UNI-T UTD2025 series, UTD3025 series User Manual

Uni-Trend Technology (Chengdu) Ltd

.

Page1of

27

Communica

tion & Control So

ftware for

UTD20

25

_3025Series Oscilloscopes

User

Manual

Document No. SYSC

-0-

10010

8

January

20

10

Digital Storage

Oscilloscope

Communication

&

Control

Software

User Manual and Installation Instructions

Uni-Trend Technology (Chengdu) Ltd

.

Page2of

27

Communica

tion & Control So

ftware for

UTD20

25

_3025Series Oscilloscopes

User

Manual

Table of Contents

Chapter 1

Installation of the

Digital Storage

O

scilloscope

communication and control software ………

……

.…3

1.1

Hardware requirements …………………………………………..

3

1.2

Installing the software ……………………………………………

3

1.3

Running the software …………………………………………….

7

1.4

Installing the USB driver …………………………………………

8

Chapter 2

Getting to know your

Digital Storage

O

scilloscop

e

communication

and control software

…

11

2.1

The control panel …………………………..……………………...

11

2.2

Main menu ……………………………………………..………….

122.3

Cont

rol panel instructions ………………………………...……….

182.4

Transmission interface and explanatory notes ………………...…..

19

Chapter 3

Operation guide for the

Digital Storage

O

scilloscop

e

communication

and control software …

2

1

3.1

USB interface controls ……………………

……………………….

223.2

Ethernet (LAN) interface controls ………………………………...

243.3

GPIB interface controls …………………………………………...

2

5

Chapter 4

System Prompts and Trouble

-

shooting ……………..

2

6

4.1

System prompts …………………………………………………...

264.2

Troubleshooting ………

……………

..

…………………………….

2

6

Uni-Trend Technology (Chengdu) Ltd

.

Page3of

27

Communica

tion & Control So

ftware for

UTD20

25

_3025Series Oscilloscopes

User

Manual

Chapter 1 Installation of the oscilloscope communication

and control software

1.1

Hardware requirements

Equipment requirements

Minimal.

Oscilloscope

UTD2025_3025

Series Digital Storage Oscilloscope.

Compute

r

Windows 2000/XP/Vista, 128 MB RAM, 16x CD

-

ROM or better (Vista users

please refer to its individual hardware requirements), SVGA display or better.

Connection cable

USB A

-

B cable or RJ45 net cable or GPIB communication cable.

1.2

Installing the software

Your

UTD2025_3025

Series Digital Storage Oscilloscope (“Oscilloscope”) comes with an oscilloscope

communication and control software (contained in the CD

-

Rom supplied with your oscilloscope).

Alternatively, you can download the software online :

File name

:

UTD2025_3025

oscilloscope communication and control software.

Installation :

Step one :

Insert the CD

-

rom supplied with your oscilloscope into the CD

-

Rom drive of the computer.

Wait for the system to read and find the oscilloscope communication and

control software

contents (Fig. 1

-

1).

Fig 1-1

Note :

1.

The installation pack downloaded online must be unzipped before application.

2.

The software supports Windows 2000, Windows XP and Vista operat

ing systems. On Vista only

USB2.0 communication protocol is supported.

Step two :

Double left click the mouse to run the oscilloscope communication and control software

installation as shown in Fig 1

-1.The installation wizard for the oscilloscope communi

cation and control software will pop up, as

shown in Fig. 1

-

2.

Uni-Trend Technology (Chengdu) Ltd

.

Page4of

27

Communica

tion & Control So

ftware for

UTD20

25

_3025Series Oscilloscopes

User

Manual

Fig 1-2

Step three :

Read the prompt in Fig 1

-

2 then click the [NEXT (

N

)] button to enter the next step, as shown in

Fig 1-3.

Fig 1-3

Step four :

In Fig 1

-

3, enter your user name

and company name, then click the [NEXT (

N

)] button to enter

the next step, as shown in Fig 1

-

4.

Uni-Trend Technology (Chengdu) Ltd

.

