Uniden UIP300G User Manual

UIP300G

(H.323 IP Phone)

Guide

Administrator

Preface

This Document

This document provides instructions to user for operating the UIP300G IP Phone.
This manual provides a detailed description of the telephone, LCD displays and
features. Basic telephone operations and features are explained. Setup and
configuration instructions are also provided.

*Uniden

® is a registered trademark of Uniden America Corporation.

1

Regulatory Information

FCC Part 15

Complies with the limits for a Class B computing device pursuant to Subpart B of
Part 15 of FCC Rules.

U.L. Compliance

This equipment complies with Underwriters Laboratories Standard U.L. 60950.

Repairs

NO REPAIRS CAN BE DONE BY THE CUSTOMER

Hearing-Aid Compatibility

The equipment is hearing-aid compatible.

The act of monitoring or recording telephone conversations under certain
circumstances may violate federal or state statutes. Consultation with your legal
counsel prior to engaging in such practices would be advisable.

Industry Canada (ICES-003)

This class B digital apparatus complies with Canadian ICES-003.

Users should not attempt to make such connections themselves, but should
contact the appropriate electric inspection authority, or electrician, as appropriate.

2

Important Safety Considerations

When using this product, basic safety precautions should always be followed to
reduce the risk of fire, electrical shock, and injury to persons, including the following:

1 Read and understand all instructions.
2 Follow all warnings and instructions marked on the product.
3 Unplug this product from the wall outlet before cleaning. Do not used liquid

cleaners or aerosol cleaners. Use a dry cloth for cleaning.

4 Do not use this product near water; for example, near a sink or in a wet area.
5 Do not place this product on an unstable cart, stand, or table. The telephone can

fall, causing serious damage to the unit.

6 Slots and openings in the cabinet and the back or bottom are provided for ventilation. To

protect the product from overheating, these openings must not be blocked or covered.
This product should never be placed near or over a radiator or heat register. This product
should not be placed in a built-in installation unless the proper ventilation is provided.

7 This product should be operated only from the type of power source indicated on

the marking label. If you are not sure of the type of power supply to your home,
consult your dealer or local power company.

8 Do not allow anything to rest on the power cord. Do not locate this product where

the cord will be damaged by people walking on it.

9 Do not overload wall outlets and extension cords, as this can result in the risk of

fire or electrical shock.

10 Never push objects of any kind into this product through cabinet slots, as they may

touch dangerous voltage points or short out parts that could result in a risk of fire
or electrical shock. Never spill liquid of any kind on the product.

11 To reduce the risk of electric shock, do not disassemble this product. Contact

qualified service personnel when some service or repair work is required. Opening
or removing covers may expose you to dangerous voltages or other risks. Incorrect
reassembly can cause electric shock when the appliance is subsequently used.

12 Unplug this product from the wall outlet and refer servicing to qualified service

personnel under the following conditions:
A When the power supply cord is damaged or frayed.
B If liquid has been spilled onto the product.
C If the product has been exposed to water or rain.
D If the product does not operate normally when following the operating

instructions. (Adjust only those controls that are covered by the operating
instructions. Improper adjustment of other controls can result in damage, and

will often require extensive repair work by a qualified technician.)
E If the product has been dropped, or the cabinet has been damaged.
F If the product exhibits a distinct change in performance.

13 Uniden works to reduce lead content in our PVC coated cords in our products

and accessories.
Warning: The cords on this product and/or accessories contain lead, a chemical
known to the State of California to cause birth defects or other reproductive harm.

Wash hands after handling.

3

Important Electrical Considerations

Unplug all electrical appliances when you know an electrical storm is
approaching. Lightning can pass through your household wiring and
damage any device connected to it. This product is no exception.

WARNING! Please do not attempt to unplug any appliance during an

electrical storm.

The FCC Wants You to Know

Changes or modifications to this product not expressly approved by the
party responsible for compliance could void the user’s authority to operate
the equipment.

This equipment has been tested and found to comply with the limits for a Class
B digital device pursuant to part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, and
may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one or more of
the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and the receiver.

• Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

AC Adapter

The UIP300G is intended to be supplied by AD300 a UL Listed direct plug-in
power unit marked “Class 2” or “LPS” or “I.T.E. Power Supply” and rated 48VDC,

0.25A output. When you use an AC Adapter, use and AC outlet without a switch

to interrupt power, and do not use an outlet controlled by a wall switch.

Place the power cord so that it does not create a trip hazard, or where it could
become chafed and create a fire or other electrical hazards.

4

Table of Contents

Chapter 1 Product Description

General Information ..........................................................................................8

Standard Features of the Telephone ................................................................9

VoIP Specific Features ......................................................................................9

General Features ..............................................................................................9

Control and Functions of the Telephone ........................................................10

Function Keys..................................................................................................10

LED Status ......................................................................................................10

Specifications ..................................................................................................11

Physical Interface........................................................................................11

Power Supply..............................................................................................11

Speaker ......................................................................................................11

Optional & Replacement Equipment ..............................................................12

Chapter 2 Installation and Basic Setup Instructions

General Information ........................................................................................13

Attaching the Footstand to the Telephone ......................................................13

Connecting the Telephone ..............................................................................14

Quick Setup Procedure ..................................................................................15

Chapter 3 Basic Operations

General Information ........................................................................................22

Telephone Operations ....................................................................................22

Standby ......................................................................................................22

Originating (Outgoing) Calls ......................................................................23

Using the Handset ................................................................................23

Using the Phone Book ..........................................................................23

Using On-Hook Dialing ..........................................................................24

Receiving Calls ..........................................................................................24

Answering Calls Using the Handset ......................................................24

Answering Calls Handsfree....................................................................24

2-Line Operation ........................................................................................24

Accessing Line 1....................................................................................24

Accessing a Line Using the Line Key ....................................................25

Volume Control................................................................................................25

5

Handset Volume Control........................................................................25

Speakerphone Volume Control..............................................................26

Headset Volume Control........................................................................26

Ringer Volume Control ..........................................................................26

Feature Operations ........................................................................................27

Handsfree ..................................................................................................27

Speakerphone........................................................................................27

Headset..................................................................................................27

Receiving a Call Using Handsfree ........................................................27

Phone Book ................................................................................................27

Programmable and Fixed Function Keys ..................................................28

Speed Dial..............................................................................................28

Do Not Disturb (DND) ............................................................................28

Voice Mail ..............................................................................................28

Redial ....................................................................................................29

Mute ......................................................................................................29

Hold........................................................................................................29

Transfer..................................................................................................30

Conference ............................................................................................30

Call Waiting ............................................................................................30

Chapter 4 Setup Menu

General Information ........................................................................................31

Basic Setup Menu Options..............................................................................31

Call Log Submenu ......................................................................................31

Choose a Call Log Record ....................................................................32

Dial a Call Log Record ..........................................................................33

Save a Call Log Record ........................................................................33

Delete a Single Call Log Record............................................................33

Date/Time information of a Call Log Record..........................................33

Delete All Records in Any Call Log Group ............................................34

Phone Book Submenu................................................................................34

Searching Telephone Records ..............................................................35

Name Search ....................................................................................35

Quick Search ....................................................................................36

Telephone Configuration ............................................................................41

Call Duration ..........................................................................................42

Local Date/Time ....................................................................................43

Ringer Tone ............................................................................................44

LCD Contrast ........................................................................................44

Function Key ..........................................................................................45

6

Network Configuration ................................................................................46

Enable/Disable DHCP............................................................................47

Terminal IP Address ..............................................................................48

Terminal Subnet Mask............................................................................49

Default Gateway IP Address ..................................................................50

Enable/Disable VLAN ............................................................................51

VLAN ID ................................................................................................52

Restore Factory Settings........................................................................53

View Info ................................................................................................53

Web-Based Setup and Configuration ........................................................54

User Configuration ................................................................................54

Phone Settings Configuration ................................................................56

Function Key Configuration....................................................................57

Phone Book............................................................................................58

Password Change ................................................................................59

Administrator Configuration....................................................................60

Network Configuration ......................................................................62

H.323 Configuration ..........................................................................63

SNTP Server ....................................................................................64

Codec Configuration ........................................................................65

Add/Del User and Password ............................................................66

Change Administrator’s Password ....................................................67

Update Firmware....................................................................................68

Update Configuration File ......................................................................70

Appendix

General Information ........................................................................................72

Factory Default Settings..................................................................................72

Setup Menu Tree ............................................................................................74

7

List of Figures

Figure 1-1 The UIP300G IP Phone................................................................8

Figure 2-1 Footstand Mounting....................................................................13

Figure 2-2 Plugging Handset Cord into Telephone......................................14

Figure 2-3 Connecting to LAN ....................................................................14

Figure 2-4 Web Login Screen......................................................................19

Figure 2-5 H.323 Configuration ..................................................................20

Figure 2-6 Codec Configuration ..................................................................21

Figure 4-1 Call Log Menu Structure ............................................................31

Figure 4-2 Actions Applicable to Phone Book Records ..............................34

Figure 4-3 Normal Phone Book Record Data Input Sequence ..................37

Figure 4-4 Phone Configuration Menu ........................................................41

Figure 4-5 Function Keys ............................................................................45

Figure 4-6 Web Login Screen......................................................................54

Figure 4-7 User Main Page..........................................................................55

Figure 4-8 Phone Settings ..........................................................................56

Figure 4-9 Function Key Configuration ........................................................57

Figure 4-10 Phone Book Configuration ........................................................58

Figure 4-11 Password Change ......................................................................59

Figure 4-12 Web Login Screen......................................................................60

Figure 4-13 Administrative Configuration Main Page ....................................61

Figure 4-14 Network Configuration................................................................62

Figure 4-15 H.323 Configuration ..................................................................63

Figure 4-16 SNTP Server Configuration........................................................64

Figure 4-17 Codec Configuration ..................................................................65

Figure 4-18 Add/Delete User ID and Password ............................................66

Figure 4-19 Administrator Password ............................................................67

Figure 4-20 Update Firmware........................................................................68

Figure 4-21 Update Configuration ................................................................70

8

Chapter 1 Product Description

General Information

The UIP300G is a business IP telephone in an enterprise LAN environment and
will be connected to a softswitch.

