Page 1
PORTABLE
NAVIGATION
DEVICE
HPS9308
Need More Help?
DO NOT RETURN THIS
PRODUCT TO THE STORE
Please visit online help at
http://www.venturer.com
- 1 -
User Manual
Page 2
Thank you for choosing this Navigator as your door-to-door in-car
navigator. The memory card version is very easy to use.
Read the Quick Start Guide rst and start using this Navigator right
away. This document is the detailed description of the software.
Although this Navigator can easily be discovered by experience, it
is still recommended that you read through this manual to clearly
understand the exact function of each button and icon.
Warnings and Safety Information
1
This Navigator is a navigation system that helps you nd your way
to your selected destination. It will determine your exact location
with the help of a built-in GPS receiver. The position information
obtained from the GPS receiver will not be transmitted anywhere,
so others will not be able to track you.
If you are the driver of the vehicle, we recommend that you operate
this Navigator before beginning your journey. The driver’s attention
should be on the road. Plan your route before departure and pull
over if you need to change route parameters. This Navigator has a
built-in (optional) Safety Mode that will prevent you from using the
screen functions if your car is in motion. Unless a passenger will be
the only one to operate this Navigator, we strongly encourage you
to turn on the Safety Mode.
It is also important that you look at the display only if it is absolutely
safe to do so.
You should always observe trafc signs and road trafc before you
obey any instruction from this Navigator. If you need to deviate from
the recommended direction, this Navigator will suggest a modied
route according to the new situation.
Never place this Navigator where it can obstruct the view of the
driver, is within the deployment zone of airbags, or where it can
cause injuries in case of an accident.
- 2 -
Page 3
General Information
2
This Navigator is a navigation system optimized for in-car use. It
provides door-to-door navigation for both single and multi-point
routes using adaptable route parameters. This Navigator is capable
of planning routes throughout the whole map region installed on the
memory card. Unlike some other products, this Navigator does not
require that you change maps or switch to a poorly detailed general
map to navigate between map segments or countries. You always
have complete freedom to go wherever you wish.
A stylus to use this Navigator is located on the lower right rear of
the Navigator. All screen buttons and controls are designed so that
you can operate them with your ngertips, or stylus.
When using this Navigator, you do not need to ‘double tap’ or ‘tap
and hold’ the touch screen as these functions cannot be used
reliably in a moving vehicle. A single tap triggers most of the screen
controls. The only exceptions are ‘drag and drop’ for moving the
map, or scaling it in MAP mode (6.5.6).
Most of the screens have a Return ( ) button in the top left
corner. This arrow returns to the previous screen or directly to
one of the map screens.
Setting screens also have a Help ( ) button in the top right
corner. This will show a detailed description of the current
settings screen.
- 3 -
Page 4
Table of Contents
1 Warnings and Safety
Information ........................... 2
2 General Information .............. 3
3 How to Mount the Bracket to
the Windshield ....................... 7
4 Connection .......................... 9
5 Operation ............................. 10
5.1 Hardware Buttons .......... 10
5.1.1 Turn On the
Navigator .............. 11
5.1.2 Zoom In and Out ............. 11
5.2 Screen Buttons and Controls
.......................................... 12
5.2.1 List Selectors .................. 12
5.2.2 Sliders ............................ 12
5.2.3 Switches ......................... 13
5.2.4 Switches in the Quick Menu .
........................................ 13
5.2.5 Virtual Keyboards ........... 13
5.2.5.1 ABC-type Keyboards . 13
5.2.5.2 QWERTY-type Keyboards
................................... 14
5.2.5.3 The Numeric Keyboard ..
.................................... 14
6 Discovering the Program
through the Screens ............ 15
6.1 Main Menu ...................... 15
6.2 About Screen .................. 16
6.3 The Map .......................... 16
6.3.1 2D and 3D Map Views .... 17
6.3.2 Zoom Levels .................... 18
6.3.3. Day and Night Color
Schemes ......................... 19
6.3.4 Streets and Roads ........... 20
6.3.5 Other Objects .................. 21
6.3.6 Current Position and Lock-
on-Road ......................... 21
6.3.7 Selected Map Point
(Cursor) ......................... 22
6.3.8 Marked Map Points (Pin) ...
....................................... 23
6.3.9 Visible POIs (Point of
Interest) ........................ 24
6.3.10 Elements of the Action
Route ............................ 26
6.3.10.1 The Start Point,
Via Points and the
Destination ......... 26
6.3.10.2 Animated Turn Guidance
................................. 26
6.3.10.3 The Active Leg of the
Route ........................ 26
6.3.10.4 Inactive Legs of the Route
................................. 27
6.3.10.5 Roads in the Route
Excluded by your
References ............... 27
6.4 GPS Data Screen ............ 28
6.4.1 GPS Data Displayed ...... 29
6.4.2 GPS Connection Indicator ..
........................................ 29
6.4.3 GPS Data Quality Indicator
........................................ 29
6.4.4. Time Synchronization .... 30
6.5 Screens with Map ......... 31
6.5.1 Turn Preview (No. 1) ..... 33
6.5.2 Zoom In and Out (No. 2 and
3) ................................. 33
6.5.3 Tilt Up and Down (No. 4 and
5) .................................. 34
6.5.4 Follow Mode - Lock
to GPS Position and
Heading (No. 6) ....... 34
6.5.5 Cursor (No. 7) ............... 35
6.5.6 Map Scale (No. 8) ......... 35
6.5.7 Menu (No. 9) ................. 35
6.5.8 Map Orientation and
Overview (No. 10) ......... 35
6.5.9 GPS Position Quality (No.
11) ................................. 36
6.5.10 Battery Status (No. 12) .. 37
6.5.11 Sound Muting (No. 13) . 37
6.5.12 Track Log Recording/
Playback Indicator (No. 14)
....................................... 38
- 4 -
Page 5
6.5.13 Cursor Menu (No. 15) ... 38
6.5.14 Current Street (No. 16) .. 40
6.5.15 Travel and Route Data (No.
17) ................................ 40
6.5.16 Distance to Next Turn (No.
18) ................................ 41
6.5.17 Next Street / Next City (No.
19) ................................ 41
6.5.18 Approaching Next Turn (No.
20) ................................ 41
6.6 Route Information Screen ..
.......................................... 42
6.6.1 Route Data Displayed (for
Destination and Via Points ...
......................................... 42
6.6.1.1 Route Line .................. 43
6.6.1.2 Distance Left ............. 43
6.6.1.3 Method ...................... 43
6.6.1.4 Time Left ................... 44
6.6.1.5 Estimated Arrival ....... 44
6.6.1.6 Destination / Via Point .....
................................... 44
6.6.2 Warnings Icons ............... 44
6.6.3 Fit to Screen ................... 45
6.6.4 Parameters .................... 45
6.7 Menu .............................. 46
6.7.1 Find Tab .......................... 46
6.7.2 Quick Tab ........................ 46
6.7.2.1 3D Map ..................... 46
6.7.2.2 Zoom and Tilt (Switch) ......
.................................... 47
6.7.2.3 Night Mode (Switch) .......
................................... 47
6.7.2.4 Manage POI (Point of
Interest) ..................... 47
6.7.2.5 Popup Information
(Switch) ....................... 51
6.7.2.6 Manage Track Logs .. 51
6.7.3 Route Tab ....................... 53
6.7.3.1 Recalculate ............... 53
6.7.3.2 Delete ....................... 54
6.7.3.3. Itinerary ..................... 55
6.7.3.4 Fly Over .................... 57
6.7.3.5 Edit ............................ 57
6.7.3.6 Info ............................ 58
6.7.4 Main Button ..................... 58
7 Settings ................................ 59
7.1 General Settings ............ 59
7.1.1 Safety Mode ................... 59
7.1.2 Set Favorite Destinations ....
........................................ 60
7.1.3 Automatic Night Colors .. 60
7.1.4 Alerts .............................. 61
7.1.4.1 Warn When Speeding ....
................................... 61
7.1.5 Route Recalculation ....... 62
7.1.5.1 Automatic .................. 62
7.1.5.2 Ask First .................... 63
7.1.5.3 Disabled .................... 63
7.2 Map Settings ................... 64
7.2.1 Day / Night Color Prole ...
..................................... 64
7.2.2 Alternative Road Names ......
........................................ 64
7.2.3 Show Street Labels ........ 64
7.2.4 Textured Polygons ......... 64
7.3 Sound Settings ............... 65
7.3.1 Master Sound Volume/Switch
........................................ 65
7.3.2 Voice Guidance Volume/
Switch ............................. 65
7.3.3 Key Sound Volume/Switch ...
......................................... 66
7.3.4 Dynamic Volume ............ 66
7.3.5 Attention Tone ................ 66
7.4 Route Parameter Settings ...
.......................................... 67
7.4.1 Method ........................... 67
7.4.2 Route ............................. 67
7.4.2.1 Fast ........................... 67
7.4.2.2 Short .......................... 67
7.4.2.3 Economical .............. 67
7.4.3 Vehicle ........................... 68
7.4.4 Road Types to Include/
Exclude ........................... 68
7.4.4.1 Unpaved Roads ....... 68
7.4.4.2 Highways ............... 68
7.4.4.3 Ferries ..................... 68
- 5 -
Page 6
7.4.4.4 U-turns ..................... 69
7.4.4.5 Permit Needed ......... 69
7.4.4.6 Toll Roads ................ 69
7.5 Language and Navigators .....
........................................... 70
7.5.1 Program Language ......... 70
7.5.2 Voice Language .............. 70
7.5.3 Navigators ........................ 70
7.5.4 Set Date and Time Format ...
........................................ 70
7.6 Advanced Settings ......... 71
7.6.1 Display Options ............... 71
7.6.1.1 2D in Map Mode (and
North-up Orientation) ....
.................................. 71
7.6.1.2 3D in Cockpit Mode (and
Track-up Orientation) .....
.................................. 72
7.6.1.3 Zoom In After Find .... 72
7.6.1.4 Coordinate Display
Format ...................... 72
7.6.1.5 Cockpit Screen Layout ..
.................................. 72
7.6.2 Backlight Settings ........... 73
7.6.2.1 Power Management .....
................................. 73
7.6.2.2 Brightness ............... 73
7.6.3 Smart Zoom ................... 73
7.6.3.1 Smart Zoom Settings ....
.................................. 74
7.6.3.2 Enable Overview Mode .
................................. 74
7.6.3.3 Restore Lock-to-Position
and Smart Zoom ...... 74
7.6.4 Route Options ................. 76
7.6.4.1 Off-Route Sensitivity and
Recalculation Delay ......
................................. 76
7.6.4.2 U-turn Penalty .......... 77
7.6.4.3 Cross-Border Planning .
.................................. 77
7.6.4.4 Carpool Lanes ............ 77
7.6.4.5 Keep Position on Road
(Lock-on-Road) ....... 77
7.6.5 User Data Management .......
........................................ 77
7.6.5.1 Backup Data ............ 78
7.6.5.2 Restore Data ........... 78
7.6.5.3 Remove Pins ........... 78
7.6.5.4 Clear Data ............... 78
7.6.5.5 Reset Advanced
Settings ................... 78
8 Find ...................................... 79
8.1 Find & GO (Main Menu) .......
.......................................... 79
8.2 Selection by Tapping the
Map ................................. 79
8.3 Using the Find Menu ..... 80
8.3.1 Find an Address, Street,
Intersection or City ......... 80
8.3.1.1 Selecting the City, State
and Country to Search In
................................. 81
8.3.1.2 Selecting a Street or the
Center of the City ...... 84
8.3.1.3 Selecting a House
Number or the Midpoint
of the Street ............. 85
8.3.1.4 How to Select an
Intersection Instead of a
House Number ......... 86
8.3.2 Find in History ................ 86
8.3.3 Find Coordinates ............ 87
8.3.4 Find a POI ...................... 88
8.3.5 Find a Favorite Location .. 90
9 Troubleshooting Guide ....... 91
10 Glossary ............................. 93
11 End User License Agreement .
................................................ 97
- 6 -
Page 7
How to Mount the Bracket to the Windshield
3
IMPORTANT NOTICE
This is an Important Notice for users of this Navigation device in
the states of California and Minnesota.
If you are driving in California or Minnesota, you should NOT mount
this Navigator to your windshield. Instead you should use the enclosed
mounting disc to attach the device to your dashboard.
WARNING :
NOTICE TO DRIVERS IN CALIFORNIA AND MINNESOTA:
State law prohibits drivers in California and Minnesota from using
suction mounts on their windshields while operating motor vehicles.
Venturer does not take any responsibility for any nes, penalties, or
damages that may be incurred as a result of disregarding this notice.
(See California Vehicle Code Section 26708(a); Minnesota Statutes
2005, Section 169.71)
This is a permanent solution - the adhesive tape on the bottom
of the mounting disc cannot be removed once xed to your
dashboard.
As an option to windshield mounting, consider using the supplied
dashboard mounting disc.
Step 1 Step 2
mounting
bracket
Step 3 Step 4
peel off
press onto dashboard
for at least 5 seconds
Step 5 Step 6
- 7 -
suction
release
Page 8
Mount the Bracket to the Windshield
1
mounting
bracket
3
4a
2
6
suction
release
To windshield
5
- 8 -
4b
Page 9
Connection
4
Power Supply
Using a Car Plug
A 12V car plug allows the Navigator to be used with vehicles that
have a 12V, negative ground electrical system.
To the Cigarette
Lighter Socket
To Mini
USB
CAUTION
• Use this Navigator only with the included car plug. Use with other car
plugs could damage the Navigator or even your vehicle.
• The included car plug is for use with this Navigator only. Do not use it with
other equipment.
• Make sure the Navigator is fastened securely to prevent it from falling or
ying through the air in the event of an accident.
• When the inside of the cigarette lighter socket is dirty with ashes or dust,
the plug section may become hot due to poor contact. Be sure to clean the
cigarette lighter socket before use.
• After use, disconnect the 12V car plug from both the Navigator and
cigarette lighter socket.
Car Plug
- 9 -
Page 10
Operation
5
This Navigator is designed for easy operation. All controls are
operable by ngertips or stylus. Wherever possible, push buttons
and lists are provided to make accessing functions or changing
settings as easy as possible.
5.1 Hardware Buttons
There are only a few hardware buttons on this Navigator.
The majority of the Navigation functions can be accessed using the
touch screen. The hardware buttons are as follows:
1 2 3 4 5 6 7 8 9
1. Speaker
2. Map Card
3. Touch Screen
Displays the local map. Tap the
screen with the stylus to select
menu commands or enter
information.
4. Button
Press and hold for 2 seconds to
turn the Navigator on or off.
5. Charger Indicator
6. Reset Button
Press to reset the Navigator.
7. Headphone Jack
8. Mini USB (for DC charging)
9. Stylus
Remove the stylus from its
compartment in order to use
it, and replace it after use. The
stylus is for operating the touch
screen.
- 10 -
Page 11
5.1.1
Turn On the Navigator
Press the button and hold
for 2 seconds to turn on the
Navigator.
Select Navigation
If the device power is turned
off while this Navigator is
running, when you turn the
device back on, this Navigator
will continue the navigation
as soon as the built-in GPS
determines the location
again.
While the device is switched
off, the GPS will not work. No
position will be calculated, the
track log will not be saved,
and navigation will stop.
5.1.2 Zoom In and Out
Press the button and hold
for 2 seconds to turn on the
Navigator.
Zoom will change the scale
of the map in both 2D and 3D
map modes. This function is
explained in detail (6.5.2).
After reading, press the
“Accept” button.
NOTE:
When applied on list and menu
screens, this action will move the
highlight up and down.
