Venturer PLV16070 User Manual

PLV16070

Portable Digital TV

7” widescreen LCD

Instruction Manual

Need More Help?

DO NOT RETURN THIS PRODUCT TO THE STORE

Please visit online help at

http//www.venturer.com

SAFETY PRECAUTIONS

The lightning flash with an arrowhead symbol, within the equilateral triangle, is intended to
alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure
that may be of sufficient magnitude to cause an electric shock.

The exclamation point within the equilateral triangle is intended to alert the user to the presence
of important operating and maintenance (servicing) instructions in this owner’s manual.

WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.

WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS APPLIANCE
TO RAIN OR MOISTURE. DO NOT PLACE OBJECTS FILLED WITH LIQUIDS ON OR

NEAR THIS UNIT.

WARNING: SHOULD ANY TROUBLE OCCUR, DISCONNECT THE AC POWER

ADAPTER AND REFER SERVICING TO A QUALIFIED TECHNICAN.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined
by turning the equipment off and on, the user is encouraged to try to correct the interference by one
or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

Shielded cables must be used with this unit to ensure compliance with the Class B FCC limit.

WARNING:
Changes or modifications not expressly approved by the party responsible for compliance could void

the user’s authority to operate the equipment.

- 1 -

- 2 -

IMPORTANT SAFETY INSTRUCTIONS

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with a dry cloth.

7. Do not block any of the ventilation openings.

Install in accordance with the manufacturer’s
instructions.

8. Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce
heat.

9. Do not defeat the safety purpose of the
polarized or grounding - type plug. A polarized
plug has two blades with one wider than the
other. A grounding type plug has two blades
and a third grounding prong. The wide blade
or the third prong is provided for your safety.
When the provided plug does not fit into your
AC power outlet, consult an electrician for
replacement of the obsolete outlet.

10. Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.

11. Only use attachments/accessories specied

by the manufacturer.

CONTENT

Safety Precautions ......................................... 1

Important Safety Instructions ........................ 2

Content ......................................................... 2

Accessories ................................................... 3

Remote Control ............................................. 3

Quick Start Guide ......................................... 4

Control Reference Guide .......................... 5-6

Connections .............................................. 7-8

Connecting a TV Antenna / Cable / Satellite . 7

Connecting a Digital antenna .....................8

Using Headphones / Earphones ................. 8

Using the Flip-out Stand ................................. 8

Power Supply .......................................... 9-10

Using the AC Adapter ................................ 9

Using the Car Power Adapter .................... 9

Using the Built-in Battery ........................ 10

Turning on the Unit ................................. 10

12. Use only wi th a cart,
sta nd, tri pod, bracket,
or table specified by the
manufacturer, or sold with
the apparatus. When a cart
is used, use caution when

moving the cart/apparatus

combi natio n to avo id
injury from tip-over.

13. Unplug this apparatus during lightning storms
or when unused for long periods of time.

14. Refer all servicing to qualified service
personnel. Servicing is required when the
apparatus has been damaged in any way, such
as the power-supply cord or plug is damaged,
liquid has spilled or objects have fallen into the
apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally,
or has been dropped.

TV Setting ............................................. 11-14

Picture Menu .......................................... 11

Audio Menu ............................................ 11

Time Menu .............................................. 12

Setup Menu ....................................... 12-13

Channel Menu ................................... 13-14

Maintenance ............................................... 14

Troubleshooting Guide ................................ 15

Portable Cart

Warning

- 3 -

ACCESSORIES

Remote control with batteries ................................................................................................... x 1

Car power adapter .......................................................................................................................... x 1

AC adapter ............................................................................................................................... x 1

Auxiliary antenna ........................................................................................................................... x 1

REMOTE CONTROL

• Point the remote control at the REMOTE SENSOR located on the unit.

• When there is a strong ambient light source, the perform ance of the infrared REMOTE SENSOR

may be degraded, causing unreliable operation.

