Venstar ColorTouch T5800 Owner's Manual And Installation Instructions

HIGH

HIGH

Digital

Digital

RESIDENTIAL

THERMOSTAT

RESOLUTION

RESOLUTION

Thermostat

Thermostat

FULL

FULL

COLOR

COLOR

TOUCH

TOUCH

SCREEN

SCREEN

DISPLAY

DISPLAY

HEAT
COOL

OWNER’S

OWNER’S

MANUAL

MANUAL

AND

AND

INSTALLATION

INSTALLATION

INSTRUCTIONS

INSTRUCTIONS

T5800

HEAT
PUMP

CAUTION

Follow the Installation Instructions before proceeding.
Set the thermostat mode to “OFF” prior to changing
settings in setup or restoring Factory Defaults.

This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.

Thermostat T5800

Tested to Comply

c

with FCC Standards

C

F

4Z95

FOR HOME OR OFFICE USE

Page i

Glossary of Terms

Auto-Changeover: A mode in which the thermostat will turn on the
heating or cooling based on room temperature demand.

Cool Setpoint: The warmest temperature that the space should rise
to before cooling is turned on (without regard to deadband).

Deadband: The number of degrees allowed past setpoint, before
energizing heating or cooling.

Differential: The forced temperature difference between the heat set-
point and the cool setpoint.

Heat Setpoint: The coolest temperature that the space should drop
to before heating is turned on (without regard to deadband).

Icon: The word or symbol that appears on the thermostat display.

Mode: The current operating condition of the thermostat (i.e. Off,

Heat, Cool, Auto, Program On).
Non-Programmable Thermostat: A thermostat that does not have

the capability of running Time Period Programming.
Programmable Thermostat: A thermostat that has the capability of

running Time Period Programming.

Temperature Swing: Same as Deadband.

Time Period Programming: A program that allows the thermostat to

automatically adjust the heat setpoint and/or the cool setpoint based
on the time of the day. Same as Schedule.

Page ii

Table of Contents

Get to Know Your Thermostat

Home Screen

1
1

Menu Screens
Care and use of your thermostat

2

Quick Start

Selecting your desired temperature and mode

3

Using the Fan button

3

Setting the time

5

Setting the date

6

6

8

Daylight Savings setup

The Main Menu Buttons

Schedule

7

Time Period Schedule On/Off

8

View My Schedule
Edit My Schedule

8

Smart Fan

10

Smart Fan On/Off

11

Smart Fan Minimum Runtime

11

Start/Stop Times

11

Days to allow Smart Fan operation.

11

Screensaver

12

Screensaver On/Off

13

Screensaver Setup

13

Screensaver Preview

13

Alerts

14

View Current Alerts

15

Reset Alerts

15

Set/Edit Reminders

15

Service Information (Who To Call For Service)

15

Page iii

Table of Contents

Display

16

Active Brightness

17

Idle Brightness

17

Night Dimmer

17

Maintenance

18

Preferences

19

User Interface Themes

20

Custom Wallpaper

20

Heat/Cool Indicator

20

Backdrop On/Off

20

Sound Options

20

Vacation

21

Vacation Mode On/Off

22

Schedule

22

Modes & Setpoints

23

24

Security

Auto Screenlock

25

Setpoint Limits

25

Mode Restrictions

25

Information

26

Who To Call For Service

27

View Runtime Graphs

27

Settings

28

Thermostat Name

31

Available Modes

31

SD Card (Import and Export)

31

General Setup

31
31
32
32

32
33
33
33

33
33

Units (F or C)
Language
Smart Recovery ON/OFF
Simple Thermostat ON/OFF

Installation Settings

Heat & Cool Stages

Heat & Cool Stages
Compressor Stages
Aux Heat Stages

Page iv

Table of Contents

Installation Settings (continued)

33
35
36
36

36
36
36
36

36
36

36
37
37
37

38

38
38
39

40

40
41

42
42

43
44
45
46

49

50

56

Timers & Deadbands
Free Cooling
Heat Pump Settings

Heat Pump Lockout - Enabled/Disabled
Heat Pump Lockout Outdoor Temp

Aux Heat Lockout Enabled/Disabled
Aux Heat Lockout Temp
Dual Fuel Settings

Dual Fuel On/Off
Changeover With Outdoor Temp On/Off

Adjust Balance Point
Fan Off Delay
Calibrate Sensors
Test Outputs

Dealer Information
Reset To Factory Default Settings
Upgrade Firmware

Emergency Heat

ColorTouch Assistant

Installing the ColorTouch Assistant Software
Uploading Photos

Installation Instructions

Remove & Replace the Old Thermostat
Wire Connections
The Color Touch Thermostat Backplate
Explanation Of the Thermostat Dip Switches
Sample Wiring Diagrams

Troubleshooting

Index

Warranty

Page v

Get To Know Your Thermostat

Home Screen

Backlit Color Touchscreen Display

Date

&

Time

Fan

Buttons

Main Menu Screen

Menu

Back

Button

Buttons

Scrolling

Buttons

Page 1

Sub Menu Screen

Sub Menu

Buttons

Outdoor Temperature

With high & low temps for the day

(If optional sensor is installed)

Warmer

Button

SD Card

Slot

Cooler
Button

Menu

Button

Mode

Buttons

Scrolling

Indicates Options

Available

Buttons

Home

Button

Get To Know Your Thermostat

Care and Use of Your Thermostat

Pencils, pens and other sharp objects should never be used on your ColorTouch
thermostat; these may damage your touchscreen. Only use your finger tip to press
the touchscreen buttons.

Use a soft, damp cloth to clean the screen.

DO NOT USE ABRASIVE CLEANERS OR CLEANERS THAT CONTAIN
SOLVENTS. DO NOT SPRAY ANYTHING DIRECTLY ONTO THE
THERMOSTAT.

TM

Page 2

Quick Start

Temperature, Modes & Fan

Selecting Your Desired Temperature and Mode

COOLER

WARMER

MODE

or

or the MODE Icon

Press

The Heat or Cool Setpoint is the
temperature the room has to
reach before heating or cooling
will turn on.

(Without regard to deadband)

Press

HEAT will allow only heat operation.

COOL will allow only cool operation.

AUTO will allow both Heat and Cool operation.

OFF - heating and cooling systems are turned off.

AUTO-CHANGEOVER MODE - Pressing the WARMER or COOLER buttons in Auto

mode will adjust both the heat and cool setpoints simultaneously. To adjust heat and
cool setpoints individually, choose HEAT mode to adjust the heat setpoint and COOL
mode to adjust the cool setpoint, then return to AUTO mode.