This chapter describes the features of the UIP300G IP Phone and protocols that
are used.

LCD

Message Waiting Indication

Menu

Cancel/Del

Select

Up/Down

Arrow Keys

Function
Keys (5)

Redial

Conference

Transfer

Hold

Line 1

Line 2

Mute

Volum e

Up/Down

Speakerp hone

and

Headset

Figure 1-1 The UIP300G IP Phone

9

Standard Features of the Telephone

The UIP300G comes equipped with the following standard features.

• 2-line, 24-character alphanumeric LCD display

• 10 LED indicators (Line 1, Line 2, Message Waiting Indication, Mute,

Speaker/Headset, and five Function keys)

• 12-key dial pad

• 20 specific keys (five Function keys, Menu, Select, Cancel/Del, Transfer, Mute,

Redial, Hold, Conference, Speaker, Line 1 and 2 keys, Volume Up/Down keys,
and Up/Down Arrow keys)

• Date and time configured locally or from SNTP Server

• Call duration display

• Volume control for speaker, handset, headset and ringer

• LCD contrast control

• Phone book and speed dial

• Call Logs (Incoming/Outgoing/Missed)

• Redial, Hold, Mute

• Call Waiting, Call Transfer, 3-way Conference and Do Not Disturb (DND)

• Display Caller ID (Name)

• On-hook dialing, Handsfree talking

• DTMF generation

• 8 ringer tones

VoIP Specific Features

The following features are specific to the VoIP function.

• H.323 standard compliant (H.323 (V.3))

• Voice Codec: G.711 (µ-Law and A-Law), G723.1A(6.3kbits/s), G729AB

• E.164 dialing

• Acoustic Echo Cancellation (AEC) (G.167)

• Rapid configuration with DHCP or statically configured IP address

• Voice Activity Detection (VAD)

• QoS (IEEE 802.1 p/q based and DiffServ)

• Jitter compensation

• 10/100 Base-T Ethernet Interface

General Features

The following general features include:

• Terminal and web-based configuration

• Firmware/configuration update via Web

• Password protection for configuration

10

Control and Functions of the Telephone

To make phone operations easier and to avoid user confusion, many required
functions are already programmed into the fixed function keys. There are 15
fixed function keys in the UIP300G.

• Speaker/Headset – Turn speakerphone or headset on/off

• Mute – Enable/disable the Mute function

• Hold – Hold the called party

• Transfer – Transfer one party to another

• Conference – Establish a 3-way conference conversation

• Redial – Redial last called number / Enter “,” , pause digit for Phone Book or

speed dial numbers

• Menu – Display the main Setup menu if in the Standby screen, or return to
Standby screen if in any menu or submenu screen

• Select – Confirm a particular choice inside any menu screen

• Cancel/Del

◊ Works as delete key when there is one or more character(s)
◊ Works as backspace key when there is one or more digit(s)
◊ Deletes whole character string or digit(s) if this key is pressed and held

for 2 seconds or longer

◊ Cancels the operation in the setup menu and returns to the previous menu.

• Navigation (up) and (down) Keys – Used mainly to navigate (up/down) the
Setup Menu

• Volume (up) and (down) Keys – Used for volume adjustment

• Telephone Line Keys – Used to select telephone line 1 or 2

Function Keys

There are five user programmable function keys in the UIP300G. Each can be
programmed to one of the three available functions – Speed Dial, Do Not Disturb
(DND), and Voice Mail.

LED Status

There are 10 LEDs in the UIP300G. Four LEDs are located adjacent to the four
fixed keys. Lines 1 and 2, Speaker/Headset and Mute show the status of the
function in each key. The Message Waiting Indication is dedicated to notify the
user of the arrival of an incoming call or a new voice mail. Table 1-1 “LED Status”
lists the LEDs and describes that states of the LED.

11

Table 1-1 LED Status

LED LED On LED Blinking LED Off

Speaker/Headset Turned on when the N/A When not used

SPK/HS is pressed

Mute

While microphone is muted

N/A While not muted

Message Waiting When there is 1 or Arrival of Incoming Call when no more new
Indication more new voice mail(s) when voice mail or no

It is a regular call incoming call
It is a call waiting call is waiting
(Fast blinking)

Line 1 When in use When Line 1 is on hold. When not in use

(Slow blinking)
When incoming call
comes thru Line 1
(Fast blinking)

Line 2 When in use When Line 2 is on hold. When not in use

(Slow blinking).
When incoming call
comes thru Line 2

(Fast blinking)
Function Keys
Speed Dial/ Turned on when the N/A Whenever any of the

Voice Mail key is pressed and it following occurs:

remain on for • 5 seconds after it is
5 seconds. turned on

• When it returns to
on hook

• A different speed
dial key is pressed

Do Not Disturb While DND is activated N/A While DND is off
(DND)

Specifications

The following specifications apply to the physical interface, power supply
and speaker.

Physical Interface

◆ 10/100 Base-T (RJ-45) x 1

◆ Handset (RJ-22) x 1

◆ Headset (phone jack - 2.5 mm) x 1

◆ DC Jack x 1

Power Supply

◆ DC 48V, 0.25A (AD300)

◆ Line Power (PowerDsine)

Speaker

◆ 8 Ω, 1 W

• The On and Off time for “Fast blinking” is 200 ms cycle and the time for “Slow
blinking” is 1 sec. cycle.

• Line LED’s will blink during hold, if the Hold key is configured to perform
local hold.

11

12

Optional & Replacement Equipment

The following equipment is available for use with your UIP300G IP Phone.
The table below provides a description and Part Number.

Table 1-2 Optional & Replacement Equipment

Description Part Number Equipment Diagram

AC Adapter

1

AD300

Cord UIPA3035

Handset UIPA3030

Headset EXP9530

EXP9730

5 Port 10/100 PCS500
Ethernet Switch

1. This product is intended to be supplied by a listed direct plug-in power unit marked “Class 2” or

“LPS” and rated 48VDC with minimum 0.25A output.

13

Chapter 2 Installation and Basic Setup Instructions

General Information

This chapter provides instructions for installing the foot stand on the UIP300G,
connecting the UIP300G to the LAN and sample setup instructions for setting up
the telephone.

Attaching the Footstand to the Telephone

The footstand is included with the UIP300G. The footstand can be attached to
the bottom of the UIP300G, allowing the user to tilt the telephone at either low or
high angle or to wall mount the telephone. The adjustments are clearly marked
on the footstand with arrows indicating the direction that the footstand should be
attached to the bottom of the telephone for the desired height or
wall mounting.

To attach the footstand to the telephone, determine the desired adjustment and
align the tabs on the footstand with the tab receptacles on the bottom of the
telephone by matching the arrows. Press firmly on the footstand to lock the tabs
in place.

Low Desktop High Desktop Wall Mount

Figure 2-1 Footstand Mounting

14

Connecting the Telephone

Before using the UIP300G, it is necessary to connect the handset to the
telephone and to connect the telephone to the LAN network.

1. Connect the handset to the handset port located on the left side of
the telephone.

Handset Port

2. Connect the Ethernet cable from the LAN to the network port on the UIP300G.
The network port is located on the back side of the telephone.

Do not connect the UIP300G to a standard telephone line.

Connecti on to LAN

(Straight Connection)

AC Adapter
Connecti on

Figure 2-3 Connecting to LAN

Figure 2-2 Plugging Handset Cord into Telephone

3. If a powered hub is not being used, connect the AC adapter to the power
jack and then connect the adapter to a suitable power outlet.

15

Quick Setup Procedure

This example provides steps for configuring an IP telephone via terminal based
configuration (User interface) and the web browser based configuration. Both the
UIP300G terminal interface and the web browser can be used to modify the
information for the operation of the UIP300G.

The IP terminal network settings must be configured before the web browser
is configured.

Terminal Configuration using the UIP300G

To access the Phone Configuration Menu and set up a telephone configuration:

1. Press MENU key.

2. Use the or keys to access the Configuration menu,

then press SELECT key.

3. Use the or keys to access the Network Configuration menu,

then press SELECT key.

4. When prompted to enter “Password” enter the password,

then press SELECT key.

Setup Menu:

Configuration

3/4

Configuration Menu:

Network Configuration

2/3

Enter Password

******

16

5. Once the correct password is entered, the DHCP option is displayed (default
is Disabled). Press SELECT key to access the Disabled screen.

The default password is 654321. If an incorrect password is entered, the
message “Incorrect Password” is displayed for one second. The Password
screen is returned and the password can be entered again.

If using a static IP address, DHCP must be set to Disabled.

If enabled is selected, the IP address, Subnet Mask address and Default
Gateway address cannot be entered.

This selection is not recognized until the telephone has been reinitialized. When
the telephone has been restarted, the LCD shows “Initializing...\” and then
“Searching DHCP Server...”. After initialization is complete, the telephone returns
to the time and date display.

6. Press SELECT key to accept the Disabled option or press to access the
Enable option.

If Disabled is the desired option, press SELECT key. When the “Press
SELECT to Restart” message is displayed, press CANCEL/DEL key to return
to the Network Config menu and configure other network parameters.