- 11 -
Page 12
5.2 Screen Buttons and Controls
The primary input channel of this Navigator is the touch screen. If you
read on, you will realize that most parts of the screen are not only used
to display information but also to initiate functions by tapping. Below
you will nd a list of the most frequently used controls in the program.
5.2.1 List Selectors
When the values in the list need
to be named, only the current
value is shown (sometimes
together with a short description)
in a horizontal stripe with arrows
at both ends.
The arrows are buttons. Tap to
move left in the list or tap to
move right. You need not conrm
your selection. As soon as you
leave the screen, the selected
value becomes effective.
5.2.2 Sliders
When a feature has several
different unnamed (numeric)
values, this Navigator will show
sliders to set the desired value.
If the value limits are not displayed
at the ends of the slider, the left
most position means the minimum
value, while the right most position
represents the maximum value.
This control can be operated in
two ways. Either drag the handle
to move the slider to its new
position, or tap the slider where
you want the handle to appear
(handle jumps there immediately).
As with the list selectors, there is
no need to conrm your selection.
As soon as you leave the screen,
the selected value becomes
effective.
- 12 -
Page 13
5.2.3 Switches
When a function can only have
two values (mainly Enabled
and Disabled), a switch is used.
Unlike with list selectors, the
horizontal line contains the name
of the function and not the actual
status. There is a lamp on the left
to show whether the function is
active or not.
When the lamp is dark , the
function is not selected. When it is
lit , the function is enabled. The
whole strip works as a button. Tap
anywhere to toggle between the
enabled and disabled status.
5.2.4 Switches in the
Quick Menu
The switches of Quick menu
(6.7.2) behave as normal
switches but they look different in
order to t in with the other menu
buttons.
Tap the button to toggle between
the enabled and disabled states.
5.2.5 Virtual Keyboards
This Navigator is designed in a way
that you only need to enter letters
or numbers when it is inevitable. In
these cases a full screen keyboard
pops up that can be easily
operated with your ngertips. You
can choose between a separate
ABC and numeric keypad, or a
QWERTY-type keyboard that
contain both letters and numbers.
This Navigator will remember your
last choice and offer it the next
time you need to enter data.
The alphabetic keyboards in this
Navigator do not contain special
characters, because you do not
need to enter accents when
searching for a destination. Type
only the base letters (the letter
most similar to the accented one)
and this Navigator will search
for all their combinations in the
database.
When you type in POI or track
log names, this Navigator will
automatically turn all initials into
capitals to create names that look
pleasant.
5.2.5.1 ABC-type Keyboards
This keyboard contains only
letters. If you wish to enter
numbers, you need to tap the
Keys ( ) button to switch to
the numeric keyboard.
Use Backspace ( ) to delete
the last letter you have entered
if you have made a mistake, tap
- 13 -
Page 14
Space ( ) to enter more
words, and hit Done ( ) to
nish entering the text.
This type of keyboard has large,
nger-friendly buttons.
If you are used to computer
keyboards, you may consider
trying the QWERTY-type
keyboard.
5.2.5.2 QWERTY-Type
Keyboard
QWERTY-type keyboards have
both letters and numbers on
them. The layout is the same as of
the standard QWERTY keyboard.
To switch to the QWERTY-type
keyboard, press the Keys button
until the appropriate keyboard
appears.
The special keys described in
the previous section are also
available here.
5.2.5.3 The Numeric
Keyboard
The numeric keyboard only
contains numbers only, on large
buttons. The special keys you
nd on the other keyboards
(except Space) are available
here as well.
Although QWERTY-type
keyboards also contain number
keys, when entering a house
number, the program offers
the more convenient numeric
keypad.
- 14 -
Page 15
Discovering the Program Through the Screens
6
The best way to discover this Navigator is to explore each screen
in detail, and to nd out how to move from one to another. Read
this chapter for a guided tour.
6.1 Main Menu
This Navigator starts by displaying the Main Menu. This is the root
of the screen hierarchy, but you rarely will you need to return here
while using the program. Screens are also accessible from each
other to reduce the number of actions needed to initiate a function
or change a setting.
Most parts of the program are directly accessible from here by
using the buttons described below.
10 9
8
1
2
3 4
1. Displays current position
2. Displays current data and
time
3. Displays GPS status and
opens GPS data screen
4. Press to open SETTINGS
5. Press to exit the Navigator
6. Press to go to ABOUT screen
7
6
5
7. Press to open FIND &
GO menu
8. Press to open MAP
screen
9. Press to open COCKPIT
screen
10. Displays battery status
indicator
- 15 -
Page 16
6.2 About Screen
Tap About on the Main Menu screen to open this screen.
Information displayed here includes map licenses, the creators of
this Navigator and the legal aspects of using the program.
6.3 The Map
The most important and most frequently used screens of this
Navigator are the two screens with the map (Map screen and
Cockpit screen). They are similar in look and in possible controls but
are optimized for different uses. The map they display is common.
The elements of the map are described here. For the controls and
special functions of the two map screens see 6.5.
The current version of this Navigator is primarily intended for
land navigation. That is why maps in this Navigator look similar to
paper roadmaps (when using daytime colors and 2D map mode).
However, this Navigator provides much more than regular paper
maps can. The look and the contents can be changed.
- 16 -
Page 17
6.3.1 2D and 3D Map
Views
Besides the classical top down
view of the map (called 2D
mode), you have the possibility
to tilt the map to have a
perspective view (3D mode)
that gives a view similar to what
is seen through the windshield
with the possibility to see far
ahead.
It is easy to change between 2D
and 3D modes. You have two
options. You can use the Tilt up
and down button (6.5.3.) to tilt
the map seamlessly between
2D and all 3D angles, or you
can use the switch in the Quick
menu (6.7.2) to quickly switch
between the two modes.
NOTE:
You may nd that 2D mode is
more useful in North-up Map mode
when looking for a certain part of
the map or an object to select as
the destination. On the other hand,
3D mode in Track-up Cockpit
mode with Smart Zoom makes
navigation very comfortable. The
description of these modes will
come later in this manual.
NOTE:
3D view is only useful for
navigation. As you zoom out, the
view angle will automatically be
raised. Finally 2D view will be
reached. When you zoom back in,
3D view will gradually return.
NOTE:
Using the Advanced settings, you
can force Map mode to always
start in 2D North-up view and/or
Cockpit mode to always start in
3D Track-up view (7.6.1.2). You
can still rotate and tilt the maps in
either mode, but the next time you
enter this screen, the preset look
will reappear.
- 17 -
Page 18
6.3.2 Zoom Levels
This Navigator uses high
quality vector maps that let you
see the map at various zoom
levels, always with optimized
content (the density of the map
details can be independently
set for Map and Cockpit
screens in Map settings (7.2)).
Street names and other text
objects are always displayed
with the same font size, never
upside down, and you only see
as many streets and objects as
needed to nd your way around
the map. Zoom in and out to
see how the map changes in
either the 2D or 3D view.
Changing the scale of the map
is very easy. You can drag and
stretch the scale (6.5.6) at the
bottom of the Map screen,
or use the semi-transparent
screen icons (6.5.2) on both
Map and Cockpit screens.
NOTE:
If you need to zoom out briey to
locate your position on the map,
use the Overview mode instead
of zooming out and back in. The
Overview mode is a 2D Northup view that can be started by
tapping the compass button on
the right (see 6.5.8).
NOTE :
This Navigator has a special Smart
Zoom function for navigation that
automatically rotates, scales and
tilts the map in 3D map mode to
always give you the optimal view
in your current situation. When
approaching a turn it will zoom
in and raise the view angle to
let you easily recognize your
maneuver at the next junction. If
the next turn is at a distance, it
will zoom out and lower the view
angle to at in order to let you
see the road in front of you.
- 18 -
Page 19
6.3.3 Day and Night Color
Schemes
The different color schemes let
you adjust this Navigator to the
brightness of the environment.
Use the day and night color
schemes according. Daylight
colors are similar to paper
roadmaps, while the night color
schemes use dark tints for large
objects to keep the average
brightness of the screen low,
with carefully selected colors to
still keep you informed about all
the necessary information on
the screen.
You can change between day
and night views manually in the
Quick Menu (6.7.2.3) or let this
Navigator do it automatically
(7.1.3) for you.
NOTE:
The automatic day/night mode
is based upon the current date
and GPS position by which this
Navigator calculates the exact
sunrise and sunset times on the
particular day at the particular
location. Using that information
this Navigator can automatically
switch between the color schemes
a few minutes before sunrise,
when the sky has already turned
bright, and a few minutes after
sunset before it gets dark.
TIP :
There are several day and night
color schemes included with this
Navigator. To select the one that
suits your needs the best, make
your selection in Settings (7.2.1).
To further enhance the effect of
the night color scheme, you can
instruct this Navigator to decrease
the display backlight when the
night colors are used. Set the
desired backlight levels for both
day and night modes (7.6.2).
NOTE:
The colors mentioned and
screenshots included in this
manual refer to the default day
and night color schemes. They
may not look the same in the
schemes you have chosen.
- 19 -
Page 20
TIP :
If you use this Navigator after
sunrise or before sunset, look
for the sun in the sky in the map
background using a at 3D view. It
is displayed at its actual position to
give you another way to orientate
your direction.
6.3.4 Streets and Roads
The similarity of this Navigator
to paper roadmaps is also
convenient when it comes to
streets, the most important
elements of the map concerning
navigation. This Navigator uses
similar color codes to those you
are accustomed to, and the
width of the streets also refers
to their importance, so it will not
be difcult to tell a highway from
a small street.
Streets and roads have names
or numbers for identication.
Of course, this information can
be displayed on the map. This
Navigator uses two different
ways to show street labels. The
conventional way is the same as
a roadmap - it displays the name
of the street aligned with the
street. The alternative is a kind
of virtual signpost embedded
into the street itself.
You do not need to choose
between the two modes. This
Navigator will use the one best
for the current tilt and zoom
level. Zoom in to have only a
few streets on the map, and
start tilting up and down to see
how this Navigator switches
between the two modes in an
instant.
- 20 -
Page 21
NOTE:
The automatic switching is on
even when using Smart Zoom. At
rst you may nd it odd, but later
you will discover how it adjusts
the displayed information to the
current view on the map. It is
important, as the driver must be
able to read the map at a glance.
TIP:
If you do not want to be bothered
by street names during navigation,
turn them off in the Map Options
(7.2).
Major roads usually have
alternative names (numbering)
besides the primary name. You
can choose whether to display
these alternative names or not.
You can set this in Map Options
(7.2).
6.3.5 Other Objects
To help orientate you, the map
also contains objects that have
no other navigating function
other than to help you recognize
your location on the map.
These are surface-waters, large
buildings, forests, etc.
TIP:
These objects are normally
displayed using textured polygons
that are natural to the eye. You
may wish to switch the textured
display off (7.2.4) to free some
of the resources of your PNA
by replacing textures with plain
colored surfaces.
6.3.6 Current Position and
Lock-on-Road
When your GPS position is
available, a blue arrow (yellow
when using night colors) shows
your location on the map. The
direction of the arrow represents
your direction. The arrow is
sized and vertically rotated with
the zoom and tilt levels to always
look realistic.
- 21 -
Page 22
This Navigator has a builtin Lock-on-Road feature that
always puts the position arrow
on the road, on the axis of the
street in case of one-way streets,
or on the side of the road where
you drive on two-way roads.
The location received from the
GPS receiver is shown as a
blue dot on the map. This can
help you nd your location if the
GPS accuracy is poor, and the
Lock-on-Road system puts you
on the wrong street. It is also the
location saved in the track log
(6.7.2.6).
NOTE:
The Lock-on-Road feature can be
turned off in advanced settings
(7.6.4.5) for pedestrian use.
When switched off, the arrow is
displayed at the position reported
by the GPS receiver.
When the GPS position is
lost, the arrow turns grey, but
the journey continues on the
recommended route for a short
period of time with the speed
last detected before the GPS
position was lost. When the next
route event is reached, or after
40 seconds, the arrow stops,
and remains gray until GPS
reception returns. This way
short tunnels can be crossed
without losing the position.
6.3.7 Selected Map Point
(Cursor)
If you tap the map somewhere
or select a specic item in Find,
it will become the selected point
on the map, marked with a
small red dot and permanently
radiating red circles to make it
conspicuous at all zoom levels,
even when it is in the background
of a 3D map view. You can use
this point as starting or ending
point of the route. You can
search for a POI near to it, mark
it with a drawing-pin, or save
- 22 -
Page 23
it as a POI. The cursor, when
visible, is also the reference
point for map scaling.
NOTE:
When your GPS position is
available, and Lock-to-Position
(6.5.4) is active, the cursor is the
current GPS position, the blue
arrow). When you select another
point by tapping the map, or using
the Find menu (8.3), the new
Cursor is shown on the display
with the red dot and the radiating
red circles.
6.3.8 Marked Map Points
(Pin)
The Cursor can be marked with
a pin. Pins are shown as being
stuck in the map. A pin is visible
at all zoom levels and remains
in its position until you unpin it,
or delete all pins in advanced
setting (7.6.5.3).
- 23 -
Page 24
This Navigator automatically
selects the color of the pin.
Different colors help you identify
a pin in the History list (8.3.2)
later. There they are shown
together with their address and
GPS coordinates.
TIP:
A quick way to tell the coordinates
of a location you found on the
map is to pin it, and then look
for the coordinates in the History
list (8.3.2). This way you also
save the coordinates with the pin
for later reference. If you do not
need the coordinates later, just
select the point and start Find
Coordinates (8.3.3).
6.3.9 Visible POIs (Points
of Interest)
This Navigator comes with
thousands of built-in POIs,
and you can create your own
POI database as well. Having
all of them displayed on the
map would make the map too
crowded. To avoid this, this
Navigator lets you select which
POIs to show and which ones
to hide (6.7.2.4) using their
categories and subcategories.
Icons on the map represent
POIs. For a built-in POI it is
the icon of the subcategory of
the actual POI. For points you
create, it is the icon you had
chosen when you created the
POI (it can be changed later).
These icons are large enough
to recognize the symbol, and
semi-transparent enough to not
cover the streets and junctions
behind them.
When the map is zoomed out,
the icons are not shown. As you
zoom in, small dots appear at
the locations of visible POIs.
Zooming in further makes the
full icons appear.
- 24 -
Page 25
If two points are too close to
each other so that icons overlap,
a multi-POI icon is shown
instead of individual ones. Zoom
in more to see them separately.
(Should the two POIs have the
same icon, this icon will be
displayed instead of the multiPOI icon.)
NOTE:
When navigating, POI icons can
be disabled together with street
names (7.2.3). If you still need
this information during your
journey, just drag the map to
disable Lock-to-Position (6.5.4).
This will restore street names
and POI icons immediately. Now
tap Follow to reactive Lock-toPosition.
TIP:
Tap the map on or near a POI
item to see the list of the names
of the nearest POIs in a popup
list, if it is enabled (6.7.2.5). To
see the details of a particular POI
in the list, tap the blue “i” icon
on the right. If you have too may
POIs nearby, this list may not be
complete. In the Cursor menu
(6.5.13) there is a button called
POI that leads you to the screen
of all nearby POI items. There
you can open them one by one to
see their details, and select any
of them as a route point.
- 25 -
Page 26
6.3.10 Elements of the
Active Route
This Navigator uses a multidestination routing system
in which you have a start
point (your current location if
GPS position is available), a
destination, the line of the active
leg of the route, and optionally
via points and inactive legs.
They are all shown on the map.
6.3.10.1 The Start Point, Via
Points and the Destination
These points are represented
by ags.
6.3.10.2 Animated Turn
Guidance
Animated arrows represent
all route events other than the
above-mentioned special points.
These arrows shown the direction
you need to travel to continue
your journey.