HEAT OR COOL MODE - Pressing the WARMER or COOLER buttons in Heat or
Cool mode will adjust only the heat or cool setpoints.

Using the Fan Button

FAN

Press

FAN ON fan runs constantly even in OFF Mode.

FAN AUTO fan only runs with a heating or cooling demand.

or the FAN Icon

to adjust temperature

Fan

Page 3

Cool Setpoint

Heat Setpoint

Warmer

Button

Cooler
Button

Quick Start

Set Time & Date

Set Current Time

Use AM/PM - ON

Set Current Date

Daylight Savings Setup

Daylight Savings Time - OFF

Start Schedule

Starts On

Day

Month

Stop Schedule

Ends On

Day

Month

Set Time & Date

(2nd)

(Sun)

(March)

(1st)

(Sun)

(November)

Page 4

Quick Start

Setting the Time

MENU

Press

Press

Set Current Time

then

Set Time & Date

to scroll down.

(12:00 AM)

Set Time & Date

Press

Press

Press

Choose

For 12 hour AM/PM clock

For 24 hour clock

Press

hr +

and

hr -

BACK

when finished.

Use AM/PM - ON

Use AM/PM - OFF

BACK

when finished.

min +

min -

Page 5

to set the current time.

Quick Start

Set Time & Date

Setting the Date

Set Current Date

Press

Daylight Savings Setup

Turn Daylight Savings
Time on or off.

Adjust when Daylight
Savings Time begins.

Adjust when Daylight
Savings Time ends.

Press

after making a change
to a selection.

Press

or the Home button
when finished.

or

Press the day on the calendar

Su Mo Tu We Th Fr Sa

27 28 29 30 1 2 3

4 5 6 7 8 9 10

1211

13

18 19 20 21 22 23 24

1 2 3 4 5 6 7

BACK

BACK

7/8/2010

to set the current month and year.

17161514

31302928272625

Daylight Savings Time - OFF

Daylight Savings Time - ON

Start Schedule

Starts On

Day

Month

Stop Schedule

Ends On

Day

Month

Press

when finished.

Page 6

Press

(2nd)

(Sun)

(March)

(1st)

(Sun)

(November)

BACK

The Main Menu Buttons

The Main Menu Buttons

Schedule

Time Period Schedule - OFF

View My Schedule

Edit My Schedule

Information

Schedule

Page 7

The Main Menu Buttons

This thermostat features up to four programmable
time periods per 24 hour day: Morning, Day, Evening,
and Night. The start time for each time period is

Schedule

Press to turn Schedule On or Off

Time Period Schedule - OFF

adjustable. The stop time for each time period is
the start time for the next period.

Schedule

Time Period Schedule - ON

View My Schedule

Press a day of the week to view its settings. This may be repeated for each day.

Edit My Schedule

Press and select day(s) to program

Select individual day(s)

Select groups of day(s)

Then press NEXT

or

Page 8

Continued

The Main Menu Buttons

Schedule

Edit My Schedule

Press and select a Time Period (Morning, Day, Evening, or Night) to edit.

(Continued)

Next

Adjust Mode, Start Time, and Heat and Cool Setpoints to desired settings.
The Time Period may also be Enabled or Disabled. Un-check the Enabled
box for Time Periods you don’t want to use. Press DONE when finished.

Mode

TIP:

For a simpler schedule that only uses 2
time periods, un-check Enabled for Day
and Evening Time Periods.

Heat and Cool Setpoints

Enable/Disable

Start Time

When you are finished editing the
four time periods press

Review your program. Press SAVE to
keep your program. Press EDIT to
make further changes.

NEXT

Page 9

Done

Edit

Time Period

Save

The Main Menu Buttons

The Main Menu Buttons

Smart Fan

Who To Call For Service

Smart Fan - OFF

View Runtime Graphs

Smart Fan Min Runtime

Who To Call For Service

Start/Stop Times

View Runtime Graphs

Days To Run Fan

Information

Smart Fan

Page 10

The Main Menu Buttons

The fan may be programmed to turn on
automatically for a specified period

Smart Fan

Press to turn fan schedule on or off

Smart Fan - OFF

Smart Fan - ON

during the day.

Smart Fan

Smart Fan Min Runtime

Set the minimum number of minutes the fan will run from the top
of each hour. Set runtime to 60 minutes to be on continuously
from Start Time to Stop time. (5 - 60 mins.)

Start/Stop Times

Set when the Smart Fan schedule will start and stop. For example,
you may not want Smart Fan to run during sleeping hours.

Days To Run Fan

Choose which days of the week Smart Fan will run.

(7:00AM - 9:00PM)

(0m)

Page 11

The Main Menu Buttons

Screensaver

Who To Call For Service

Screensaver - OFF

View Runtime Graphs

Screensaver Setup

Screensaver Turn On Delay

Screensaver Type

Slideshow

Digital Clock

Analog Clock

Change Image After...

Use Theme Images - On

Show Clock - OFF

Home Screen Info - OFF

View Runtime GraphsScreensaver Preview

Screensaver

Page 12

The Main Menu Buttons

The Screensaver allows you to create custom
slideshows.

Screensaver

Screensaver

Screensaver - OFF

Screensaver - ON

Screensaver Setup

Screensaver Turn On Delay

How long after a button press for the Screensaver to appear.
1, 3, 5, or 30 minutes

Screensaver Type

Slideshow
Digital Clock
Analog Clock

Change Image After...

15, 30 seconds - 1, 5, or 10 minutes

Show Clock - OFF

Shows the time and date every 5 photos. Off or On

Home Screen Info - OFF

Shows the mode, setpoints, and temperature after every 10 photos. Off or On.

(5m)

(Slideshow )

Screensaver Preview

Press this button to preview your screensaver operation before
returning to the Home Screen.

After the preview, press anywhere on the screen to return to the sub menu.

Page 13

The Main Menu Buttons

Alerts

View Current Alerts

Reset Alerts

Reset Air Filter Alert

Reset UV Lamp Alert

Set/Edit Reminders

Service Call - OFF

Days Until Service Call

Air Filter Reminder - OFF

Set Max Filter Runtime

Set Max Filter Days

UV Lamp Reminder - OFF

Max UV Lamp Runtime

Service Information...

Alerts

(360 days)

(500 hrs)

(180 days)

(360 days)

Page 14

The Main Menu Buttons

The alerts let you know when your system
needs service.

Alerts

View Current Alerts

View and reset current
service alerts here.

Reset Alerts

Clear and reset current service alerts.

Set/Edit Reminders

Set service alert runtimes and turn reminders on or off.

