and select 156.
Need More Information on the K-1900-5?
Call (715) 386-4345 and select 317.
Need More Information on the K-1900-9?
Call (715) 386-4345 and select 321.
?
Need More Information on the C-3000?
Call (715) 386-4345 and select 162.
IInnssttaallllaattiioon
n
Optional VE-6x7 Surface Mount Box (not included) is designed to be surface mounted to a single gang box, pedestal or directly to a wall.
* Clean surface and adhere label when used with the K-1900-3 Apartment Entry Dialer.
Rear View of the K-1700-3
K-1700-3 shown with American Access System’s Gooseneck Pedestal (not included). For more information, call (303) 799-9757
Caution: When multiple line powered products (such as the K­1900-5 AND the K-1700-3) are placed in series, higher talk bat-
tery may be required.
Optional K-1900-3
150 Unit Apartment Entry
Dialer (not included)
Optional C-2000 Advanced Door Entry Controller (not
included)
Optional C-3000
Apartment Entry System
(not included)
?
Need More Information on the C-3000?
Call (715) 386-4345 and select 162.
?
Need More Information on the K-1900-3?
Call (715) 386-4345 and select 312.
?
Need More Information on the C-2000?
Call (715) 386-4345 and select 156.
?
Need More Information on Talk Battery?
Call (715) 386-4345 and select 512.
?
Need More Information on the VE-6x7?
Call (715) 386-4345 and select 424.
C.O. Line or
Analog
PABX/KSU
Station
Gel-Filled Tip and
Ring Connectors
(included with
EWP only)
or
VIKING
POWER
13.8 VAC
123
4
PWR LED
C.O. INPHONES
1 2 3 4
©
ELECTRONICS
HUDSON, WI 54016
ADVANCED DOOR ENTRY CONTROLLER
C.O. LINE INPUT
HOUSE PHONES
DOOR STRIKE 1 DOOR STRIKE 2 DOOR STRIKE 3 DOOR STRIKE 4 AUX CONTACTS
ENTRY
ENTRY
PHONE 1
PHONE 2
MODEL C-2000
VIKING
ENTRY
ENTRY
PHONE 3
PHONE 4
CONTACT CLOSURE
-or-
LOGIC
AUX
INPUTS
Red (Ring)
Green (Tip)
VIKING
POWER
13.8 VAC
SWITCH
12 UNIT APARTMENT
ENTRY CONTROLLER MODULE
DOOR
POSTAL
STRIKE
LOCK
1
INPUT
DIP
3456712
1 2 3
ENTRY 1 ENTRY 2
6.5”
5.12”
DOOR STRIKE
2
©
VIKING
ELECTRONICS
HUDSON, WI 54016
8
MULTI-MODULE INTERCONNECT
OUT IN
MODEL C-3000
12 APARTMENT LINES IN/OUT
RJ21X
4.04”
APARTMENT ENTRY
VIKING©
MOD
POWER 13.8 VAC
PROGRAMMING
OFF ON
LINE IN PHONE
5.5”
SYSTEM
VIKING
ELECTRONICS
HUDSON, WI 54016
EL K-
RELAY CONTACTS
1A 1B
1 2 3 4 5 6 7 8 9 10
1900-3
AUX.
18 VDC
TRIG.
200mA
INPUT
- +
or
5.64”
Rough-In Box
4.5”
2.5”
Condensation
2.25”
(included)
5.5”
Drain Hole
6.72”
Front View of Optional
VE-6x7 (not included)
3.25”
or
3/4” Conduit Knockouts
Press "Call" button
ter tenant code
then en
(4) 0.38” diameter
(2) 0.2 x 0.43 slots
(1) .74”
diameter
Condensation
Drain Hole
Adhere gasket to front panel, centering over mounting holes
Yellow “In Use” indicator LED
*Optional Instruction Label
(4) 6-32 X 3/4” Stainless steel, flat head, hexdrive, screws (included)
3.0” 3.3”
3.0”
Rear View of Optional VE-6x7 (not included)
PPrrooggrraammmmiinng
g
A. Dip Switch Programming
With DIP switch 7 in the “OFF” position (default), the K-1700-3 will output a momentary Touch Tone (125ms) each time a key is pressed. To generate Touch Tones for as long as a key is pressed, put DIP switch 7 to the “ON” position.
Note: The unit requires higher loop current (26mA minimum) with DIP switch 7 “ON”.
B. Volume Adjustments
E. Momentary or Continuous Touch Tone Output
(DIP Switch 7)
C. Auto-Answer Feature (DIP Switch 5)
With DIP switch 5 in the “ON” position (default), the K-1700-3 will automatically answer the line during the first incom­ing ring. This feature is useful for monitoring entrances. In the “OFF” position, the K-1700-3 will not automatically answer incoming calls.
1. Microphone: Certain noisy locations (background traffic, machinery or wind) may cause one way talk path (only microphone
audio is heard). In this case, the microphone volume may need to be decreased as shown above.
2. Speaker: To increase, decrease or turn off the speaker (for monitoring purposes only), adjust the speaker volume control as
shown above.