Page5of

27

Communica

tion & Control So

ftware for

UTD20

25

_3025Series Oscilloscopes

User

Manual

Fig 1-4

Step five :

In Fig 1

-

4, click the [CHANGE (

H

) …] button to specify the installation path of the software,

then click [NEXT (

N

)]. You can also click [

NEXT (

N

)] directly to use the default path. Enter

the screen shown in Fig 1

-5.Fig 1-5

Step six :

In Fig 1

-

5, after confirming the message is correct, click [NEXT (

N

)] to enter the front page for

automatic installation, as shown in Fig

1-6.

Uni-Trend Technology (Chengdu) Ltd

.

Page6of

27

Communica

tion & Control So

ftware for

UTD20

25

_3025Series Oscilloscopes

User

Manual

Fig1-

6

Step seven :

When automatic installation is complete and the box shown in Fig 1

-

7 pops up, click the

[FINISH (

F

)] button. Your oscilloscope communication and control software is now

successfully installed on your computer and ready for use.

Fig 1-7

To return to the previous installation guide interface, click [BACK (

B

)] on any installation guide page.

To stop installation, press [CANCEL (

C

)] on any installation guide page.

Uni-Trend Technology (Chengdu) Ltd

.

Page7of

27

Communica

tion & Control So

ftware for

UTD20

25

_3025Series Oscilloscopes

User

Manual

1.3 Running the software

When installation of the oscilloscope communicati

on and control software is complete, you can run it on your

computer in two ways.

1.

When installation of the oscilloscope communication and control software is complete, an short

-

cut icon is

automatically created on the computer desktop, as shown in Fig

1-8. To run the software, simply double left

click the icon in Fig 1

-

8 with your mouse.

Fig 1-8

2.

Alternatively, you can run the software by going through START



Programme



Digital storage

oscilloscope



DSO, as shown in Fig 1

-

9.

Fig1-

9

Uni-Trend Technology (Chengdu) Ltd

.

Page8of

27

Communica

tion & Control So

ftware for

UTD20

25

_3025Series Oscilloscopes

User

Manual

1.4 Installing the USB driver

If you are using the oscilloscope’s USB device port for software communication and control, the USB driver must

be installed after installation of the oscilloscope communication and control software is complete. Fo

llow the

steps below :

1.

There is a USB device port on the rear panel of your

UTD2025_3025

Series Digital Storage Oscilloscope.

With the supplied USB A

-

B cable, you can connect the USB device port to the USB Host port of the

computer and obtain power supp

ly for the oscilloscope.

2.

After checking that connection and power supply are normal, power on the digital storage oscilloscope.

When the operation status screen appears, a prompt will appear at the right bottom corner to indicate “New

hardware DSO dete

cted”, as shown in Fig 1

-

10.

Fig 1-10

Next, an icon will be created for the “New hardware DSO detected”, as shown in Fig 1

-

11.

Fig 1-11

Then a “hardware update wizard” dialog box will pop up on the desktop, as shown in Fig 1

-

12.

Fig 1-12

Uni-Trend Technology (Chengdu) Ltd

.

Page9of

27

Communica

tion & Control So

ftware for

UTD20

25

_3025Series Oscilloscopes

User

Manual

3.In the new hardware wizard dialog box in Fig 1

-

12, select the “automatic software installation

(recommended) (

I

) option, then click [NEXT (

N

)] to enter the automatic driver search and installation page, as

shown in Fig 1

-

13.

Fig 1-134.As shown in Fig

1-13, the hardware installation wizard of your digital storage oscilloscope begins automatic

searching and installing the USB driver for the oscilloscope communication and control software. When

installation is complete the dialog box shown in Fig 1

-

14 pop

s up.

Fig 1-14

Uni-Trend Technology (Chengdu) Ltd

.

Page10of

27

Communica

tion & Control So

ftware for

UTD20

25

_3025Series Oscilloscopes

User

Manual

5.

In Fig 1

-

14, click the [FINISH (

F

)] button. Your USB driver is now installed, and instant communication and

control are enabled between the oscilloscope and the software. Please read “3.1 USB Interface Controls” in

“Chapter 3 : Operat

ion guide for the oscilloscope communication and control software” of this booklet prior to

operation.

Uni-Trend Technology (Chengdu) Ltd

.

Page11of

27

Communica

tion & Control So

ftware for

UTD20

25

_3025Series Oscilloscopes

User

Manual

Chapter 2 Getting to know your oscilloscope communication

and control software

2.1 The control panel

After the o

scilloscope communication and control software is activated, a display panel similar to the digital

storage oscilloscope operation interface will pop up. This is the virtual oscilloscope control panel. When

transmitting data, you can observe the current wa

veform displayed by the oscilloscope on the virtual control panel.