Service Call Reminder - OFF

Days Until Service Call

Air Filter Reminder - OFF

Set Max Filter Runtime

Set Max Filter Days

UV Lamp Reminder - OFF

Set Max UV Lamp Runtime

Alerts will appear
on the bottom bar
of the Home Screen.

Press to view and
reset current alerts.

(360 days)

(500 hrs)

(180 days)

(360 days)

Dealer’s

Logo

here

Alerts

Service Information...

View your service company’s contact information.

Page 15

The Main Menu Buttons

Display

Active Brightness

Idle Brightness

Night Dimmer

Auto Night Dimmer - OFF

Set Idle Brightness

Set Dimmer Schedule

Maintenance

Screen Cleaning

Touch Calibration

Display

Page 16

The Main Menu Buttons

The display brightness options may be
adjusted in this menu.

Display

Display

Active Brightness

You may select how bright the backlight is while the thermostat is active. The
display is active for 3 minutes after last touch, it then goes Idle.

Idle Brightness

You may select how bright the backlight is while the thermostat is idle.

(80%)

(30%)

Night Dimmer

You may dim the brightness of the ColorTouch screen at night.

Auto Night Dimmer - OFF

The screen can be set to dim automatically at night. Dimming the
display can prolong the life of the backlight.

Set Idle Brightness

Set the screen brightness for the Night Dimmer. When Night Dimmer
is On, the display will go idle after 8 seconds after last touch.

Set Dimmer Schedule

Set the schedule for the Night Dimmer.

(20%)

Page 17

The Main Menu Buttons

Display

Maintenance

Maintenance allows you to clean and calibrate the ColorTouch Screen.

Screen Cleaning

Screen Cleaning Mode disables the touch feature for 15 seconds
so the screen may be cleaned without altering any settings.

Use a soft cloth without solvents or abrasive cleaners

Touch Calibration

Under normal circumstances, the ColorTouch touchscreen should not
need to be calibrated.

Touch the center of the targets as they appear on the screen.

Touch Screen Calibration

FINISH

Press when done.

When calibration is complete, the thermostat will automatically restart
and return to the Home Screen.

Page 18

The Main Menu Buttons

Preferences

User Interface Themes

Custom Wallpaper

Heat/Cool Indicator

Heat/Cool Indicator OFF

Taskbar red/white OFF

Room Temp red/blue OFF

Mode Status red/blue OFF

Backdrop OFF

Sound Options

Beep - OFF

Beep Sound

Show Outdoor Hi/Lo - OFF

Preferences

Page 19

The Main Menu Buttons

You may set the type of background that
appears on the thermostat Home Screen.

Preferences

Preferences

User Interface Themes

This thermostat has several high quality background themes to choose from.
NOTE: At 7 PM, the background will change to an evening scene and the
moon will replace the sun. At 7 AM it will return to a daytime scene.

(ocean)

Custom Wallpaper

You may choose your own background image by selecting a photo that you
have uploaded from an SD memory card.

Heat/Cool Indicator

You may choose an enhanced indicator of the current status of the HVAC
equipment.

Heat/Cool Indicator - ON/OFF
Taskbar Red/White - ON/OFF

Room Temp Red/Blue - ON/OFF
Mode Status Red/Blue - ON/OFF

Backdrop - OFF

The Backdrop makes numbers and words easier to read, and may be needed
on certain background images.

Sound Options

Beep - ON

Turn the beep sound on or off.

Beep Sound

Choose from different beep sounds.

(Beep 1)

Show Outdoor Hi/Lo - OFF

Choose to display or hide the high and low outdoor temperatures of the day on
the Home Screen.

Page 20

The Main Menu Buttons

Vacation

Vacation Mode - OFF

Schedule

Start Date

Start Time

Return Date

Return Time

Mode & Setpoints

Mode

OFF

Auto

Heat

Cool

Heat Setpoint

Cool Setpoint

Vacation

Page 21

The Main Menu Buttons

Vacation may use temporary, energy saving
settings without changing the regular

Vacation

Vacation Mode - OFF

Vacation Mode must be OFF to change Schedule, Mode
and Setpoint settings.

Schedule

Set your Vacation Schedule.

schedule.

Vacation

BACK

Tue Sep 07 2010

Start Date

Select the day Vacation Mode
will start.

Then press

BACK

Start Time

Select the time Vacation Mode
will start.

Then press

BACK

Page 22

(9:00 AM)

Continued

The Main Menu Buttons

Vacation

Schedule

Return Date

Select the day Vacation Mode
will end.

Then press

Return Time

Select the time Vacation Mode
will end.

Then press

BACK

BACK

BACK

Tue Sep 21 2010

(3:00 PM)

(Continued)

Modes & Setpoints

Select the desired Mode and setpoints to be used in Vacation Mode.

Mode

Heat Setpoint

Cool Setpoint

(Auto)

(50 )

(85 )

Vacation Mode - OFF

Vacation Mode - ON

Turn Vacation Mode ON. The Time Period Schedule must be ON to use
Vacation Mode. (See Schedule in the Main Menu)

Page 23

The Main Menu Buttons

Security

Auto Screenlock

Auto Screenlock - OFF

Set Passcode

Lock After...

Setpoint Limits

Setpoint Limits - OFF

Max Heat Setpoint

Min Cool Setpoint

Mode Restrictions

No Restrictions

No Modes Changes

Security

Page 24

The Main Menu Buttons

Security settings may be set to limit or
prevent changes to your thermostat.

Security

Auto Screenlock

Auto Screenlock - OFF

Auto Screenlock - ON

Security

NOTE: Code must be set before
Auto Screenlock can be
turned on.

Set Passcode

Use keypad to enter and confirm passcode.

When the thermostat is locked, the
bottom bar of the display will show:

Press UNLOCK then enter passcode to access thermostat settings.

Lock After...

Set the t the screen will automatically lock after the last button press. ime

(code not set )

(5 m)

Setpoint Limits

Limits how high or low heating and cooling may be adjusted.

Mode Restrictions

Limits which thermostat Modes are used.

Page 25

The Main Menu Buttons

Information

My Thermostat

View Runtime Graphs

Last 7 Days - Cooling

Last 7 Days - Heating

Delete Runtime Data

Who To Call For Service

Information

Page 26

The Main Menu Buttons

This button contains valuable service and
system runtime information.

Information

Information

My Thermostat

View your thermostat dip switch settings, equipment status, runtimes, and
other settings.

View Runtime Graphs

Track your system’s runtime/energy usage.

