Vdo HC12.6 User Manual [ru]

Download

CYCLECOMPUTING

INSTRUCTION MANUAL

BEDIENUNGSANLEITUNG

MANUEL D´INSTALLATION ET D´UTILISATION

MANUALE D´INSTALLAZIONE E FUNZIONAMENTO

INSTALACION Y OPERACIÓN MANUAL

HANDLEIDING

HC12.6

screw

1-5 mm

LOCK

UNLOCK

OPEN CLOSE

OPEN

IMPORTANT

Rubber washer

Press AC-Button to Begin or install battery (P6)

automatic

•••••••

Press MODE 2 for next press MODE 1 to select

WS in mm / inch

P10

ETRTO WS in mm KMH WS in inch MPH

47-305 16x1,75 1272 50,1 47-406 20x1,75 1590 62,6 34-540 24x1 3/8 1948 76,7 47-507 24x1,75 1907 75,1 23-571 26x1 1973 77,7 40-559 26x1,5 2026 79,8 44-559 26x1,6 2051 80,7 47-559 26x1,75 2070 81,5 50-559 26x1,9 2089 82,2 54-559 26x2,00 2114 83,2 57-559 26x2,125 2133 84,0 37-590 26x1 3/8 2105 82,9 20-571 26x3/4 1954 76,9

ETRTO WS in mm KMH WS in inch MPH

32-630 27x1 1/4 2199 86,6 40-622 28x1,5 2224 87,6 47-622 28x1,75 2268 89,3 40-635 28x1 1/2 2265 89,2 37-622 28x1 3/8 2205 86,8 18-622 700x18C 2102 82,8 20-622 700x20C 2114 83,2 23-622 700x23C 2133 84,0 25-622 700x25C 2146 84,5 28-622 700x28C 2149 84,6 32-622 700x32C 2174 85,6 37-622 700x37C 2205 86,8 40-622 700x40C 2224 87,6

SET Metric System

P11

SET WS 1

Start at TRIP DIST

Press MODE 1 for 3 sec.

Press MODE 1

3 sec. to end

Press MODE 2 to select between KMH and MPH

•••••

Press MODE 1

to switch

Press MODE 1

to set WS1

•••••••••••••••••••••••••••••••••••••••••••••••••••

SET WS 2

Press MODE 2

to increase

••••••

••••••••••••

•••••

Press MODE 1 to set WS2

Press MODE 1 3 sec.

to end without setting WS2

Press MODE 2

to increase

Press MODE 1 to

switch and

MODE 2 to increase

continue for

all4 digits

P12

Press MODE 1

3sec.to start

Press MODE 2 to switch between 24h or 12h

Press MODE 1

3 sec. to end

Press MODE 1

to set the hours

Press MODE 2 to increase the

minutes

MODE 2 to

increase the hours

Press MODE 1

to set the minutes

Set

P13

P14

•••••••

Press MODE 1

3sec.to start

Reset

Important

Navigator in Display

Press MODE 2

to increase

Press MODE 2

to reset

Press MODE 1

to switch

Press MODE1 3 sec. to end

after you set the navigator

•••••••

••••••••••••••••••••••••••

Set ODOMETER

P15

Press MODE 1

3sec.to start

Press MODE 2

to increase

Press MODE 1

to switch

Press MODE1 3 sec. to end after you set the odometer

••••••••••

•••••••

BIKE CHECK

P16

Press any button

BIKE CHECK disappears

The service icon will remain flashing.

Another 50 km/35 mi.

Then the service interval

icon will also disappear

P17

Set limits

P18

High-limit

Press MODE1

3sec.