This interface also features menus, controls and knobs for accessing waveform and channel parameters (please

disable the “data transmission” function before using the menus to access inform

ation). Please see below for

detailed operation instructions.

Fig 2-1

Menu

Virtual display

Channel selection

Transfer indicator

Channel status

Real-time control

Range indicator

Virtual control

panel

Uni-Trend Technology (Chengdu) Ltd

.

Page12of

27

Communica

tion & Control So

ftware for

UTD20

25

_3025Series Oscilloscopes

User

Manual

2.2 Main menu

Fig 2-1 shows four menus under the main menu on the top left corner : document, function, waveform refresh and

help

. Their operation instructions are as follows :

1.

Document

Load :

This means saving the oscilloscope communication and control software to the computer hard

disk or other storage media, or save it in a waveform file on any mobile storage media by using

the long save function of the oscilloscope save menu, and then open the saved waveform on the

virtual display panel with the “Load” feature.

Note :

When storing a waveform from the digital storage oscilloscope to a mobile USB device,

storage mode of the

oscilloscope must be set to “long storage” to load the waveform onto the

computer software. To set “long storage”, use the STORAGE button on the front panel of the

oscilloscope : STORAGE



Type : WAVEFORM



NEXT



Disk (USB)



Storage

depth (Long storage).

Save :

This means saving the waveform currently on the virtual display panel to a computer or other

storage equipment. Select “Document”



“Save” and save it on the hard disk or mobile external

hard disk in *.dat format. Assign any file name you like.

R

ecord :

Enable the “data transmission” function and select “Document”



“Record”. A prompt box

shown in Fig 2

-

2 will pop up on the virtual display panel and recording of the virtual display

waveform begins. The recording prompt box shows the current wavefo

rm recording progress.

To pause recording, simply click the “pause” button. To resume, click the “continue” button and

recording will resume from the point where it was paused.

The dialog box in Fig 2

-

3 appears when you close the waveform recording functi

on or recording

has reached the maximum number of data screens. Click “YES” in Fig 2

-

3 to save it in *.dat

format on the computer hard disk or other storage device. If you wish to abandon recording,

press “NO” as shown in Fig 2

-

3. The waveform recording fu

nction can record up to 2000

screens of data.

Fig 2-2

Fig 2-3

Uni-Trend Technology (Chengdu) Ltd

.

Page13of

27

Communica

tion & Control So

ftware for

UTD20

25

_3025Series Oscilloscopes

User

Manual

Playback :

After stopping “data transmission”, you can play back the waveform recorded and saved on the

computer hard disk or other mobile storage med

ia. Simply select “Document”



“Playback”.

You can play back a waveform in dynamic or static mode.

Dynamic

playback :

Select “Document”



“Playback”



“Dynamic playback”. The waveform playback loading

interface in Fig 2

-

4 will pop up. Specify the search

area to locate the storage path of the

recorded waveform, select the recorded waveform document you require, then click the [Load]

button. The recorded waveform will be played continuously on the virtual display with the

current playback progress.

Static

playback :

Select “Document”



“Playback”



“Static playback”. The waveform playback loading

interface in Fig 2

-

4 will pop up. Specify the search area to locate the storage path of the

recorded waveform, select the recorded waveform document you require

, then click the [Load]

button. Fig 2

-

5 will now appear. By using the “manual playback” button, you can play back the

recorded waveform screen by screen. Alternatively, enter the required screen number in the

screen number display field and press “ENTER”.

Your specified screen will be displayed. To

close the static playback function, click the “close static playback” button.

Fig 2-4

Fig 2-5

Manual playback button

Field for entering the number of screens

Uni-Trend Technology (Chengdu) Ltd

.

Page14of

27

Communica

tion & Control So

ftware for

UTD20

25

_3025Series Oscilloscopes

User

Manual

Print

preview :

After

completing the “data transmission” or “transmission interface” task, select “Document”



“print preview” to preview the waveform or interface (as the case may be) before printing.