If Enabled is the desired option, press SELECT key to accept the option.
When the “Press SELECT to Restart” message is displayed, press
CANCEL/DEL key to return to the Network Config menu , or press SELECT
key to restart the telephone.

Incorrect Password

Network Config:

DHCP Disabled

1/6

DHCP

Disable

1/2

DHCP

Enable

2/2

17

7. Use to access the IP Address screen on the Network Config menu.

8. Press SELECT key to display the current IP address.

9. Press SELECT key again and enter the new IP address. The format of the IP

address is: XXX.XXX.XXX.XXX

Numbers 0~255 are valid entries for the IP address.

The new IP address is not recognized until the telephone has been restarted.
When the telephone has been restarted, the LCD shows “Initializing...\”. After
initialization is complete, the telephone returns to the time and date display.

The following IP addresses, 0.0.0.0 and 255.255.255.255, are not valid.

10. After the correct IP address is entered, press SELECT key.

11. When the “Press SELECT to Restart” message is displayed, press

CANCEL/DEL key to return to the Network Config menu.

12. Use the to access the Subnet Mask screen on the Network Config Menu.

13. Press SELECT key to display the current Subnet Mask address.

14. Press SELECT key again and enter the new Subnet Mask. The format of the

Subnet Mask is:
XXX.XXX.XXX.XXX

Numbers 0~255 are valid entries for the Subnet Mask.

15. After the correct Subnet Mask is entered, press SELECT key.

Network Config:

IP Address

2/6

Network Config:

Subnet Mask

3/6

18

16. When the “Press SELECT to Restart” message is displayed, press
CANCEL/DEL key to return to the Network Config menu.

The new Subnet Mask address is not recognized until the telephone has been
restarted. When the telephone has been restarted, the LCD shows “Initializing...\”.
After initialization is complete, the telephone returns to the time and date display.

When the telephone has been restarted, the LCD shows “Initializing...\”. After
initialization is complete, the telephone returns to the time and date display.
Once reinitialization has been completed, the changes that were made are now
in affect.

17. Press to access the Default Gateway screen.

18. Press SELECT key to display the current default Gateway IP address.

19. Press SELECT key again and enter the default Gateway IP address.
The format of the default Gateway IP address is:
XXX.XXX.XXX.XXX

Numbers 0~255 are valid entries for the default Gateway IP Address.

20. After the correct default Gateway IP address is entered, press SELECT key
to restart.

Network Config:

Default Gateway

4/6

19

Web Browser Configuration

To access the web-based setup and configuration program:

1. Start the web browser from a PC that is connected to the same IP network
as the UIP300G.

2. Check the IP address on the telephone and enter that IP address in the web
browser eg., http://169.254.1.10. (Refer to the “View Info” section on page 53
to obtain the IP address of UIP300G.) When the Enter Network Password
screen appears, enter the User Name and Password. Click OK.

• At default the User Name is admin.

• The password is 6~10 digits. At default the Password is 654321.

Figure 2-4 Web Login Screen

20

3. Access the H.323 Configuration screen and enter:

• GK/GW Mode: GW_MODE/GK_MODE_MAN/GK_MODE_
AUTO/IP_MODE

• GK/GW IP Address: XXX.XXX.XXX.XXX

• GK/GW Port#: XXXXX

• E.164 Alias (Phone #): XXXXXXXXXXXXXX

• H323_ID Alias: XXXXXXXXXXXXXXXXXXXX

Figure 2-5 H.323 Configuration

4. Click Submit.

The phone will restart after clicking on Submit and the new settings are stored.

For “GK/GW Port #” the port number is usually 1719 for GK modes and 1720 for
GW mode.

21

5. Access the Codec Configuration screen and change Preferred Codec

(The default preferred code is G.711_Mu).

6. Click Submit. The UIP300G is now ready for operation.

Figure 2-6 Codec Configuration

The phone will restart after clicking on Submit and the new settings are stored.

22

Chapter 3 Basic Operations

General Information

There are several basic operations that the UIP300G performs. Some of the
basic operations include:

• Standby

• Originating a Call

• Receiving a Call

• 2-line Operation

• Setting the Volume

Telephone Operations

Standby

When the telephone is powered on, “Initializing...\” is shown while the
telephone is starting up. The last character on the LCD rotates, indicating that
the software is still running.

Before the telephone switches to standby mode, the firmware version is shown
on the LCD for five seconds (below is an example for the firmware version 1.00).

Initializing...\

Firmware Version: gel.00

23

While the phone is on-hook standby mode, the current date and time is shown
on the LCD.

The telephone extension (E.164) number or H323 ID or display name is also
displayed on the LCD (if available) while the telephone is on-hook and in
standby mode.

Originating (Outgoing) Calls

Users can make calls using a handset or the handsfree feature. (Refer to
“Handsfree” on page 27 for a detailed discussion of handsfree operation.)

Using the Handset

To originate a call using the handset:

1. Pick up the handset (the telephone is off-hook).

2. Dial the telephone number (or extension number), or the IP address of the
called party.

3 Press SELECT key to initiate dialing or wait four seconds after the last

digit entered.

To cancel out of the phone book, press CANCEL/DEL key.

07/02/02 4:30PM

07/02/02

3000

4:30PM

Using the Phone Book

To originate a call using the phone book:

1. Press to access the phone book. (Refer to “Phone Book” on page 27
for instructions for adding, editing, or deleting Phone Book entries.)

2. Once the phone book is displayed, use either the or to navigate
through the entries.

3. Once the desired entry is displayed in the LCD, press SELECT key to
initiate the call.

24

Using On-Hook Dialing

Users can enter telephone numbers before going off-hook (while the
telephone is in standby mode).
To dial the number:

1. Enter the destination number.

2. Go off-hook with the handset or speakerphone.

3. The outgoing call is initiated.

Receiving Calls

When there is an incoming call, the Message Waiting Indication LED and the
line LED flash. Users can answer the call using the handset or handsfree
(using the speakerphone or headset).

Answering Calls Using the Handset

To answer an incoming call:

1. Pick up the handset.

2. Begin the conversation.

Answering Calls Handsfree

To answer an incoming call:

1. Press the SPEAKER/HEADSET key or press the line key (the handset

remains in the cradle).

2. Begin the conversation.

If the headset is plugged in, conversation will be done through the headset
instead of speakerphone.

2-Line Operation

The UIP300G supports 2-line operations.

Accessing Line 1

The UIP300G uses Line 1 if the user picks up the handset or presses the
SPEAKER/HEADSET key.

25

Accessing a Line Using the Line Key

Press Line 1 or Line 2 to access the appropriate line. When the line key is
pressed, the LED on the line key turns on indicating the selected line is in
use. If the handset is used, the user hears a dial tone through the handset.
If the handset is in the cradle and the telephone was originally on-hook,
pressing the line key causes the telephone to go off-hook and turns on the
handsfree feature. The user hears dial tone through the telephone speaker.

Volume Control

There are four volume settings:

◆ Handset

◆ Headset

◆ Speakerphone

◆ Ringer Volume

Handset Volume Control

To change the volume on the handset:

With the handset off-hook, press (increase) or (decrease) to adjust the
volume. The volume of the handset changes as the keys are pressed.

If no activity is detected for 2.5 seconds, the volume setting screen
disappears and returns the LCD to the original display and the volume setting
is saved.

There are five volume levels for each volume setting.

Handset Volume

26

Headset Volume Control

The headset volume is adjusted in the same way that the speakerphone
volume is adjusted. Refer to “Speakerphone Volume Control” on this page.

Headset Volume

Ringer Volume

Speakerphone Volume Control

The speakerphone volume is adjusted in the same way that the handset
volume is adjusted when the speakerphone is in use. Refer to “Handset
Volume Control” on page 25.

Speaker Volume

The speakerphone can only be adjusted if the headset is not plugged in.

The headset volume can only be adjusted if the headset is plugged in.

Ringer Volume Control

To change the ringer volume:

With the telephone on-hook, press (increase) or (decrease) to adjust
the volume. The volume of the ringer changes as the keys are pressed.

If no activity is detected for 2.5 seconds, the volume setting screen
disappears and returns the LCD to the original display and the volume setting
is saved.

27

Feature Operations

The operation for the basic features of the UIP300G are described in
this section.

Handsfree

This feature allows the user to make a call or receive a call without using the
handset. This feature is provided when using the speakerphone or the headset.

Speakerphone

When the SPEAKER/HEADSET key or one of the line keys is pressed (and
the headset is not plugged in), the user can listen from the built-in speaker
and can speak through the built-in microphone. If the handset goes off-hook
while the speakerphone is in use, the speakerphone is turned off and the
handset becomes active. If the handset is active and the speakerphone goes
off-hook (by pressing the SPEAKER/HEADSET key), the handset becomes
idle and the speakerphone becomes active.

Headset

When the SPEAKER/HEADSET key is pressed and the telephone detects
that the headset is plugged in, the voice path of the speakerphone and the
microphone (used by the speakerphone) is disabled and the speaker and
microphone inside the headset is activated.

Receiving a Call Using Handsfree

When the telephone rings, the user can press the SPEAKER/HEADSET key
or the line key with the flashing LED without picking up the handset. The
SPEAKER/HEADSET LED goes on and the LCD screen is the same as if
the user answered the call using the handset.

To disconnect the call, press the SPEAKER/HEADSET key. Pressing the line
key does not disconnect the call.

If the handset is picked up, the Handsfree feature is disabled and the
telephone returns to normal operation allowing conversation through
the handset.