6.3.10.3 The Active Leg of
the Route
The active leg is the section
of the route you are currently
driving. If you have not added
any additional points, the whole
route will be the active leg. When
additionas points are present,
the active leg is the part leading
from your location to the next
additional point.
The active section is displayed
in light greenred. It is the most
conspicuous part of the map
even when in the background of
a 3D map view.
- 26 -
Page 27
The line of the route is displayed
on the driving side of the road for
two-way and on the axis in case
of one-way streets. When the
map is zoomed in and the line is
wide enough, small arrows show
the direction of the route. This
can be useful if you preview the
route before starting the journey
or when entering a complex
junction.
6.3.10.4 Inactive Legs of the
Route
Future sections of a route are
inactive. They are also shown on
the map with the same color but a
darker tint than the active one. An
inactive section becomes active
as soon as you reach its starting
begin to approach the point.
6.3.10.5 Roads in the
Route Excluded by Your
Preferences
Although you can choose or not
to include some road types in
Route parameter settings (7.4.4),
sometimes they are impossible to
avoid.
If so, this Navigator will display
those segments of the route with
an alternate color.
- 27 -
Page 28
6.4 GPS Data Screen
Tap the small satellite dish icon on the Main Menu, Map or Cockpit
screen to open this window.
The GPS Data screen is a collection of information received from
the GPS device and it also serves as the entry point to the following
screens:
• Time Sync
- 28 -
Page 29
6.4.1 GPS Data Displayed
The virtual sky on the left
represents the currently visible
part of the sky above you, with
your position as the center.
The satellites are shown at
their current positions. The
GPS receives data from the
green and grey satellites but
not from the red ones. Signals
from the grey satellites are only
received, while green ones are
used by the GPS to calculate
your current location. On the
right you can see the satellite
signal strength bars. The more
satellites your GPS tracks (the
green ones), the better your
calculated position will be.
Additional pieces of information
on this screen are: current
position in latitude/longitude
format, elevation, speed, date,
time and calculated accuracy.
6.4.2 GPS Connection
Indicator
In the middle to the left there is
a lamp similar to the ones used
for switches. This one has more
colors and represents more
values:
A fast blinking green
lamp means that there
is communication with
the GPS and data is
being received.
Other colors should not appear
with a built-in GPS. Should any
of these appear, this means a
faulty operation of your device.
NOTE :
Accuracy can be affected by
several factors the GPS cannot
take into account. Use this
accuracy information only as
estimation.
There are two icons on the left
to show the status of the GPS
connection and the quality of
reception.
6.4.3 GPS Data Quality
Indicator
In the top left corner there is a
satellite dish to show the quality
of the GPS position. Different
colors represent different
signals:
Red shows there is
no connection with
the GPS device. This
should never be the
case if your device has
a built-in GPS.
- 29 -
Page 30
Red means the GPS is
connected but no GPS
position is available.
Yellow means 2D
reception. A GPS position
has been acquired, and
the Navigator is ready
for navigation, but the
GPS is not using enough
satellites for calculating
the horizontal position.
Elevation data is not
provided, and the position
error may be signicant.
Green means 3D
reception. The GPS
receiver has enough
satellites to calculate
altitude. Position is
generally correct (yet it
can still be inaccurate due
to different environmental
factors). This Navigator is
ready for navigation.
6.4.4 Time
Synchronization
In the top right corner of the
screen you have another button
that leads to a new screen
where you can synchronize
the clock of your PNA to the
accurate time provided by the
connected GPS.
Turn on the Auto Correction
switch to let this Navigator
frequently check and correct the
PNA time with the GPS time.
Below that button you will
see the current values of the
GPS and the PNA clocks.
You can check here whether
any correction is needed. Tap
the button to manually
synchronize the time.
Below the PNA time you have
and controls to
manually correct the time with or
without a valid GPS time. It also
gives you the chance to correct
the time after synchronization if
your PNA does not support time
zones or daylight savings time.
- 30 -
Page 31
6.5 Screens with Map
Having explained the contents of the map, the description of the other
parts of the map screens follows. There are two map screens: the
Map screen and the Cockpit screen. The way they show the map
is the same but their look and controls are optimized for different
purposes.
The Map screen is to be used mainly without a GPS, to browse the
map, create user POI items, or to plan your route based on map
points. The Map screen is designed to give you the maximum map
area. This screen is usually used in 2D North-up mode (you can
set this Navigator so it always opens the Map screen like that - see
7.6.1.1).
The Cockpit screen is for driving purposes. Besides showing the
map, it contains some additional travel information if you are just
cruising (speed, current street you are driving on, speed limit for the
current street), and additional route data if you are navigating (e.g.
next street in your route, distance to travel, type of the next route
event). This screen is typically used in 3D Track-up mode (you can
make this Navigator always open the Cockpit screen like that - see
7.6.1.2).
There are several controls that function in a similar fashion on the two
screens. They are described on the following pages.
No. Display
1 (Cockpit only) Turn preview*
2
3
4
5
6 Indicates that Follow to GPS
position and heading is inactive
7 Selected map point (Cursor)
8 (Map only) Map scale
9 Menu
10 Map orientation and Overview
Control
Opens Route menu*
Zooms in (optional)
Zooms out (optional)
Tilts down (optional)
Tilts up (optional)
Re-enables Follow-to-Position/Smart
Zoom
Opens Popup Info and Cursor menu
Zooms in/out by dragging
Opens Menu (Find, Quick, Route, Main)
Switches North-up, Track-up and
Overview
- 31 -
Page 32
11 GPS position
Follow
simulation
Follow
1
2
3
4
5
9
7
10
11
12
13
14
6
15
8
1
18
17
20
9
23 19
10
11
12
13
14
15
6
1645
12 Battery status
13 Sound on or muted
14 Track Log recording or playback
15
16 (Cockpit only) Current street
17 (Cockpit only) Travel and Route
data**
18 (Cockpit only) Distance to next
turn***
19 (Cockpit only) Next street***
20 (Cockpit only) Approaching next
turn****
Opens GPS Data screen
Opens settings
Enables/disables muting
Opens Track Log screen
Opens Cursor menu
Opens Route Information screen
Opens Route Information screen
N/A
N/A
N/A
* On Map screen only when a route is
active
** Contents differ when a route is active
Map screen contents:
Cockpit screen contents:
*** Only appears when a route is active
**** Only appears when a route is active
and the next turn is near
- 32 -
Page 33
6.5.1 Turn Preview (No. 1)
On the Cockpit screen this eld
shows a graphic illustration of
the next maneuver. For example
when you approach a turn, an
arrow will show whether it is a
slight, normal or sharp turn.
When showing a roundabout,
the number of the exit is also
given in the picture.
This eld also serves as a
button. Tap it to get to the Route
menu (6.7.3). The Map screen
will show a button called Route
here if there is an active route.
This also leads to the Route
menu.
6.5.2 Zoom In and Out (No.
2 and 3)
These semi-transparent buttons
are only displayed if ‘Zoom &
Tilt’ is enabled in the Quick
menu (6.7.2.2).
Zoom out shows a larger part on
the map, while Zoom in shows a
smaller part of the map in more
detail.
The automatic Smart Zoom
function will do the necessary
zooming for you when navigating
(zooms out if the next turn is
at a distance to let you see
far ahead and zooms in when
approaching a turn to give you
a better view of the upcoming
maneuver). If you manually
change the zoom level, Smart
Zoom will no longer scale the
map by itself (automatic tilting
and rotating remains active).
You need to press Enter, or tap
the Follow button (6.5.4) to return
the zoom control to Smart Zoom.
You can also set this Navigator
to do this automatically after
a few seconds in case of the
Cockpit screen.
- 33 -
Page 34
6.5.3 Tilt Up and Down
(No. 4 and 5)
These semi-transparent buttons
are only displayed if ‘Zoom &
Tilt’ is enabled in the Quick
menu (6.7.2.2).
This function modies the
vertical viewing angle of the map
in 3D mode. You can change the
angle in a wide range starting
from a top down view (2D view
is seamlessly integrated) all the
way to a at view that lets you
see far ahead.
The automatic Smart Zoom
function will do the necessary
tilting for you when navigating
(gives a at view if the next turn
is at a distance to let you see far
ahead and raises the angle when
approaching a turn to give you
a better view of the upcoming
maneuver). If you manually
change the view angle, Smart
Zoom will no longer tilt the map
by itself (automatic zooming
and rotating remains active).
You need to tap the Follow
button (6.5.4) to return the tilt
control to Smart Zoom. You
can also set this Navigator to
do this automatically after a few
seconds.
6.5.4 Follow Mode - Lock to
GPS Position and Heading
(No. 6)
This semi-transparent icon is
displayed if the GPS position
is available, and the map has
been moved. It also appears
when you scale or tilt the map
while Smart Zoom is enabled.
Normally this Navigator
positions the map to keep the
GPS position visible somewhere
on the map (when North-up
orientation is selected), or
always at the bottom center
of the map (when Track-up
orientation is selected).
If you manually move the map,
it will freeze the map in the new
position. To return to the GPS
position, use this Follow button.
When Smart Zoom is enabled,
scaling or tilting the map also
stops the automatic zooming or
automatic tilting respectively. To
reactivate Smart Zoom, tap this
button.
TIP:
In Advanced settings you can
set a delay time after which this
Navigator pushes the Follow
- 34 -
Page 35
button for you on the cockpit
screen automatically. This can
be turned on for re-enabling
both Lock-to-Position and Smart
Zoom.
6.5.5 Cursor (No. 7)
As described in 6.3.7, if you tap
the map somewhere or select
one specic item in Find, it will
become the selected point on
the map, marked with a small
red dot and radiating red circles
to make it conspicuous. You
can use this point as starting
point, via point or destination for
your route. You can search for a
POI near it, mark it with a pin, or
save it as a POI.
NOTE:
When the GPS position is
available, the Follow button will
appear indicating that you have
disabled the Lock-to Position.
Tapping the Follow button will reenable the position and move the
cursor back to the current GPS
position. The same happens
when this Navigator restores
Lock-to-Position automatically,
if it is set in Advanced settings
(7.6.3.3).
6.5.6 Map Scale (No. 8)
The scale indicator is only
available on the Map screen. In
2D map view it represents the
scale of the map. In 3D view it
is the scale of the nearest part
of the map only.
You can use it in both 2D and
3D modes to scale the map.
Drag and pull it to the right to
zoom in, or left to zoom out.
6.5.7 Menu (No. 9)
This button opens the Menu
with the Find Engine, the Quick
menu, the Route menu and the
exit button that takes you to the
Main menu screen. The Menu
will be described in detail later
in 6.7.
6.5.8 Map Orientation and
Overview (No. 10)
You can view the map screens
in three different presentation
modes. This switch will cycle
through them in the following
order.
The usual map
orientation for navigation
is Track-up. It means
- 35 -
Page 36
this Navigator rotates the map
during navigation to always face
the direction of your travel. In
this mode an arrow (compass)
points towards North.
Tap this icon to switch
to North-up mode.
Now the map is xed
to keep facing north.
The icon changes to show the
new rotation mode.
Tap the icon again to enter
Overview mode. This mode
looks similar to the North-up
mode with one difference: the
zoom level in this mode has
a xed default to give you a
better look of where you are on
the map. You can change the
zoom level at any time. This
will not cause the Follow button
to appear, but when entering
Overview mode later, the default
zoom level will be restored.
The arrow representing your
position will be xed in the
middle of the screen. When
you move the map in Overview
mode, the Follow button will
appear, and when pushed, it
will move the map to have your
current position in the middle of
the map again.
You cannot rotate the map in
Overview mode. This mode is
strictly north up.
You can set this Navigator so
that it will switch to Overview
mode during navigation when
the next turn is far away. You
can specify this distance and the
xed zoom level of Overview in
Advanced setting (7.6.3.2).
An airplane icon
indicates Overview
mode.
Tap the icon again to return to
Track-up (automatic rotation)
mode.
6.5.9 GPS Position Quality
(No. 11)
Similarly to the icon found on
the GPS Data screen (6.4.3),
the map screens also inform
you about the GPS signal.
The black satellite dish
with the red exclamation
mark shows there is
no connection with the GPS
receiver. GPS navigation is not
possible. Devices with a built-in
GPS receiver are permanently
connected, so this icon may
not appear under normal
circumstances.
Red shows there is
a connection, but the
signal is too weak to
give a position. GPS navigation
is not possible.
- 36 -
Page 37
Black shows there is
a GPS position, and
navigation is possible.
When only one arc is
shown , the position is 2D (no
altitude available), and position
error may be signicant, yet this
Navigator is ready to navigate.
A black dish and two
arcs represent a 3D
GPS position. This
Navigator is ready to navigate.
6.5.10 Battery Status
(No.12)
The status of the battery is
also shown by this Navigator.
You can estimate the available
power reserve from the length
of the bar inside. Some
examples:
The thunderbolt in
the battery shows
the battery is being
charged.
Battery is not
charging, but it is at
full capacity.
Battery is not full,
but there is sufcient
reserve capacity.
When the inside of
the battery is red,
the battery needs
recharging.
6.5.11 Sound Muting
(No.13)
By tapping this button you can
quickly mute all sounds of the
PNA. This will not modify the
volume level and the enabled
or disabled status of the voice
guidance or the key sounds (all
to be set on the Sound Settings
screen: 7.3). It just mutes the
sound output. When muting is
enabled, the speaker icon is
crossed out.
Tap again to re-enable sounds.
NOTE:
Sound can be muted in Sound
setting (7.3), too. There you
have a Master switch that
works together with the switch
described above. There is also a
Master slider on that screen, that
you can use to fully turn down
the volume of the device. Setting
the volume low is different from
muting; therefore it will not show
up on the mute indicator.
- 37 -
Page 38
6.5.12 Track Log
Recording/Playback
Indicator (No.14)
When a track log is being
recorded, a red icon is displayed
on the map screens. This icon
also functions as a button
leading to the Track Log screen
(6.7.2.6) where you can stop
the recording or make the track
log visible on the map.
During track log playback a
green icon blinks. Tapping
this icon (in fact, tapping the
screen anywhere) stops the
simulation.
6.5.13 Cursor Menu (No.15)
The Cursor is the selected point
on the map (marked by a red dot
and radiating red circles around
it), or the current GPS position
when it is available and Followto-Position is enabled. When
you tap the screen to place the
Cursor, the Cursor menu pops
up automatically to give you the
list of possible functions you can
use the Cursor for. At the same
time Popup Info (street name,
house number and the list of
POIs nearby) appears near the
selected map point if Popup Info
is enabled in the Quick menu
(6.7.2.5).
If you do not use the Cursor
menu in a few seconds, it will
automatically vanish back to
the bottom of the screen, and
Popup Info disappears, too .
You can have them reappear
by reopening the Cursor menu
using the arrow in the bottom
right corner. When you open
the menu manually, it will stay
on until you close it or switch to
another screen.
TIP:
If you want to see the map around
the Cursor, close the Cursor
menu and reopen it. When this
menu is opened manually, the
map is always moved to have the
cursor in the center.
- 38 -
Page 39
The content of the Cursor menu
depends on the screen (Map or
Cockpit) and it is slightly different
if there is an active route already
planned. You have the following
options:
Start
Use the cursor as the departure
point for your route. This menu
point is available only in Map
mode and when there is no
active route. In Cockpit mode
the departure point of the route
is always the GPS position or if
it is not available, the last known
GPS position.
Route To
Use the Cursor as the destination
of your route. This button is to
start a new route. The previous
route (if it exists) will be deleted
and replaced. If a multi-point
route is active, this Navigator
will ask you whether you really
want to delete it together with all
its destination points.
Add Via
By inserting the selected map
point as a via, you instruct this
Navigator to cross this location
before the destination of the
route. This is the way to build
a multi-point route in reverse
order (when you wish to insert
a stopover ‘go to A but rst
get some fuel at B’ or want to
inuence the direction of the
route). This menu point works
only if a route is already active.