Waveform :

The preview waveform is the last screen of waveform data uploade

d from the oscilloscope to

the communication and control software after “data transmission” is completed, or the

waveform on the computer hard disk or mobile USB device which is downloaded to the

software with the “load” function.

Depending on the n

umber of channels working at the time of data transmission, you can select

the channel mode on the waveform preview interface with the selection function of the menu.

When uploading with two channels, you can select “single channel” (CH1, CH2), “two

channe

ls” (CH1 & CH2, CH1 & Math, CH2 & Math) or “all” to preview the waveform. To quit

the preview screen, click the exit button.

Interface :

The preview interface is the last screen uploaded by the oscilloscope to the computer after the

“transmission interfac

e” is closed.

Printing :

When “data transmission” is complete, select “Document”



“Print” to print the waveform or

the interface.

Waveform :

The printed waveform is the last screen of waveform data uploaded from the oscilloscope to the

communication and

control software after “data transmission” is completed, or the waveform on

the computer hard disk or mobile USB device which is downloaded to the software with the

“load” function.

Interface :

The print interface is the last screen uploaded by the osci

lloscope to the computer after the

“transmission interface” is closed.

Exit :

After the “data transmission” or “transmission interface” task is complete, select “Document”



“exit” to quit the oscilloscope communication and control software.

2.

Function

s

All sub

-

menus under the FUNCTION menu can be operated only when the “data transmission” or “transmission

interface” task is complete.

◆

Mathematics functions : When this menu is clicked, a mathematics function dialog box will pop up to enable

“mathematics selection” or “FFT mathematics”, as shown in Fig 2

-6.

Uni-Trend Technology (Chengdu) Ltd

.

Page15of

27

Communica

tion & Control So

ftware for

UTD20

25

_3025Series Oscilloscopes

User

Manual

Fig 2-6

Mathematics selection :

You can

select the mathematical relation between signal sources A and B. There

are four mathematical relations : +,

-

, x, ÷.

Signal source selection :

There are A and B signal sources. You can set them up as CH1 or CH2 channel

signals respectively.

FFT function

selection :

You can switch between “Rectangle”, “Hanning”, “Hamming” and “Blackman”.

FFT signal source selection :

You can select CH1 or CH2.

◆

Remote control :

You can operate the digital storage oscilloscope on remote control with the

communication and control software. In the remote control mode, the computer screen will display a virtual

instrument control panel which is fundamentally the sa

me as the oscilloscope control panel, as shown in

Fig 2-7.

Uni-Trend Technology (Chengdu) Ltd

.

Page16of

27

Communica

tion & Control So

ftware for

UTD20

25

_3025Series Oscilloscopes

User

Manual

Fig 2-7

The sign of every button or knob on the virtual control panel is identical to that on the oscilloscope control panel.

You can click the same buttons

to operate the corresponding functions. To use the virtual control panel efficiently,

you must be familiar with all function menus as well as the current status of the oscilloscope.

Note : You can only operate the digital storage oscilloscope with the vir

tual control panel. Waveform observation

or screen display function is not available. You cannot operate the “remote control” and “transmission

interface” tasks simultaneously.

◆

Data table :

This shows the function relation between the voltage and time o

f the sampling point of the

waveform currently on display, i.e. V=F(t).

Fig 2-8

Virtual control

panel

Channel

indication

Uni-Trend Technology (Chengdu) Ltd

.

Page17of

27

Communica

tion & Control So

ftware for

UTD20

25

_3025Series Oscilloscopes

User

Manual

When you click the “save data” option under “function selection” on this screen, a data table storage interface will

pop up, as shown in Fig 2

-

9. Select the data saving pa

th in the “save to” path selection field, enter the document

name in the name field, then click to save. Current data in the table can be saved locally as an EXCEL file. To quit

the data table test, click “exit”.

Fig 2-9

◆

Parameter measurement :

This shows all the parameter values of the waveform currently on display in the

selected channel.

Select channel :

You can select CH1 or CH2.

Start/pause transmission :

“Start transmission” means beginning to transmi

t data. “Pause transmission” means

stopping transmission.

Fig 2-10

Select the

path

Enter the

document

Uni-Trend Technology (Chengdu) Ltd

.

Page18of

27

Communica

tion & Control So

ftware for

UTD20

25

_3025Series Oscilloscopes

User

Manual

3.

