Operating Instructions
Electronics module
VEGACAP series 60
Document ID:
30174
Capacitive
Contents
Contents
1 About this document
1.1 Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2 Target group . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3 Symbolism used . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 For your safety
2.1 Authorised personnel . . . . . . . . . . . . . . . . . . . . . . . .
2.2 Appropriate use . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3 Safety instructions for Ex areas . . . . . . . . . . . . . . . . .
2.4 Environmental instructions. . . . . . . . . . . . . . . . . . . . .
3 Product description
3.1 Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2 Principle of operation . . . . . . . . . . . . . . . . . . . . . . . .
3.3 Packaging, transport and storage . . . . . . . . . . . . . . .
4 Mounting
4.1 Instructions for installation . . . . . . . . . . . . . . . . . . . . .
4.2 Mounting preparations . . . . . . . . . . . . . . . . . . . . . . .
4.3 Mounting steps. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 Setup
5.1 Setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6 Maintaining
6.1 Instrument repair . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
3
3
4
4
4
4
5
5
5
6
6
6
8
9
7 Dismounting
7.1 Dismounting steps . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2 Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8 Supplement
8.1 Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Editing status: 2012-01-17
2 Electronics module • VEGACAP series 60
10
10
11
30174-EN-120124
1 About this document
1 About this document
1.1 Function
This operating instructions manual has all the information you need for
quick mounting and setup of a replacement module. Please read this
manual before you start setup.
1.2 Target group
This operating instructions manual is directed to trained qualified
personnel. The contents of this manual should be made available to
these personnel and put into practice by them.
1.3 Symbolism used
Information, tip, note
This symbol indicates helpful additional information.
Caution: If this warning is ignored, faults or malfunctions can
result.
Warning: If this warning is ignored, injury to persons and/or serious
damage to the instrument can result.
Danger: If this warning is ignored, serious injury to persons and/or
destruction of the instrument can result.
Ex applications
This symbol indicates special instructions for Ex applications.
l List
The dot set in front indicates a list with no implied sequence.
à Action
This arrow indicates a single action.
1 Sequence
Numbers set in front indicate successive steps in a procedure.
30174-EN-120124
Electronics module • VEGACAP series 60 3
2 For your safety
2 For your safety
2.1 Authorised personnel
All operations described in this operating instructions manual must be
carried out only by trained specialist personnel authorised by the plant
operator.
During work on and with the device the required personal protective
equipment must always be worn.
2.2 Appropriate use
Electronics module CP60 is a replacement module for VEGACAP
series 60 level switches.
2.3 Safety instructions for Ex areas
Please note the Ex-specific safety information for installation and
operation in Ex areas. These safety instructions are part of the
operating instructions manual and come with the Ex-approved
instruments.
2.4 Environmental instructions
Protection of the environment is one of our most important duties. That
is why we have introduced an environment management system with
the goal of continuously improving company environmental protection.
The environment management system is certified according to DIN
EN ISO 14001.
Please help us fulfil this obligation by observing the environmental
instructions in this manual:
l Chapter "Packaging, transport and storage"
l Chapter "Disposal"
4 Electronics module • VEGACAP series 60
30174-EN-120124
3 Product description
3.1 Structure
3 Product description
Scope of delivery
Application area
Packaging
Transport
Transport inspection
The scope of delivery encompasses:
l Electronics module for VEGACAP series 60 (CP60)
l Documentation
- this operating instructions manual
3.2 Principle of operation
The electronics module CP60 is suitable for replacement in VEGACAP
series 60 capacitive level switches.
3.3 Packaging, transport and storage
Your instrument was protected by packaging during transport. Its
capacity to handle normal loads during transport is assured by a test
according to DIN EN 24180.
The packaging of standard instruments consists of environmentfriendly, recyclable cardboard. For special versions, PE foam or PE foil
is also us ed. Dispose of the packaging material via specialised
recycling companies.
Transport must be carried out under consideration of the notes on the
transport packaging. Nonobservance of these instructions can cause
damage to the device.
The delivery must be checked for completeness and possible transit
damage immediately at receipt. Ascertained transit damage or
concealed defects must be appropriately dealt with.
Storage
Storage and transport
temperature
Up to the time of installation, the packages must be left closed and
stored according to the orientation and storage markings on the
outside.
Unless otherwise indicated, the packages must be stored only under
the following conditions:
l Not in the open
l Dry and dust free
l Not exposed to corrosive media
l Protected against solar radiation
l Avoiding mechanical shock and vibration
l Storage and transport temperature see chapter "Supplement -
Technical data - Ambient conditions"
l Relative humidity 20 … 85 %
30174-EN-120124
Electronics module • VEGACAP series 60 5
2
1
4 Mounting
4 Mounting
4.1 Instructions for installation
If the electronics module is defective, it can be replaced by the user.
In Ex applications only one instrument and one electronics module with
respective Ex approval may be used.