• The recommended effective distance for remote operation is about 16 feet (5 meters).

To Install Batteries

1. Open the battery door.

2. Insert two AAA batteries.

Battery Replacement

When the batteries become weak, the operating distance of the remote control is greatly reduced
and you will need to replace them.

CAUTION: Danger of explosion if battery is incorrectly replaced. Replace only with the
same or equivalent type.

Notes:

• If the remote control is not going to be used for a long time, remove the batteries to avoid corrosion

damage caused by battery leakage.

• Do not mix old and new batteries. Do not mix ALKALINE, standard (CARBON-ZINC) or rechargeable

(NICKEL-CADMIUM) batteries.

• Always remove batteries as soon as they become weak.

• Weak batteries can leak and severely damage the remote control.

WARNING: Do not dispose of batteries in a fire. Batteries may explode or leak.
Many universal remote controls have a “learning” feature. We recommend you use that feature to
program the remote control.
For any questions or problems related to programming a universal remote control, you must contact
the customer service department of the universal remote control manufacturer for assistance, or
refer to the instructions included with the universal remote control. We cannot offer assistance in
programming universal remote controls.

- 4 -

QUICK START GUIDE

Setup Wizard

Please select your prefer language :

Menu Language English

Go to next step :

MENU

ENTER

TURNING ON THE UNIT FOR THE FIRST TIME

The first time you turn on the unit, the unit will enter the setup mode. You can easily follow the prompt

message on the screen to complete basic TV settings.

Make sure the TV antenna has been connected properly to the ANTENNA RF IN Terminal
on the side of the TV.

1. Press the / button to select your preferred

On-screen menu language. Use the /

button to highlight “Go to next step:“ and

press the ENTER button to enter next setup
screen.

2. Use the

different items, then press the / button
to select the desired options. Use the /

button to move the highlight bar on “Go to

next step:“ and press the ENTER button to
enter next setup screen.

3. Use the

press the / button to select Air or Cable.

Highlight “Go to next step:“ and press the

ENTER button to start scanning channels.

4. After scanning nishes, the system will return to the rst TV channel scanned.

/ button to switch between

/ button to select Air/Cable, then

Setup Wizard

Select the time zone & Daylight saving time:

Time Zone Pacific

DST Off

Time Format 24-hour

Go to next step :

MENU

Setup Wizard

Select the antenna type then auto scan:

Air / Cable Air

Cable System AUTO

Go to next step :

MENU

ENTER

ENTER

- 5 -

CONTROL REFERENCE GUIDE

SIGNAL

Remote Control

1) MUTE Button

Press to turn off the sound.

2) MENU Button

Press to display the on-screen menu or switch

back to the previous menu screen.

3) CURSOR (

Use to highlight selections on a menu screen

and adjust certain settings.

ENTER Button

Confirm selection on a menu screen.

4) DISPLAY Button

Press to display information about the current

TV channel.

5) VOL + / VOL - Buttons

Press to adjust the volume level.

6) LAST CH

Press to switch to previously selected TV

channel.

7) SIGNAL Button

Press to display TV signal quality.

8) CC Button

Press to turn on or change settings for the Closed

Caption feature.

9) LCD MODE Button

Press to select the desired screen aspect ratio

- 4:3, Wide (16:9), or Auto - for the particular

program you’re watching.

10) CH

Press to s elect the chann el upwar d or

downward.

11) NUMERIC Buttons

Press to enter numbers or go directly to a specific

channel.

12) • [dot] Button

Press to enter digital TV sub-channels with the

numeric buttons (i.e. 11.3 or 12.7).

, , , ) Buttons

/ CH Buttons

- 6 -

Unit

CONTROL REFERENCE GUIDE

1) Screen

2) ENTER Button

Confirm selection on a menu screen.
MENU Button
Press to display the on-screen menu or switch

back to the previous menu screen.

CH + / CH - Buttons

Press to select the channel upward or

downward.