Waveform refresh

Single refresh :

This is a single waveform trigger. The acquired waveform display is stored on the display

panel of the virtual control panel.

Waveform time inte

rval setup :

To set up the time interval for waveform refresh.

4.

Help

This menu shows the version of the oscilloscope communication and control software.

2.3 Control panel instructions

Keys on the control panel of the oscilloscope communication an

d control software (Fig 2

-

1) function as

follows

:

Channel status

:

This indicated the current control status of the digital storage oscilloscope.

During “data transmission”, this status bar indicates the current control status of the oscilloscope. This

bar

changes with the actual control status of the oscilloscope but you cannot control the current status of the

oscilloscope with this bar.

CH1 :

Coupling method (DC, AC, GND); Bandwidth suppression (On, Off); Filter type (low

-

pass,

high-pass, band

-

pass,

band

-

stop); Digital filter (when the indicator light comes on the function is ON, when

the indicator light goes off the function is OFF); Reverse (when the indicator comes on the function is ON,

when the indicator light goes off the function is OFF); Prob

e (1X, 10X, 100X, 1000X).

CH2 :

Coupling method (DC, AC, GND); Bandwidth suppression (On, Off); Filter type (low

-

pass,

high-pass, band

-

pass, band

-

stop); Digital filter (when the indicator light comes on the function is ON, when

the indicator light goes of

f the function is OFF); Reverse (when the indicator light comes on the function is

ON, when the indicator light goes off the function is OFF); Probe (1X, 10X, 100X, 1000X).

Sampling method :

Random; Real

-

time; SCAN

Interpolation :

Yes; No

Current activa

ted channel :

MATH; CH1; CH2

Channel selection :

CH1; CH2; MATH

Bias adjustment :

Vertical; Horizontal

Range adjustment :

Voltage range; Time base range

Real-time Control :

Equipment selection (USB, LAN, GPIB); ON/OFF (when the indicator light comes on

the function is ON, when the indicator light goes off the function is OFF); Data transmission (when the

indicator light comes on the function is ON, when the indicator light goes off the function is OFF);

Transmission interface (when the indicator light c

omes on the function is ON, when the indicator light goes

off the function is OFF).

Uni-Trend Technology (Chengdu) Ltd

.

Page19of

27

Communica

tion & Control So

ftware for

UTD20

25

_3025Series Oscilloscopes

User

Manual

Reverse mathematics function :

Indicator on means reverse mathematics function is in process. Indicator

off means reverse mathematics function is not in process.

Mathema

tics function :

Select mathematics functions with the function menu in the menu bar.

Auto Refresh :

Set up the refresh time interval with the waveform refresh menu in the menu bar.

Refresh time :

Set up refresh time while performing auto refresh.

2.4 T

ransmission interface and explanatory notes

To select USB or LAN to control communication, click the “transmission interface” button on the virtual control

panel of the communication and control software to enter the “transmission interface” operation scr

een. Here, you

can enable remote interface transmission as shown in Fig 2

-

11. The virtual display panel shows the waveform and

interface of the oscilloscope. The virtual control panel is a virtual operation panel of your digital storage

oscilloscope. You c

an control and operate the unit from here.

Fig 2-11

Menu :

Function selection :

Saving and exiting screen

Save :

Select “Single” as in Fig 2

-

11 to save the waveform and screen on the virtual

display panel in *.bmp f

ormat on the computer hard disk or mobile USB device.

Exit :

Quit the remote control transmission interface mode.

Serial :

When “serial” is selected, the waveform on the virtual display panel will be updated in real

time and in synchronization with the

waveform stored by the oscilloscope. In this mode,

data volume is sizeable and control response is slower.

Single :

When “single” is selected, the waveform on the waveform display screen is not displayed in

synchronization with the waveform stored by the

oscilloscope. In this mode, data volume is

limited and control response is faster.

Close :

Close the transmission interface and return to the main control panel (Fig 2

-

1).

Vi

rtual display panel

Virtual control panel

Operation mode

Uni-Trend Technology (Chengdu) Ltd

.

Page20of

27

Communica

tion & Control So

ftware for

UTD20

25

_3025Series Oscilloscopes

User

Manual

Chapter 3 Operation guide for the oscilloscope communication

and control so

ftware

By now you should have grasped the basic structure, menu options and functions of the oscilloscope

communication and control software. In the following pages you will find more detailed instructions on how to

operate the software. In this chapter,

we will give guidance on USB, LAN

and

GPIB control modes.