Press MODE 2

to increase

Press MODE1

to end

Press MODE1

to set Low Limit

Low-limit

Press MODE 2

to decrease

P19

Press PULS

Press MODE1+ MODE2 to stop

Press MODE1+

MODE2 to start again

OWNER'S MANUAL - VDO HC 12.6

Index

Preface

1. Mounting 4.3 Entering time / clock

1.1 Handlebar holder 4.4 The NAVIGATOR

1.2 Speed transmitter (sensor) 4.4.1 Presetting the NAVIGATOR

1.3 Spoke magnet 4.4.2 Resetting the NAVIGATOR to zero

1.4 Twist-Click mounting of computer 4.5 Presetting the odometer onto handlebarholder 5. Service interval indicator

2. Basic information on how to operate your VDO HC 12.6 6. Sleep mode

2.1 Interrogating information 7. Heart rate information of your VDO HC 12.6

2.2 Calling set-up mode 8. Putting on the chest belt

2.3 Button / key covering in set-up mode 9. Presetting your upper and lower heart rate limits

2.4 Resetting of information modes to zero 10. The stopwatch

2.4.1Cycling Information 10.1 Stopwatch (automatic)

2.4.2Heartrate Information 10.2 Manual operation of the stopwatch

2.4.3NAVI GATOR 11. Calling up your average heart rate

3. Installing the batteries 12. Display of training times within preset target range training zones.

3.1 Installing battery into computer head 13. Activating / deactivating the BEEPER

3.2 Installing battery into chest belt transmitter 14. FAQ / Troubleshooting

4. Initial set-up of your VDO HC 12.6 15. Warranty

4.1 Selecting your language 16. Technical data

4.2 Selecting the wheelsize 17. Packaging contents

4.2.1How to determine the precise wheelsize

4.2.2How to switch from wheelsize 1 to wheelsize 2

4.2.3Entering the precise wheelsize

12.6

Preface

Thank you very much for buying a VDO HC 12.6 bicycle computer featuring heart rate / pulse functions. The more familiar you get with this model, the more enjoyable your trips are going to be.

12.6

Hence, our urgent request: Please read thoroughly all the information provided in this manual. You are getting important and useful hints for operation to make you fully benefit from all the technical features of your VDO HC 12.6.

We wish you enjoyable trips and rides on your bike with VDO

1.Mounting

1.1 Mounting the handlebar holder

The handlebar holder fits handlebars of any diameter. Before mounting the system, decide if you will be using your left or right hand to operate the computer and then mount the handlebar holder on the respective side. Position the handlebar holder, insert the strap and adjust it by tightening the screw.

Warning: Before tightening the handlebar holder, make sure to adjust the position of the computer head (inclination) when the LCD-display is best visible

for you. Only when you find the best position tighten the screw.

1.2 Mounting the speed transmitter / sensor

The sensor should be mounted on the same side of the fork as the holder is on the handlebar. While mounting, be sure that there is ample cable left for left and right turns of your handlebar, do not lay the cable too tight.

CYCLE PARTS GMBH

Important: Do not tighten the cable ties yet. Accurately position the sensor and the spoke magnet first, then tighten the cable ties.

1.3 Mounting the spoke magnet

Distance between magnet and sensor should be approx. 1-5 mm. In case this distance is not achievable in the current position, slide the sensor and the magnet on the fork or spoke accordingly.

1.4 Twist-Click mounting of computer on to holder

The Twist-Click mounting has been exclusively developed for the new line of VDO computers. The VDO HC 12.6 also features the Twist-Click-System. The computerhead is put onto the handlebar and by a right turn of the computerhead (TWIST) fixed to the holder (CLICK). It is just as easy to remove the computerhead from the handlebar holder. Twist it to the left, remove computerhead from handlebar holder.

2. Basic information on how to operate your VDO HC 12.6

Make sure you are familiar with the computers basic operating instructions before the initial set-up and use.