VOL + / VOL - Buttons

Press to adjust the volume level.

3) Speaker

4) Remote Sensor

Receives infrared signals from the remote

control.

5) Flip-out Stand

6) Direct-connect antenna connecting to the
ANTENNA RF IN Terminal

7) HEADPHONE Jack

8) ON /

ON position: Turns TV ON, green indicator

Charge position: Recharges the battery, red

9) DC IN 9V - 12V Jack

Connect the supplied AC adapter.

/ Charge Switch

will be ON.

position: Puts TV in standby mode.

indicator will be ON.

- 7 -

CONNECTIONS

3

Connecting a TV Antenna / Cable / Satellite

To view television channels correctly, a signal must be received from one of the following sources:

- An indoor or outdoor aerial antenna

- A cable system

- A satellite system

Using Direct-Connect Antenna

To optimize TV reception, try adjusting the

orientation and position of the direct-connect
antenna.

Using a Different Antenna

To TV ANTENNA terminal

(cable not included)

Removing Direct-Connect Antenna Before
connecting a different antenna or a coaxial
cable, you need to remove the direct-connect
antenna first.

Hold the direct-conne ct antenna
and rotate the nut as shown below
to remove.

Cable TV (without a CATV converter)

Combination VHF/UHF antenna
(ATSC / NTSC signal)

Separate VHF/UHF antenna
(ATSC / NTSC signal)

Auxiliary antenna
(included with this product)

How to connect the Auxiliary Antenna

1. Hold the connector of auxiliary antenna and rotate
the nut to the ANTENNA RF IN terminal on the

side of the TV.

2. Remove the cap on the base of Auxiliary Antenna.

3. Hold the antenna rod of Auxiliary Antenna and rotate
the nut to the base until it is fastened.

4. Extend the antenna rod and adjust position for
optimal reception.

- 8 -

Headphones / Earphones

(3.5mm diameter plug)

CONNECTION

NOTE
Optimal indoor reception of over-the-air TV broadcasts is typically achieved using an external
fixed antenna. You may find that indoor reception is adequate using the direct-connect antenna.
However, for your convenience, we’ve also included an additional antenna with a long cable to
give you extra flexibility in antenna placement. In general, you’ll often find that placement of the
antenna near windows, or at higher elevations, should improve reception. If you seek to further
improve reception, we recommend you purchase the appropriate antenna that is suitable for your
particular environment.

Connecting a Digital Antenna

The tuner in this TV receives ATSC TV signals from an antenna.
This digital TV can receive standard (SDTV) and high denition (HDTV) over the air broadcasts.

Using Headphones / Earphones

• Turn down the volume before connecting headphones

to the unit, then adjust the volume to your desired
level.

• When headphones are connected, no sound will come

from the front speaker.

CAUTION:

Avoid listening to sound at high levels for prolonged
periods of time. This may be harmful to you and may
cause hearing loss.

USING THE FLIP-OUT STAND

The stand is located on the rear panel of the unit. Pull
the stand out and rotate it to the maximum angle (shown
as right).

- 9 -

POWER SUPPLY

To DC IN
9-12V jack

To AC
outlet

AC Power Adapter

To DC IN 9-12V jack

Car Power Adapter

To the cigarette

1

lighter socket

Using the AC Adapter

The supplied 9V adapter operates on AC 120V ~ 60Hz.

Cautions:

• The AC power adapter included with this unit

is for its use only. Do not use it with other
equipment.

• To prevent electrical shock, match wide blade
of plug to wide slot of wall outlet, then fully
insert.

• When the unit is not going to be used for long

time, disconnect the AC power adapter from the
AC power outlet.

• When the AC power adapter is plugged in, the

apparatus is not completely disconnected from
the main power supply, even when the power is
turned off.

• The AC power adapter shall not be exposed to

dripping or splashing and that no objects filled
with liquids, such as vases, shall be placed on
apparatus.