To enjoy optimal software performance, we recommend you to read the oscilloscope user manual and this chapter

to familiar

with application.

After installing the software and driver properly, conn

ect the cable to the USB A

-

B communication port. Power on

the oscilloscope and activate the software. The software control panel shown in Fig 3

-

1 will appear on your

computer screen.

Fig 3-1

Uni-Trend Technology (Chengdu) Ltd

.

Page21of

27

Communica

tion & Control So

ftware for

UTD20

25

_3025Series Oscilloscopes

User

Manual

3.1 USB interface controls

After installing your commu

nication and control software, please install the driver before using the USB

communication mode for the first time. For instructions please refer to “Chapter 1.4 : Installing the USB driver”.

When installation is complete, run the software and enter the s

creen shown in Fig 3

-1.After selecting USB in the equipment selection option, operate as follows :

1.

Select “USB” in the equipment selection option on the virtual control panel.

2.

Click the [Equipment ON/OFF] button to turn it “ON”. The indicator lig

ht is green. When the button is

turned “OFF”, the indicator light will go off, as shown in Fig 3

-2.Fig 3-2 ON/OFF status display of the equipment selection button

3.

Click the [Data Transmission] button to turn it on. When the indic

ator light comes on the function is ON.

When the indicator light goes off the function is OFF, as shown in Fig 3

-

3. When data transmission is on,

you can operate the digital storage oscilloscope with the buttons and knobs on the control panel. The

paramete

rs and setups of the virtual control panel will change accordingly.

Fig 3-3 ON/OFF status display of the data transmission button

4.

When data transmission is complete, Click the [Data Transmission] button again to tu

rn it off.

During data transmission, you cannot operate the oscilloscope with the software. The function keys on the

virtual control panel are disabled but they continue to indicate the current status of the oscilloscope.

Uni-Trend Technology (Chengdu) Ltd

.

Page22of

27

Communica

tion & Control So

ftware for

UTD20

25

_3025Series Oscilloscopes

User

Manual

5.

Enter the “transmission int

erface” and click the [Transmission Interface] button. The indicator light comes

ON. Transmission interface mode is now enabled, as shows in Fig 3

-4.Fig 3-46.On the virtual control panel in Fig 3

-

4, you can oper

ate your oscilloscope with different buttons as instructed

by the oscilloscope user manual. Select “Serial” on the above screen so the oscilloscope can transmit the

oscilloscope screen to the virtual display panel in real time. When “Single” is selected, t

he virtual display

panel will only show the first transmission interface.

Note :

In serial mode when transmission volume is high, response of the software is relatively slow. In single

mode, however, response is quick as there is only one transmission and

data volume is low.

7.

When operation is complete press [CLOSE] to close this screen.

Note :

The “data transmission”, “remote control” and “transmission interface” functions cannot be operated

simultaneously.

Uni-Trend Technology (Chengdu) Ltd

.

Page23of

27

Communica

tion & Control So

ftware for

UTD20

25

_3025Series Oscilloscopes

User

Manual

3.2 Ethernet (LAN) interface controls

T

he Ethernet port is a dedicated interface module of

UTD2025_3025

Digital Storage Oscilloscopes. This TCP/IP

protocol embedded module can provide direct Ethernet connection to a

UTD2025_3025

series oscilloscope. After

installing the communication and contro

l software, you can operate your oscilloscope on remote control through

LAN or the Internet. As it supports concurrent visit by multiple users, there are no geographical and users

restraints and you can carry out network and remote testing as well as measu

ring.

With the optional UT

-

M01 (for

UTD20

25

models) or UT

-M05

(for

UTD30

25

models) Ethernet module, you can

operate the oscilloscope through the LAN interface as follows :

1.

Select “LAN” in the equipment selection option on the real

-

time control panel

.2.When “LAN” is selected, the dialog box in Fig 3

-

5 will pop up.

Fig 3-5

Enter the DSO IP address in this box. The IP addresses set in the software and the communicated oscilloscope

must be the same, otherwise c

ommunication between the oscilloscope and the software cannot be established.