Phone Book

The Phone Book feature allows users to store up to 50 telephone records.
Each records contains the following data fields:

◆ Name – alphanumeric identification of a party (stored phone book entry)

◆ Number – telephone number or extension of the party (stored phone

book entry)

The Phone Book can be accessed in two ways:

◆ Press the navigation key to access the quick Phone Book (dial only).

◆ Press the MENU key to go to the Setup Main menu. Select the “Phone

Book” entry option that appears as the second item inside the menu.
Records inside the phone book can be searched (by name), dialed, edited or
deleted. Refer to “Phone Book Submenu” on page 34.

28

Programmable and Fixed Function Keys

There are five programmable keys and five fixed functions keys in the
UIP300G. Programmable function keys can be assigned to one of the three
available functions: Speed Dial, Do Not Disturb (DND), or Voice Mail.

Speed Dial

Users can make calls by pressing a key that has been previously
programmed for speed dialing. Users can press a speed dial key after going
off-hook with the handset or with the speakerphone. If the user presses a
speed dial key while on-hook, the telephone immediately goes off-hook with
the speakerphone and starts dialing the number.

Do Not Disturb (DND)

Do Not Disturb allows users to ignore all incoming calls. The calling party
hears a busy tone or an announcement, or sees the “Connection Failed”
message displayed on the LCD when DND is activated.

To use DND, a function key must be assigned. Refer to “Function Key” on
page 45 for instructions for assigning DND to a function key.

To activate DND:

Press the FUNCTION key assigned for DND.
The DND key LED remains lit while the feature is activated.

To deactivate DND:

Press the FUNCTION key assigned for DND.
The DND key LED goes off.

The DND key can only be activated and de-activated while the phone is on-hook
and in the standby screen.

MWI is only available if it is supported by the phone system.

Voice Mail

The UIP300G supports voice mail service. In order to access this feature,
the user’s IP terminal must be connected to the existing voice mail system.
When a new message arrives, the Message Waiting Indication turns on to
notify the user that a new voice mail message is waiting.

To access voice mail:

Press the FUNCTION key assigned for voice mail or dial the voice mail
number manually. Refer to “Function Key” on page 45 for instructions for
assigning a function key to access voice mail.

The user is connected to the voice mail system and prompted by instructions
to access the their mailbox. The Message Waiting Indication remains lit
solid until the UIP300G receives “No Message” indication from the voice
mail system.

29

The redial via the call logs feature will not be available if the outgoing call logs
is empty.

Redial
Redial may be set to dial a set of DTMF digits to invoke a gateway/gatekeeper

redial, or may be set to provide quick access to the outgoing calls log.

Redial – Call Logs

The IP phone retains the last 30 outgoing calls (numbers if dialing manually or
names if dialing from phone book) user has dialed. User can press REDIAL
key to show the last outgoing call on the LCD. The redial key will be functional
when no digits have been entered in the standby mode or while hearing dial
tone during off hook. User can use the and keys, or REDIAL key (which
works as a key) to choose which entry to dial. Once the desired record is
displayed, user can make a call by pressing SELECT key. The phone will dial
through hands free automatically if it is not already off hook. If the user presses

CANCEL while a record is being display, Redial screen will exit.

Redial — DTMF String

The redial records are retained in the gateway/gatekeeper system and will
be invoked by sending a pre-assigned DTMF string to the system when the

REDIAL key is pressed.

Mute

Mute can be used during a conversation.
To activate mute:
Press the MUTE key.
The user’s voice is muted, however, the user can still hear the other parties
participating in the call. The Mute LED goes on to remind the user that their
voice is being muted.

To deactivate mute:
Press the MUTE key.

Mute is disabled, the Mute LED goes off and the user’s voice can now be heard
by other parties.

Hold

The phone can be configured to use local hold or send an assigned DTMF
string when the HOLD key is pressed.

Hold - Local

During a conversation, the user can put the other party on hold by pressing
the HOLD key. The LED of the line that is put on hold will blink continuously,
and the LCD will display hold indication in one of two situations.

· When one line is on hold and the second line is not used

· When both lines are on hold

To resume the call, press the line key for the party on hold. The Hold
indication message will disappear and the line LED will go from blinking to
solid on. The other party will be back to the conversation. The LCD will
resume to screen prior to pressing hold.

30

Transfer

The phone can be configured to send an assigned DTMF string when the
TRANSFER key is pressed.

1. User gets connected with one remote party.

2.

User presses TRANSFER key.

3. Follow the instructions specific to the gatekeeper/gateway system being
used to proceed with the call transfer operation.

Conference

The phone is capable of performing local 3-way conference mixing, or
transmitting an assigned DTMF string when the CONFERENCE key
is pressed.

3-Way Conference Call – Local Mixing

The phone is a capable of locally mixing a 3-way conference call.

1. User gets connected with one remote party

2. User presses CONFERENCE key. This puts remote party on Hold.

3. User enters dial digits to call a third party. If the user wants to use the
Phone Book, press key to open the Phone Book. Refer to “Phone Book
Submenu” on page 34 for the Phone Book Quick Search operation.

4. User presses SELECT key to initiate the second call.

5. Third party answers the call and user is in conversation with the third party.

6.

User presses CONFERENCE key again. Three parties will now participate in the
conference call.

7. Press CONFERENCE key to terminate the entire conference.

3-Way Conference Call – DTMF String

1. User gets connected with one remote party

2. User presses CONFERENCE key.

3. User must follow steps depending on the gateway/gatekeeper system
being used to complete the conference call.

Call Waiting

This feature allows a user to answer an incoming call while one of the two
lines is being used. When there is an incoming call and one of the two lines
is in use, the user hears a call waiting tone and the LED on the available line
blinks continuously. A call waiting tone and flashing LED continues until the
call is answered or the incoming call is terminated.

To answer the incoming call:

1. Press the HOLD key to put the current party on hold.

2. Press the line key where the new incoming call is ringing.

• If the user presses the line key without first putting the current party on hold,
the current call is automatically dropped.

• The instructions for answering a call waiting may not apply to your phone, if
you are not using the local hold setting.

The phone will provide music on hold, if using local hold.

Hold - DTMF String

User presses HOLD key. This puts the remote party on hold via the gateway/gatekeeper
system and there is no indication of this hold on the LCD. The steps for recovering from
DTMF String hold are gateway/gatekeeper system dependent.

31

Call Log Submenu

There are three types of call logs – Incoming, outgoing and Missed call logs –
inside the Call Log Menu. Besides the three types of call logs, the Call Log Menu
also includes the Delete Logs function as the fourth item. This function is used to
delete all call log records inside any chosen call log group. When a record is
chosen, user can apply one of the four functions– Dial, Save, Delete or
Date/Time – to the chosen record.

Call Logs

Incoming

Missed

Outgoing

Delete Logs...

Confirm Delete

Incoming Log

Missed Log

Outgoing Log

All Logs

Dial?

Delete?

Save?

Date/Time?

Single Call

Record

Figure 4-1 Call Log Menu Structure

When MENU key is first pressed, the Setup Menu and Call Logs submenu
are displayed.

Chapter 4 Setup Menu

General Information

This chapter describes how to setup and configure the UIP300G.
The main setup and configuration menu is the Setup Menu. This menu consists

of three submenus and displays information about the UIP300G:

• Call Log Menu – This submenu is used to set operations relating to incoming,
outgoing and missed call log information.

• Phone Book Menu – This submenu is used for setting up any operations
relating to phone book records.

• Configuration Menu – This submenu includes two types of configurations and
allows users to restore the factory default settings:

• Telephone Configuration

• Network Configuration

• Restore Factory Settings

• View Information – Displays the telephone IP address and firmware version.

Basic Setup Menu Options

This menu provides access to the three submenus: Call Log, Phone Book
and Configuration.

To access the Setup Menu:

1. Press MENU key.

2. To navigate the submenu options, press the and keys. When the

desired submenu option is accessed, press the SELECT key to display the
selected submenu.

Every call record in any call log group, contains 4 common data fields
regardless of its call log type:

1. Caller’s Name

2. Caller’s Phone Number

3. Call Date

4. Call Time
To access the Call Logs submenu, use the or arrows to choose Call Logs
from the Setup Menu.

32

Setup Menu:

Call Logs

1/4

Call Log:

Incoming

1/4

Call Log:

Missed

3/4

Press
twice

· No log will be kept for IP dialing.

· If the number of an incoming call log is “Number Unavailable”, there are only
two operations for this call log, “Delete” or “Date/Time.”

• Each call log record has a number shown at the top right corner to show the
receiving order. “1” is the latest record. The larger the number, the older the
record it is.

• When the latest record is being shown, a press of key will move to the last
call log record (oldest record)

Choose a Call Log Record

A call log record from any call log group can be chosen as follows:

1. Choose Call Log from the Setup Menu and press the SELECT key or go

to Step 2 directly by pressing from the standby mode or while hearing
dial tone during off hook. If user has already entered any character on
LCD, pressing or key will be ignored.

2 Choose one of the four items from the Call Log Menu. The first item of

the Call Logs menu (Incoming) is displayed. Use or to move to
different items under Call Log and choose a particular item by pressing
the SELECT key.

3. The first call log record from the chosen log group appears. User presses
or navigation keys to find the record of interest and presses the

SELECT key. On next screen, user can choose one of the four possible
actions – Dial, Save, Delete, and Date/Time.

33

Dial a Call Log Record

If user continues from the above section, press the SELECT key and user
will see the first available action– Dial. (User can press the and
navigation keys to change to other actions). To make a phone call using the
number inside the chosen call log record, choose Dial by pressing

SELECT key.
Save a Call Log Record

If user continues from the “Choose a Call Log Record” section, press the
SELECT key and user will see the first available action– Dial. (User can
press the and navigation keys to change to other actions).