Warning:

The AC power adapter is used as disconnect device and it should remain readily operable during
intended used. In order to disconnect the apparatus from the mains completely, the AC power
adapter should be disconnected from the mains socket outlet completely.

Using the Car Power Adapter

The 12V car power adapter allows the unit to be used with vehicles that have a 12V, negative ground

electrical system.

NOTE: It is not possible to satisfactorily receive ATSC TV signals while in motion - the car power

adaptor is intended for uses such as “tail-gating”.

WARNING:

Disconnect the car power
adapter when not in use. Not

for use in 24V vehicles.

CAUTION:

For continued protection against risk of fire,
replace only with same type and rating of fuse.

Fuse replacement Instructions

Fuse

Press and hold

Press and hold

- 10 -

POWER SUPPLY

Cautions:

• Use the provided 12V car power adapter only. Use with other car power adapters could damage

the unit.

• The 12V car power adapter included with this unit are for its use only. Do not use them with other

equipment.

• In the interest of trafc safety, do not operate this unit while driving a vehicle.

• Make sure the unit is securely fastened to prevent it from falling or ying through the air in the

event of an accident.

• If the inside of the cigarette lighter socket is dirty with ashes or dust, the plug section may become

hot due to poor contact. Be sure to clean the cigarette lighter socket before use.

• After use, disconnect the 12V car power adapter from both the unit and cigarette lighter socket.

Using the Built-in Battery

The unit has a built-in, non-replaceable, rechargeable battery. Charge the built-in battery before using
it for the first time. Before charging, make sure the ON / / Charge switch is slid to Charge Mode
position and the AC power adapter is plugged in. The normal charging time should be completed within
4-5 hours. The red charging light will go out when the built-in battery becomes fully charged.

Warnings:

• The built-in battery can only be recharged when the unit is in CHARGE mode while using the AC

power adapter.

• The built-in battery cannot be recharged when the unit is in ON mode.

• Do NOT recharge the built-in battery in a vehicle using the car power adapter.

• Batteries should not be exposed to excessive heat such as sunshine, re or the like.

Notes:

• When the built-in battery power is low, "

will stop playing.

• Recharge the built-in battery when you are ready to use it again.

• While using the built-in battery, the environmental temperature should be 41°F (5°C) to 95°F
(35°C).

• To get the longest service life of the built-in battery, charge at indoor-temperature.

• The built-in battery in this device may present a risk of re or chemical burn if mistreated. Do not
disassemble, heat above 212°F (100°C), or incinerate.

• The unit should not be exposed to excessive heat such as sunshine, re or the like.

• When discarding the unit, environmental problems must be considered and local rules or laws

governing the disposal of such products must be strictly followed.

Battery Low" will display on the screen and the unit

Turning on the Unit

The supplied AC adapter operates on AC 120V.

• Slide the ON /

the side of unit to turn on the unit - the green power
indicator will light up.

/ Charge Switch to ON mode on

- 11 -

TV SETTING

Picture

Picture Mode
Contrast
Brightness
Sharpness
Color
Color T
LCD Mode Wide

emp

Standard

Normal

50
50

50
50

MENU

ENTER

Audio

Audio Channel

Primary Audio

MENU

ENTER

Picture Menu

1. Press the MENU button.

2. Use the

(Picture Mode, Contrast, Brightness, Sharpness,
Color, Color Temp or LCD Mode). Adjust them
using the or button (Screen will change to
your desired setting).

3. Repeat step 2 to adjust other options.

4. To exit the MAIN MENU and return to the normal

screen, press the MENU button repeatedly.

or button to select the options

Picture Mode : Select from preset screen display settings to match the type of show you are watching

(Standard, Dynamic, Soft and Personal). Select Personal mode to recall your custom
settings on contrast, brightness, sharpness and color.

Contrast : Adjust the contrast of the picture. The black portions of the picture become richer

in darkness and the white become brighter.