Your VDO HC 12.6 features 3 keys / buttons Left ...... Center Right

The display

The following information is permanentely displayed:

• current / actual speed in KMH or MPH accurate to +/- 0.5 KMH / MPH

• symbol (MPH or KMH) for the conversion selected,

• wheelsize selected: Bike 1 (WS1) or Bike 2 (WS2)

• symbols to compare actual speed and average speed (up-arrow, down-arrow, dot)

• heart-symbol, that indicates pulse signals are being transmitted

• LO Pulse, preset lower limit of your training target zone

• HI Pulse, preset upper limit of your training target zone

• Note-symbol to indicate acoustic alarm ON/OFF

MODE1.....PULSE....MODE2

Function

TRIP DIST RIDE TIME AVG SPEED MAX SPEED

MODE 1

Function

NAVI GATOR CLOCK ODO METER1 ODO METER2 ODO TOTAL

MODE 2

Function

STOP WATCH AVG PULSE MAX PULSE TIME ABOVE TIME IN TIME BELOW

PULSE

12.6

2.1 Interrogating information

With the MODE1 key you call up following information: TRIP DIST/ RIDE TIME/ AVG SPEED/ MAX SPEED

12.6

TRIP DIST trip counter for your individual trip, counting to 999.99 KM or M RIDE TIME trip timer featuring automatic start/stop function up to 19:59:59 h AVG SPEED average speed, accurate to two decimal points MAX SPEED maximum speed achieved during a ride up to199.5 KM or M

Important: If the ride timer overflows 19:59:59 h, it is automatically reset to 00:00:00. Simultaneously, your average speed counter AVG SPEED is reset

to zero. If your trip counter overflows 999.99 KM or M, it is automatically reset to 000.00 Simultaneously, your average speed counter AVG SPEED and your ride timer RIDE TIME are reset to zero.

With the MODE 2 key you call up following information: NAVI GATOR/ CLOCK/ ODO1 METER/ ODO2 METER/ ODO TOTAL

NAVI GATOR Second, manual trip counter, can be reset to zero individually, can be preset and counting up from there on. CLOCK Time of the day in 12h or 24h mode ODO 1 METER Odometer (sum of all trips) on Bike 1, up to 99.999 KM or MI. ODO 2 METER Odometer (sum of all trips) on Bike 2, up to 99.999 KM or MI. ODO TOTAL Odometer (sum of all trips on both bikes), sum of Bike 1 and Bike 2, up to 199.999 KM or M.

Important: Switching conversions from mi to km at odometer 62.111 mi and up leads to a reset to zero of the odometer. (62.111 mi converts to approx

100.000 km but the display holds 99.999 km max.)

With the PULSE key you call up following information: STOP WATCH/ AVG PULSE/ MAX PULSE/ TIME ABOVE/ TIME IN/ TIME BELOW

STOP WATCH stop watch to keep track of your pulse training times, both automatic and manual start/stop possible, up to 19:59:59 h. AVG PULSE average pulse / heart rate during a training period. MAX PULSE maximum pulse during a training period TIME ABOVE time in which your pulse was above the preset upper limit TIME IN time in which your pulse was right in-between the preset upper and lower limits, per say, in your target zone. TIME BELOW time in which your pulse was below the preset lower limit

2.2 Calling up set-up modes

The MODE 1 key calls up any set-up mode Calling up the set-up modes requires a 3 sec pressing of the MODE 1 key.

Set-up modes can be entered from various information displays:

You want to set up: Display Information needed

Wheelsize 1 or Wheelsize 2 TRIP DIST Clock CLOCK Odometer for Bike 1 ODO 1 METER Odometer for Bike 2 ODO 2 METER Navigator, second trip counter NAVIGATOR Upper and lower limits for pulse STOP WATCH or AVG PULSE or TIME ABOVE or TIME IN or TIME BELOW

2.3 Button / key covering in set-up mode

Once you have entered a set-up mode with MODE 1, the keys have the following (different) functions. MODE 1 key: jump from digit to digit; exit set-up mode (pressing MODE 1 for 3 sec.) MODE 2 key: increase/change of digit selected; selecting display symbols

12.6

2.4 Resetting of information modes to zero

By pressing MODE 2 for 5 sec. any of the following information is simultaneously reset to zero

12.6

2.4.1. Cycling Information

Get any of these informations in display TRIP DIST--RIDE TIME--AVG SPEED--MAX SPEED Press MODE 2 for 5 sec. to reset all of above information symultaneously.