1. Press the navigation key to move to the Save action.

2. Press the SELECT key and the record will be saved to the phone book.

Continue from step 2 of the “Add a Phone Book Record” section on page 36
to finish saving the call log record.

When the save action is performed successfully, the display will return to the
list of call log records and user can perform the actions explained in the “Edit
Phone Book Record” section step 3 on page 39 or returns to the Call Log
menu by pressing the CANCEL/DEL key.

Delete a Single Call Log Record

1. Press the navigation key to change the action to the Delete action.

2. Press the SELECT key. The delete confirmation message displayed on

the LCD screen. User can choose either to delete the current selected call
log record, or to cancel the delete action.

3a.If user presses the SELECT key, the phone will delete the chosen record.

Then, the delete successful message will be displayed for 1 second.
Following this operation, the LCD will display the next record on the log as
in Step 1 or the first record if the deleted record was the last one.

3b.If CANCEL/DEL key is pressed, the delete action will be cancelled, and

the display will return to Step 1.

Date/Time information of a Call Log Record

Date/Time is the last action inside the call log operation menu. This menu will
display the name (if available), date and time of the call of a call log record.

1. Press the navigation key to change the action to the Date/Time action.

2. Press the SELECT key. The following info will be displayed:

◆ 1st line: Name

◆ 2nd line: The date and time of the call log

The name in an outgoing call log will be available only for the calls made from
the Phone Book or the Call Log. “Name Unavailable” will be displayed for the
outgoing calls when the phone number is dialed using the keypad.

34

Incoming Log Deleted

Missed Log Deleted

All Logs Deleted

Outgoing Log Deleted

Phone Book Submenu

The “phone book” feature allows users to store up to 50 telephone records.
The Phone Book function appears as one of the submenus in the Setup Menu.
The Phone Book submenu provides four functions relating to the phone book
records. Refer to Figure 4-2 “Actions Applicable to Phone Book Records”.

Phone Book

Edit

Delete

Add

Dial

Figure 4-2 Actions Applicable to Phone Book Records

Delete All Records in Any Call Log Group

Besides three call log groups, the Call Log Menu also contains the Delete
Logs feature. It allows user to delete all records inside any particular (or all)
call log group(s).

1. From the Call Log Menu, choose Delete Logs items and press

SELECT key.

2. Choose any group of call logs and press the SELECT key.

3. After pressing the SELECT key from Step 2, the log delete confirmation

screen will prompt. At this moment, if SELECT key is pressed, go to Step

4. If CANCEL/DEL key is pressed, the display will return to the previous
menu with the same log type in Step 2.

4. The phone will delete all records inside the chosen call log group. One of

the log delete successful messages below depending on the log type will
be displayed for 1 second.

35

Name Search

This search is typically used when the Dial or Edit features are chosen
from the Phone Book menu. Edit and dial features are chosen by pressing
the SELECT key on the Phone Book menu.

To perform a name search:

1. Choose Dial or Edit from the Phone Book Menu by pressing the

SELECT key. It will go to the name search screen.

Searching Telephone Records

The “phone book” can hold up to 50 records. As a result, navigating through
the telephone records can become time consuming. To avoid lengthy
searches, the UIP300G allows users to search the telephone records by
entering a name or the first letter of a name. There are two types of
searches: name search and quick search.

This quick access operation applies to dialing only. If the user has already
entered a character on the LCD, pressing the has no affect.

Enter Name: (UPPER)

If the phone book is empty, user will see the message, “Phone Book is Empty”,
for one second.

To access the Phone Book menu, use the or arrows to choose Phone
Book from the Setup Menu.

If the is pressed while the telephone is in standby mode and the date and
number are displayed in the LCD, the first Phone Book entry is shown.

Setup Menu:

Phone Book

2/4

Anderson. Peter

98173334444

2. Enter a name using the numeric keys on the keypad.

3. When finished entering the name or character(s), press the

SELECT key.

36

• During the name input, user can move the cursor by using and keys.

• When there are user input characters and the cursor is moved over a particular
character, a press of CANCEL/DEL key will delete the character that the
cursor is highlighting. All remaining character(s), if there is/are any, on the right
of the deleted character will move one space to the left.

• The search mechanism is not case-sensitive.

• If nothing is entered and the SELECT key is pressed, the first phone book
record will show up. Press or key to navigate to the record of interest.

• If there is no match, the first record exceeding the searching input criteria will
appear on the first line of the LCD display. For example, assume a search
string of “Pete J” is entered. If inside the phone book record list, there is a
name Pete K, which is stored right after another record with name Pete C. In
this case, the record Pete K will be displayed since it is the first record that
exceeds the searching criteria – Pete J. From the resulted record, user can
navigate to different records using and keys.

Peterson, John

98173334444

After the actual search is performed, the first record that matches the input
string appears on the first line of the LCD display.

Quick Search

This search is used to quickly navigate the “phone book” by pressing a digit
key. This is another way to quickly perform a name search.

To perform a quick search:

1. From the on hook standby screen or from off hook screen prior to
dialing digits, Press the key.

2. Press the dial digits on the keypad to retrieve the first phone book entry
name with the corresponding letter. For example, user would hit the “6”
key once to get the first entry beginning with the letter “M”. User would
hit the “6” key a second time to get the first entry beginning with the
letter “N”, and so forth.

• Press or key to navigate to the record of interest.

• The search mechanism is not case-sensitive.

Add a Phone Book Record

The phone book feature allows user to store up to 50 phone book records.
Each phone book record contains 2 data fields – Name and Number.

1. From the Phone Book Menu, choose the Add item using the and

navigation keys and press the SELECT key.

Phone Book Menu:

Add

2/4

37

• A name can be 24 alphanumeric characters.

• To switch from upper and lower case, press the # key.

• Press the corresponding number on the dial pad to enter the letters. For
example, number 2 on the dial pad is used to enter A, B and C. Press the 2
key once for the letter A, twice for B and three times for C. Use the other keys
on the dial pad the same way.

• To enter a space, press 0.

• The asterisk key can be pressed eight times to enter one of the following
characters:
1 time = .
2 times = @
3 times = *
4 times = #
5 times = –
6 times = &
7 times = (
8 times = )

1 sec.

Select

Select

Enter Name

Back to
Phone Book Submenu

Record Saved

Enter Phone Number

Enter Name:

Barbara Anderson

(lower)

2. After user chooses Add from the Phone Book Menu, the name input
screen is displayed. User can enter a name for the record. Press the
SELECT key when input is done.

If the Phone Book is full when user tries to add a new record, “Phone
Book is Full” message will be displayed on the screen. Then, it will return
to the Phone Book Menu with the Dial item on the display.

Otherwise the normal record adding procedure should be shown as follows.

Phone Book is Full

Figure 4-3 Normal Phone Book Record Data Input Sequence

38

• Whenever the CANCEL/DEL key is pressed, the last digit will be deleted.

• Whenever the REDIAL key is pressed, the character “,” will be inserted.

The “,” character represents a 2 second pause is to be performed between the
previous digit and the next digit, when the entry is dialed.

• The phone number field contains a phone number (or an extension) up to

24 digits.

Enter Phone Number:

98171234567

3. Enter the phone number.

4. After the phone number is entered, press the SELECT key.

The save confirmation screen will be displayed for 1 second. Then, it will
return to the Phone Book Menu with the Add item menu.

If the name of the entry already exists in the Phone Book, the following
message will be shown and ask user to replace the existing entry. If user
selects “Yes ”, the old entry will be deleted and the new entry will be
saved. If user selects “No”, it will return to the Step 2 to allow user to
change the name.

Name Exists Replace?

No: Cancel Yes: Select

Could not save

If the item could not be saved, the following message will be shown on the LCD
for 1 second and then return to the Phone Book Menu with the Add item. If name
or number or both is not entered, this message will also appear.

39

Delete One by One

Delete All

Phone Book Menu:

Edit

3/4

Edit a Phone Book Record

1. From the Phone Book Menu, choose the Edit item using the and
navigation keys and press the SELECT key.

2. User will enter the Name Search mode, search for the phone book
entry user wishes to edit and press the SELECT key. (Refer to the
“Name Search” section for directions on using Name Search mode.)

3. This brings user to the name editing field. At this point, user can follow
steps 2 through 4 of adding a new phone book record to complete
your task. The original data being edited will not be saved.

Delete Phone Book Records

1. From the Phone Book Menu, choose the Delete item using the and

navigation keys and press the SELECT key.

After choosing Delete from the Phone Book Menu by pressing the
SELECT key, user is given two choices to delete – Delete One by One,
and Delete All.

2. Use and navigation keys to select between erasing a single
record or all records. The currently selected choice, either “Delete One
by One” or “Delete All” will blink continuously. Press the SELECT key.

If the phone book is empty, you will see the message, “Phone Book is Empty”,
for one second.

If the phone book is empty, user will see the message, “Phone Book is Empty”,
for one second.

Phone Book Menu:

Delete

4/4

40

If the SELECT key is pressed the display will be shown for 1 second.
Then, the display will return to the next record on the list. If
CANCEL/DEL key is pressed, the delete will be aborted, and the display
will return to the phone book record list.

Delete All Records

3b.If Delete All Records is chosen from the menu, the Delete All

confirmation message will be displayed.

