Venturer KLR33688B User Manual
KLR33688B
EN - FR
User manual
Manuel de l’utilisateur
It is important to read this instruction book prior to using your new product for the rst time.
Il est important de lire ce manuel d’utilisation avant l’utilisation initiale de ce nouveau produit.
EN - FR - 2
Safety Precautions
FCC INFORMATION
This device complies with Part 15 of the FCC
rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful
interference, and (2) This device must accept
any interference received, including interference
that may cause undesired operation.
NOTE: This equipment has been tested and
found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable
protection against harmful interference in a
residential installation. This equipment generates,
uses, and can radiate radio frequency energy
and, if not installed and used in accordance with
the instructions, may cause harmful interference
to radio communications. However, there is no
guarantee that interference will not occur in a
particular installation. If this equipment does
cause harmful interference to radio or television
reception, which can be determined by turning
the equipment off and on, the user is encouraged
to try to correct the interference by one or more
of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the
equipment and receiver.
• Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV
technician for help.
WARNING:
• Changes or modications to this unit not
expressly approved by the party responsible
for compliance could void the user’s authority
to operate the equipment.
• The AC adapter is used as disconnect device
and it should remain readily operable during
intended used. In order to disconnect the unit
from the mains completely, the AC adapter
should be disconnected from the mains socket
outlet completely.
• The AC adapter of unit should not be
obstructed OR should be easily accessed
during intended use.
• Minimum 10 cm (4 inches) distances around
the unit for sufcient ventilations.
• The ventilation should not be impeded by
covering the ventilation openings with items
such as newspaper, table-cloths, curtains, etc.
• No naked ame sources such as lighted
candles should be placed on the unit.
ON SAFETY
• Disconnect the AC adapter immediately if
liquid spills into or onto the unit, or if an object
falls into the unit. The unit should not be used
until service by a qualied service personnel is
completed.
• The unit shall not be exposed to dripping or
splashing and that no objects lled with liquid,
such as vases, shall be placed on the unit.
ON USE
Never use the unit where it would be subject to:
- Heat sources such as radiators or air ducts.
- Direct sunlight.
FOR CUSTOMERS IN CANADA
This apparatus complies with the Class B
limits for radio noise emission set out in radio
interference regulations.
CAN ICES-3 (B) / NMB-3 (B)
CAUTION
TO REDUCE THE RISK OF FIRE, DO NOT
PLACE ANY HEATING OR COOKING
APPARATUS BENEATH THIS UNIT.
This device complies with Industry Canada
Licence-exempt RSS-210. Operation is
subject to the following two conditions: (1)
this device may not cause interference, and
(2) this device must accept any interference,
including interference that may cause undesired
operation of the device.
EN - FR - 3
TOOLS NEEDED:
1) Electric drill with 1/4” bit;
2) Phillips-head (cross style) screwdriver.
STEP 1
If your cabinet does NOT have an overhang:
a) Place the Mounting Template in the desired location
inside or underneath the cabinet (whichever has less
obstructions, and will be easier for you to reach to drill
holes), ush with the front edge of the cabinet and
tape it down. Go to STEP 2.
If your cabinet DOES have an overhang:
a) Measure the thickness “T” of the cabinet overhang
(see Figure 1).
b) Fold the Mounting Template along the guideline that
is closest to the thickness of your cabinet overhang.
c) Tape Mounting Template to the underside of the
cabinet with the folded portion of the Mounting
Template ush up against the cabinet overhang (see
Figure 2). Go to STEP 2.
STEP 2
Use an electric drill with a ¼” drill bit (not included) to drill
all three holes marked on the Mounting Template (see
Figure 3). To reduce splintering, place a small piece of
masking tape over each hole location before drilling. Go
to STEP 3.
STEP 3
If your cabinet does NOT have an overhang:
a) SIX screws are included with this unit, but you will
only need three of them. Select the screw length
which will go completely through your cabinet bottom,
and provide at least 3/8” of thread to screw into the
unit.
b) Insert the three selected screws through each hole
from the inside of the cabinet going down (see Figure
4).
Warning:
Please follow the steps below for proper mounting:
1. We recommend you install the 3 screws using
hand tools. Do not use power tools because high
torque can damage the threads on the main unit.
2. Please hold and support the unit before you insert
any of the screws.
3. First mount 2 screws on opposite corners of the
unit.
c) Hold the unit up against the bottom of the cabinet, and align the three holes on the top of the unit
with the screws. Partially tighten each screw, but do not fully tighten the screws until all of them
have been started.
d) Gently tighten each screw until they are rmly holding the unit in place.
Mounting Instructions
EN - FR - 4
If your cabinet DOES have an overhang:
a) SIX screws are included with this unit, but you will only
need three of them. Select the screw length which
will go completely through your cabinet bottom, and
extend at least 3/8” past the bottom of your cabinet
overhang.
b) This unit includes two sets of three spacers of various
lengths. The spacers can be put together to form longer
spacers to accommodate various cabinet overhang
thicknesses. Determine the best combination of
spacers which is equal to or longer than the cabinet
overhang thickness.
c) Insert the three selected screws through each hole
from the inside of the cabinet going down (see Figure
5).
Warning:
Please follow the steps below for proper mounting:
1. We recommend you install the 3 screws using hand
tools. Do not use power tools because high torque
can damage the threads on the main unit.
2. Please hold and support the unit before you insert
any of the screws.
3. Mount 2 screws on the corners of the unit rst.
4. Do not reverse the spacer.
d) Hold each screw head down and push the unit and
spacers onto the screws, then hold the unit up until
spacers are rmly against the bottom of the cabinet
(and fully nested within each other if you are using
multiple spacers for each screw).
e) Partially tighten each screw, but do not fully tighten the
screws until all of them have been started (see Figure
6).
f) Gently tighten each screw until they are rmly holding
the unit in place. The top front edge of the unit should
clear the overhang.
MOUNTING SUGGESTIONS
1) If your cabinet has obstructions inside it which prevent
you from using the template, cut out the corresponding
area on the template, but do NOT cut out or through
the screw holes.
2) If your cabinet has obstructions underneath it, which
will interfere with the mounting of the unit, remove the
obstruction before mounting the unit, or nd another
location to mount the unit.
3) It is recommended that you wear safety glasses while drilling to prevent eye injuries.
4) For wood cabinets, you may want to mark the hole locations with a nail, pressed gently but rmly
into the wood so that a slight impression is made. This will also help keep the drill bit centered in
the right location.
5) Hold the drill rmly against the cabinet to keep the drill from “walking”.
Loading...