Remove Via
Removes the ‘via point” near
or at the Cursor. The route will
be recalculated immediately
excluding the deleted point. This
menu point replaces Add Via and
is available only if the Cursor is
near or at a via point.
Continue
Add a new destination to be
reached after the previous
destination. The new destination
replaces the old one, which is
now demoted to a via point.
This is the way to build your
multi-point route in straight order
(when you wish to visit several
destinations ‘go to A then to B’).
This menu point is available only
if a route is already active.
Pin
Push a colored pin in the map
at the selected point for later
use. This pin is visible at all
zoom levels and also appears in
- 39 -
Page 40
the History list together with its
exact position. This Navigator
automatically selects the color of
the pin.
Unpin
Remove the pin near or at the
Cursor. This menu point releases
the Pin and is available only if the
selected point is near or at a pin.
POI
Opens the list of POIs near the
selected point. These are the
POIs shown in the Popup Info
window. This menu point is only
available on the Map screen.
If you want to add a new POI
at the cursor, you can do so by
tapping Add POI in the bottom
left corner.
6.5.14 Current Street (No.
16)
This eld of the Cockpit screen
shows the name or number (as
available) of the current street or
road you are driving on.
TIP:
Some roads have an alternative
name (or number). This is normally
shown together with the primary
name in this eld. You can hide
these alternative names in Map
settings (7.2.2).
6.5.15 Travel and Route
data (No. 17)
The contents of these three
elds are different when cruising
(without an active route) or
navigating (following an active
route).
While cruising, the elds show
the present speed, the current
speed limit and the time of day.
While navigating a route, these
elds show the estimated time
needed to reach the destination
(ETE), the distance to
destination, and the estimated
arrival time at the destination
(ETA) by default.
You can choose what to display
in these three elds during
navigation, by going to Advanced
settings / Display Options
(7.6.1). See the following list for
your options. The only restriction
is that you cannot select a value
that already appears in another
eld. The possible eld contents
are :
• Distance to destination (default
value for the left eld)
• Time to destination (estimated
time in route, default value for
the middle eld)
• Distance to next via point
• Time to next via point
- 40 -
Page 41
• Time to next maneuver (next
route event)
• Speed
• Speed limit
• Arrival at next via point
• Arrival at destination (default
value for the right eld)
6.5.16 Distance to Next
Turn (No. 18)
This eld shows the distance
to go before reaching the next
route
event (turn, roundabout,
exit, etc.)
This eld is only displayed when
navigating a route.
6.5.17 Next Street / Next
City (No. 19)
This eld shows the road or
street that comes next in the
route itinerary.
If you are not yet in the town
where this next street is, this
Navigator will display the name
of the town instead of the name
of the road or street. A bullet
symbol will appear next to the
name of towns to help you tell
them apart from street names.
This eld is only displayed when
navigating a route.
6.5.18 Approaching Next
Turn (No. 20)
This bar is only visible when
approaching the next route
event. It appears on the screen
to visualize the distance when
you get closer than 300 meters
(1000 feet) to the next turn, and
it remains visible till you reach
the turn.
This eld is displayed only when
navigating a route.
- 41 -
Page 42
6.6 Route Information Screen
The Route Information screen has all the data and some of the
functions you need while you navigate. Some additional functions
can be found in the Route menu (6.7.3). Without an active route
one of the buttons is inactive and route data cannot be displayed.
As a reminder, you can open this
screen two ways: tapping the
Info button in the Route menu
(6.7.3.6), or tapping one of the
Route Data elds on the Cockpit
screen.
6.6.1 Route Data Displayed
(for Destination and Via
Points)
In the top section of the screen
you see information about the
current route. These elds are
continuously updated while this
screen is open.
When you open the screen, all
elds contain information on
reaching your nal destination.
Tap any of the elds to see data
on the via points starting from
the rst one through the nal
destination again.
- 42 -
Page 43
6.6.1.1 Route Line
The upper part of this screen
shows your planned route as
a horizontal line. The point
farthest to the left is the start
of the route and the point
farthest to the right is the nal
destination. You can see your
via point ags along the line,
spaced in proportion to their
distance.
The blue (yellow at night) arrow
representing your position will
travel from the left to the right,
giving you visual feedback of
your journey.
When you reach a via point,
it becomes the starting point
of the route, the past will be
deleted. The line with all the
other via points will be modied
instantly, and the arrow jumps
back to the left.
When this Navigator needs to
recalculate the route, the arrow
will not jump back to the left as
when reaching a via point, but
it may drift a bit as the length of
the new route may be different
from the previous one.
When the data corresponding
to the entire route is displayed
in the elds below, the line
is colored the same way as
the route line shown on the
map. When you see data that
belongs to a via point, the
route is colored only up to that
via point. The rest of the line
remains grey.
6.6.1.2 Distance Left
This value can also be displayed
in one of the Route data elds
on the Cockpit screen as
‘Distance to destination’. This is
the distance you need to travel
on the route before reaching
your nal destination.
If via points exist, tap and tap
again any of the elds to see
the distance to reach the rst,
second, etc. via point.
6.6.1.3 Method
This elds shows how the
route was calculated. It either
displays the ‘Route’ or the
‘Vehicle’ eld from the Route
parameter settings. If you
have chosen Car, Taxi, Bus or
Truck, the type of route (Fast,
Short or Economical) will be
displayed here; if you have
selected Emergency, Bicycle or
Pedestrian, this information will
be displayed here.
- 43 -
Page 44
6.6.1.4 Time Left
This is an estimated value that
can also be displayed in one
of the Route data elds on
the Cockpit screen as ‘Time
to destination’. It shows the
time needed to reach the nal
destination of the route based
on information available for
the remaining segments of the
route. The calculation cannot
take into account trafc jams
and other possible delays.
If via points exist, tap and tap
again any of the elds to see
the time needed to reach the
rst, second, etc. via point.
6.6.1.5 Estimated Arrival
This is an estimated value
that can also be displayed in
one of the Route data elds
on the Cockpit screen as ‘ETA
to destination’. It shows the
time needed to reach the nal
destination of the route based
on information available for
the remaining segments of the
route. The calculation cannot
take into account trafc jams
and other possible delays.
If via points exist, tap and tap
again any of the elds to see
the estimated arrival at the rst,
second, etc. via point.
6.6.1.6 Destination / Via Point
This eld shows the exact
address (or its coordinates if
the address is not available) of
the nal destination.
If a via point exists, tap and tap
again any of the elds to see
the address or coordinates of
the rst, second, etc. via point.
6.6.2 Warning Icons
The following 5 squares are
normally grey. Some of them turn
red and show a graphical symbol
in case warnings are attached to
the planned route. These are
warnings, so icons always show
information for the whole route,
even if the data elds display
values from your current position
to a via point only.
Click on any of the icons to show
its description.
A few samples of the available
icons:
This icon shows that
you need to pay toll
on the recommended
route.
This icon shows that
the route contains
highways. Tap the
icon to see the total
length of the highways
in the recommended
route.
- 44 -
Page 45
This icon shows that
toll roads are included
in the recommended
route.
This icon shows that
you need to board
a ferry along the
recommended route.
This icon shows that
you need to pay for
the ferry.
This icon is displayed
when this Navigator
could not plan a route
with all your road
type preferences
respected. Sometimes
it is impossible to nd a
suitable route near the
start or the destination.
This icon warns you
that this Navigator had
to recommend a route
that does not match
all your preferences
given at the Route
Parameters setting.
The recommended
route contains areas
only accessible to
pedestrians.
The recommended
route contains
unpaved roads.
The recommended
route contains roads
that require a permit or
permission to enter.
Information - any
other piece of relevant
but not categorized
information. Tap
the icon to see the
content.
Next page - displayed
when more than 5
warnings apply for the
recommended route.
6.6.3 Fit to Screen
Tap this button to display
an overview of the whole
recommended route. You will
jump to the Map screen with a
2D North-up view so that you can
check where the route takes you.
6.6.4 Parameters
This button opens the Route
parameter settings screen (7.4)
otherwise opened from the Route
menu (6.7.3).
- 45 -
Page 46
6.7 Menu
Tapping this button brings up a menu that allows you to access
some of the most frequently used functions of this Navigator.
6.7.1 Find Tab
This rst page of the Menu is Find
tab. It lets you select a destination
without rst having to locate it on
the map. The Find menu will be
described in detail later in 8.3.
6.7.2 Quick Tab
This provides quick access to
some congurable options.
6.7.2.1 3D Map
When the green light is on,
the map shows a perspective
view. When the green light is
off, the map is displayed in a
conventional top-down view.
This 2D view is also the end
of the tilt range, so tilting the
map up can also access it.
Conversely, 3D mode can be
switched on by tilting down in
2D mode. Map view modes are
described in 6.3.1.
NOTE:
When you reach 2D view by tilting
the map, Smart Zoom will tilt the
map as you press the Follow
button or it disappears after
the time out (set in Advanced
settings) expires. Use the 3D
Map toggle to permanently switch
to 2D view.
- 46 -
Page 47
If the map is zoomed out so that
the view angle is automatically
raised to a top down view, this
button will have no immediate
effect. When you zoom back
in, the view angle will or will not
change according to the new
state of the button.
6.7.2.2 Zoom & Tilt (Switch)
When the light is on, additional
transparent buttons (6.5.2 and
6.5.3) appear on the left side of
the map screens for zooming
and tilting
The Tilt buttons appear only at
higher zoom levels. If you zoom
out, they disappear.
6.7.2.3 Night Mode (Switch)
Turn on or off the night colors
to override the automatic color
scheme switching.
NOTE:
Using this option turns off the
Automatic Night Colors feature.
You need to re-enable it at the
General settings screen (7.1)
to have the colors change
automatically again.
6.7.2.4 Manage POI (Points
of Interest)
Here you can set all the
parameters of POIs that you
have created and the visibility
of the built-in POIs that come
with the map.
- 47 -
Page 48
Manage Built-In POI Visibility
The maps in this Navigator
come with a huge number of
POIs. Displaying all of them
would make the maps too
crowded. In order to avoid
that, you can decide which
POI groups to show and which
ones to hide on the map. This
Navigator has a multi-level
POI category system. You can
set the visibility of the top two
levels. All levels below that will
be shown or hidden according
to their respective category
(i.e. you can set the visibility
of Gas Stations in the Services
category, but all brands listed
under that will either be shown
or suppressed together).
their subcategories shown and
some others hidden. If you
highlight any of the POI groups
by tapping them, the button
in the bottom left corner will
become Show if the POI group
is hidden, or Hide if the group is
shown or partly shown.
TIP:
To make a partly shown group
fully shown, tap this button twice.
First you will hide the whole
group, and then you will have it
displayed with all its subgroups.
Tapping again the highlighted
POI group (except for My POI
- described later) opens the list
of subcategories of that group.
Here you cannot see partly
shown subgroups, as visibility
can only be set for the top two
levels of categories. Showing
and hiding a subgroup is done
the same way as for the main
groups.
Groups shown with a tick mark
are visible on the map; groups
without a tick mark are hidden,
while the ones shown with a
pale tick mark have some of
- 48 -
Page 49
Manage My POI
By highlighting then tapping
again the My POI switch on the
Manage POI main screen, you
can manage the POI groups and
items that you have created.
NOTE:
The group Unnamed only appears
if you have previously saved a
POI item without creating a new
POI group for it.
Tapping any of the group names
will open a list of POIs saved in
that group. This list is similar to
the list of POI results in Find.
The POIs are ordered based on
their distance from your current
position. If GPS position is not
available or you have disabled
Follow-to-Position by tapping
the map, the POIs will be
ordered by their distance from
the Cursor.
219 Midland Rd, Midland, WA 6055
5048 Lochinvar Rd, Memphis, TN 38116
238 E 8th St Long Beach, CA 90813
235 Park Ave S, New York, NY 10003
When the My POI Groups
are displayed, you have the
following options:
Show/Hide
Similarly to built-in POIs, you
have the possibility to show or
hide all POIs of the selected
category on the map. Groups
with a tick mark are displayed;
all other groups are hidden.
New
You can create a new My POI
group by tapping this button.
You need to select an icon, a
name, and the maximum zoom
level at which the POI is still
visible on the map (provided you
let the POI group be displayed
at all). You do not necessarily
need to create POI groups in
advance. You can do it while
saving a new POI.
Delete
You can delete any of your
previously saved My POI
- 49 -
Page 50
groups. This will delete all POIs
in that group. This Navigator will
ask you to conrm this action.
Edit
You can edit the attributes
(name, icon, visibility level) of
a previously created My POI
group.
display the list. If you tap Done
any time before this happens,
you receive the list of matches
on multiple pages.
ABC/Distance
By tapping this button you
can have the POIs sorted in
alphabetical order. Tapping
again will return to the distance
based order.
When you tap on any of your
POIs in the list, you will open a
new window with the details of
the selected POI.
Left / Right Arrows
If your groups ll several pages,
these buttons will let you browse
through them. The green eld
to the left of these buttons show
the current page number and
the number of pages.
When the list of My POIs
is displayed, you have the
following options:
Search
You can shorten the list of
matching POI items by ltering.
Just like in Find, enter a few
letters of the desired POI name.
When the number of matching
items can t in one page, this
Navigator will automatically
5048 Lochinvar Rd, Memphis, TN 38116
Here you have the following
options:
OK
If you tap this button, the map
screen returns with the selected
POI in the middle.
Edit
You can edit the attributes
(name, icon and group) of the
selected POI.
- 50 -
Page 51
Delete
You can delete any of your
previously saved POIs. This
Navigator will ask you to conrm
this action.
6.7.2.5 Popup Information
(Switch)
When this feature is enabled,
tapping the screen (activating
the Cursor, a radiating red dot)
on either of the map screens
also opens a pop-up box with
the selected street name,
house number and the name of
the nearby POIs, if any.
TIP:
Tapping one of the blue
Information icons behind the POI
names shows the details of the
appropriate POI item.
6.7.2.6 Manage Track Logs
Using this Navigator, it is also
possible to save the track logs
of your journeys. This screen
lets you manage all your track
logs. When it comes up, it
shows a list of all track logs
already saved.
The original name of a track
log is the date and time when it
was recorded. You can change
their name to something more
meaningful if you wish.
Each track log has a color,
shown to the left of its name
when the track log is visible
on the map. If the track is not
visible, an underscore character
is shown here. Tapping the line
of the highlighted track log will
toggle between showing and
hiding that log. The track log will
- 51 -
Page 52
be drawn on the map using the
color next to its name.
When a track log is being
recorded, a new line appears in
this list with an underscore, as
newly recorded track logs are
not shown in the map normally.
TIP:
If you wish to see the track
log currently being recorded,
highlight its line then tap again to
make it visible.
in the list, and GPS position
data will be saved until you
stop the recording or exit this
Navigator. A red icon (6.5.12) is
shown on the map screens to
let you know that a recording is
in progress. Tapping that icon
opens this Track Log screen.
Stop Recording
If recording is in progress, this
buttons stops it.
Info
This button opens a screen that
shows the track log details, and
lets you:
• Change the name of the track
log (Rename button),
• Change the color of the
track log (Color on the map
selector),
• Have it displayed on the map
(Fit to screen button)
In this screen you have the
following options:
Record
This will initiate track log
recording. A new line appears
Replay
Push this button to see a
simulation of the saved track
- 52 -
Page 53
log on the map. A green icon
(6.5.12) will appear on the
map screens to let you know
it is a simulation only.
6.7.3 Route Tab
This menu contains options to
manage different settings in the
program.
6.7.3.1 Recalculate
This menu point is only available
if an active route exists and
GPS position is present.