2.4.2 Heartrate Information

Get any of these informations in display STOP WATCH--AVG PULSE--MAX PULSE--TIME ABOVE--TIME IN--TIME BELOW Press MODE 2 for 5 sec. to reset all of above information symultaneously.

2.4.3 NAVI GATOR

Call NAVI GATOR in your display Press MODE 2 for 5 sec, information is being reset to zero.

3. Installing batteries

3.1 Installing the battery into the computer head

To save battery power, your VDO HC 12.6 comes with the battery not yet fitted. Prior to initial use the batteries will first have to be installed with the positve pole on top.

Warning: Once the battery is installed your VDO HC 12.6 start the set-up of display language. See also chapter 4.1

If you find the computer is not functioning properly after the battery is changed, push the AC-button (Auto Clear) on the rear side of the computer to reset. P6

3.2 Installing the battery into the chest belt

Open the battery door with a coin and remove it. Install the battery with the positve pole on top. Be sure that the rubber washer ist precisely positioned when closing the battery door.

4. Initial setup of your VDO HC 12.6

4.1 Selecting display language

After installing the battery or pressing the AC-button your VDO HC 12.6 automatically requests a display language to be selected. After installing the battery, your VDO HC 12.6 first greets you in English (by default) displaying "ENJOY YOUR HC12.6" The VDO HC12.6 will then automatically request you to select your display language. The VDO HC 12.6 subsequently displays 7 languages, i.e.: ENTER LANGUAGE, -- EINGABE SPRACHE--CHOIX LANGUE--REGOL LINGUA--ENTER TAAL--AJUST LENGUA--USTAW JEZYK.

After this automatic scroll you can then select your language. I.e. "LANGUAGE ENGL" will be in display By pressing the MODE 2 key (right), the various languages will be displayed.

Process: LANGUAGE ENGL M2> SPRACHE DEUT M2> LANGUE FRAN M2> LINGUA ITAL M2> TAAL NEDL M2> LENGUA ESPAN M2> JEZYK POLSK Once your language is displayed, press the MODE 1 key for 3 sec. Your selected language is now stored, any further information is displayed in that language.

The display now shows TRIP DIST, if you have chosen English for your language. P8

12.6

4.2 Selecting the wheelsize

Your computer VDO HC 12.6 indicates your wheel size as WS (Wheelsize) = wheel circumference. Your VDO HC 12.6 is able to process two different wheelsizes for two different bikes (i.e. road bike and mountainbike)

12.6

The following default values are preset

Wheelsize 1 WS1 = 2155 mm wheel circumference Wheelsize 2 WS2 = 2000 mm wheel circumference

Warning: After a battery change the above defaults are automatically applied.

After a battery change, you have to re-enter the precise values for your bike.

4.2.1 How is the wheelsize precisely determined??

Place the front wheel of your bike with the valve at the bottom, mark this position with a line and push your bike ahead until exactly one rotation of the front wheelis completed. Draw another line where the valve now is. Take a ruler and measure the distance between marks 1 and 2 which reflects the wheelsize = wheel-circumference. The figure measured (inches or mm) is the wheelsize to be entered into your computer.

If you have selected MPH readout you must enter your wheelsize in inches. If you have selected KMH readout you must enter your wheelsize in mm.

Standard wheelsizes and respective values in mm and inches.

4.2.2 How to switch from wheelsize 1 to wheelsize 2

You can switch from wheelsize 1 (WS 1) to wheelsize 2 (WS 2) and vice-versa by pressing the MODE 1+ MODE 2 button for 3 sec.