Please refer to the oscilloscope user manual for operation instructions. Access sub

-

menu page 3 by pressing

[UTILITY]



LAN on the oscilloscope control panel for TCP/IP protocol

setup. You should set up the IP address,

netmask and default gateway in LAN. In the same network, the IP address of every individual digital storage

oscilloscope is unique and must not conflict with the IP address of any other equipment (in

-

network IP add

resses).

3.

For other operation instructions refer to steps 2,

3,4,5,

6 and 7 for “

USB interface controls” in this chapter.

Note

:

When using the LAN interface, you can operate the oscilloscope by remote control via LAN or the Internet.

Mapping feature

of the router must be enabled and the public network address of your company should provided.

Uni-Trend Technology (Chengdu) Ltd

.

Page24of

27

Communica

tion & Control So

ftware for

UTD20

25

_3025Series Oscilloscopes

User

Manual

3.3

GPIB interface controls

The GPIB port is a dedicated interface module of

UTD30

25

Series Digital Storage Oscilloscopes. After installing

the communication

and control software, you can carry out system operation and control your oscilloscope

through the GPIB interface. You can create an automatic testing system simply, quickly and efficiently, and carry

out testing and measuring.

With the optional UT

-

M02 e

xtension

module, you can operate your

UTD30

25

oscilloscope through the GPIB

interface as follows

:1.Select “GPIB” in the equipment selection option on the real

-

time control panel.

2.

When “GPIB” is selected, the dialog box in Fig 3

-

6 will pop up.

Fig 3-6

Enter the GPIB device address in this box (range

: 1-30). The GPIB device addresses set in the software and the

communicated oscilloscope must be the same, otherwise communication between the

oscilloscope and the

software cannot be established.

Access sub

-

menu page 3 by pressing [UTILITY]



GPIB on the oscilloscope control panel for GPIB device

address setup.

There must not be two identical GPIB device addresses on one GPIB main line.

3.For other operation instructions refer to steps 2 and 3 for “

USB interface controls” in this chapter.

Note :

When using the GPIB interface, the “transmission interface” feature is disabled.

Uni-Trend Technology (Chengdu) Ltd

.

Page25of

27

Communica

tion & Control So

ftware for

UTD20

25

_3025Series Oscilloscopes

User

Manual

Chapter 4

System Prompts and Trouble

-

shooting

4.1 System p

rompts

Time out prompt : Check the communication interface configuration. See whether the equipment is properly

connected and check software driver update.

SCAN prompt : SCAN will perform single transmission. Please carry out single refresh. Continue?

A

re you sure you want to exit Virtual Instrument? A prompt to ask you if you wish to close the software.

4.2 Troubleshooting

1.

If the system prompts you to check serial or USB configuration when you enter [Equipment ON/OFF], take

the following steps :



Check whether the oscilloscope power plug is properly connected.



Check whether oscilloscope ports match the communication and control software setups.



Check whether the cable connection between module and PC is in order.



Ensure the USB driver

is properly installed.



After carrying out the above checks, restart the software and oscilloscope to continue operation.

2.

If you are unable to update the software driver, take the following steps :



Right click the box on your computer desk

-

top as sh

own in Fig 4

-

1 to activate the right

-

click menu in Fig

4-2.

Fig 4

-1Fig 4

-

2

Uni-Trend Technology (Chengdu) Ltd

.

Page26of

27

Communica

tion & Control So

ftware for

UTD20

25

_3025Series Oscilloscopes

User

Manual



In Fig 4

-

2, select “attribute” and right click to pop up Fig 4

-3.Fig 4-3Select “hardware” in Fig 4

-

3. Fig 4

-

4 is displayed.

Fig 4-4

Uni-Trend Technology (Chengdu) Ltd

.

Page27of

27

Communica

tion & Control So

ftware for

UTD20

25

_3025Series Oscilloscopes

User

Manual



Select “equipment manager D” in Fig 4

-

4. Fig 4

-

5 pops up.

Fig 4-5In Fig 4

-

5, delete “digital storage oscilloscope” in “Un

iversal serial main line controller” to restart the

oscilloscope. Select automatic driver update to complete the update process.

Note :

When the communication and control software is communicating with the digital storage oscilloscope,

you cannot connect

both the network cable and USB device cable to the oscilloscope ports, and do not

remove the cable to disconnect during communication.