Velleman PI600M, PI60024 User Manual

DC TO AC POWER INVERTER

POWER : 600W

PI600M
PI60024

for input voltage 12V
for input voltage 24V

ATTENTION – OPGELET - ACHTUNG

OVERLOADING THIS DEVICE OR CONNECTING IT WITH AN IN DUCTIVE LOAD (e.g. refriger ator, fan,
drill) WILL DAMAGE IT AND AUTOMATICALLY VOID THE WARRANTY !!

HET TOESTEL ZAL WORDEN BESCHADIGD INDIEN U HET OVERBELAST OF ER EEN INDUCTIEVE
BELASTING (vb. koelkast, boormachine, ventilator) OP AANSLUIT. DE GARANTIE VERVALT DAN
AUTOMATISCH !!

LA SURCHARGE DE L’APPAREIL OU LA CONNEXION D’UNE CHARGE INDUCTIVE (p.ex. vent ilat eu r,
réfrigérateur, perceuse) ENDOMMAGERONT L’APPAREIL ET LA GARANTIE SERA INVALIDEE
AUTOMATIQUEMENT !!

DIE GARANTIE ERLISCHT UND DER SPANNUNGSWANDLER KANN BESCHÄDIGT WERDEN, WENN SIE
IHN ÜBERL ASTEN ODER MIT EINER INDUKTIVEN LAST VERBINDEN (z.B. Kühlschrank, Lüfter,
Bohrmaschine).

User Manual
Gebruikershandleiding
Manuel d'utilisation
Bedienungsanleitung

1. DESCRIPTION

voltage

indicator

power

switch

crocodile

clips

AC output

socket

2. CONNECTIONS
Connect the red cable from the "+" terminal (red term inal ) of the battery to the +

binding post (red connection) of the inverter and the black c able from the "-"
terminal (black terminal) of the battery to the "-" binding post (black connection) of
the inverter. The length of the cable is ≤ 2m.

Be sure to tighten the screws in order to avoid loos e con necti on.

3. OPERATION
When connected to an appliance, remember to turn on the inverter before turning

on the appliance. If the buzzer sounds during operation, this indicates that the
battery voltage is very low and that the inverter will be disconnected in 5 minutes.

then the

device

Switch on

inverter

PI600M & PI60024 v2 GB 1

4. OUTPUT CAPACITY
The inverter will switch off automatically if the total wattage of the electrical

appliances exceeds the inverter's output capacity. This will also happen if the
temperature of the inverter exceeds 55°C due to prolonged use.

5. SPECIAL RECOMMENDATIONS
Unplug the AC inverter when not in use and when starting the vehicle's motor.
If the AC inverter makes a beeping sound : switch off your appliance, unplug the

inverter and restart your vehicle's engine. The beeping sound is simply the low­battery warning, which indicates that the voltage of your battery is getting low.
Your inverter will shut down automatically if you do not restart your engine and
continue the use of your inverter. This will leave your vehicle's battery at about

10.5VDC (21VDC when using a 24V inverter), enabling you to start your engine
and resume operation of the inverter. It also eliminates the possibil ity of being
stranded with a dead battery.

To avoid over-discharging the battery, you should let your engine run for 10 to 20
minutes after every 2-3 hours of use. This allows your vehicle's battery to recharge.

Please remember to connect the "+" wire to the "+" terminal and the "-" wire to the
"-" terminal if you choose to use an adapter in order to establis h a di rect
connection between the AC inverter and the battery terminals. IF YOU CONNECT
THE WIRES TO INCORRECT TERMI NALS, THE POLARITY WILL BE
REVERSED AND THIS WILL DAM AGE THE INVERTER. REVERSED
POLARITY WILL INSTANTLY VOID YOUR INVERTER'S WARRANTY.

Please remember to disconnect the AC inverter before using the battery charger
to replenish you battery's voltage. Failure to disconnect the inverter prior to
connecting a charger may result in an input spike that will damage the inverter.
CONNECTING THE INVERTER'S INPUT TO A BATTERY CHARGER WILL
VOID THE WARRANTY AND MAY DAMAGE THE INVERTER

The battery's voltage must never exceed 15VDC (30 VDC for a 24V inverter).
CONNECTING THE INVERTER TO A DC POW ER SOURCE GREATER THAN
15VDC (30VDC) WILL VOID THE WARRANTY AND MAY DAMAGE THE
INVERTER.

PI600M & PI60024 v2 GB 2