4b.If user presses the SELECT key, all phone book records will be

deleted. “All Records Deleted” will be shown on the LCD as below for
1 second then followed by “Phone Book is Empty” for another second.
Finally, the display will return to the Phone Book Menu.
If CANCEL/DEL key is pressed, the delete will be aborted, and the
display will return to the two delete choices – Delete One by One, and
Delete All.

Confirm Delete All

No: Cancel Yes: Select

All Records Deleted

Delete a Single Record

3a.If Delete One by One is chosen, it will bring the user to the first record

in the phone book. User may get to a desired record quickly by
performing a Quick Search and/or using the and keys to navigate
to the desired record. (Refer to the Quick Search section to learn
more about using the Quick Search feature.)

4a.After the desired record is located, press the SELECT key and it

brings user to the delete confirmation screen.

5a.Press the SELECT key to proceed or CANCEL/DEL key to return to

the phone record list.

Confirm Delete

No: Cancel Yes: Select

Record Deleted

41

Telephone Configuration

Telephone configuration includes configurations related to the characteristics of
features of a normal telephone call. These characteristics and features include:

◆ Call Duration

◆ Local Date/Time

◆ Ringer Tone

◆ LCD Contrast

◆ Function Key

When making entries in this menu, the CANCEL/DEL key operates in the
following manner:

- When there is/are one or more character(s), the CANCEL/DEL key operates
as a delete key.

- When there are no characters, the CANCEL/DEL key operates as a back key.
It takes you one level back to the previous screen.

Phone

Configuration

Ringer Tone

LCD Contrast

Function Key

Local Date/Time

Call Duration

Figure 4-4 Phone Configuration Menu

42

To access the Phone Configuration Menu and set up a telephone configuration:

1. Press MENU key.

2. When the Setup Menu screen is displayed, the Call Logs submenu is the
first selection that is displayed. Use the key to highlight the
Configuration submenu.

3. Press SELECT key. The Configuration Menu is displayed, showing the first
entry of the Configuration Menu, which is Phone Configuration.

4. Press the SELECT key to enter the Phone Configuration menu. This allows
access to the Phone Configuration functions.

Call Duration

1. Call Duration is the first option of the Phone Configuration menu, press

SELECT key to proceed to modifying it. Call Duration is displayed on the
LCD with the current setting. To change the setting, use the or keys,
then press SELECT key.

Configuration Menu:

Phone Configuration

1/3

Setup Menu:

Call Logs

1/4

Setup Menu:

Configuration

3/4

Phone Configuration:

Call Duration

1/5

Call Duration:

On

1/2

Call Duration:

Off

2/2

43

Local Date/Time

This selection allows the user to set the local date and time.

To access the Local Date/Time option and set date and time:

1. From the Phone Configuration menu use the or keys to access the

Local Date / Time option, then press SELECT key.

2. When “Enter Year” is displayed, enter the year (YYYY format), eg., 2003,

then press SELECT key.

3. When “Enter Month” is displayed, enter the month (1~12),

then press SELECT key.

4. When “Enter Day” is displayed, enter the day (1~valid max), then press

SELECT key.

5. When “Enter Hour” is displayed, enter the hour (0~23),

then press SELECT key.

6. When “Enter Minute” is displayed, enter the minutes (0~59), then press

SELECT key. The display returns to the Local Date/Time option.

• A data validation check is performed for each data field. If the date is not valid,
a warning message is displayed for one second.

• If SNTP server is enabled, date and time information is obtained from SNTP
server address configured by administrative user.

• When time is maintained locally, the telephone checks every 10 minutes for the
activation of an SNTP server and updates the local time if it is available.

• When the SNTP server request is successful, it automatically overwrites all
previous manual local date and time settings and updates the information from
the SNTP server.

• If an SNTP server is not available or it is disabled, the local time starts from
01/01/02 when the system is powered on.

Phone Configuration:

Local Date / Time

2/5

44

Ringer Tone

There are eight types of ringer tones available.

To access the Ringer Tone option and set the desired tone:

1. From the Phone Configuration menu use the or keys to access the

Ringer Tone option, then press SELECT key.

2. The current ring tone is displayed. Use the and keys to access the
desired ring tone. As you scroll through the selections, the ring tone can
be heard for three seconds. When the desired ring tone is displayed,
press SELECT key.

LCD Contrast

There are 10 levels of adjustment for the display contrast.

To access the LCD Contrast option and set the desired contrast level:

1. From the Phone Configuration menu use the or keys to access the
LCD Contrast option, then press SELECT key.

2. Adjust the contrast level by pressing the or keys. As the keys are
pressed, the contrast level changes. When the desired level is displayed,
press SELECT key.

Phone Configuration:

Ringer Tone

3/5

Phone Configuration:

LCD Contrast

4/5

45

3. Use the or keys to scroll the different features. When the desired

features is displayed, press SELECT key to assign the feature to the
Function Key.

Voice Mail, DND can only be assigned to one Function Key. If the user attempts
to assign these features to more than one Function Key, the message “Function
Already Assigned to Another Key” is displayed.

Function Key

Five function keys are available. Each of these keys can be assigned to one
of three possible features: Do Not Disturb (DND), Speed Dial and Voice Mail.
To access and program a function key:

1. From the Phone Configuration menu use the or keys to access the

Function Key option, then press SELECT key.

2. The telephone prompts the user to press the desired Function Key. When
the Function Key is pressed, the current assignment for the key is
displayed in the LCD.

Figure 4-5 Function Keys

Phone Configuration:

Function Key

5/5

46

Network Configuration

Network Configuration is used to assign administrative settings. All of these
settings are also available from the web-based administration and configuration.

Assignments in this menu are used to manage the network settings for the
UIP300G. Users can enter the Network Configuration menu from the
Configuration Menu. There are six network configurations that can be retrieved
or modified.

◆ Enable/Disable Dynamic Host Configuration Protocol
(DHCP IP Assignment for the Terminals)

◆ Terminal IP Address

◆ Terminal Subnet Mask

◆ Default Gateway IP Address

◆ Enable/Disable VLAN

◆ VLAN ID

To access the Network Configuration menu and assign administrative settings:

1. Press MENU key.

2. Use the or keys to access the Configuration menu,
then press SELECT key.

3. Use the or keys to access the Network Configuration menu,
then press SELECT key.

Setup Menu:

Configuration

3/4

Configuration Menu:

Network Configuration

2/3

47

The default password is 654321. If an incorrect password is entered, the
message “Incorrect Password” is displayed for one second.

5. Once the correct password is entered, the DHCP option is displayed with
the current setting.

Enable/Disable DHCP

The first option available in the Network Configuration menu is the DHCP
setting. This setting specifies whether the terminal IP address is assigned
dynamically via a DHCP server or statically assigned by the
administrator/user. If the DHCP IP option is enabled (turned on), the DHCP
server assigns the terminal IP address, terminal net mask and default
gateway address after the telephone is restarted. If this option is disabled,
the terminal IP address, terminal net mask and default gateway address are
manually assigned by the administrator/user.

4. When prompted to enter “Password” enter the password,
then press SELECT key.

Enter Password

******

Incorrect Password

Network Config:

DHCP Enabled

1/6

48

To access this option and to enable/disable DHCP:

1. If already in Network Configuration menu, use the or keys to
access DHCP option.

2. Press SELECT key.

3. Use the or keys to select enable/disable, and then press
SELECT key.

• If “Enable” is selected, the message “Press SELECT to Restart” is displayed.
Press SELECT key, to restart the telephone. The LCD shows “Initializing...\”
and then “Searching DHCP Server...”.

• If “Disable” is selected, the message “Press SELECT to Restart” is displayed.
Press SELECT key to restart the telephone. The LCD shows “Initializing...\” is
displayed. The display returns to the date and time.

• If “Disable” is selected, user must make sure that the terminal IP address,
terminal net mask and default gateway address are manually configured with
correct values.

• If you do not want to restart the telephone, press CANCEL/DEL key (to return
to the previous menu) or MENU key to exit programming and return the
telephone to standby mode. If LINE 1, LINE 2, SPEAKER/HEADSET, or if the
handset is picked up, the telephone goes off-hook and the restart is cancelled.

• When telephone restart is cancelled, the new network settings are not
accepted until the telephone is restarted.

Terminal IP Address

This option is used to read or change the current terminal IP address value,
if the DHCP assignment has been disabled. If DHCP is enabled, an IP
address is assigned by the DHCP server when the telephone reinitializes.

Press Select to Restart

Network Config:

IP Address

2/6

DHCP

Disable

1/2

DHCP

Enable

2/2

49

User will not be allowed to change value if DHCP is set to “enabled”.

To change the IP address:

1. If already in the Network Configuration menu, use the or keys to
access the IP address option.

2. Press SELECT key to display the current IP address.

3. Press SELECT key again and enter the new IP address.
The format of the IP address is:
XXX.XXX.XXX.XXX

Numbers 0~255 are valid entries for the IP address.

4. After the correct IP address is entered, press SELECT key and restart the
telephone, or press CANCEL/DEL key to cancel restart the phone and
continue setting up the telephone.

• Pressing CANCEL/DEL key returns to the previous menu. To exit programming
and return the telephone to standby mode, press MENU key.

• The new IP address is not recognized until the telephone has been reinitialized.
Once the telephone restarts, a restart confirmation message is displayed on
the LCD. “Initializing...\” is displayed in the LCD while the telephone resets. If
an error occurs during the initialization process, the message “Cannot Save” is
displayed in the LCD for one second before returning the IP address menu.

Terminal Subnet Mask

This option is used to set/retrieve the terminal network mask. If the DHCP is
enabled (turned on), the terminal mask is obtained from the DHCP server
when the telephone initializes. If the user sets the network mask, it is
overwritten by the value obtained from the DHCP server when the telephone
is reinitialized.