Last 7 Days - Cooling

Press the information
icon to learn more
about each graph

*NOTE: The runtime graphs are

Last 7 Days - Heating

Delete Runtime Data

Press to delete your current equipment runtime information.

updated at 12:00 AM each day.

Press anywhere on the screen
to return to the submenu.

Who To Call For Service

Your service company’s contact
information is displayed here.

Dealer’s

Logo
here

Page 27

The Main Menu Buttons

The Main Menu Buttons

Settings

Thermostat Name

Available Modes

All Modes Including Auto
Heat and Cool
Heat Only
Cool Only

SD Card

Import Settings from SD Card
Export Settings to SD Card

General Setup

Units

Fahrenheit

Celsius

Language

English
Spanish/Espanol
French/Francais

Smart Recovery - ON/OFF

Simple Thermostat - ON/OFF

Installation Settings

Information

Settings

(Continued next page)

Heat & Cool Stages

Heat & Cool Stages
Compressor Stages
Aux Heat Stages

Page 28

Availability depends on
Heat Pump
settings.

}

dip switch

The Main Menu Buttons

The Main Menu Buttons

Settings

Installation Settings

Timers & Deadbands

Cycles Per Hour
Min Heat/Cool Difference
Compressor Min Off Time
1st Stage Deadband
2nd Stage Deadband

2nd Stage Deadband
2nd Stage Timer
2nd Stage Turnoff Point

Deadband

3rd Stage Deadband

4th Stage Deadband

Free Cooling

Free Cooling - On/Off
Usable Outdoor Temp
Mechanical Cooling? - Yes/No

Setpoint

3rd Stage Deadband
3rd Stage Timer
3rd Stage Turnoff Point

Deadband
Setpoint

4th Stage Deadband
4th Stage Timer
4th Stage Turnoff Point

Deadband
Setpoint

Information

(Continued)

Settings

(Continued next page)

Page 29

The Main Menu Buttons

The Main Menu Buttons

Settings

Installation Settings

Heat Pump Settings

Heat Pump Lockout - Enabled/Disabled
HP Lockout Outdoor Temp
Aux Heat Lockout - Enabled/Disabled
Aux Heat Lockout Temp

Dual Fuel Settings

Dual Fuel - On/Off
Changeover With Outdoor - On/Off
Adjust Balance Point

Fan Off Delay

Calibrate Sensors

Thermostat
Outdoor Sensor

Test Outputs

Dealer Information

Dealer Name
Contact Name
Dealer Phone
Dealer Email
Dealer Website

Factory Defaults

Information

(Continued)

Settings

Delete Custom Images

Upgrade Firmware

Page 30

The Main Menu Buttons

Thermostat heating and cooling options are
found in this menu

Settings

Thermostat Name

Use keypad to name
your thermostat. The
name is displayed on
the Home Screen.

(Up to 14 characters)

Name appears here

Settings

Available Modes

Choose the desired modes the thermostat will use: Heat, Cool, Heat & Cool,
or Auto (All). For example, if you only have a heater, choose Heat, and only
Heat & Off modes will be available. This will simplify the operation for the user.

(all)

SD Card

Import and export files to and from the thermostat. See the ColorTouch
Assistant instructions for further details.

Import Settings from SD Card

Upload files from ColorTouch Assistant or another
thermostat.

Export Settings to SD Card

Export files from one thermostat and import them into others.

General Setup

Units

Fahrenheit (F)

Celsius (C)

(F)

Page 31

*NOTE: A 2GB SD card is
recommended. To import and
export files, the SD card must
contain the same version of the
firmware as the thermostat.

The Main Menu Buttons

Settings

General Setup

Language

English
Spanish/Espanol
French/Francais

Smart Recovery - OFF

Smart Recovery - ON

Smart Recovery turns on the heat before the Morning
start time to bring the room temperature to the Morning
setpoint at the start of the Morning time period. Please
allow 4-8 days for Smart Recovery time to adjust. When
used with a heat pump, electric strip heat will be disabled
while Smart Recovery is active.

Simple Thermostat - OFF

Simple Thermostat - ON

(en)

(Continued)

Turn on Simple Thermostat for the most basic user interface.

When Simple Thermostat is on, alerts will appear in the top bar of the
main screen. Press on the top yellow alert bar to view alerts.

Top Bar

Room

Temperature

Press

for

Heat

Press

to

turn

Off

Press

for

Cooling

Press

to turn

Fan

On or Auto

Warmer

Button

Single

Setpoint

Cooler

Button

Menu

Button

Page 32

The Main Menu Buttons

Installation Settings

Settings

(1h1c)

(1h1c)

(1h1c)

(6)

(2 )

(1h1c)

Only available when
dip switch is set for
Heat Pump operation.

}

Heat & Cool Stages

Heat & Cool Stages

Up to 2 Stages Cooling and 4 stages Heating.

Compressor Stages

Up to 2 compressors.

Aux Heat Stages

0 to 2 stages of Aux Heating.

Timers & Deadbands

Cycles Per Hour

At 6 cycles per hour, the HVAC unit will only be allowed to energize
once every 10 minutes. The Cycles Per Hour limit may be overridden
and reset by pressing the WARMER or COOLER buttons.
(2, 3, 4, 5, 6, No Limit)

Min Heat/Cool Difference

The minimum gap between Heat and Cool setpoints. (0 - 6 deg. F)

Compressor Min OFF Time

None, 1 minute, or 5 minutes.

(5m)

Page 33

The Main Menu Buttons

Settings

Installation Settings

(2 )

(2mins )

(Deadband )

(Continued)

(2 )

Timers & Deadbands

The Deadband is the number of degrees or minutes that the
thermostat waits before it initiates the stages of heating or cooling.

1st Stage Deadband Specifies the minimum temperature difference

between the room temperature and the desired setpoint before the first stage
of heating or cooling is allowed to turn on. For example, if the heat
setpoint is 68 and the 1st Stage deadband is set to 2 degrees, the room
temperature will need to drop to 66 degrees before the heat turns on.

1st Stage Deadband

(1 - 6 deg. F)

2nd Stage Deadband

2nd Stage Deadband

Number of degrees past 1st stage before 2nd stage turns on. (0 - 10 deg. F)

2nd Stage Timer

Number of minutes past 1st stage before 2nd stage turns on. (0 - 60 mins.)
(The 2nd stage deadband must also be met)

2nd Stage Turnoff Point

Deadband or Setpoint.

3rd Stage Deadband

4th Stage Deadband

(Continued)

3rd and 4th stage
deadband settings
are the same as
2nd stage.

Page 34

The Main Menu Buttons

Settings

Installation Settings

Free Cooling

Free Cooling is an energy saving way to boost the efficiency of your air conditioning
system by bringing in cool air from the outside. The installation of a Free Cooling
damper(s) and outdoor temperature sensor is required.