Switch 1
OFF
ON
OFF
ON
Switch 2
OFF
OFF
ON
ON
Maximum Call Time
Disabled (default)
1 minute
3 minutes
9 minutes
Rear View
of the K-1700-3
Switch 3
OFF
ON
OFF
ON
Switch 4
OFF
OFF
ON
ON
Disconnect on Silence
Off
10 seconds
40 seconds (default)
90 seconds
D. Push Button Hang Up (DIP Switch 6)
With DIP switch 6 in the “ON” position (default), the “Call” button alternately connects and disconnects calls. In the “OFF” position, the “Call” button is only used to connect and the K-1700-3 must rely on call progress (busy, return to dial tone, silence time-out, or maximum call time) for an automatic disconnect.
Switch 5
OFF
ON
Auto Answer Feature
Automatic answer disabled
Automatic answer enabled (default)
Switch 6
OFF
ON
Push Button Feature
Connects calls only
Connects/disconnects calls (default)
Switch 7
OFF
ON
Touch Tone Output
Momentary Touch Tone, 125ms (default)
Continuous Touch Tone (while key is pressed)
Switch 8
OFF
ON
VOX Switching Speed
Fast, 0.2 seconds (default)
Slow, 0.7 seconds
With DIP switch 8 in the “OFF” position (default), the VOX switching speed (delay time between talk and listen mode) is set to fast (0.2 seconds). In the “ON” position, it is set to slow (0.7 seconds).
F. VOX (Talk/Listen) Switching Speed (DIP Switch 8)
The K-1700-3 will output 3 beeps and automatically hang-up after detecting any of the following: busy signal (standard or fast/reorder), CPC (short break in line current when called party hangs up), return to dial tone, maximum call time or silence time out.
G. Advanced Call Progress Detection
Microphone Volume
(see section B)
K-1700-3
K-1700-3-EWP
-or-
OffOff
ON
OFF
Off
ON
1 2 3 4
1 2 3 4 5 6 7 8
DIP Switches
(see section A)
Speaker Volume
(see section B)
K-1700-3 K-1700-3-EWP
-or-
Off
ON
OFF
ON
1 2 3 4
Due to the dynamic nature of the product design, the information contained in this document is subject to change without notice. Viking Electronics, and its affiliates and/or subsidiaries assume no responsibility for errors and omissions contained in this information. Revisions of this document or new editions of it may be issued to incorporate such changes.
Fax Back Doc 157
ZF310000 Rev D
Printed in the U.S.A.
The K-1900-3 converts any Touch Tone phone into a multi-number auto dialer that will store up to 150 telephone numbers in non-volatile E2memory. Use with Viking’s K-1700-3 or K-1900-8 phones to provide vandal resistant handsfree or handset communication.
When a call initiated by the K-1900-3 is answered by an apartment or business ten­ant, a built-in contact closure may be activated to control an electric gate or door strike. Up to 150 keyless entry codes may also be programmed, providing tenants with keyless entry. The K-1900-3 can be programmed locally or remotely using a standard Touch Tone phone. The K-1900-3 has built-in user dialing restriction to help prevent unauthorized calls and toll fraud.
C. K-1900-3 Apartment/Office Entry Dialer
AApppplliiccaattiioonns
s
The C-2000 allows up to 4 entry phones to call into your existing residential or busi­ness phones or phone system. Tenants may answer the call, converse with the visi­tor and activate a contact closure to control electronic gates or door strikes.
The C-2000 provides “Caller ID,” “Call Waiting ID” and “Call Waiting” tone when the phone line is in use. Tenants may gain entry at each gate by entering a Touch Tone keyless entry code.
Tenants may call out to each entry phone for monitoring purposes. An auxiliary input is also available for connecting a common garage door opener/receiver and auxiliary keyless entry keypads.
A. C-2000 Advanced Door Entry Controller
This entry system is designed to utilize a building’s existing telephone wiring and to address a variety of apartment entry applications. Viking’s C-3000 Entry System provides secure multi-tenant building access, without the need for any C.O. lines; the only requirement is that each tenant have a touch-tone telephone set wired to their apartment. Conversely, the C-3000 performs equally as well in installations where C.O. lines are present. An individual C-3000 module has a 12-tenant capaci­ty; for larger applications, a maximum of eight (8) C-3000 modules can be intercon­nected, allowing a total system capacity of up to 96 tenants. A C-3000 system con­sists of at least one Master C-3000 module, and as many as seven Slave modules.
B. C-3000 Apartment Entry System
The K-1900-9 may be used with any standard Touch Tone phone to provide single number (hot-line) or multi-number speed dialing. The K-1900-9 is capable of storing 100 telephone numbers in non-volatile E
2
memory and will operate on any standard
loop start C.O. line or analog PABX/KSU station with a standard Touch Tone phone.
When programmed as a multi-number dialer, the K-1900-9 will allow the user to enter a 1 or 2 digit Touch Tone code which will trigger the unit to speed dial one of up to 100 different telephone numbers. When programmed as a single number hot-line dialer, the K-1900-9 will dial a single pre-programmed number when any off-hook condition is detected on the “PHONE” port. The K-1900-9 can also be used as an alarm dialer, initializing speed dialing from a contact closure.
D. K-1900-9 AC Powered Single or Multi-Number Dialer
PPrroodduuccttSSuuppppoorrttLLiinnee......771155..338866..8866666
6
FFaaxxBBaacckkLLiinnee......771155..338866..4433445
5
?
?
?
Need More Information on the K-1900-3?
Call (715) 386-4345 and select 312.
Need More Information on the C-2000?
Call (715) 386-4345 and select 156.
Need More Information on the K-1900-9?
Call (715) 386-4345 and select 321.
?
Need More Information on the C-3000?
Call (715) 386-4345 and select 162.
Loading...