To set/retrieve the subnet mask:

1. If already in the Network Configuration menu, use the or keys to
access the Subnet Mask option.

2. Press SELECT key to display the current Subnet address.

Network Config:

Subnet Mask

3/6

50

Pressing CANCEL/DEL key returns to the previous menu. To exit programming
and return the telephone to standby mode, press MENU key.

3. Press SELECT key again and enter the Subnet Mask.

The format of the Subnet Mask is:
XXX.XXX.XXX.XXX

\

Numbers 0~255 are valid entries for the Subnet Mask.

4. After the correct Subnet Mask is entered, press SELECT key and restart
the telephone, or press CANCEL/DEL key to cancel restart the phone
and continue setting up the telephone.

• Pressing CANCEL/DEL key returns to the previous menu. To exit programming
and return the telephone to standby mode, press MENU key. If LINE1, LINE2,
SPEAKER/HEADSET are pressed or if the handset is picked up, the telephone
goes off-hook and restart is cancelled. When the telephone restarts, the
network settings are not used until after the telephone has been initialized.

• If the Subnet Mask is not valid, “Invalid Input” is displayed for one second
before returning the display to the Subnet Mask.

• The new Subnet Mask address is not recognized until the telephone has been
reinitialized. Once the telephone restarts, a restart confirmation message is
displayed on the LCD. “Initializing...\” is displayed in the LCD while the
telephone resets.

Default Gateway IP Address

This option is used to read/write the default Gateway IP address.

To read/write the default Gateway IP address:

1. If already in the Network Configuration menu, use the or keys to
access the Default Gateway option.

2. Press SELECT key to display the current Default Gateway.

3. Press SELECT key again and enter the default Gateway IP address.
The format of the default Gateway IP address is:
XXX.XXX.XXX.XXX

Numbers 0~255 are valid entries for the default Gateway IP Address.

4. After the correct Default Gateway IP address is entered, press SELECT
key and restart the telephone, or press CANCEL/DEL key to cancel
restart the phone and continue setting up the telephone.

Network Config:

Default Gateway

4/6

51

• The setting that is displayed, is the current assigned setting.

• “Press SELECT to Restart” is displayed. Press SELECT key, to restart the
telephone. The LCD shows “Initializing...\” is displayed. The display returns to
the date and time.

Enable/Disable VLAN

This option is used to enable or disable the VLAN.

To enable/disable VLAN:

1. If already in the Network Configuration menu, use the or keys to

access the VLAN option, and press SELECT key.

2. Use the or to change to the desired selection and press

SELECT key. The telephone display shows the selected VLAN setting.

Network Config:

VLAN Disabled

5/6

52

VLAN ID

This option is used to read/write the VLAN ID.

To read/write the VLAN ID:

1. If already in the Network Configuration menu, use the or keys to
access the VLAN ID option.

2. To read the VLAN ID, press SELECT key. To return to the previous
screen without changing the ID press CANCEL/DEL key. The screen is
returned to the VLAN ID screen.

3. To change the ID, press SELECT key. The change screen is displayed.

4. Press CANCEL/DEL key to erase the current ID number and use the dial
pad to enter the new number.
Valid VLAN ID numbers are 0~4095.

5. Press SELECT key. The telephone displays the message, “Press Select
to Restart”.

6. Press SELECT key to restart the telephone and save the new ID. The
LCD shows “Initializing...\”. The display returns to the date and time.

Network Config:

VLAN ID

6/6

VLAN ID:4095

Press Select to Change

VLAN ID

4095

53

To cancel the restoration process, press CANCEL/DEL key. To restore the factory
settings, press SELECT key. If SELECT key is pressed, “Restoring...” followed by
“Initializing...\” is displayed in the LCD. When the local date and time are
displayed on the LCD, the factory default settings have been restored.

Restore Factory Settings

This option restores the default settings and configurations that were set at
the factory.

To restore the factory settings:

1. From the standby mode screen, press the MENU key.

The Setup Menu is displayed.

2. Use the or keys to access the Configuration submenu.

3. Press SELECT key.

4. Use the or keys to access the Restore Factory Setting option.

5. Press SELECT key.

6. When prompted, enter the password (default: 654321) and press

SELECT key. The Restore Confirmation screen is displayed.

View Info

This option allows users to view the current IP address and firmware version.

To view the information:

1. Press MENU key.

2. Use the or keys to access the View Info submenu.

3. Press SELECT key. The IP address and firmware version are displayed in

the telephone LCD.

Configuration Menu:

Restore Factory Setting

3/3

Confirm Restore

No: Cancel Yes: Select

Setup Menu:

View Info

4/4

54

• At default the User Name is user.

• The password is 6 ~ 10 digits. At default the Password is 123456.

Web-Based Setup and Configuration

The web-based configuration enables a user to setup and configure the
UIP300G using a web browser on their PC. The web-based configuration
provides additional settings not available using the telephone.

Microsoft Internet Explorer v.4.0 or higher must be used.

User Configuration

To access the web-based setup and configuration program:

1. Start the web browser.

2. Check the IP address on the telephone and enter that IP address in the
web browser eg., http://169.254.1.10. (Refer to the “View Info” section on
page 53 to obtain the IP address of UIP300G.)

3. When the Enter Network Password screen appears, enter the User Name
and Password. Click OK.

Figure 4-6 Web Login Screen

55

Figure 4-7 User Main Page

4. The “User Main Page” screen is displayed. This screen provides
four links:

◆ Phone Settings (allows telephone functions to be configured)

◆ Function Keys (allows function keys to be configured)

◆ Phone Book (allows users to set up a personal telephone book)

◆ Password Change (allows users to change their password)

Click on any of the four links to view or edit the selection. Refer to Figure 4-7
“User Main Page”.

56

Phone Settings Configuration

This option allows users to configure UIP300G settings such as:

◆ Call Duration Timer Display (Enable/Disable)

◆ Call Waiting Tone (Enable/Disable)

◆ Ringer Tone (Tones 1~8)

Figure 4-8 Phone Settings

On the Phone Settings screen, change the settings and then click Submit.

The new settings are stored in the flash memory of the UIP300G and the
page is updated with new settings. If Refresh is clicked before Submit, the
values posted in the page are reset.

57

Function Key Configuration

This option allows users to assign the function keys on the UIP300G.

Select the appropriate function key (Speed Dial, Voice Mail, or Do Not
Disturb) and enter the associated telephone number (if necessary) and
click Submit.

The new settings are stored in the flash memory of the UIP300G and the
page is refreshed with the updated settings. If Refresh is clicked before
Submit, the values posted in the page are reset.

• The Speed Dial key assignment is only available for a telephone number and
not an IP address.

• If Speed Dial is selected, the speed dial number must be entered in the
corresponding phone number field.

• If Voice Mail is selected, the telephone number of the Voice Mail server must
be entered.

• Users cannot assign Voice Mail or DND to more than one function key.

• Enter the “,” to insert a 2 second pause in the assigned number.

Figure 4-9 Function Key Configuration

58

Phone Book

This option allows users to view their phone book and to add, delete and
modify entries in their Phone Book.

To add an entry to the Phone Book:

1. Enter the Name and Phone Number in the appropriate fields on the screen.

2. Beside the Add/Edit/Delete caption, click the arrow on the pulldown menu

and select Add.

3. Click Submit.

To edit an existing entry in the Phone Book:

1. Check the box of the record to be edited.

2. Enter the new Name or new Phone Number in the appropriate fields on
the screen.

3. Beside the Add/Edit/Delete caption, click the arrow on the pulldown menu
and select Edit.

4. Click Submit.

Figure 4-10 Phone Book Configuration

Enter the “,” to insert a 2 second pause in the assigned number to be dialed.

59

To delete an existing Phone Book entry:

1. Check the box of the record to be deleted.

2. Beside the Add/Edit/Delete field, click the arrow on the pulldown menu

and select Delete.

3. Click Submit.

To delete all Phone Book entries:

1. Select DelAll from the pulldown menu.

2. Click Submit.

Password Change

This option allows users to change their password.

Figure 4-11 Password Change

To change the password:

1. Enter the old password in the Current User Password field.

2. Enter the new password in the New User Password field.

The password consists of 6 ~10 digits. If the password entry is not valid, an error
message is displayed. To correct the password, click “Back to User Password
Change” and reenter the passwords.

If the user password change is successful, the user will be prompted to log in
again using the new password.

3. Confirm the new password in the Confirm New Password field.

The new settings are stored in the flash memory of the UIP300G and the
page is refreshed with the updated settings. If Refresh is clicked before
Submit, the values posted in the page are reset.

60

Administrator Configuration

This menu allows Administrative users to review and modify the
network configuration.

Figure 4-12 Web Login Screen

1. Start the web browser.

2. Check the IP address on the telephone and enter that IP address in the
web browser: http://169.254.1.10 (Refer to the “View Info” section on page
53 to obtain the IP address of UIP300G.)

3. When the Enter Network Password screen appears, enter the User Name
and Password. Click OK.

• At default the User Name is admin.

• The password is 6 ~ 10 digits. At default, the Password is 654321.

61

To access the Administrative Configuration screen and modify network and
protocol configurations:

Figure 4-13 Administrative Configuration Main Page

4. The Administrator Configuration screen appears. This screen provides the
following links:

◆ Network Configuration

◆ H.323 Configuration

◆ SNTP Server Configuration

◆ Codec Configuration

◆ Add/Del User and Password

◆ Change Admin Password

◆ Update Firmware

◆ Update Configuration File

5. Click on any of the links to view or edit the related configuration.

62

Network Configuration

This option allows users to modify the following network related items:

◆ DHCP (Enable/Disable)

◆ Phone IP Address

◆ Subnet Mask

◆ Default Gateway IP Address

◆ VLAN (Enable/Disable)

◆ VLAN ID

◆ VLAN Priority

◆ DiffServ (Enable/Disable)

◆ DiffServ Flag

Figure 4-14 Network Configuration

• The new settings are stored in the flash memory of the UIP300G and the
telephone resets.