P10

4.2.3 Entering the precise wheelsize

Step 1: By pressing MODE 1 call TRIP DIST in your display. Step 2: Press MODE 1 for 3 sec. In the upper part of the display you see "WS1" and "KMH" or "MPH" flashing. The lower part of the display alternately shows

"ENTER MTRIC SYSTM" and "KMH"/"MPH"

Step 3: With MODE 2 you choose whether you want kilometers=KMH oder miles=MPH as a measuring unit. Step 4: Once the conversion of KMH or MPH has been chosen, you proceed by briefly pressing (0.1 sec) MODE 1. The lower part of the display now alternates

"ENTER WHEELSIZE1" and 2155. The last number "5" flashing. or 84.8. (if MPH selected)The last number "8"flashing.

Step 5: With MODE 1 and MODE 2 you enter your measured wheelsize 1 (bike1). MODE 2 increases the flashing number MODE 1 jumps to the next number,

see set-up mode.

Step 6: Once you have entered the last number of wheelsize 1 and press the MODE 1 button, the computer automatically jumps to the setup mode for

wheelsize 2. The lower part of the display alternately shows "ENTER WHEELSIZE2" and 2000 with the last number "0" flashing. Enter your wheelsize 2 as described in Step 5.The lower part of the display alternately shows "ENTER WHEELSIZE2" and 2000 or 78.7 (if MPH selected) with the last number "0" or "7" flashing.

Step 7: Once you have entered wheelsize 2, press MODE 1 for 3 sec to exit set-up mode. The computer will return to displaying TRIP DIST. P11

Warning: Exiting setup procedure before having completely entered the precise wheelsize may lead to faulty readouts.

4.3 setting the clock CLK

Your VDO HC 12.6 features a clock with hour and minute display in12 or 24 h mode. To access the clock setup mode proceed as follows:

Step 1: MODE 2 calls the CLK information into your display Step 2: Press the MODE 1 for 3 sec. The set-up mode for the clock starts. The lower part of the display alternately shows "ENTER CLOCK" and "24h"/12h Step 3: With MODE 2 you choose whether you want your time in a 24 or 12 hour mode. Step 4: With MODE 1 you start the hour setup. The hour display will be flashing and can be changed with MODE 2. Step 5: With MODE 1 you start the minute setup. The minute display will be flashing and can be changed with MODE 2. Step 6: Once hours and minutes are correctly entered, you exit CLK set-up mode by pressing MODE 1 for 3 sec.

P12

12.6

4.4 The NAVIGATOR

The NAVIGATOR is a second, individual trip distance counter that can be:

• manually reset to zero

12.6

• preset to a certain value, the trip distance is then counted from this value. The NAVIGATOR is very helpful following road book instructions or tour suggestions of bike magazines. For example, your road book tour wants you "to go straight for a mile and then make a right turn, then go on for half a mile and make a sharp left turn".

These instructions can be precisely followed by using the NAVIGATOR. Once you have arrived at the first intersection after the first mile, you reset the NAVIGATOR to zero and and follow the next leg for half of a mile. At the second intersection you reset to zero again and follow the next instruction of your road book.

The NAVIGATOR can be preset and proceed from this individual value. For example, you are unable to start your tour at the point 0 km/m, but at 5.3 km. This value can be preset / entered into the NAVIGATOR. The NAVIGATOR will then count on from 5.3 km.Also after a mistake in following the road book, you can reset/reenter the correct value.

4.4.1 Presetting the NAVIGATOR

Step 1: MODE 2 calls NAVIGATOR into display Step 2: Press MODE 1 for 3 sec. The lower part of the display alternetely shows "ENTER NAVIGATOR" and "000.00" with the last digit "0" flashing. Step 3: By pressing MODE 2 you increase the flashing number, by pressing MODE 1 you jump to the next number 000.00, etc. Step 4: Once the NAVIGATOR is preset, exit setup mode by pressing MODE 1 for 3 sec. The display shows NAVIGATOR and the preset value.

Your VDO HC 12.6 will be counting on from this preset value.