It brings up a menu with four
options. Using one of these
functions you can modify the
current route.
Recalculate
This function repeats the
route calculation based on the
previous setting. This possibility
is typically used when automatic
off-route recalculation is
disabled. However you may
consider using it when you
travel on a road parallel to that
recommended by the route.
In this case this Navigator
may not recalculate the route
for some time, but you can
force recalculation here. This
is also the button you will
most frequently use when the
window appears automatically,
provided that the manual route
recalculation is set in 7.1.5.
Drop Next Via Point / Delete
Route
You can modify the route to skip
the next via point if you decide
it is no longer needed. For
example, you may have added
the via point only to inuence
the route but you do not want
to actually reach it; or you have
- 53 -
Page 54
already almost reached it, and
this Navigator still keeps on
navigating towards that point.
When there are no via points
left (only the destination), the
name of this button turns to
Delete Route, and it cancels
the navigation.
Bypass
When you run into a trafc jam
or roadblock, you may want to
have this Navigator calculate a
route that departs the original
route as soon as it can. You
will need to select the minimum
distance along the original
route where your new route is
allowed to rejoin the original
route. Select the one you
feel appropriate for the trafc
difculty you face.
NOTE:
This function is to give you an
alternative for the next section
of the recommended route. To
change later parts of the route or
to avoid specic streets or turns,
use the Avoid function in Itinerary
instead (6.7.3.3).
When you use this feature, this
Navigator will keep on excluding
the same part of the map from
later routes until you manually
delete the route (6.7.3.2), or
restart this Navigator.
Cancel
This option returns directly
to the map screen without
recalculating the active route.
If you choose this option when
manual route recalculation is
congured in 7.1.5, navigation
stops and will be activated
again when you are back on
your original route.
6.7.3.2 Delete
Tap Delete to erase the active
route along with all its route
points (start, via points and
destination). If you later decide
that you need the same route
again, you will have to rebuild
it from scratch. This Navigator
will warn you before deleting
route data.
This function has a special role if
you have used the Avoid feature
during your journey. When you
arrive at your destination, the
route line disappears on the
- 54 -
Page 55
map and navigation stops. The
route is now practically deleted,
but if you plan a new route, the
roads, maneuvers and areas
excluded from your route will
also be avoided when planning
the new route. Tap Delete to
completely delete your previous
route together with its Avoid
restrictions.
NOTE :
When a POI item is used as a
route way point, deleting the
route will not delete the POI item
itself, just its role in the route.
6.7.3.3 Itinerary
This function opens the itinerary
(route event list) of the active
route. The Itinerary has three
different display modes and two
functions.
Display Modes
Display modes are different
only in the number of events
displayed in the list. List items
are always shown with all
information available including
pictograms of the needed action
and distance of the event from
the previous list item.
The literary is live and constantly
updated when navigating a
route. The list item coming next
in navigation is the highlighted
one until you highlight another
one by tapping it. After that, the
highlight remains on the item
you have selected.
Detailed Instructions
This is the list displayed when
Itinerary is opened. It is the
list of events in full detail. All
signicant junctions are shown
in the list, even ones to be
passed.
Instructions
By tapping the Mode button
once you will see the list of
events that need your attention,
i.e. the list of maneuvers during
the route. These are the events
shown in the Turn preview eld
and announced by the voice
instructions.
Route Summary
Tapping the Mode button
again will show an overview
of the route that contains
only the signicant roads and
intersections.
- 55 -
Page 56
Show
Tap this button to see a
highlighted list item on the map.
This will help you identify route
events in the list.
Avoid
Tap this button to show a list
of possibilities for modifying
the route. They let you
recalculate the route avoiding
the highlighted event and
sometimes also some of the
subsequent ones.
• Maneuver : This option
avoids the highlighted
action. For example if
you nd a turn too difcult
during rush hour trafc, this
Navigator will recalculate
the route excluding that
turn. If the next street is
important in the route, it is
likely that this Navigator will
replace the turn with several
easier ones to get to the
same street.
• Road : When you exclude
a road, this Navigator will
calculate a route that does
not use that road. It is useful
when you anticipate a trafc
jam in a street used in your
route, or a roadblock is
announced on the radio,
and you nd that road in
your itinerary.
• Distance:You can also nd
some distance buttons in
this list. They are similar to
the ones in the Bypass list
of the Recalculation menu
(6.7.3.1), but these can also
be used for distant parts of
the route.
NOTE :
You do not need to open the
Itinerary if you run into a roadblock
or trafc jam. To get an immediate
alternative route use the Bypass
function of Recalculate (6.7.3.1).
When you use this feature, this
Navigator will continue excluding
the same part of the map from
later routes until you manually
delete the route (6.7.3.2), or
restart this Navigator.
- 56 -
Page 57
6.7.3.4 Fly Over
This feature has no navigation
function; it merely provides a
quick view of the route. It will
present a simulation of the
route showing what you will see
later when navigating.
Lifelike Simulation
Tap the Fly Over button.
In this mode the simulation is
run at normal speed (using the
speed limit of the streets and
roads in the route), and voice
instructions are also played.
This mode is mainly useful for
demonstrating this Navigator, or
to learn the way it works before
your start your rst journey.
Tap anywhere on the screen to
stop the simulation.
6.7.3.5 Edit
Tap Edit to see the list of all
points used in the route. The rst
item in the list is the departure
point of the route without a
valid GPS position, the last
reached via point if you opened
the list during navigation, or
the point where this Navigator
most recently recalculated
the route. This means the list
is permanently updated, and
via points drop out during the
journey. The last item in the list
is your nal destination.
Use the arrows on the right to
browse through the list and
tap any line to highlight it.
You can perform the following
operations:
Add : You can add a new
route point (or a new nal
destination if the highlighted
item is the last one in the
list) after the selected
point. The Find menu
opens automatically to let
you search for an address,
POI, coordinates, one of
your favorite destinations,
or selects a point from the
History list. As soon as you
select any of these, this
Navigator returns to the Edit
screen and your selection
appears right under the
highlighted line.
• Delete : You can delete
the selected point from the
list. If the highlighted item
is the last one in the list,
the previous via point will
be promoted to be the nal
- 57 -
destination.
Page 58
• Optimize : You can optimize
the order in which you will
drive through the via points,
if there is no specic order
you would like to keep.
When tapping this button,
this Navigator reorders the
list instantly to save you time
and fuel. Optimization is for
via points only. Your starting
point and destination remain
in their positions, of course.
• UpandDown:Using these
buttons you can reorder the
list by moving the highlighted
item up or down in the list.
6.7.3.6 Info
This button opens the Route
Information screen described
in 6.6. This screen shows
information about the current
route and has a few additional
options to check and modify
your active route.
6.7.4 Main Button
The Main button at the bottom
right corner leads to the Main
menu screen described in 6.1.
- 58 -
Page 59
Settings
7
This Navigator provides several settings in order to let you
customize the functions of the program. The Settings screen can
be accessed directly from the Main menu screen (6.1) and from the
map screens by using the battery icon (6.5.10), while some of its
sub-screens are accessible from other parts of the program.
7.1 General Settings
These are the basic settings of this Navigator.
7.1.1 Safety Mode
Safety Mode will disable the
touch-screen above 10 km/h (6
mph) to keep your attention on
the road.
When you disable Safety Mode,
this Navigator will warn you.
- 59 -
Page 60
7.1.2 Set Favorite
Destinations
You can select two of your most
frequent destinations to be your
favorites (8.3.5). You can start
navigating to either of them by
only two taps on the screen.
The original names of these
points are Home and Work.
You can rename them and
specify their locations. To
determine the location you can
use the same Find menu options
(8.3) as for a route destination,
and depending on that choice
and the information available,
the location will be shown here
as a street address, a latitude/
longitude position, or both.
NOTE :
If you tap either of your favorite
destinations in the Find menu
(8.3.5) before dening it, this
Navigator will offer to take you to
this screen to set it up.
7.1.3 Automatic Night
Colors
Using the automatic night mode,
this Navigator will change
between the day and night color
schemes a few minutes before
sunrise and a few minutes after
sunset based on the time and
location information provided
by your GPS. Once you set a
permanent color scheme in
the Quick menu (6.7.2.3), this
automatic mode turns off. If you
need this Navigator to switch
between colors for you again,
you need to re-enable this
feature.
- 60 -
Page 61
7.1.4 Alerts
Tap this button to enable and
ne tune user alerts. A new
window opens with the options.
7.1.4.1 Warn When
Speeding
Maps may contain information
about the speed limits of the
road segments. This Navigator
is able to warn you if you exceed
the current limit. This information
may not be available for your
region (ask your local dealer) or
may not be fully correct for all
roads in the map. This setting
lets you decide whether you
want to receive the warnings or
not.
Speeding Tolerance
This Navigator will warn you
when you exceed the speed
limit by the amount specied
here. Select whether you want
to specify the tolerance as a
Fixed value (offset to the speed
limit) or as a Percentage.
The slider will change
depending on which mode you
have chosen.
Both positive and negative
values can be given in either
offset or percentage mode.
Alternative Speed Limit
If the speed limit of the current
road segment equals or is above
this limit, the speed warning will
use the alternative tolerance
instead of the previous one.
Move the slider to its rightmost
position to turn off the alternative
speed warning. Then the
settings of the upper slider will
determine the warning for all
roads.
- 61 -
Page 62
Alternative Speeding
Tolerance
If the speed limit of the current
road reaches the value set at
Alternative speed limit, this
setting will replace the basic
one set at the top of this screen.
The slider and the selector
works exactly like the basic
ones described in 7.1.4.1.
EXAMPLE :
To let you better understand how
this feature works, here is an
example. If you use the setting
on the left (portrait) screen
(example: +10 km/h --- 100 km/h
--- +5%), this Navigator will warn
you when driving at the following
speeds:
Speed limit Warning at
40 km/h 50 km/h (=40km/h+10km/h)
60 km/h 70 km/h (=60km/h+10km/h)
90 km/h 100km/h (=40km/h+10km/h)
100 km/h 105km/h (=100km/h+5%)
120 km/h 126km/h (=120km/h+5%)
160 km/h 168km/h (=160km/h+5%)
7.1.5 Route Recalculation
Once a route is planned, this
setting will tell this Navigator
what to do when you deviate
from that route.
7.1.5.1 Automatic
The route will be recalculated
automatically a few seconds
after you go astray.
- 62 -
Page 63
7.1.5.2 Ask First
This Navigator can also ask
your preference each time you
leave the planned route. The
route will not be recalculated
until you make your choice from
the menu that automatically
appears.
Your options are:
• Recalculate:This Navigator
will recalculate the route
with the previous settings.
The result is the same as if
Automatic recalculation was
selected.
• DropNextViaPoint/Delete
Route : This Navigator will
remove the next via point
from the list and recalculate
the route without it. If you
have only one target left,
the label of the button will
be Delete Route, and it will
end navigation.
• Bypass : if you have
deviated from the original
route because of a trafc
jam or roadworks, you can
instruct this Navigator to
avoid the original route for a
specied distance.
• Cancel : you can exit
without recalculating the
route. Navigation stops and
will be activated again when
you nd your way back to
the original route.
7.1.5.3 Disabled
If you stick to the original
route, and you wish to get
back to it on your own, you can
disable recalculation. This way
guidance will stop until you
return to the recommended
route on your own.
- 63 -
Page 64
7.2 Map Settings
You can set a few parameters
determining the appearance
of the maps in this Navigator.
7.2.1 Day / Night Color
Prole
This Navigator comes with
different color schemes for
both day and night use. There
is always one selected daytime
scheme and one selected nighttime scheme. This Navigator
uses these when switching from
day to night and back.
Tap the appropriate button and
select a new scheme from the
list.
7.2.2 Alternative Road
Names
Some highways have an
international name or number
for foreign travelers. You can
decide whether to show only the
local name or both.
7.2.3 Show Street Labels
You can set whether or not to
see the names of the streets
and the POI icons on the map
when driving. Based on the
current zoom and tilt levels,
street names are displayed
either aligned with the street or
on signposts embedded into
the streets (6.3.4). If you switch
these signs on, it will be easier
to recognize your location on
the map. If you turn them off,
it will be easier to see the road
layout.
NOTE :
You can only disable street
names and POI icons if this
Navigator follows your position.
As soon as you move the map
and the Lock-to-Position (6.5.4)
is disabled, street names and
icons become visible again. Tap
Follow to re-enable Lock-toPosition and have the labels and
icons disappear again.
7.2.4 Textured Polygons
Enable textured polygons, and
have rivers, lakes, forests and
other large objects displayed in
a more realistic and attractive
way on the map.
Disabling it will lead to uniform
areas but better performance
for old PNA devices with a slow
processor. See 6.3.5.
- 64 -
Page 65
7.3 Sound Settings
Settings on this page determine the way this Navigator sounds.
NOTE :
The Mute function (6.5.11) accessible from the map screens override
the settings on this screen. When this Navigator is muted, all sounds
disappear. These settings will not be changed; only the output will be
muted temporarily.
7.3.1 Master Sound
Volume / Switch
The loudness of this Navigator
is independent of your PNA
settings. When you run this
Navigator, the position of this
fader determines the device
volume level. When you exit the
program, the device settings
return.
The left part of this control works
as a mute button. Tap to mute
all Navigator sounds.
This works in tandem with the
Mute button (6.5.11) on the map
screens. Switching one of them
will change the status of the
other.
7.3.2 Voice Guidance
Volume / Switch
The switch on the left can turn on
or mute this Navigator’s audible
guidance. When turned on, the
slider on the right will adjust the
loudness of voice prompts. In
its leftmost position the voice
guidance is suppressed; in its
rightmost position the master
volume applies.
- 65 -
Page 66
7.3.3 Key Sound Volume
/ Switch
The switch on the left can
turn the key sounds on or
off. Key sounds are audible
conrmations of either pressing
hardware buttons or tapping the
touch screen. When key sounds
are turned on, the slider on the
right will adjust their loudness.
In its leftmost position the key
sounds are suppressed; in
its rightmost position they are
played at the master volume
level.
NOTE :
The sound effects of this
Navigator are context
sensitive. They will be different
if, for example you open or
close a window, or you enable
or disable a setting. It will
even let you know if you have
entered enough letters of a
street name to have a short
list of matches on the screen.
7.3.4 Dynamic Volume
When driving at high speed,
the noise in the car may be
too loud to clearly understand
the voice guidance messages
and perceive the key sounds.
Using Dynamic Volume you
can instruct this Navigator
to increase the volume to its
highest level when your speed
exceeds a certain minimum and
macimum speed (determined
by the Master volume slider in
sound settings).
Tap the Dynamic volume button
to turn on the feature. This will
also open the screen where
you can set the minimum and
maximum speeds.
7.3.5 Attention Tone
If this is set to Disabled, the
voice guidance will sound
without a preceding attention
tone. Setting it to Single Tone
will initiate a single attention
tone before the instructions,
while Double Tone will use a
double tone.
- 66 -
Page 67
7.4 Route Parameter
Settings
This is a very important page.
Settings here determine how
routes will be calculated. This
screen is directly accessible
from the Route Information
screen (6.6).
7.4.1 Method
Use the handle to set the speed
of the route calculation. In the
leftmost position the route
may not be optimal but the
calculation will be very fast.
Sliding it to the right will result
in more accurate routing in an
increased amount of time.
NOTE :
Since this Navigator calculates
routes very quickly, the position
of this slide is only used for long
routes. Short routes are always
calculated to give you the optimal
result independent of the slider.
7.4.2 Route
Here you can choose from three
different route types.
7.4.2.1 Fast
Choosing Fast will result in the
quickest possible route, given
that you can travel at or near
the speed limits on all included
roads. This is usually preferred
for fast and normal cars.