(Continued)

Free Cooling - DISABLED

Free Cooling - ENABLED

Turns on Free Cooling.

Usable Outdoor Temp

Free Cooling shuts off above this outdoor temperature. (40 - 80 degrees F)

Mechanical Cooling? - NO

(65 )

Mechanical Cooling? - YES

If you don’t have a compressor, set Mechanical Cooling to “NO”, Y1 will then be
used to control the Free Cooling Damper(s) and Y2 will be disabled. If set to
“YES”, mechanical (compressor) cooling will be controlled by the Y2 terminal.
(See page 48 for wiring diagram)

Mechanical air conditioning is turned on with a 2nd stage demand for cooling
and the Free Cooling, outdoor air damper is closed.

Supply Grilles

Return Grille

AirFlow

AirFlow

ReturnAir Grill

Barometric

Damper

AirFlow

FREE

Free Cooling

HVAC Unit

Supply

Coil

Furnace

Plenum

Air

Barometric

Vent to Attic

AirFlow

(To relieve building pressure)

Filter

Outdoor Air Grille

Damper

Damper1

Open
Return
Plenum

Damper2

Closed

Return

Damper

Outdoor

AirGrill

AirFlow

Free Cooling

Page 35

The Main Menu Buttons

Settings

Installation Settings

Heat Pump Settings

Heat Pump Lockout - DISABLED

Heat Pump Lockout - ENABLED

Turns on Heat Pump Lockout.

HP Lockout Outdoor Temp

Heat Pump will not run below this temp. (20 - 75 deg. F)

Aux Heat Lockout - DISABLED

Aux Heat Lockout - ENABLED

Turns on Aux Heat Lockout.

Aux Heat Lockout Temp

Aux Heat will not run above this temp. (20 - 75 deg. F) GAS/EL or HP dip
switch must be set for HP and GAS or ELEC dip switch must be set for ELEC.

Dual Fuel Settings

This feature is for heat pump applications only.

This will only appear if the GAS/EL or HP is set for HP and the GAS

dip switch

or ELEC is set for Gas.

When Dual Fuel is ON, an outdoor temperature or a demand for third stage

heat will be used to stop running the heat pump and switch to a fossil fuel
source of heat. NOTE: Once the change to fossil fuel is made, the heat
demand must finish with fossil fuel. Additional heat demands within 10 minutes
will also use fossil fuel, regardless of outdoor temperature or stage demand.

Dual Fuel - ON/OFF

Changeover With Outdoor - ON/OFF

Uses outdoor sensor for changeover.

Adjust Balance Point

Choose the temperature for changeover to fossil fuel. (5 - 60 deg. F)

Page 36

(Continued)

(65 )

(65 )

dip switch

(Only available
when dip switch
is set for Heat
Pump operation.)

The Main Menu Buttons

Settings

Installation Settings

Fan Off Delay

Runs the fan for a short time after Cooling or electric strip heat turns off
to increase system efficiency. (0 - 120 Secs.)

(Continued)

(0s)

Calibrate Sensors

Thermostat

The thermostat sensor may be calibrated -7 to +7 degrees F.

Outdoor Sensor

The outdoor sensor may be calibrated -7 to +7 degrees F.

(0 )

(0 )

Test Outputs

The installer or service technician can use this feature to test the
functions without any time delays of the thermostat and heating and
cooling equipment.

With a 1st stage cooling call, Y1 and G are active

Page 37

The Main Menu Buttons

Settings

Dealer Information

The Dealer may enter their company contact information for the
customer to use when they need service. This will appear in the
“Who To Call For Service” button is pressed in the Information Menu.

Press the buttons
below and use the
keyboard to enter
your information

Dealer’s

Logo
here

Dealer Name

Contact Name

Dealer Phone

Dealer Email

Dealer Website

Please use ColorTouch
Assistant to add Dealer’s
logo. (See Page 40)

Factory Defaults

Press to reset the thermostat back to the factory settings.

Delete Custom Images

Press to delete the custom photos you uploaded to the thermostat.

Upgrade Firmware

Press to upgrade the thermostat firmware. The SD Card must be in the thermostat
SD Card reader and contain the valid firmware. If an error message appears, confirm
with ColorTouch Assistant that firmware is up to date or simply try reinserting the SD
card.

Page 38

The Main Menu Buttons

The Emergency Heat function is only
available if your thermostat is set to

Emergency Heat

To initiate the Emergency Heat feature, Press the Emergency Heat button.
During Emergency Heat operation the thermostat will turn on the fan and
auxiliary stages of heat when there is a demand for heat. The 1st stage of
heating and all stages of cooling will be unavailable. To exit Emergency
Heat, press the Emergency Heat button.

control a Heat Pump.

Emergency Heat

Page 39

ColorTouch Assistant

ColorTouch Assistant may be downloaded at no charge at:

www.venstar.com/thermostats/colortouch/assistant/

Every time the user runs the ColorTouch Assistant software, it automatically
connects to Venstar’s ColorTouch Web site in the background and updates
the software and firmware (the operating system for ColorTouch) at no cost.

The ColorTouch Assistant allows you to use your computer to:

Upload photos for background
and slideshow images

Configure installation settings

Update thermostat firmware

Page 40

Program a time period schedule

Upload dealer and service contact
information and company logo

The ColorTouch Assistant

Uploading Photos and Settings to your thermostat

When you are finished adding and editing photos and settings,
click on Save to SD. When prompted, remove the SD card
from the SD card reader on your computer.

Save to SD

*NOTE: A 2GB SD card is
recommended.

At the thermostat:

Insert the SD card into the SD Card Slot.

MENU

Press

Next, press

then

Settings

SD Card

Slot

Press

Then, press

Select the items to import to your thermostat then press

Your thermostat will automatically save your new photos and settings.

SD Card

Import Settings from SD Card

NEXT

Page 41

Installation Instructions

Remove & Replace the Old Thermostat

To install the thermostat properly, please follow these step by
step instructions. If you are unsure about any of these steps,
call a qualified technician for assistance.

Assemble tools: Flat blade screwdriver, wire cutters and wire
strippers.

Make sure your Heater/Air Conditioner is working properly
before beginning installation of the thermostat.

Carefully unpack the thermostat. Save the screws, any brack­ets, and instructions.

Turn off the power to the Heating/Air Conditioning system at
the main fuse panel. Most residential systems have a separate
breaker for disconnecting power to the furnace.

Remove the cover of the old thermostat. If it does not come off
easily, check for screws.