4.4.2 Resetting the NAVIGATOR to zero

Step 1: MODE 2 calls NAVIGATOR into display Step 2: Press MODE 2 for 5 sec., the value indicated is being reset to zero. Your VDO HC 12.6 will be counting on from zero.

Warning: Before resetting to zero, make sure the information NAVIGATOR is called in.

If NAVIGATOR is not in the display, you are accidentally re-setting other information to zero.

P13

P14

4.5 Presetting the odometer

After a battery change, you can re-enter previous odometer values (for both bikes) into your VDO HC 12.6.

Step 1: With MODE 2 call "ODO1 METER" or "ODO2 METER" into display, depending which one of these values you want to re-enter. Step 2: Press MODE 1 for 3 sec. The lower part of the display alternately shows "ENTER ODO1 METER" or "ENTER ODO2 METER" plus the

respective value with the last number flashing.

Step 3: With MODE 2 you increase the number, with MODE 1 you jump to the next number etc. Step 4: Once you have entered your values for ODOMETER 1 and ODOMETER 2, you exit set-up mode by pressing MODE 1 for 3 sec.

5. Service Interval Indicator

Your VDO HC 12.6 features a Service Interval Indicator to remind you to have your bike serviced at your trusted bike shop.The service interval reminder is indicated separately for both your bikes. Every 750 km / 468 mi, the service icon is activated. The service icon flashes and the lower part of the display shows "BIKE CHECK" By pressing any of the buttons, the "BIKE CHECK" information disappears. Other information can still be reviewed. The service icon will remain flashing.

P15

After another 50 km / 35 mi, the service interval icon will also disappear.

6. Sleep-Mode

Your VDO HC 12.6 features SLEEP-Mode. During SLEEP-Mode the display is shut down. The clock and, if activated, the service interval icon, remain displayed.

P16

Additionally, the internal receiver for pulse signals is also shut down in order to save battery power!

Your VDO HC 12.6 automatically goes into SLEEP-Mode after 5 min if SLEEP-Mode is terminated if

• no buttons are pressed • any button is pressed

• no speed impulses are processed • speed impulses are processed

• no pulse signals are received

Warning: If you want pulse signals to be received and processed while you are off your bike, the SLEEP-Mode must be cancelled by switching the computer

on / pressing any button.

12.6

7. Pulse information of your VDO HC 12.6

Your VDO HC 12.6 permanentely displays following pulse / heart rate information:

• Actual pulse / heart rate

12.6

• Lower limit LO

• Upper limit HI

• Heart icon to indicate receiption of signals

• Audible alarm / beeper (if activated) Information that is displayed by pressing the PULSE button

STOP WATCH Manual stopwatch for your pulse values AVG PULSE Your average pulse within a training period MAX PULSE maximum pulse during a training period TIME ABOVE Indication of the time your pulse / heart rate is above the pre-set limit TIME IN Indication of the time your pulse / heart rate is between the pre-set upper and lower limit. TIME BELOW Indication of the time your pulse / heart rate is below the pre-set limit

The pulse information can be viewed by pressing the PULSE button in the following order. STOP WATCH/ AVG PULSE/ MAX PULSE/ TIME ABOVE/ TIME IN/ TIME BELOW

8. Putting on the chest belt

Men have to put on the chest belt below the pectoral muscles, women below the bust on the ribs. Electrodes incorporated to the chest belt measure your pulse.

To ensure precise measuring either the electrodes or your skin must be moistened.