7.4.2.2 Short
Choosing Short will result in a
route that has the smallest total
distance of all possible
between the given points. This is
usually preferred by pedestrians,
cyclists or slow vehicles.
7.4.2.3 Economical
This setting is a wise combination
of the previous two. Although
basically going for the fastest
solution, if there is another route
taking a bit more time but a lot
less distance compared to the
quickest one, this Navigator will
choose this one instead to save
fuel.
- 67 -
routes
Page 68
7.4.3 Vehicle
You can set the type of vehicle
you will use to navigate the
route. Based upon this setting,
some of the road types will be
excluded from the route (e.g.
motorways for pedestrians), or
some of the restrictions may
not be taken into account (e.g.
emergency vehicles have no
restrictions).
Furthermore, when Bus or
Truck is chosen, the program
assumes that high speeds
cannot be achieved, and this
information is taken into account
when calculating the route, the
estimated time enroute (ETE),
and the estimated time of arrival
(ETA).
Available values:
• Car
• Taxi
• Bus
• Truck
• Emergency
• Pedestrian
• Bicycle
7.4.4 Road Types to
Include / Exclude
To let the route t your needs
you can also set which road
types are to be considered
or excluded from the route if
possible.
NOTE :
Excluding a route is a preference.
It does not necessarily mean total
prohibition. If your destination
can only be accessed using
some of the excluded road types,
this Navigator will use them but
only as much as necessary. In
this case a warning icon will be
shown on the Route Information
screen (6.6), and the road not
matching your preference will be
displayed in an alternate color
on the map.
7.4.4.1 Unpaved Roads
Unpaved roads are excluded
by default, as they can be in a
bad condition and you usually
cannot reach the speed limit on
them.
7.4.4.2 Highways
When driving a slow car or
towing another vehicle, you may
prefer not to take highways.
7.4.4.3 Ferries
The accessibility of temporary
ferries is not necessarily
included in the map data.
Furthermore you may need to
pay fare, so you may consider
disabling them from the preset
enabled status.
- 68 -
Page 69
7.4.4.4 U-turns
Although displayed amongst
road types, this is a type of
action. Most drivers prefer to
replace them with a few normal
left and/or right turns in the next
few junctions, so it is disabled
by default.
Turning back on dual roadways
is not considered a u-turn.
7.4.4.5 Permit Needed
To use some roads or enter
some areas you may need a
special permit or permission
from the owners. These roads
are excluded from your routes
by default. Use this switch if
your vehicle is authorized to
enter.
NOTE :
If you are not totally against
u-turns, leave them on, and add a
certain penalty (equivalent extra
distance to travel) in Advanced
setting Route options (7.6.4).
Via points are handled as
stopovers with regards to u-turns.
It means disabling u-turns on this
page will avoid u-turns during the
entire route if possible, but when
reaching a via point, the following
part of the route may be planned
starting in the opposite direction.
7.4.4.6 Toll Roads
Toll roads are included in your
routes by default. If you wish
to travel more to avoid paying
a toll, disabling them will make
this Navigator plan the best toll
free route for you.
NOTE :
You have a few more ways
to inuence routing and route
recalculation in Advanced
Settings Route Options (7.6.4).
- 69 -
Page 70
7.5 Language and Navigators
Here you can set the languages, measurement Navigator, and date
and time formats used by this Navigator.
7.5.1 Program Language
This button displays the
current written language of
the program. By tapping the
button you can select from a
list of available languages.
This Navigator will have to be
restarted if you change this
setting. This Navigator will
ask for conrmation before it
restarts.
7.5.2 Voice Language
This button shows the current
language of the voice guidance.
By tapping the button you can
select from a list of available
languages and speakers. Tap
any of these to hear a sample
voice prompt. Tap OK when you
have selected the new spoken
language.
NOTE :
If English is selected, there are
two options available for the
voice language. One option
provides turn-by-turn driving
instructions, the second option
provides text-to-speech (TTS)
information, otherwise know as
spoken street names.
7.5.3 Navigators
You can set the distance
Navigators to be used by
the program. This Navigator
may not support all of the
listed Navigators in some
voice guidance languages.
If you select a measurement
Navigator that is not supported
by the chosen voice guidance
language, you will see a red
warning message under the
selector.
7.5.4 Set Date and Time
Format
You can set the date and
time format displayed by this
Navigator. Various international
formats are available.
- 70 -
Page 71
7.6 Advanced Settings
These screens let you set a large number of different advanced
settings and initiate some special functions. These settings and
functions are divided into groups.
Tap on any button to set the corresponding parameters. They all
open new windows where you can make your desired changes.
7.6.1 Display Options
These settings determine how
this Navigator displays different
content elements or how it
presents the screens.
7.6.1.1 2D in Map Mode (and
North-up Orientation)
The normal use of the Map
mode is to browse the map and
look for different places on it. It
is usually done in a top down
view having north towards the
top of the map. By default this
Navigator uses the same look
for the map in both Map and
Cockpit modes.
Use this switch to instruct this
Navigator to always open the
Map mode in 2D with North-up
orientation for map browsing
purposes.
NOTE :
You will still have the possibility
to rotate and tilt the map, but
the map will return to 2D mode
whenever Map mode is started.
- 71 -
Page 72
7.6.1.2 3D in Cockpit Mode
(and Track-up Orientation)
The normal use of Cockpit
mode is cruising or navigating,
when the road lying in front of
the driver is the most important
part of the map. It is usually
done in a 3D view with the
current direction towards the
top of the map. By default this
Navigator uses the same look
of the map in both Map and
Cockpit modes.
Use this switch to instruct this
Navigator to always open the
Cockpit mode in 3D with Trackup orientation (automatic map
rotation) for driving purposes.
NOTE :
You will still have the possibility
to switch the map to 2D view or
north-up orientation, but the map
will return to 3D mode with map
rotation whenever Cockpit mode
is started.
7.6.1.3 Zoom in After Find
When this switch is turned off,
this Navigator will center the
map to the location selected
in Find but will not change the
zoom level. If you turn this
switch on, this Navigator will
also zoom in to the selected
point.
The zoom level in this case
depends on the type of object
you have searched for. For
example in the case of a city
search, the zoom level will
show you the whole city or
at least a signicant part of it
around its center. Selecting
POI, an intersection or an exact
address will give you a closer
look with only a few streets on
the display.
7.6.1.4 Coordinate Display
Format
Positions are sometimes
displayed with their addresses,
and sometimes with their
coordinates. This setting lets
you choose between displaying
coordinates in degrees (dd.
dddddd); degrees and minutes
(dd mm.mmm); or degrees,
minutes and seconds (dd mm
ss.s).
NOTE :
The coordinate display mode is
independent from the coordinate
input in the Find menu. You can
use all three formats freely on the
coordinate input screen.
7.6.1.5 Cockpit Screen
Layout
The content is xed in Cruise
mode (when there is no active
route), but for Navigation mode
you can change the content
on this screen. The available
values are listed in 6.5.15.
- 72 -
Page 73
7.6.2 Backlight Settings
Here you can set how the
display backlight behaves when
using this Navigator.
These settings are independent
of the settings of the other
applications of PNA.
7.6.2.1 Power Management
At the top of the screen you
can set how the backlight will
behave when the screen has
not been touched for a while.
Backlight Always On
You can choose to have the
remain on.
Smart Power Save
You can also initiate this special
feature of this Navigator.
Smart power save will light
up the screen only when you
press or tap a button, or if this
Navigator has something to
show you. After a few seconds
the light level decreases, and
after aonther few seconds the
backlight turns off. This helps
you achieve a longer battery
life.
7.6.2.2 Brightness
You can set the backlight level
separately for both day and
night modes, thus enhancing
the effect of the night color
scheme.
The values are between 0
and 99, where zero means
there is no backlight at all, and
99 represents the maximum
backlight value.
7.6.3 Smart Zoom
Smart Zoom is more than just a
usual automatic zoom.
While Navigating a Route :
When approaching a turn, it will
zoom in and raise the view angle
to let you easily recognize your
maneuver at the next junction.
If the next turn is at a distance,
it will zoom out and lower the
view angle to be at in order to
let you see the road in front of
you, or it can even switch to an
Overview mode to let you follow
your position on the map.
While Cruising : If there is no
active route and you are just
driving, Smart Zoom will zoom
in if you drive slowly and zoom
out to the limit set here when
you drive at high speed.
- 73 -
Page 74
These automatic features
can be personalized on this
screen.
7.6.3.1 Smart Zoom Settings
You can set how close
Smart Zoom can zoom in
when approaching the next
turn (Zoom-in limit), and the
maximum zoom level to zoom
out when the next turn is further
away (Zoom-out limit). The
default values are set to be
optimal in most cases.
7.6.3.2 Enable Overview
Mode
You can congure how the
Overview mode is triggered when
the next turn is at a distance.
The Route event distance will
determine when this Navigator
switches to the Overview or back
to the Navigation view.
The Overview zoom level will
determine the xed zoom level
of the map in both automatic
and manually selected (by the
Map orientation icon -- see in
6.5.8) Overview modes. You can
change the zoom level manually
at any time (the Follow button will
not be displayed), but when you
enter the Overview mode again,
the zoom level will be reset to
this value.
You can also move the map in
Overview mode. Then the Follow
button will appear, and when
pushed, it will move the map to
have your current position in the
middle again.
NOTE :
When this automatic feature is
disabled, you can still enable
the Overview mode manually as
described in 6.5.8.
7.6.3.3 Restore Lock-toPosition and Smart Zoom
As already mentioned, you can
move, tilt and zoom the map
during navigation. In these
cases a Follow icon (6.5.4)
appears on the screen.
When you tilt or zoom the map,
that part of Smart Zoom is
automatically deactivated. The
map will still follow your position,
but will not change the view
parameter you have modied.
You can return to the full Smart
- 74 -
Page 75
Zoom mode by tapping the
Follow button.
If you move the map, all parts of
Smart Zoom become deactivated,
and the view freezes. Tapping
the Follow button makes this
Navigator follow your position
again (Lock-to-Position) and also
re-enables Smart Zoom.
You can make this Navigator
push the Follow button for you
automatically after a few seconds
of inactivity.
This functionality and the related
parameters below apply to the
Cockpit screen only. The Map
screen will wait for your action.
Restore Lock-to-Position
Turn this switch on if you want this
Navigator to return to your current
GPS position after you have
moved the map during navigation.
This is useful if you have moved
the map accidentally, or if you
have moved it to quickly check
something near your route.
After a certain timeout set below,
the Follow button disappears, and
the map immediately jumps back
to show your current position.
Restore Smart Zoom
Use this switch if you want this
Navigator to re-enable Smart
Zoom after zooming, tilting
or rotating the map during
navigation. This is useful if
you have changed the view
accidentally, or you modied it
to quickly check something near
your route.
After a certain timeout set below,
the Follow button disappears ,
then Smart Zoom changes the
view back for navigation. Unlike
with Restore Lock-to-Position,
the view changes smoothly.
NOTE :
Smart Zoom can only be re-
enabled when it is activated at the
top of this page. With Smart Zoom
turned off, the Follow button will
not appear, nor will the view return
to its previous state if you zoom or
tilt the map.
Delay Before Restoring
You can set the timeout for
both Restore Lock-to-Position
and Restore Smart Zoom here.
Shorter delays are best if you
tend to accidentally change the
map display, but you may prefer
a longer delay if you often look
for things around your position
while driving.
Remember to only look at the
display if it is absolutely safe to
do so.
NOTE :
If you push the Follow Button
before the automatic Lock comes
into effect, Smart Zoom and Lockto-Position will be re-enabled
instantly.
- 75 -
Page 76
7.6.4 Route Options
You can set the basic route
parameters on the Route
Parameter settings screen
described in (7.4). On this
screen you have more ways
to inuence route planning and
route recalculation.
7.6.4.1 Off-Route Sensitivity
and Recalculation Delay
Depending on the quality of
your GPS device, the GPS
antenna location in the car
and the environment you are
driving in, route recalculation
can behave differently. This
navigator may think you have
departed the proposed route
and perform a recalculation
even if you have not done so.
When the GPS reception is
poor (e.g. Driving in an urban
environment amongst many
tall buildings), occasional
wandering (called position
uctuation) of the calculated
GPS position is likely. Although
this Navigator employs a
sophisticated Follow-onRoad system that will mostly
suppress these position errors
by aligning your position to
the recommended route and
the road network of the map,
sometimes the errors are too
large to correct.
To reduce the effect of large
errors, you can increase the
recalculation tolerance two
ways.
Off-Route Sensitivity
This is a range of relative
values from 0 to 10, telling
this Navigator how far the
GPS position should be
from the recommended
route before the program
decides to recalculate. Lower
values make this Navigator
insensitive to position errors;
higher values will result in
quicker reactions.
Recalculation Delay
This is a setting that helps
suppress the effects of
position uctuation. With a few
seconds delay in recalculation
even large position jumps can
be tolerated without a need
for route recalculation.
- 76 -
Page 77
7.6.4.2 U-turn Penalty
You can ne-tune the way this
Navigator takes u-turns into
account when planning a route.
You can tell this Navigator how
much extra distance you would
travel to avoid a u-turn.
NOTE :
This value is taken into account
only if U-turns are enabled in
Route parameters (7.4.4.4).
7.6.4.3 Cross-Border
Planning
By default this Navigator
plans routes using the border
crossing points. However, if
you live near the border, you
can disable border crossing
with this switch to remain within
one country.
7.6.4.4 Carpool Lanes
Your can instruct this Navigator
to use carpool lanes when
planning routes.
seamlessly correcting small
GPS errors. For pedestrian
use you may consider
disabling Lock-on-Road to
make this Navigator always
show your exact position.
NOTE :
By turning off Lock-on-Road you
also turn off the GPS position
error searching. The position
shown on the map will be subject
to all position errors and position
uctuations.
7.6.5 User Data
Management
Everything that was saved
(pins, My POIs, Favorites, track
logs etc.) or modied (Settings,
History lists) since this Navigator
was manufactured is stored
in a user database located in
the RAM of the PNA device.
Here you have options to save,
restore or reset the database or
parts of it.
7.6.4.5 Keep Position on
Road (Lock-on-Road)
This Navigator is normally
used for vehicle navigation,
therefore Lock-on-Road
will display the position
arrow precisely over roads,
- 77 -
Page 78
7.6.5.1 Backup Data
You can make a safe copy of
the whole user database on the
memory card.
Tap this button to copy all user
data to the memory card. The
backup is always created with
the same le name; so backing
up data will always overwrite
previous backups.
TIP :
If you wish to keep more versions
of the user database, or you wish
to save one particular state (e.g.
saved POIs and track logs of your
holiday), look for the backup le
on the Memory card, rename it, or
save it to your PC.
If you move to another PNA,
before removing the card from the
old one, make a backup, remove
the card and insert it into the other
PNA. Let the automatic setup run,
then return to this Settings page,
and push the Restore Data button
as described in the next section.
This Navigator will then restart,
and all your previous POIs, track
logs, settings, city and nd history
lists will also appear on the new
PNA.
7.6.5.2 Restore Data
If you have accidentally deleted
things, or you have created
a number of temporary items
and you do not wish to delete
them one by one, you can tap
this button to restore the state
of this Navigator to the latest
backup.
By tapping this button you will
lose all of the changes made
since the time of the latest
backup. This Navigator will
warn you about this before
overwriting the current database
with the backup.
7.6.5.3 Remove Pins
Normally pins can be deleted
one by one. Since they are
shown at all zoom levels, and
you may end up having too
many of them, this button lets
you delete all of them together.
This Navigator will warn you
that you are about to lose all
your pins.
7.6.5.4 Clear Data
This button will delete all user
data. It is a reset to factory
settings. Tapping this button
means you lose all your saved
data and customized settings.