Loosen the screws holding the thermostat base or subbase to the
wall and lift away.

Disconnect the wires from the old thermostat. Tape the ends
of the wires as you disconnect them, and mark them with the
letter of the terminal for easy reconnection to the new thermo­stat.

Keep the old thermostat for reference purposes, until your new
thermostat is functioning properly.

Page 42

Installation Instructions

Wire Connections

Wire Connections

If the terminal designations on your old thermostat
do not match those on the new thermostat, refer

to the chart below or the wiring diagrams
that follow.

Wire from the

old thermostat

terminal marked

G or F Fan G

Y1, Y or C

W1, W or H

C

O/B

W2

Y2 Y2

OUT -

OUT +

Function

Cooling Y1

Heating

PowerRh, R, M, Vr, A R

Common

Rev. Valve

2nd Stage Heat

2nd Stage Cooling

3rd Stage Heat

Outdoor Sensor

Outdoor Sensor

Install on the

new thermostat

connector marked

W1/O/B

C

W1/O/B*

W2

W3W3

OUTDOOR

OUTDOOR

* O/B is used if your system is a Heat Pump.

Page 43

Installation Instructions

The Color Touch Thermostat Backplate

NOTE:

The backplate does not fully cover a
full size vertical junction box. The
ACC-WPLWH ColorTouch Wallplate
or

a single-gang, horizontally mounted

would be needed for that

junction box
type of installation.

OUTDOOR

OUTDOOR

Y1Y2W1/O/B

W2

W3

CRG

To remove the thermostat backplate:

Using the Finger Pull Areas, pull the front
housing away from the backplate.

Look for these tabs to locate the pull areas

3rd stage heat circuit/2nd stage aux heat

W3

2nd stage heat circuit/1st stage aux heat

W2

1st stage heat circuit/reversing valve

W1/O/B

2nd stage compressor relay

Y2

1st stage compressor relay

Y1

Backplate

Pull out with thumbs in these areas

G
R

C

OUTDOOR

IMPORTANT: This thermostat requires both

R (24 VAC Return) and C (24 VAC Common) be
connected to the backplate terminals.

Page 44

Front Housing

Fan relay
24 VAC return

24 VAC common
Outdoor sensor
connections

Installation Instructions

Explanation of Thermostat Dip Switches

Dip switches are located on the back of the thermostat

GAS/EL

O

GAS

GAS/EL

HP HP

ON

1 2 3

O B

ON

1 2 3

ON

1 2 3

GAS

ELEC GAS ELEC

ON

GAS/EL

OR

OR

OR

HP

B

1 2 3

ELEC

This dip switch configures the thermostat to control a
conventional gas/electric system or a heat pump. If
your system is anything other than a heat pump,
leave this switch set for GAS/EL.*

ON

O

ON

ON

*For some commercial heat pumps, this switch may need to

1 2 3

be set for GAS/EL. Consult the commercial heat pump
literature.

When the GAS/EL or HP dip switch is configured for HP,
this dip switch (O or B) must be set to control the
appropriate reversing valve. If O is chosen, the W1/O/B
terminal will energize in cooling. If B is chosen, the

B

1 2 3

W1/O/B terminal will energize in heating.

*When GAS/EL or HP is set for GAS/EL:

This switch (GAS or ELEC) controls how the thermostat
will control the Fan (G) terminal in heating mode. When
GAS is chosen, the thermostat will not energize the
Fan (G) terminal in heating. When ELEC is chosen
the thermostat will energize the fan in heating.

1 2 3

*When GAS/EL or HP is set for HP:

This switch (GAS or ELEC) defines the Aux Heat type.
When GAS is chosen, the auxiliary heat will not be
allowed to run during heat pump operation. When
using a Dual Fuel system, set this switch for GAS.
When ELEC is chosen, up to two stages of auxiliary
strip heat will be allowed to run.

GAS/EL

O

ON

GASBELEC

HP

1 2 3

OUT+

OUTCR

G

Y1Y2W1-O-BW2W3

Page 45

Installation Instructions

Sample Wiring Diagrams with Dip Switch Positions

Conventional Heating and Cooling Systems

3 Wire, Heat Only

Residential & Commercial 1 Stage Heating
with no Fan.

GAS

O

24VAC Power
24VAC Common
1st Stage Heat

ON

B

1 2 3

ELEC

R
C
W1/O/B

GAS/EL HP

4 Wire, Cool Only

Residential & Commercial 1 Stage Cooling.

R
C
Y1
G

GAS/EL HP

GAS

O

24VAC Power
24VAC Common
1st Stage Cool
Fan

ON

B

1 2 3

ELEC

5 Wire, 1 Stage Cooling, 1 Stage Heat

Residential & Commercial 1 Stage Cooling,
with 1 stage Gas Heat.

GAS

O

24VAC Power
24VAC Common
1st Stage Heat
1st Stage Cool
Fan

ON

B

1 2 3

ELEC

8 Wire, 2 Stage Cooling, 3 Stage Heat

Residential & Commercial 2 Stage Cooling,
with 3 stage Gas Heat.

R
C
W1/O/B
W2
W3
Y1
Y2
G

GAS/EL HP

GAS

O

24VAC Power
24VAC Common
1st Stage Heat
2nd Stage Heat
3rd Stage Heat
1st Stage Cool
2nd Stage Cool
Fan

ON

R
C
W1/O/B
Y1
G

GAS/EL HP

Page 46

5 Wire, 1 Stage Cooling, 1 Stage Heat

Residential & Commercial 1 Stage Cooling,
with 1 stage Electric Heat.

GAS

O

24VAC Power
24VAC Common
1st Stage Heat
1st Stage Cool
Fan

HP

ON

ON

B

1 2 3

1 2 3

ELEC

1 2 3

B
ELEC

R
C
W1/O/B
Y1
G

GAS/EL

Installation Instructions

Sample Wiring Diagrams with Dip Switch Positions

Heat Pump Systems

5 Wire, 1 Stage Cooling, 1 Stage Heat

Residential & Commercial Heat Pump with
‘O’ Reversing Valve

R 24VAC Power
C 24VAC Common
W1/O/B Reversing Valve
Y1 1st Stage Compressor
(Cool or Heat)
G Fan

GAS/EL HP

GAS

ON

O

1 2 3

B
ELEC

6 Wire, 1 Stage Cooling, 2 Stage Heat

Residential & Commercial Heat Pump with
‘O’ Reversing Valve

R 24VAC Power
C 24VAC Common
W1/O/B Reversing Valve
Y1 1st Stage Compressor
(Cool or Heat)
W2 Aux Heat
G Fan

GAS/EL HP

GAS

ON

O

1 2 3

B

ELEC

7 Wire, 2 Stage Cooling, 3 Stage Heat

Residential & Commercial Heat Pump with
‘O’ Reversing Valve.