A little water or saliva will do that. Later, during training, your sweat is then providing the required moist. The chest belt must not be put on too tight or your breathing may become hindered. The perfect fit of the chest belt is achieved by adjusting the elastic strap. When done training you may clean the chest belt by rinsing it with warm water. The elastic strap is machine washable

The flashing heart icon in the display indicates the functioning transmission of pulse signals from the chest belt to the computer. P17

9. Setting of pulse limits

With your VDO HC 12.6 you determine upper and lower limits for your pulse / heart rate to define your training zone. During initial setup or when the AC-button at the rear of the housing has been pressed, following values apply by default:

• Lower limit LO 80

• Upper limit HI 140

Step 1: Call any pulse information into display by pressing the PULSE button. Step 2: Press MODE 1 for 3 sec. The lower part of the display alternately shows "ENTER and HIGH LIMIT" plus the number "140" or the value

you have last entered. The middle part of the display shows "HI" and the respective value

Step 3: By pressing MODE 2 you can change this value, pressing once increases by 1, constant pressing increases by increments of 5, i.e. up to 160.

Upper limit may be set from 80 to 220 beats per minute. Exceeding 220, setup will start anew at 80.

Step 4: Once your upper limit is set, i.e. 160, MODE 1 will compulsorily take you to setup your lower limit.

The lower part of the display alternately shows "ENTER and LOW LIMIT" plus the number "150" (= set value for upper limit minus 10). The middle part of the display shows "LO" and the respective value, here "150".

Step 5: By pressing MODE 2 you can change this value, pressing once decreases by 1, constant pressing decreases by increments of 5, i.e. "145". Step 6: Once you have set up your lower limit, you may exit setup by pressing MODE 1 for 3 sec.

Preset values for your upper and lower pulse limits are permanentely displayed in the middle part of the LCD. (HI and LO)

12.6

P18

10. The stopwatch

10.1 Stopwatch (automatic)

12.6

With your VDO HC 12.6 running (not in Sleep-Mode), the receiver for pulse signals is activated as well. As soon as the chest belt (sender) starts transmitting pulse signals, the STOPWATCH will start automatically.

The STOPWATCH may also be manually started and stopped. (see manual operation of the stopwatch). If you don't stop the STOPWATCH manually, it stops automatically as soon as the receiver is no longer being transmitted pulse signals from the chestbelt

sender. For example, you have put off the chestbelt after your training or the distance between receiver (computer) and sender (chestbelt) has become too big.

Only with the STOPWATCH running, values and information for TIME ABOVE--TIME IN--TIME BELOW and AVG PULSE can be processed and displayed.

10.2 Manual operation of the STOPWATCH

Only with the receiver (computer) on and the chestbelt transmitting pulse signals (actual pulse displayed), the STOPWATCH is manually operable.

Step 1: By pressing PULSE call STOPWATCH in your display Step 2: To either stop or restart the STOPWATCH press MODE 1 and MODE 2 simultaneously.

Once you have put your STOPWATCH to an halt, the lower part of the display alternately shows "STOPWATCH" and the respective value. Additionally you see "FREEZ". "FREEZ" indicates that the STOPWATCH has been put to a manual halt. Restarting the STOPWATCH (MODE 1 and MODE 2 simultaneously), your display shows "STOPWATCH" and the respective value. "FREEZ" will then disappear from the display.

11. Calling up your average pulse / heart rate

AVG PULSE information is called up by pressing the PULSE key. Average pulse is calculated by the number of heartbeats and the STOPWATCH time.

With the STOPWATCH manually put to halt, average pulse can only be calculated for the time measured to date.

With the STOPWATCH manually put to halt and calling up AVG PULSE, the lower part of the display alternately shows the then actual value and "FREEZ".

"FREEZ" indicates that the STOPWATCH has been put to a manual halt.

P19

12. Display of training times within preset target range training zones.

With your VDO HC 12.6 you determine your upper and lower pulse limits Limits setup see paragraph 9.

Training times within preset target range training zones are only registered if

• the computer is switched on,

• the chestbelt sender is transmitting pulse signals,

• the STOPWATCH has not been put to a manual halt,

Training times within preset target range training zones are called up by pressing the PULSE button. TIME ABOVE indicates the time your pulse has been above the preset upper limit, i.e. 12:15 mm:ss

In case the display alternately shows "FREEZ" and the actual value, the STOPWATCH has been put to a manual halt. Hence, registering training times within target zones has been interrupted. "FREEZ" indicates that status.