Brightness : Adjust the brightness of the picture. Brighten or darken the whole picture.
Sharpness : Adjust the sharpness level to improve detail in the picture.
Color : Adjust the color of the picture.
Color Temp : Adjust the color temperature of the picture. Choose from Normal (balanced), Warm

(red white) or Cool (blue white) modes.

LCD Mode : Set the LCD display ratio. Choose from Auto, 4:3 or Wide modes.

Audio Menu

1. Press the MENU button.

2. Use the

3. Adjust it using the

4. To exit the MAIN MENU and return to the normal

NOTE:

Some TV stations may broadcast more than one audio channel for a particular TV channel. For example,

it may broadcast in English Language on its primary audio channel, while broadcasting in Spanish, or

broadcasting Descriptive Audio (for the Visually-Impaired) on a secondary audio channel.

or button to select Audio, then press

the button to enter the Audio settings.

or button.

screen, press the MENU button repeatedly.

- 12 -

TV SETTING

Time

Time Zone
DST
Time Format

Clock

Pacific

Off

24-hour

-- -- / -- /-- --:--

MENU

ENTER

Setup

Menu Language
Transparency
Menu Time-Out
Closed Caption

Restore Default

English

25%

15 Sec.

MENU

ENTER

TIME Menu

1. Press the MENU button.

2. Use the

3. Use the

4. Repeat step 3 to adjust other options.

5. To exit the MAIN MENU and return to the normal

or button to select Time, then press

button to enter the Time settings.

the

or button to select the options (Time
Zone, DST or Time Format). Adjust them using
the or button.

screen, press the MENU button repeatedly.

Time Zone : Select the time zone from Pacic / Alaska / Hawaii / Atlantic / Eastern

/ Central / Mountain.

DST (Daylight Saving Time) : Select On to activate daylight saving time.
Time Format : Select the time format 12-hour / 24-hour.
Clock : Display the current time.

SETUP Menu

1. Press the MENU button.

2. Use the

3. Use the

4. Press the MENU button to return to the previous

5. Repeat steps 3 and 4 to adjust other options.

6. To exit the MAIN MENU and return to the normal

Menu Language : Select On-screen menu language from English / French / Spanish.
Transparency : Set the transparency of the On-Screen Menus.
Menu Time-Out : Once the interval period is set, the On-Screen Menu will disappear from the screen

Restore Default : If you reset the TV to the factory settings, all your present settings on PICTURE and

or button to select Setup, then press
the button to enter the Setup settings.

or button to select the options (Menu

Language, Transparency, Menu Time-Out, Closed
Caption or Restore Default). Adjust them using

the or button (Screen will change to your
desired setting); or press the button to go into
the detailed settings.

menu.

screen, press the MENU button repeatedly.

when it reaches the preset interval time. The available values are: 5 Sec., 15 Sec.,

30 Sec., 45 Sec. or 60 Sec.

AUDIO will be erased and replaced by the factory’s default settings.

- 13 -

Closed Caption

Setup

Analog Closed Caption
Digital Closed Caption
Option

CC1

Service1

CC Mode CC Off

MENU

ENTER

Channel

Air/Cable
Auto Scan
Auto Scan Add CH
Channel Skip
Channel No.
Channel Label

DTV Signal

Air

5.1

KTLA-DT

Good

MENU

ENTER

TV SETTING

CC Mode : Select closed caption On,

Off or CC on Mute.

Analog Closed Caption : Select the analog closed

caption or turn it off.

Digital Closed Caption : Select between different

digital closed captions or
turn it off.

Option : Select as Default to use

the default digital caption
style of the broadcaster.
Select Custom to activate
the caption style items and
set your desired detailed
settings.

Channel Menu

1. Press the MENU button.

2. Use the
press the button to enter the TV settings.

3. Use the

Cable, Auto Scan, Auto Scan Add CH, Channel
Skip, Channel No. or Channel Label). Adjust them

using the or button, or press the button to
go into the detailed settings.