4.2 Mounting preparations
In general, all electronics modules of series CP60 can be inter-
changed. If you want to use an electronics module with a different
signal output, you can download the corresponding operating
instructions manual from our homepage under Downloads.
4.3 Mounting steps
Mounting steps
To exchange the electronics module, proceed as follows:
1 Switch off power supply
2 Unscrew the housing cover
3 Lift the opening levers of the terminals with a screwdriver
4 Pull the connection cables out of the terminals
5 Loosen the two screws with a screw driver (Torx size T10 or slot 4)
Fig. 1: Loosening the holding screws
1 Electronics module
2 Screws (2 pcs.)
6 Pull out the old electronics module
7 Compare the new electronics module with the old one. The type
label of the electronics module must correspond to that of the old
electronics module. This applies particularly to instruments used in
hazardous areas.
30174-EN-120124
6 Electronics module • VEGACAP series 60
2
1
4 Mounting
8 Compare the settings of the two electronics modules. Set the
adjustment elements of the new electronics module to the same
setting of the old one.
Information:
Make sure that the housing is not rotated during the electronics
exchange. Otherwise the plug may be in a different position later.
9 Insert the electronics module carefully. Make sure that the plug is
in the correct position.
10 Screw in the two holding screws and tighten them
11 Insert the wire ends into the open terminals according to the wiring
plan
12 Press down the opening levers of the terminals, you will hear the
terminal spring closing
13 Check the hold of the wires in the terminals by lightly pulling on
them
14 Check cable gland on tightness. The seal ring must completely
encircle the cable.
15 Mount the probe into the vessel. Make sure that the probe is
uncovered.
Fig. 2: Compensation key
1 Measuring range selection switch (compensation key)
2 Control lamp
16 Push the measuring range selection switch (1) as long as the
control lamp (2) flashes green.
17 Hence the probe is compensated to the modified length.
18 Carry out the adjustment again. See chapter "Set-up, adjustment
elements".
19 Screw the housing cover back on
The electronics exchange is now finished.
As a rule, an exchange of electronics must be documented internally
when Ex applications are involved.
30174-EN-120124
Electronics module • VEGACAP series 60 7
5 Setup
5 Setup
5.1 Setup
Setup
Make sure that all adjustment elements are set to the settings of the
old electronics module. Hence the sensor is immediately ready for
operation.
In general, all oscillators of series CP60 can be interchanged.
If you want to use an electronics module with a different signal output,
you can download the corresponding operating instructions manual
from our homepage under Downloads.
8 Electronics module • VEGACAP series 60
30174-EN-120124
6 Maintaining
6 Maintaining
6.1 Instrument repair
If a repair is necessary, please proceed as follows:
You can download a return form (23 KB) from our homepage at www.
vega.com under: "Downloads - Forms and certificates - Repair form".
By doing this you help us carry out the repair quickly and without
having to call back for needed information.
l Print and fill out one form per instrument
l Clean the instrument and pack it damage-proof
l Attach the completed form and, if need be, also a safety data
sheet outside on the packaging
l Please ask the agency serving you for the address of your return
shipment. You can find the respective agency on our website
www.vega.com under: "Company - VEGA worldwide"
30174-EN-120124
Electronics module • VEGACAP series 60 9
7 Dismounting
7 Dismounting
7.1 Dismounting steps
Take note of chapters "Mounting" and "Connecting to power supply"
and carry out the listed steps in reverse order.
7.2 Disposal
The replacement module consists of materials which can be recycled
by specialised recycling companies. We have purposely designed the
electronic modules to be easily separable.
WEEE directive 2002/96/EG
This instrument is not subject to the WEEE directive 2002/96/EG and
the respective national laws (in Germany e.g. ElektroG). Pass the
instrument directly on to a specialised recycling company and do not
use the municipal collecting points. These may be used only for
privately used products according to the WEEE directive.
Correct disposal avoids negative effects on humans and the environment and ensures recycling of useful raw materials.
Materials: see chapter "Technical data"
If you have no way to dispose of the replacement module properly,
please contact us concerning return and disposal.
10 Electronics module • VEGACAP series 60
30174-EN-120124
8 Supplement
8.1 Technical data
Technical data
are stated in the operating instructions manual of the respective sensor.
8 Supplement
30174-EN-120124
Electronics module • VEGACAP series 60 11
VEGA Grieshaber KG
ISO 9001
Am Hohenstein 113
77761 Schiltach
Germany
Phone +49 7836 50-0
Fax +49 7836 50-201
E-mail: info.de@vega.com
www.vega.com
Printing date:
All statements concerning scope of delivery, application,
practical use and operating conditions of the sensors and
processing systems correspond to the information avail-
able at the time of printing.
© VEGA Grieshaber KG, Schiltach/Germany 2012
Subject to change without prior notice 30174-EN-120124
Loading...