This Navigator will warn you
about this.
7.6.5.5 Reset Advanced
Settings
There are a multitude of
advanced settings in this
Navigator. Some changes may
cause this Navigator to behave
in an unsatisfying manner. Tap
this button to restore the default
settings.
- 78 -
Page 79
Find
8
One of the most frequently used functions of this Navigator is
selecting the destination. Once you have the destination, you can
start navigating. Getting to this point should be as fast as possible.
This Navigator provides you with a versatile search engine
designed to nd your chosen destination after only a few taps on
the screen.
NOTE :
If you select a location in any part of the Find system, you will normally
drop back to the map screen, where you will have several possible
actions (set as start, set as destination, add as via, continue route with,
mark with a pin, or add as a POI item). However, if you enter the Find
system using the Find & GO button, this Navigator will immediately put
you into Cockpit mode and start navigation.
8.1 Find & GO (Main
Menu)
As just mentioned, the fastest
way to nd your destination
and start navigating is to tap
Find & GO in the Main Menu
(6.1) This will put you on the
Find screen, and as soon as
you pick a destination, this
Navigator will immediately
show the Cockpit screen
and start navigation. This
means that if you plan your
route to one of your favorite
destinations, you only need
two taps to start navigating.
8.2 Selection by
Tapping the Map
It is also very easy to set your
destination using the map.
Just browse to your desired
destination on the map, tap it,
and the Cursor menu with the
possible actions will then open
automatically.
NOTE :
When appearing automatically,
the Cursor menu remains open
for a few seconds only. If you
decide not to choose any of the
actions, listed, the menu closes
automatically. When you open
it manually, it will remain until
you close it or switch to another
screen.
- 79 -
Page 80
TIP :
If you want the selected point
shown in the center of the map,
close and reopen the menu or wait
until it closes and open it again.
By opening the Cursor menu
manually, the map will be moved
to have the selected location in the
center.
8.3 Using the Find
Menu
The Find menu is accessible
by the Find & GO button at
the Main Menu (6.1) or by
the Menu buttons of the map
screens (6.5.7). The Find menu
gives you various possibilities
for selecting a location.
8.3.1 Find an Address,
Street, Intersection or City
Searching for a city, a street,
an intersection, or an exact
address can all be done in
the Find Address module. If
you know at least a part of the
address, this is the quickest
way to nd the location.
The following illustration shows
the structure of the address
search module. There are ve
levels (Country, State, City,
Street and Address). The list of
recent cities and states is the
entry point of the module. The
red rectangles are the exits.
You can complete your search
by selecting the center of a
city, the midpoint of a street, an
intersection of two roads, or an
exact address.
You enter the module at Level
3. From this point you can go
forward (down) to give the
name of the street, then the
house number or intersection,
or backward (up) to change the
city, state or country to search.
- 80 -
Page 81
8.3.1.1 Selecting the City,
State and Country to Search
In
The rst screen of the address
search module is the list of
recently used cities. The rst
line of the list is always the city
you are in or closest to.
Should the city you are looking
for appear on the list, just tap it
and you will immediately jump
to the Street Name Input screen
with the selected city name or
zipcode shown at the top of the
screen. If the desired city is not
displayed, use the arrows in the
bottom right corner to see more
of this list.
GPS position is available, and you
have not disabled Lock-to-Position
by moving the map.
If you nd that the list of recently
used cities contains cities you
will not visit in the near future,
you can choose to empty the list
by the Clear button in the bottom
left corner.
Selecting a New City to Search
In
If you are looking for a city or
town (or state) you cannot nd
on the list, tap Other City in
the top right corner. This will
take you to the city name or
zipcode input screen, where you
can select the desired city by
entering a few letters of its name
or some digits of its zipcode.
Select your choice from the list
of results automatically given by
the program.
TIP :
If during navigation you need to
know the name of the city or the
country you are currently in, just
start Find/Address and read the
rst line of the list. This function
leads to a reliable result only if
- 81 -
Page 82
You can accomplish this by
using an alphabetic input screen
(either an ABC- or QWERTY
type). You only need to enter the
rst few letters, as the program
only searches among the cities
that exit in the given state or
country. If the name of the city
is of more than one word, the
searched pattern can be any or
a combination of those. You can
search for multiple partial words
by inserting space characters in
the pattern. For example Key
West in Florida will be found if
you enter ‘Ke W’ or even ‘We K’
(any word order will do).
You do not need to enter
accents when searching for a
destination. Type only the base
letters (the letter most similar
to the accented one) and this
Navigator will search for all their
combinations in the database
(e.g. for the town ‘Déléagé you
only need to type ‘Deleage’,
and the rest is done by the
program).
As you start typing, this Navigator
will calculate the number of
cities matching your pattern(s).
This number is shown at the
right end of the input line. If all
the matching city names can
t on one screen, the sound
played when hitting the key will
be different, and this Navigator
will show you all the results in a
list. You can select the one you
are looking for by tapping the
appropriate list item.
NOTE :
When more than 300 matching
items (a list of more than 60
pages) exist for the entered
pattern(s), this Navigator stops
searching, and displays ‘>300’
at the right end of the input line.
Enter more letters to narrow the
list.
When the name of the city
contains a character that is
not available on the keyboard
(e.g. apostrophe or dash), this
Navigator considers it a space
that splits the word.
TIP:
If you have nished entering the
street name and the matching
names are still on more than
one page, just tap Done, and
select your desired city from
the list. Turn the pages with the
arrow buttons in the bottom right
corner.
TIP:
In case you are looking for a city
name that has more than one
word, you can reduce the list of
matches faster if you enter a few
letters from each word.
- 82 -
Page 83
Changing the State
Some of the maps contain state
information. If the city you are
looking for is in a different
state,
tap Other City then Change State
from the list of recently used
cities, then select the appropriate
state. Should you wish to search
for an address in the whole
country, just tap “Change state”
at the beginning of the list.
Once you have selected the city,
you can continue by entering the
street name.
1/11
When the state is selected, you
need to select a city by entering a
part of its name or zipcode, then
select from the list of available
matching items as described
before.
- 83 -
Page 84
8.3.1.2 Selecting a Street or
the Center of the City
Once the city is selected, you
can continue by specifying the
street you are looking for.
Note: As for the street input,
only available letters are active
when entering the rst word
of the street name . All other
letters are inactive and grey.
Selecting the Center of the
City
If you wish to navigate to the
city displayed in the top center
of the screen, just tap done
before entering any letters. The
search result will be the center
point of the city (where its name
is displayed on the map).
NOTE :
This point is not the geometrical
center but an arbitrarily selected
point chosen by the creators of the
map, usually the most important
intersection in a small town or
village, and for larger cities an
important intersection in the city
center.
Selecting a Street
If you are looking for an address
or an intersection within the
selected city (shown at the top
of the page), you need to rst
enter the street name you are
looking for.
TIP :
If you are looking for an
intersection, choose the street that
has a rare or unusual name rst.
This way you need to enter fewer
letters to get the list of results. You
may also choose the shorter of the
two streets rst. This way it will
be faster to choose the second
one from the list of crossing
streets after the rst street has
been selected.
You can search for both the type
and the name of a road. If you
have the same name appear as
Street, Avenue, Boulevard, Road,
Place and Court, you can get the
result faster by giving the rst
letter of this, too. For example
searching for ‘Pi A’ will result in
Pine Avenue skipping all Pine
- 84 -
Page 85
Streets and Pine Roads.
Should the name of the street be
a prex for several other street
names, just enter the whole
name, press done, and the exact
match will be the rst in the list.
This way you can easily nd even
very short street names.
As soon as you select a street,
you are automatically taken
to the House Number Input
screen.
Selecting a House Number
from Several Street
If you are uncertain which of
the resulting streets contain the
house number you are looking
for, tap Search In All, and
proceed to the House Number
Input screen without selecting
the street rst. Enter the house
number, tap Done, and a list
appears with only those streets,
where the given number exists.
To complete the search, pick
the appropriate address from
the list.
8.3.1.3 Selecting a House
Number or the Midpoint of
the Street
Once the country, the city and
the street name are selected,
you are asked to give the house
number using the numeric
keypad. The range of available
house numbers for the chosen
street is shown in the input eld
before you begin entering the
gures.
Enter the number, tap done, and
this Navigator will show you the
selected location on the map (or
will start navigating immediately
if you have selected Find and
GO at the Main menu).
NOTE
House numbers may not be
available on the map of your
region. Ask your local dealer for
details.
TIP:
If you do not know the house
number, just press done, and the
midpoint of the street will be used
as the selected location.
- 85 -
Page 86
8.3.1.4 How to Select an
Intersection Instead of a
House Number
If you do not know the house
number or it is easier to pinpoint
the location with an intersection,
press the Find intersection
button in the top right corner
and select the desired street
name from the list of available
intersections of the previously
selected street (displayed in the
top center of the screen). The
crossing of the two streets will
be the selected point.
8.3.2 Find in History
If you have used Find before,
or saved map points as POIs,
marked points with a pin, or
picked and used points of the
map before, they all appear in
the History list.
This list is ordered by the time
the points were last used. The
most recently used locations
are always at the beginning of
the list.
Just pick any of the recent
locations as your destination.
Here you have no possibility
to reorder the list or Search
it by name, but the Next and
Previous buttons let you browse
through the complete list to nd
your preferred point.
TIP:
If you will need a location later
but you do not want to save it as
POI, just mark it with a pin, and
remember its color to nd it easily
in the History list.
- 86 -
Page 87
8.3.3 Find Coordinate
This Navigator also lets you
enter your destination by map
coordinates. The coordinates
need to be in latitude/longitude
format and, based on the
WGS84 earth mode (the one
used by most GPS devices).
When you enter this page,
the coordinates of the current
GPS position (or the selected
map point (Cursor) if Follow-toPosition is inactive) are shown
at the top of the display.
The coordinates are always
shown in the format congured
in advanced settings Display
options (7.6.1.4), but you can
enter the coordinates in any of
the three formats. You can even
enter the latitude and longitude
in different formats.
Entering a latitude/longitude
pair is easy. The left eld
contains the latitude. It starts
with ‘N’ (North) or ‘S’ (South).
This tells this Navigator whether
the point is the Northern or the
Southern hemisphere. Use
the button to change the
hemisphere. Enter numbers for
the latitude. Use the decimal
point if the degrees, minutes or
seconds are not integers. Use
the / button (the label
depends on the current cursor
position inside the latitude) to
start entering minutes after
degrees or seconds after
minutes.
When nished, tap the
longitude on the right, and
enter it as you did latitude. This
time the hemisphere-changing
button tells this Navigator
whether the point is located
East or West from the meridian
crossing Greenwich, UK.
Once you have entered both
numbers, press done to make
the selection.
TIP:
The quickest way to tell the
coordinates of a point is to select it
by tapping on the map or by using
Find, and then come to this page
and read the coordinates.
If you need to reformat coordinates
to the format selected in this
Navigator at 7.6.1.4, enter the
- 87 -
Page 88
coordinates in the format you
have, press done to show it in he
map, then come back here to see
the same location in the chosen
coordinate display format.
8.3.4 Find a POI
You can select your destination
from the thousands of POIs
included with this Navigator
or from the ones you have
previously created. This screen
helps you nd the one you
are looking for. POI items are
categorized to let you locate
them more easily. On this screen
you can see the rst page of the
top level POI categories. There
are three levels total.
The search will be carried out
around a certain reference
point. Always look at the
current reference point shown
in the green eld above the POI
category buttons and conrm
that it matches what you want.
To change the reference, tap
the Change ref. button in the
top right corner.
Once you tap the Change ref.
button, you are presented with
these choices:
Address : You can specify
an address to be searched
around, or a city to search in.
The center of this city will be
used as the reference point.
History : The reference for
the search can be selected
from the History list.
Coordinate : You can specify
a latitude/longitude pair to be
the center of the search.
GPS Position : The search
will be carried out around
the current location given by
the GPS if it is available. If
no GPS position is available,
the last known GPS position
(grey arrow on the map) will
be used.
- 88 -
Page 89
Cursor : The search will
be carried out around the
previously selected map point.
Destination : The search
will be carried out around the
destination or your current
route.
The current selection is always
shown in the green eld at the
top of the page.
NOTE:
The default reference point for
POI search is the current GPS
position, if it is available, or the
Cursor, when there is no reliable
GPS position.
Once you have set the
reference point, you have the
following options on the Find
POI screen :
Search in POI Subgroups
: Highlight one of the POI
groups by tapping or using the
directions buttons, then press
Enter or tap it again to see the
list of subgroups. Using the
same action you can move
deeper into subgroups.
Search from all the POIs of
That Level : Tapping the Search
button will bring up a text input
screen to let you narrow the list
of POIs. If you tap Search in the
list of subgroups, you will only
search in the group you are
already in.
See all POIs of the Current
Group in a List : Tapping the
all button opens the list of all
points in the group or subgroup
you are already in. Use the Next
and Previous buttons to browse
through the list.
Search results are ordered by
their distance from the given
reference point (nearest rst).
NOTE:
In the case of POI items that you
have created, you can also see
the results in alphabetical order.
Push the button with the label ABC
that appears between Search and
the page number.
- 89 -
Page 90
Once the desired POI item is
selected, this Navigator will
show its details.
8.3.5 Find a Favorites
Location
If you have already set up your
favorite destinations in General
settings (7.1.2), you can select
either of them by simply tapping
the button with the name on it.
Using the Find and GO function
at the Main menu it is only two
taps to starts navigating to one
of your Favorites.
Tapping OK will return to the
map with the selected POI in the
center (or starts navigating to it
if Find and GO was selected).
Tapping the arrow in the top
left corner returns to the search
results.
TIP:
If you want to nd the nearest
POIs, or if you are close to one
of them but do not know exactly
where it is or what its name is,
tap the All button on the very rst
screen of POI search, and get a list
of the nearest POIs. Use the Next
button in the bottom right corner to
turn the page if you cannot see the
desired place on the rst page of
the list.
NOTE:
If you try to access a favorite
destination that you have not yet
set up, this Navigator will lead you
to the setup page.
- 90 -
Page 91
Troubleshooting Guide
9
Thank you again for purchasing our product. We hope you will enjoy every
minute of using it. However you may face difculties before you get really
accustomed to the Venturer GPS Navigation. In such cases, please refer to
this table of frequently encountered problematic situations.
I cannot nd the blue (yellow when using night colors) arrow that
would show my location. Navigation does not start.
Check the GPS status icon on the Main menu screen, any of the map
screens or the GPS Data screen. Either the connection to your GPS
receiver is broken, or the GPS cannot determine your position. Reconnect
your GPS, or move out of cover to get a position x.
The GPS is connected, sending valid position data, yet I cannot see
the blue (yellow when using night colors) arrow that would show my
position.
You should see a large semi-transparent ‘Follow’ icon on the screen. Tap
this to re-enable the Lock-to-Position feature that moves the map back to
your actual location.
The blue (yellow when using night colors) arrow shows my location,
but I cannot see the route (green or red line), and no voice instructions
are announced.
It is likely that you have no active route. Check the upper left corner of the
Cockpit screen if you can see the indication for the next turn or not. If this
eld is blank, you have no route planned, so you need to create one rst.
It is a common mistake to nd a destination, show it on the map, but forget
to tap the ‘Route To’ button in the Cursor menu to create the route. Be
sure to follow these steps, or always plan your routes with the ‘Find & GO’
button. This will ensure your route is calculated automatically as soon as
the destination has been selected.
I cannot see the Follow button on the screen, yet the map is not rotated
during driving.
Look for a small, red ‘N’ letter on the compass icon or an airplane icon. It
is likely that you had initiated the North-up map orientation or the Overview
mode unintentionally. Tap this icon to revert to Track-up mode with automatic
map rotation.