TIME IN indicates the time your pulse / heart rate is within the preset upper and lower limit window, i.e. 1:14:40 h:mm:ss This window is your desired target range zone in which you should be most of the time to achieve optimum results. Same here, "FREEZ" indicates the STOPWATCH has been put to a manual halt and time zone registering is interrupted.

TIME BELOW indicates the time your pulse has been below the preset lower limit, i.e. 8:40 m:ss In case the display alternately shows "FREEZ" and the actual value, the STOPWATCH has been put to a manual halt.

13. BEEPER activating / deactivating

Should your actual pulse be either higher than the preset upper limit or lower than the preset lower limit, an audible alarm (BEEPER) warns you about that status.

The beeper may be activated or deactivated. ON / OFF BEEPER Press PULSE for 3 sec The beeper icon emerges on or disappears from the display.

12.6

14. Troubleshooting

This chart outlines possible malfunctions, their causes and removal.

12.6

malfunctions most likely cause removal solutions irregular LCD readout (i.e. after battery change) computer software is not running smoothly press AC-button at the rear of computer head

no speed display check for proper distance between sensor readjust sensor and magnet

display fades or disappears battery in computer empty check battery and replace if necessary.

no pulse display computer in sleep-mode, receiver not activated press any button to activate receiver

no average pulse display - stopwatch not running, stopwatch start stopwatch or take off manual halt no time display for training zones manually arrested

and magnet cable from sensor to computerhead broken check cable and replace if necessary computerhead is incorrectly twisted onto place computerhead on handlebar holder handlebarholder and twist until detent (CLICK) no wheelsize value entered enter wheelsize number

temperatures below -15°C (40°F) dull Back in normal temperatures, display display readout picks up working correctly.

chestbelt battery empty check battery and replace if necessary. chestbelt electrodes not moistened moisten the electrodes with water or saliva distance from computer to chestbelt is too big reduce distance

to reset

15. Warranty

We warrant VDO HC 12.6 (chestbelt, sensor, computer head and handlebar holder) to the original purchaser for five years from date of purchase against defects in material and workmanship. This does not cover the batteries, cables and defects resulting from normal wear and tear, improper care, accidents, abuse or alteration.

Please take care to retain your receipt of purchase. In case of legitimate complaints, you are entitled to receive a comparable replacement model. Due to possible model changes, your model might not be

available any more. You may contact your retailer or store where you purchased your VDO HC 12.6 or send the computer directly to us:

CYCLE PARTS GMBH Grosse Ahlmuehle 33 76865 Rohrbach / Germany

In case of technical queries, call our consumer-service-hotline Tel.+49-6349-9635-10. Technical specifications of VDO HC 12.6 are subject to change.

12.6

16. Technical data

dimensions computer width 42 x ht 52 x depth 14mm weight 40(g)

12.6

chestbelt weight 80(g) handlebar holder weight 30(g) batteries computer 3V, type 2032

radio frequency chestbelt 5,2 Khz (POLAR-compatibel) chest belt (transmitter) range 0.75 m operating temperature range LCD-display -15 °C to +80 °C speed measuring range 2,5 km/h minimum 120 km/h maximum trip distance counter up to 999,99 km or mi NAVIGATOR up to 999,99 km or mi odometer 1 up to 99.999 km or mi odometer 2 TOTODO odometers 1+2 up to 199.999 km or mi wheelsize 100 mm minimum 3999 mm maximum pulse measuring range 40 minimum 240 maximum

17. Contents

1 computer head 1 handlebar holder with sensor, cable and screw 1 rubber shim for sensor mount 1 spoke magnet 1 chestbelt plus Elastic strap 5 cable ties 1 battery 3 V Type CR 2032 1 installation and operation manual

chestbelt 3V, type 2032

Vdo HC12.6 User Manual [ru]

Specifications and Main Features

Frequently Asked Questions

User Manual