R 24VAC Power
C 24VAC Common
W1/O/B Reversing Valve
W2 3rd Stage Heat
Y1 1st Stage Compressor
(Cool or Heat)
Y2 2nd Stage Compressor
(Cool or Heat)
G Fan

GAS/EL HP

(Number of Compressor Stages set to 2)

GAS

ON

O

1 2 3

B

ELEC

Page 47

8 Wire, 2 Stage Cooling, 4 Stage Heat

Residential & Commercial Heat Pump with
‘O’ Reversing Valve.

R 24VAC Power
C 24VAC Common
W1/O/B Reversing Valve
W2 3rd Stage Heat
W3 4th Stage Heat
Y1 1st Stage Compressor
(Cool or Heat)
Y2 2nd Stage Compressor
(Cool or Heat)
G Fan

GAS/EL HP

(Number of Compressor Stages set to 2)

GAS

ON

O

1 2 3

B

ELEC

Installation Instructions

Sample Wiring Diagrams with Dip Switch Positions

Heat Pump Systems with Dual Fuel

7 Wire, 2 Stage Cooling, 3 Stage Heat

Residential & Commercial Heat Pump with
‘O’ Reversing Valve and Fossil Fuel furnace.

R 24VAC Power
C 24VAC Common
W1/O/B Reversing Valve
W2 3rd Stage Heat
(connected to furnace)
Y1 1st Stage Compressor
(Cool or Heat)
Y2 2nd Stage Compressor
(Cool or Heat)
G Fan

GAS/EL HP

Number of Compressor Stages
set to 2

(see Compressor Stages, pg. 33)

Dual Fuel set to On
(see Dual Fuel Settings, pg. 36)

GAS

ON

O

1 2 3

B
ELEC

Free Cooling

Free Cooling

Damper

10K Thermistor

Outdoor Sensor

ACC-TSEN

Free Cooling utilizes the Y1 terminal for the operation of 1st stage cooling. If
mechanical (compressor) cooling is also present, the mechanical cooling is
connected to the Y2 terminal in this instance.

Use 18-22 gauge thermostat wire.

Y1Y2W1/O/B

W2

W3

CRG

OUTDOOR

OUTDOOR

Free Cooling may be used with a Gas/Electric or Heat Pump system.

Outdoor Sensor: ACC-TSEN Temperature Sensor 10K ohm sensor at
77F/25C. Negative Temperature Coefficient.

Page 48

Troubleshooting

SYMPTOM: The thermostat touchscreen buttons are not responsive.
CAUSE: The touchscreen is out of calibration.
REMEDY: Remove the thermostat from the backplate. Push the

thermostat back onto the backplate, while keeping your finger
pressed firmly against the center of the touchscreen, until the
Calibration screen appears. Re-calibrate the Touchscreen.

SYMPTOM: The display is blank.
CAUSE: Lack of proper power.
REMEDY: Make sure the power is on to the furnace and that
you have 24vac between R & C.

SYMPTOM: The air conditioning does not attempt to turn on.
CAUSE: The cooling setpoint is set too high.
REMEDY: Lower the cooling setpoint or lower the cooling set-

point limit. See Setpoint Limits (page 25).

SYMPTOM: The heating does not attempt to turn on.
CAUSE: The heating setpoint is set too low.
REMEDY: Raise the heating setpoint or raise the heating set-

point limit. See Setpoint Limits (page 25).

SYMPTOM: When controlling a residential heat pump, and
asking for cooling, the heat comes on.

CAUSE: The thermostat reversing valve dip switch is set for “B”.
REMEDY: Set the reversing valve dip switch for “O”.

SYMPTOM: When calling for cooling, both the heat and cool

come on.
CAUSE: The thermostat equipment dip switch is configured
for “HP” and the HVAC unit is a Gas/Electric.

REMEDY: Set the equipment dip switch for “Gas”.

SYMPTOM: Air handler control board fuse blows when thermostat

is attached to backplate with power on, but does not blow until the
thermostat is placed onto the backplate.

CAUSE: The Outdoor sensor and/or sensor wiring is shorted.
REMEDY: Check/replace Outdoor sensor and/or sensor wiring.

Page 49

Index

A

Active Brightness, 17
Alerts, 14

view current, 15
reset, 15
set/edit reminders, 15

See also Runtime
Aux Heat Lockout, 36
Auto
adjust temperature, 3

changeover, 3
fan, 3
mode, 3

Auto Screenlock, 25
Available Modes, 31

B

B Reversing Valve, 45
Backdrop, 20
Backlight, 17
Backplate, 44
Balance Point, 36
Beep, 20

Buttons,
Back, 1
Cooler, 1, 3

Fan, 1, 3
Home, 1
Mode, 1, 3
Menu, 1, 7
Warmer, 1

C

C, 44
Calibration, 37
Celsius, 31
Cleaning, 2, 18
Clock
Display, 1

Setting, 5

ColorTouch Assistant, 40
Compressor Lockout, 33
Cool

1st stage deadband,
see Deadband
2nd stage deadband,
see Deadband
Minutes of runtime, 27

Custom Wallpaper, 20
Cycles Per Hour, 33

D

Daylight Savings, 6
Deadband
1st stage, 34

2nd stage, 34
3rd stage, 34
4th stage, 34

Page 50

Dealer Information, 27, 38
Delay
Fan-off, see Fan

Time between stages,
see Time Delay

Differential
Heat and cool, 33
Dimmer, 17
Dip Switches
ELEC, 45

electric heat, 45
GAS/EL, 45
GAS, 45
HP, 45
heat pump, 45
O, 45
B, 45

Disabled Buttons
see Security
Display, 17

Dual Fuel
changeover balance

point, 36
control two heat
sources, 36
operation, 36
outdoor sensor, 36, 48

E

Electric Heating
Aux heat, 33

Dip switch setting, 45
Lockout, 36

Index

Emergency Heat, 39
Energy Watch
Cool, 27

Heat, 27
Aux heat, 27

F

Factory Defaults
resetting, 38
Fahrenheit, 31
Fan

button function, see
Buttons

off time delay, 37
on during heat, see

Electric Heat

runtime, 27
2nd stage heat, see

Emergency Heat

Free Cooling, 35, 48

G

Gas/Electric Furnace

dip switch, 45

General Setup, 31

H

Heat

1st stage
deadband, see

Deadband

emergency heat, 39
minutes of runtime, 27
2nd stage
deadband, see

Deadband

electric strip heat,
see Aux Heat
minutes of runtime, 27
3rd stage
deadband, see

Deadband

4th stage
deadband, see

Deadband

timer, 34
turnoff point, 34
electric/heat pump, 36
mode, 3

program, see Schedule
runtime, see Runtime
setpoint, 3

Heat/Cool Indicator, 20

Heat Pump

aux heat, 33,36
aux heat lockout, 36
emergency heat, 39
heat pump lockout, 36
dip switch setting, 45
multi-stage, 33, 36