4. Press the MENU button to return to the previous
menu.

5. Repeat steps 3 and 4 to adjust other options.

6. To exit the MAIN MENU and return to the normal

screen, press the MENU button repeatedly.

Cable/Air : Cable and Air modes are available.
Auto Scan : Search for available channels and store them in memory.
Auto Scan Add CH : Search for more available channels and add them in memory. The channels

Channel Skip : Skip weak channels and the channels you don’t like.
Channel No. : Displays currently-selected TV channel.
Channel Label : Display and edit the channel label.
DTV Signal : Display the signal strength (for digital TV channels only).

or button to select Channel, then

or button to select the options (Air/

previously stored are retained. This is very useful if you find you need to
have antenna in different orientations for reception of particular channels

- and thus wish to perform multiple scans.

- 14 -

TV SETTING

Channel Skip

1. Use the or button to select a channel. (Press the button to select the last channel of the
page; press again to go to the next page. Press the button to select the first channel of the page;
press again to return to the previous page.)

2. Press the ENTER button to shift between On / Off. (Select ON to skip the selected channel. The
channel will not appear when you press the CH

/ CH button.)

Channel Label

You can edit a label for each channel.

1. Use the or button to select the number or letter. Use the or button to move and edit the
next character.

2. After editing, the Channel and Channel Label will be shown on the screen when you press the

DISPLAY button.

MAINTENANCE

Cleaning the Unit

• Be sure to turn the unit off and disconnect the AC adapter before maintaining the unit.

• Wipe the unit with a dry soft cloth. If the surfaces are extremely dirty, wipe clean with a cloth that

has been dipped in a weak soap-and-water solution and wrung out thoroughly. Wipe with a dry
cloth.

• Never use alcohol, benzine, thinner, cleaning uid or other chemicals. Do NOT use compressed

air to remove dust.

As concerns grow about the environmental impact of outdated electronic products,

Venturer Electronics is committed to being a part of the solution. Free of charge,
Venturer Electronics customers can return qualifying units to us for recycling.
For more details, please visit our website at www.venturer.com/recycle or
call 1-800-252-6123.

- 15 -

TROUBLESHOOTING GUIDE

SYMPTOM CAUSE (AND REMEDY)

Unit does not work.

No pi ct ure on the TV

screen.

No sound.

Remote control does not
work.

Can not watch a bilingual

TV program in its secondary

language.

Weak signal or channel not
available.

TV can not receive signal

from a connected Cable
box or Satellite box.

Ca n I wat ch TV whi le
holding the TV, or while

traveling in a vehicle ?

• Unplug the AC power cord and plug it back in.

• Check that the three-way switch is slid to “ON” position.

• Choose different chann els on the TV set unti l the picture

appears.

• Make sure the TV sound is not muted.

• Make sure the batteries are inserted correctly.

• Replace the batteries if they are exhausted.

• Remove any obstacles between the remote control.

• Use the remote near the unit.

• Point the remote at the remote sensor on the unit.

• Make sure you have correctly selected the appropriate audio
setting (see p. 11). Please note that not all TV stations broadcast a

secondary language.

•

Try to reposition the antenna.

NOTE: Optimal reception of over-the-air TV broadcasts is typically

obtained using an external fixed antenna. Orientation and location
of the antenna is typically critical for best results - if using indoors,
you may find that placement of the antenna near a window, or in
an elevated location, improves performance.

• Conrm that a Coaxial cable is connected properly to the TV and

the Cable or Satellite box. Ensure that your Cable or Satellite box

is congured to output a TV signal over a Coaxial cable.

• No - ATSC TV signals can’t be received satisfactorily while TV is in
motion. The TV and Antenna should be stationary and positioned

for optimal reception. Note: the Car Power Adapter is provided
specifically for “tail-gating” usage.

Specifications and external appearance are subject to change without notice.

Need More Help?

DO NOT RETURN THIS PRODUCT TO THE STORE

Please visit online help at

http//www.venturer.com

Printed in China

811-160791W010