Ubiquiti UBB User Manual
60 GHz Gigabit+ Wireless
Bridge Kit
Model: UBB
• Package Contents
• Installation Requirements
• Hardware Overview
• Hardware Installation
• Aiming
• Connecting Power
• Adopting the UBB
• Software Installation
• Installer Compliance Responsibility
• Specifications
• Safety Notices
• Electrical Safety Information
• Limited Warranty
• Compliance
• Declaration of Conformity
Package Contents
UBB
(Qty. 2)
Ball Joint
Mount (Qty. 2)
Gigabit PoE (48V, 0.32A)
with Mounting Bracket (Qty. 2)
Lock Ring
(Qty. 2)
Metal Strap
Power Cord
(Qty. 2)
(Qty. 2)
System Requirements
• One of the following:
• UniFi Cloud Key (1.0.5 or newer) or UniFi Dream Machine
(1.0.1 or newer)
• Linux, MacOSX, or Microsoft Windows 7/8/10
• Java Runtime Environment 1.6 (1.8 or newer
recommended)
• UniFi Controller software v5.12.x (or newer), available at:
ui.com/download/unifi
• UniFi Network App (iOS or Android™) or Web Browser
(Google Chrome preferred)
Installation Requirements
• Pole-mounting: 7 mm socket wrench or screwdriver
• Wall-mounting: wall fastener (not included)
• The device needs to have clear line of sight to thesky for
proper GPS operation.
• Shielded Category 5 (or above) cabling with drain wire
should be used for all wired Ethernet connections and
should be grounded through the AC ground of the PoE.
We recommend that you protect your networks from
harmful outdoor environments and destructive ESD events
with industrial-grade, shielded Ethernet cable from Ubiquiti.
For more details, visit ui.com/toughcable
• Surge protection should be used for all outdoor installations.
We recommend that you use two Ethernet Surge Protectors,
model ETH-SP-G2, one near the device and the other at
the entry point to the building. The ETH-SP-G2 will absorb
power surges and safely discharge them into the ground.
ETH-SP-G2
UBB
ETH-SP-G2
US-8-150W
LAN
Hardware Overview
1
System LED
Color State Status
White Flashing Initializing.
Steady Factory defaults, waiting for
White/
Alternating Device is busy; do not touch or
Blue
Blue Steady Successfully integrated into a
Flashing This is used to locate a device.
integration.
unplug it. This usually indicates
that a process such as a firmware
upgrade is taking place.
network and working properly.
When you click Locate in the UniFi
Network Controller software, the
LED will flash blue. The software
will also display the location of the
device on themap.
Item Description
Resets to factory defaults. The device
should be running after bootup is
complete. Press and hold the Reset button
for about 10 seconds until the LED starts
flashing and then becomes solidly lit. After
Reset Button
Ethernet Port
a few seconds, the LED will turn off, and the
device will automatically reboot.
This Gigabit Ethernet port is used to
connect the power and should be
connected to the LAN and DHCP server.
2 3
Note: The UBB radios are pre-paired.
If a link is lost due to configuration
changes, you can reset both UBB
radios to re-establish the link.
Hardware Installation
For each UBB radio, go to the appropriate mounting
instructions: Pole Mounting or “Wall Mounting”.
Pole-Mounting
1.
2.
3.
4.
Wall Mounting
The device must be mounted directly to a wood stud or other
structurally stable surface to avoid damage to the mounting
hole when you adjust the aim.
Optional Accessory
To enhance stability, you can use the NanoBeam® Wall Mount
Kit, model NBE-WMK (soldseparately).
Note: Center screw included. Two optional screws (not
included) provide additional stability.
Installation Instructions
1.
Loading...