• Click Refresh before clicking Submit to cancel the changes.

To change a configuration:

1. Modify the information in the field by either entering the new information
or clicking on the pulldown menu and selecting the new option.

2. Click Submit.

63

To change a configuration:

1. Modify the information in the field by either entering the new information
or clicking on the pulldown menu and selecting the new option.

2. Click Submit.

• The new settings are stored in the flash memory of the UIP300G and the
telephone resets.

• Click Refresh before clicking Submit to cancel the changes.

H.323 Configuration

This option allows users to modify the following H.323 related configurations.
H.323 Network Settings PLAR Settings

◆ GK/GW Mode ◆ Dial Tone

◆ GK/GW IP Address ◆ Connection String

◆ GK/GW Port #

◆ RTP Port Base Feature Key Settings

◆ Use Fast Start ◆ DTMF Mode

◆ Redial Key Mode

H.323 Settings ◆ Conference Key Mode

◆ Display Name ◆ Hold Key Mode

◆ E164 Alias (Phone #) ◆ DND Send Busy Signal

◆ H323-ID Alias

◆ LCD Display Type Feature Key DTMF Strings

◆ Calling Party Name Type ◆ Redial DTMF String

◆ CID Display Type ◆ Conference DTMF String

◆ Transfer DTMF String

◆ Hold DTMF String

Figure 4-15 H.323 Configuration

64

SNTP Server

This option allows users to modify the following SNTP (Simple Network
Time Protocol) related configurations.

◆ SNTP (Enable/Disable)

◆ Daylight Savings Time (Enable/Disable)

◆ Time Zone Offset (-12 to +12)

◆ SNTP Server IP Address

Click Refresh before clicking Submit to cancel the changes.

To change a configuration:

1. Modify the information in the field by either entering the new information
or clicking on the pulldown menu and selecting the new option.

2. Click Submit.

Figure 4-16 SNTP Server Configuration

65

Figure 4-17 Codec Configuration

◆ VAD (Enable/Disable)

Click Refresh before clicking Submit to cancel the changes.

To change a configuration:

1. Modify the information in the field by clicking on the pull-down menu and
selecting the new option.

2. Select the Preferred Codec.

3. Click Submit.

The nominal jitter depth must be at least twice as large as the packet size.

Codec Configuration

This option allows users to modify the following voice Codec related
configurations.

◆ Preferred Codec

◆ Acoustic Echo Canceller (Enable/Disable)

◆ Packet Size (ms)

◆ Nominal Jitter Depth (ms)

66

Figure 4-18 Add/Delete User ID and Password

Add/Del User and Password

This option allows users to add or delete the User Name and Password.

To add/delete a user:

1. Enter the User ID and Password.

2. Select Add/Delete from the Add/Del pulldown menu.

• The admin user cannot be deleted.

• This terminal allows two users; the administrator and one additional user.
At default the administrator and user are configured.

• To add a new user, delete the exiting user and then add the new user.

• The new settings are stored in the flash memory of the UIP300G .

• Click Refresh before clicking Submit to cancel the changes.

3. Click Submit.

67

• The new settings are stored in the flash memory of the UIP300G .

• Click Refresh before clicking Submit to cancel the changes.

• When the password has been successfully changed, the “Enter Network
Password” box will prompt you to enter the new password.

3. Enter the new password again in the Confirm Password field.

4. Click Submit.

• The password is 6~10 digits.

• If the password is not valid, an error message is displayed. Return to the
Administrator Password screen by clicking “Back to administrator password
change” and repeat the process.

Change Administrator’s Password

This option allows the administrative user to change their password.

To change the password:

1. Enter the Old Admin Password.

2. Enter the New Admin Password.

Figure 4-19 Administrator Password

68

To update the firmware:

1. Enter the TFTP Server IP Address.

2. Enter the User ID (optional).

3. Enter the Password (optional).

4. Enter the File Name.

5. Click Update.

During Firmware Update, IP telephone MUST not be power cycled. Doing so will
damage the unit.

Update Firmware

This option allows users to update the firmware. Firmware updates can only
be done using the web browser.

Figure 4-20 Update Firmware

69

When the firmware starts updating “Downloading Firmware...” is displayed.

When the firmware file has been downloaded into RAM on the UIP300G,
the checksum calculation starts.

When the checksum calculation has finished, the old firmware is erased
(the second line of the display indicates the sector of the flash being erased).

After the old firmware has been erased, new firmware programming starts
(the percentage of progress is displayed on the second line of the display).

Downloading Firmware...

uip300_enc_ge100.ftp

Calculating Checksum...

Please Wait

Erasing Flash...

5/20

Programming Flash...

75% Completed

When programming is completed, the following message is displayed and the
telephone restarts automatically.

Firmware Update

Completed

70

Figure 4-21 Update Configuration

Update Configuration File

This option allows users to upload a coding profile related configuration file.

To update the configuration file:

1. Enter the TFTP Server IP Address.

2. Enter the User ID (optional).

3. Enter the Password (optional).

4. Enter the Config File Name.

5. Click Update.

71

When the configuration file starts downloading, “Downloading Config...”
is displayed.

Once the configuration file has been downloaded into the RAM on the UIP300G,
the progress message is displayed while the configuration is being updated.

When the configuration update has been completed, “Config File Download
Completed” is displayed and the telephone restarts automatically.

Downloading Config...

uip300_setting.txt

Updating Config...

Config File Download

Completed

72

Appendix

General Information

This appendix provides information about the default setup and configuration
data and provides a setup menu diagram to give users a “roadmap” of the
programming menu structure.

Factory Default Settings

Parameter Default

Handset Volume 2nd level
Speakerphone Volume 2nd level
Headset Volume 2nd level
Ringer Volume 2nd level
Phone Book Empty
Call Log Empty
Call Duration Timer On
Call Waiting On
Ringer Tone Ringer 1
LCD Contrast 8th level
Function Key (5 keys) No Feature Assigned
User Name “user”
User Password 123456
Admin Name “admin”
Admin Password 654321
DHCP Disable
Phone IP Address 169.254.1.10
Subnet Mask

255.255.255.000

Default Gateway IP Address 169.254.1.1
VLAN Disable
VLAN ID 0
VLAN Priority 0
DiffServ Disable
DiffServ Flag 0
Firmware Updated False
Gatekeeper/Gateway Mode GK_MAN_MODE
Gatekeeper/Gateway IP Address 169.254.1.1
Gatekeeper/Gateway Port 1719
RTP Port Base 30000
Use Fast Start No

73

Parameter Default

Display Name “IP Phone”
E.164 Alias (Phone #) 1000
H.323-ID Alias “user”
LCD Display Type DISPLAY_OFF
Calling Party Name Type DISPLAY_NAME
CID Display Type CALLING_PARTY_NAME
Dial Tone INTERNAL
Connection Password String “”
DTMF Mode ALPHANUMERIC
Redial Key Mode CALL_LOGS
Conference Key Mode LOCAL
Hold Key Mode LOCAL
DND Send Busy Signal Yes
Redial DTMF String “**”
Conference DTMF String “**”
Transfer DTMF String “**”
Hold DTMF String “**”
SNTP Disable
Day Light Saving Disable
Time zone offset -6
SNTP server address 192.5.41.40
VAD (G711 A) Disable
Packet Size (ms) (G711 A) 20
Nominal Jitter Depth (ms) (G711 A) 40
Acoustic Echo Canceller (G711 A) Enable
VAD (G711 µ) Disable
Packet Size (ms) (G711 µ) 20
Nominal Jitter Depth (ms) (G711 µ) 40
Acoustic Echo Canceller (G711 µ) Enable
VAD (G723.1) Disable
Packet Size (ms) (G723.1) 60
Nominal Jitter Depth (ms) (G723.1) 120
Acoustic Echo Canceller (G723.1) Enable
VAD (G729.AB) Disable
Packet Size (ms) (G729.AB) 10
Nominal Jitter Depth (ms) (G729.AB) 20
Acoustic Echo Canceller (G729.AB) Enable
Preferred Codec Type G711_Mu

74

Setup Menu Call Logs Incoming

Outgoing

Missed

Phone Book Dial

Add

Edit

Delete

Configuration

Phone

Configuration

Network

Configuration

Call Duration

LCD Contrast

Ringer Type

DHCP

IP Address

Subnet Mask

Default Gateway

VLAN

VLAN ID

Local Date/Time

Restore Factory Setting

Delete Logs...

View Info

Function Key

Setup Menu Tree

75

May be covered under one or more of the following U.S. patents:

4,523,058 4,595,795 4,797,916 5,381,460 5,426,690 5,434,905 5,491,745
5,533,010 5,574,727 5,581,598 5,650,790 5,660,269 5,661,780 5,663,981
5,671,248 5,696,471 5,717,312 5,732,355 5,754,407 5,758,289 5,768,345
5,787,356 5,794,152 5,801,466 5,825,161 5,864,619 5,893,034 5,912,968
5,915,227 5,929,598 5,930,720 5,960,358 5,987,330 6,044,281 6,070,082
6,125,277 6,253,088

©2003 Uniden America Corporation, Fort Worth, Texas

Contain additional foreign articles.

Made in China.