I

Idle Brightness, 17
Information, 27
Installation Settings, 33
Installation, 42

K

Keypad, 25

L

Language, 32
Lock
see Security
Logo, 38

Page 51

Index

M

Main Menu, 1, 7
Maintenance, 18
Manual

changeover, 32
cool, 3
heat, 3

Mode, 1, 3
Mode Restrictions, 25
Morning Warm-up,
see Smart Recovery
Multi-Stage
Operation, 3

N

Night Dimmer, 17
Non-Programmable
Thermostat, ii

O

O Reversing Valve, 45
Off Mode, 3
Outdoor
calibrate, 37
high and low temp, 1

sensor, 48
viewing temp, 1

P

Passcode, 25
Photos, 20, 41
Preferences, 20
Program
daily schedule, 8

R

Reset

alert messages, 15
thermostat settings,
see Factory Defaults
runtime,
fan/filter, 15
UV light, 15

Reversing Valve, 45, 47
Runtime
resetting, see Reset

service filter, 15
UV light, 15
viewing, 15, 27

S

Schedule

turn on/off, 8
view, 8
edit, 8

Page 52

Screen Cleaning, 18
Screensaver
turn on/off, 13

setup, 13
preview, 13

SD Card, 31
2nd stage turn off
temperature, 34
Security, 25
Sensor

outdoor,
thermostat,

Service
alerts, 15

information, 15, 27

Set Clock, see Clock
Setpoint
balance point, 36

cool, 3
heat, 3
limits, 25
vacation, 23

Settings, 30
Simple Thermostat, 32
Smart Fan, 11
Smart Recovery, 32
Sound Options, 20
Stages, 33

T

Terminals, see
Backplate

Test Outputs, 37

Index

Themes, 30
Thermostat Sensor
calibrate, 37
Three Stage Heat, 33
Time, see Clock
Timers, 33
Time Delay,
compressor lockout, 33

cycles per hour, 33
1st stage to 2nd stage, 34
2nd stage to 3rd stage, 34
3rd stage to 4th stage, 34

Time schedule, see
Schedule

Touch Calibration, 18

U

Upgrade Firmware, 38
User Interface Themes, 30
UV Light,

resetting, 15
runtime, see Runtime
setting, see Runtime

V

W

W1, 44
W2, 44
W3, 44
Wallpaper, 20
Warranty, 56
Wiring, 46

dual fuel, 48
free cooling, 48
gas/electric, 46
heat pump, 47

Y

Y1, 35, 44
Y2, 35, 44

Vacation, 22

modes, 23
schedule, 22
setpoints, 23

Page 53

Notes:

Page 54

Notes:

Page 55

Warranty

One-Year Warranty - This Product is warranted to be free from defects in material and
workmanship. If it appears within one year from the date of original installation, whether or not
actual use begins on that date, that the product does not meet this warranty, a new or
remanufactured part, at the manufacturer’s sole option to replace any defective part, will be
provided without charge for the part itself provided the defective part is returned to the distributor
through a qualified servicing dealer.

THIS WARRANTY DOES NOT INCLUDE LABOR OR OTHER COSTS incurred for diagnosing, repairing,
removing, installing, shipping, servicing or handling of either defective parts or replacement
parts. Such costs may be covered by a separate warranty provided by the installer.

THIS WARRANTY APPLIES ONLY TO PRODUCTS IN THEIR ORIGINAL INSTALLATION LOCATION AND
BECOMES VOID UPON REINSTALLATION.

LIMITATIONS OF WARRANTIES – ALL IMPLIED WARRANTIES (INCLUDING IMPLIED WARRANTIES OF
FITNESS FOR A PARTICULAR PURPOSE AND MERCHANTABILITY) ARE HEREBY LIMITED IN DURATION TO
THE PERIOD FOR WHICH THE LIMITED WARRANTY IS GIVEN. SOME STATES DO NOT ALLOW LIMITATIONS
ON HOW LONG AN IMPLIED WARRANTY LASTS, SO THE ABOVE MAY NOT APPLY TO YOU. THE
EXPRESSED WARRANTIES MADE IN THIS WARRANTY ARE EXCLUSIVE AND MAY NOT BE ALTERED,
ENLARGED, OR CHANGED BY ANY DISTRIBUTOR, DEALER, OR OTHER PERSON WHATSOEVER.

ALL WORK UNDER THE TERMS OF THIS WARRANTY SHALL BE PERFORMED DURING NORMAL WORKING
HOURS. ALL REPLACEMENT PARTS, WHETHER NEW OR REMANUFACTURED, ASSUME AS THEIR
WARRANTY PERIOD ONLY THE REMAINING TIME PERIOD OF THIS WARRANTY.

THE MANUFACTURER WILL NOT BE RESPONSIBLE FOR:

1. Normal maintenance as outlined in the installation and servicing instructions or owner’s
manual, including filter cleaning and/or replacement and lubrication.

2. Damage or repairs required as a consequence of faulty installation, misapplication, abuse,
improper servicing, unauthorized alteration or improper operation.

3. Failure to start due to voltage conditions, blown fuses, open circuit breakers or other
damages due to the inadequacy or interruption of electrical service.

4. Damage as a result of floods, winds, fires, lightning, accidents, corrosive environments or
other conditions beyond the control of the Manufacturer.

5. Parts not supplied or designated by the Manufacturer, or damages resulting from their use.

6. Manufacturer products installed outside the continental U.S.A., Alaska, Hawaii, and
Canada.

7. Electricity or fuel costs or increases in electricity or fuel costs for any reason whatsoever
including additional or unusual use of supplemental electric heat.

8. ANY SPECIAL INDIRECT OR CONSEQUENTIAL PROPERTY OR COMMERCIAL
DAMAGE OF ANY NATURE WHATSOEVER. Some states do not allow the exclusion of
incidental or consequential damages, so the above may not apply to you.

This warranty gives you specific legal rights and you may also have other rights which may vary
from state to state.

Page 56

Printed on recycled paper.
P/N 88-860 Rev. 5b

Page 57