Creating a multi-point route I have tapped the ‘Route To’ button once
for each destination but only the last one appears in the list. All
previous points have disappeared.
- 91 -
Page 92
The ‘Route To’ button is for starting a new route only. For a single route you
tap this when the destination is selected. Multi-point routes can be created
after you have established a single route. Add points to the single route
by using the ‘Add Via’ and ‘Continue’ buttons. Applying ‘Route To’ again
will delete the whole route. In your case only single routes existed before,
so they were deleted without a warning message. If you already have a
multi-point route, Venturer GPS Navigation warns you before deleting the
whole route.
The speaker icon shows Venturer GPS Navigation is not muted yet I
hear no voice guidance.
The muting available from both map screens is just a quick silencer that
cancels the sound output. Voice guidance and key sounds need to be
enabled and volume must be set at the Sound Settings screen.
I enabled the speed warning as soon as I bought the product but I
havejustbeennedforspeedingbecauseVenturerGPSNavigation
failed to warn me.
For an accurate speed warning the actual speed limits of each street
and road must be present correctly on the map. This is a relatively new
feature of digital maps, so it may not be available in some countries, and
its accuracy still has much room for improvement (ask your local dealer for
the details in your region). This feature can help you in several cases but it
cannot be considered as serious speed control. That is why it can be turned
on and off separately from the reliable voice guidance.
- 92 -
Page 93
Glossary
10
The manual may contain many technical terms. Please look below for an
explanation if you are unfamiliar with some of them.
2D/3D GPS Reception:
The GPS receiver uses satellite signals to calculate its (your) position.
Depending on the current positions of the ever moving satellites in the sky,
and the objects in your environment, the signal that your GPS device receives
may be weaker or stronger. Your GPS needs strong signals from at least four
satellites to give a three dimensional position including elevation. If fewer
satellites are available, it may still be possible to calculate the position but the
accuracy will be lower and the GPS device will not calculate elevation. This is
called 2D reception. Venturer GPS Navigation shows the quality of reception
on the Main menu, the GPS Data screen and both map screens. Note that 2D
and 3D GPS receptions have nothing to do with the 2D and 3D display modes
of the map. That is a way of representing the map on the screen independently
from the GPS reception.
Accuracy:
The difference between your real position and the one given by the GPS device
is affected by several different factors. The GPS is capable of providing a guess
of its current error based on the number of satellites it can receive a signal
from, and their position in the sky. This information is shown in Venturer GPS
Navigation on the GPS Data screen. Use it as a general reference only. Note
that several other factors affect the real accuracy, some of which the GPS is
incapable of estimating (e.g. signal delay in the ionosphere, reecting objects
near the GPS device, etc.).
Active Route:
A route is an itinerary planned to reach your chosen destinations. A route
is active when it is used for navigation. Venturer GPS Navigation has only
one route at a time, and it is always active until you delete it, reach the nal
destination or exit Venturer GPS Navigation. When there is more than one
destination to reach, the route is cut into different legs (from one via point to
another). Only one of these legs can be active at one particular time. The rest
of them are unused and shown in a different color on the map.
Automatic Route Planning (Autorouting):
You only need to set up your destination, and based on its map, the software
will automatically gure out which roads you need to take, and the turns you
need to make to get there. Venturer GPS Navigation will let you select multiple
destinations, and customize some important routing parameters.
Automatic Route Recalculation:
If this function is enabled, Venturer GPS Navigation recalculates your route if
- 93 -
Page 94
you deviate from it. When you miss a turn or avoid a roadblock, Venturer GPS
Navigation waits for a few seconds to be sure you do not follow the route any
more (you can ne-tune it in Advanced settings), then recalculates the route
based upon your new position and direction.
Automatic Day / Night Colors:
Based on the time and position given by the GPS device, Venturer GPS
Navigation is able to calculate when the sun rises and sets at your current
location on this particular day. Using that information Venturer GPS Navigation
can change between the day and the night color schemes a few minutes before
sunrise and a few minutes after sunset. As additional information to help your
orientation, the sun is shown in the sky when you display the map in 3D mode
with a low viewing angle, and the sun is near the horizon.
Elevation:
When the GPS receiver can see at least four GPS satellites, it can determine
its current position in three dimensions. In this case the elevation is calculated
together with the latitude/longitude position. Note that some older GPS
Navigators may provide incorrect elevation data because they use a simple
ellipsoidal earth model rather than a database that contains local sea levels.
You should also be aware that the elevation value is generally less accurate
(by at least a factor of 2) than the horizontal position. See also 2D/3D GPS
Reception.
ETA (Estimated Time of Arrival):
A frequently used expression in navigation. It represents the time when you will
reach your destination based upon calculations using the remaining part of the
route and available information of the roads used. This estimation can only be
used as a general reference. It will not be able to take into account your future
speed or the trafc delays. In Venturer GPS Navigation this value is shown as
‘Estimated Arrival’ on the Route Information screen.
ETE (Estimated Time Enroute):
Another frequently used expression in navigation. It represents the time needed
to reach your destination based upon calculations using the remaining part of
the route and available information of the roads used. This estimation can be
used only as a general reference. It will not be able to take into account your
future speed or the trafc delays. In Venturer GPS Navigation this value is
shown as ‘Time left’ on the Route Information screen.
GPS:
Abbreviation for Global Positioning System. This system is operated by the
DoD (the Department of Defense of the Navigatores States Government). It
consists of 24 satellites orbiting Earth, and several ground stations to keep the
satellites in sync. To calculate your position, your GPS device uses the signals
- 94 -
Page 95
received from those GPS satellites that are currently visible at your location.
You can use this service free of charge.
Lock-on-Road:
This function of Venturer GPS Navigation will always keep the blue (yellow
when using night colors) arrow representing your actual position on the nearest
road. This automatic feature is necessary as the position given by the GPS
receiver is not perfectly accurate. Under normal circumstances Lock-on-Road
will eliminate the occasional position error. If the corridor of error is too large,
your position may be shown over a different street on the map. You can only
avoid that by using good quality GPS equipment positioned so it has a direct
view to as large a portion of the sky as possible. Normally Lock-on-Road is
always active in Venturer GPS Navigation when GPS position is available.
However for pedestrian use it can be permanently turned off in Advanced
settings.
Lock-to-Position:
When GPS position is available, Venturer GPS Navigation will automatically
keep moving the map to always have the blue (yellow when using night colors)
arrow, representing your actual position, on the screen. You can move the map
to lose this position. The Follow button will then appear on the screen and
tapping it will re-enable Lock-to-Position.
Map Orientation:
Venturer GPS Navigation is able to rotate the map for your convenience. If you
choose Track-up mode, the map will be rotated to look in the direction of your
heading. Selecting North-up, the map remains oriented to have North toward
the top. Use the left and right hardware buttons to turn your map in the direction
you wish. This will immediately turn off the automatic rotation. A small compass
in the top right section of the map screens will always show the current direction
of the map. Map orientation should not be mixed up with Screen orientation.
North-up:
A kind of map orientation having the map rotated to have North toward the top
of the screen. See also Track-up and Map Orientation.
POI:
Points of Interest. Exact map locations of important points saved in a database
together with their name, category and subcategories (e.g. Service/Fuel/
Autogas), address, phone and fax number, and other important information. Use
the versatile search system in Venturer GPS Navigation to nd the appropriate
POI near you, your destination or any other given location on the map. You can
also have your favorite places saved as ‘My POI’ in Venturer GPS Navigation.
- 95 -
Page 96
Track Log:
In Venturer GPS Navigation you have the possibility to record your journeys
using the position data your GPS provides in every second or every few
seconds (depending on your GPS settings). When you start the recording,
position data is saved in the database until you stop recording it. This set of
sequential GPS positions is called track log. Each set of consecutive positions
has a name (originally it is the time of recording but you can change it to any
name you like) and a color in which it can be displayed on the map. Later you
can replay the journey on the screen of the Venturer GPS Navigation device
as if it were happening again. This is good for demonstration purposes or for
analyzing your maneuvers during the trip.
Track-up:
A kind of map orientation when the map is rotated to always look in the direction
you are headed. See also North-up and Map Orientation.
Via Point:
Routes in Venturer GPS Navigation can have several (as many as you want)
different destinations to reach in a specic order. All these points except the
nal destination are called via points, as the route goes ‘via’ (through) them.
The destinations can be seen in the Route Information screen on the Route
line, and each via point is announced by the voice instructions as you approach
and when you reach it. Should your via point serve as a stopover, navigation
continues automatically as you depart. Navigation will resume even if you turn
off and on your device or restart Venturer GPS Navigation.
Zoom In and Out:
The Zoom function is used to change the scale of the map. Use Zoom In to
scale down the map to see less of it but in more detail, and use Zoom Out to
scale the map up to have a broader view of that part of the map with fewer
details.
- 96 -
Page 97
End User License Agreement
11
1. The Contracting Parties
1.1. Contracting parties to present Agreement are, on the one hand:
Nav N Go Kft (reg.no.: 03-09-111944) as Licensor and the legal user (as
dened in Section 2) of the object of present Agreement according to
Section 4, hereinafter referred to as User on the other hand (hereinafter
jointly referred to as Parties).
2. Conclusion of the Agreement
2.1. The Parties hereby acknowledge that present Agreement shall be
concluded by implicit conduct of the Parties, without a signature of the
Parties.
2.2. The User hereby acknowledges that following the lawful acquisition
of the software product constituting the object of present Agreement
(Section 4), any degree of use, installation to a computer or other
hardware, installation of such hardware into a vehicle, pressing of the
“Accept” button displayed by the software during installation or use
(hereinafter referred to as actions of use) shall be deemed as implicit
conduct resulting in the conclusion of the Agreement between the User
and the Licensor.
2.3. Present Agreement shall by no means entitle persons who unlawfully
acquire, use, install on a computer, install in a vehicle or utilize in any
manner whatsoever the software product.
2.4. The end user license agreement between the Parties shall be concluded
with terms set forth in present Agreement.
2.5. The time of conclusion of present Agreement is the time of executing the
rst action of use (commencement of use).
3. Applicable law
3.1. In issues not regulated by present Agreement the jurisdiction of the
Republic of Hungary shall be applicable, with specic reference to the
Act No. 4 of 1959 on the Civil Code (CC) and to Act No 76 of 1999 on
Copyrights (CA).
3.2. Present agreement is issued in English and in Hungarian. In case of
dispute the Hungarian text shall prevail.
4. The object of the Agreement
4.1. The object of present Agreement shall be the software product entitled
“Venturer” (hereinafter referred to as software product).
4.2. The software product shall include the operating computer program, its
complete documentation, and the map database belonging thereto.
4.3. Any form of display, storage, coding, including printed, electronic or
- 97 -
Page 98
graphic display, storage, source or object code of the software product,
or any other as yet indenable form of display, storage, or coding, or any
medium thereof shall be deemed as part of the software product.
4.4. Error corrections, additions, updates used by the User as dened in
Section 2 following the conclusion of present contract shall also be
deemed as part of the software product.
5. Owner of Copyrights
5.1. The Licensor – unless contractual or legal regulations state otherwise is the exclusive owner of all material copyrights vested in the software
product.
5.2. Copyrights extend to the whole software product and its parts separately
as well.
5.3. The owner(s) of the copyrights of the map database forming part of
the software product is (are) natural person(s) or corporate entity(es)
as listed in the appendix to present Agreement or in the „About/Map”
menu item of the operating computer program (hereinafter referred to
as Database Owner). Licensor hereby states that Licensor has obtained
sufcient usage and representation rights from the Database Owner in
order to utilize and give into further utilization the map database as set
forth in present Agreement.
5.4. In conclusion and execution of present Agreement the Database Owner
is represented by Licensor in relations to the User.
5.5. By concluding present Agreement, Licensor shall withhold all rights
vested in the software product, except for those that the User is entitled
to according to explicit legal regulations or that of present Agreement.
6. Rights of the User
6.1. The User is entitled to install the software product on one hardware
device (desktop, handheld, portable computer, navigation device) at a
time, and to run and use one copy thereof.
6.2. The User is entitled to make one security copy of the software product.
However, if the software product is operational after installation without
the use of the original media copy, then the original media copy is
deemed to be a security copy. In all other cases, the User is only entitled
to use the security copy if the original media copy of the software product
has become unsuitable for proper and legal use without any doubt, such
state thereof being supported by acceptable proof.
7. Limitations of Use
7.1. The User is not entitled
- 98 -
Page 99
7.1.1. to multiply the software product (to make a copy thereof);
7.1.2. to lease, rent, lend, distribute, transfer it to a third person with or without
a consideration;
7.1.3. to translate the software product (including translation (compilation) to
other programming languages);
7.1.4. to decompile the software product;
7.1.5. to modify, extend, transform the software product (in whole or in part),
to separate it into parts, compose it with other products, install it in other
products, utilize it in other products, not even with the aim of achieving a
co-operation with other products;
7.1.6. apart from using the computer program, to obtain information from the
map database included in the software product, to decompile the map
database, to use, copy, modify, extend, transform the map database in
whole or in part or the group of data stored therein, or to install it in other
products, utilize it in other products, not even with the aim of achieving a
co-operation with other products;
8. Non-Warranty, Limitation of Responsibility
8.1. Licensor hereby informs the User that although the greatest care was
taken in producing the software product, yet with respect to the essence
of the software product and the technical limitations, the Licensor does
not warrant for the software product being completely error free, and the
Licensor is not bound by any contractual obligation by which the software
product obtained by the User should be completely error free.
8.2. The Licensor does not warrant that the software product is suitable for
any purpose dened either by the Licensor or the User, and does not
warrant that the software product is capable of co-operating with any
other system, device or product (e.g. software or hardware).
8.3. The Licensor does not assume any responsibility for damages incurred
due to an error in the software product (including errors of the computer
program, the documentation and the map database).
8.4. The Licensor does not assume any responsibility for damages incurred
due to the software product not being applicable for any dened purpose,
or the error or lack of co-operation thereof with any other system, device
or product (e.g. software or hardware).
8.5. The Licensor shall hereby also draw the attention of the User with great
emphasis to the fact that while utilizing the software product in any form
of transportation, observing the trafc regulations and rules (e.g. use of
obligatory and/or reasonable and suitable security measures, proper
and generally expected care and attention in the given situation, and
- 99 -
Page 100
special care and attention required due to utilizing the software product)
is the exclusive responsibility of the User; the Licensor shall not assume
any responsibility for any damages occurred in relation to utilizing the
software product during transportation.
8.6. By concluding present Agreement the User shall especially acknowledge
the information stated in Section 8 above.
9. Sanctions
9.1. The Licensor hereby informs the User that according to regulations of the
CA, should the Licensor nd its rights to be breached, the Licensor may
9.1.1. claim the acknowledgement of such breach by court;
9.1.2. claim ceasing the breach and ordering the person under breach from
continuing such;
9.1.3. claim that the person under breach give proper compensation (even by
way of publicity, to the expense of the person under breach);
9.1.4. claim the return of the increase of assets due to the breach;
9.1.5. claim ceasing the breaching situation, the restitution of the state before
the breach, to the expense of the person in breach, and may claim the
destruction of instruments and materials used for the breach, and that of
the objects created by the breach;
9.1.6. claim damages.
9.2. The Licensor hereby also informs the User that the breach of copyrights
and related rights is a crime according to Act IV of 1978 on the Criminal
Code, which may draw as a sanction a sentence of two years in prison in
basic cases and up to eight years in prison in qualied cases.
9.3. For disputes arising from present Agreement the parties hereby agree
on the exclusive competence of - depending on value and title disputed
- either the Central Court of Budapest Districts or the Municipal Court of
Budapest.
- 100 -
811-930891W012
Printed in China
Loading...