Ubiquiti ES-16-150W Quick Installation Guide
Managed PoE+ Gigabit Switch
with SFP
Model: ES-16-150W
Introduction
Thank you for purchasing the Ubiquiti Networks® EdgeSwitch™.
This Quick Start Guide is designed to guide you through the
installation and also includes the warranty terms.
Package Contents
EdgeSwitch ES-16-150W
Power Cord Mount Brackets
Mounting Screws
(#10-32 x 5/8", Qty. 4)
TERMS OF USE: All Ethernet cabling runs must use CAT5 (or above). It is the customer’s
responsibility to follow local country regulations, including operation within legal frequency
channels, output power, indoor cabling requirements, and Dynamic Frequency Selection
(DFS) requirements.
(Qty. 2)
Cage Nuts
(#10-32 x 5/8", Qty. 4)
Bracket Screws
Rubber Feet
(Qty. 4)
(M4, Qty. 8)
Quick Start
Managed PoE+ Gigabit Switch
withSFP
Model: ES-16-150
Guide
Installation Requirements
• Phillips screwdriver (for rack or wall mounting)
• Standard-sized, 19" wide rack with a minimum of 1U height
available (for rack mounting)
• For indoor applications, use Category 5 (or above) UTP
cabling approved for indoor use.
• For outdoor applications, shielded Category 5 (or above)
cabling should be used for all wired Ethernet connections
and should be grounded through the AC ground of the
power supply.
We recommend that you protect your networks from
harmful outdoor environments and destructive ESD events
with industrial-grade, shielded Ethernet cable from Ubiquiti
Networks. For more details, visit www.ubnt.com/toughcable
WARNING: To reduce the risk of fire or electric shock,
do not expose the switch to rain or moisture.
Note: Although the cabling can be located outdoors,
the EdgeSwitch itself should be housed inside a
protective enclosure.
Hardware Overview
Front Panel Ports
SFP 1-2
Port Description
RJ45 1-16
SFP 1-2
RJ45 ports support 10/100/1000 Ethernet
connections.
Hot-swappable SFP ports support 1 Gbps
connections.
RJ45 1-16
Front Panel LEDs
System
RJ45:
PoE
SFP:
Speed/Link/Activity
LED State Status
White Ready for Use
System
Blue
Off No PoE
PoE
Amber IEEE 802.3af/802.3at
Green 24V Passive
Off No Link
RJ45 1-16
Speed/
Amber
Link/
Act
Green
Off No Link
Speed/
Link/
SFP 1-2
Act
Green
RJ45:
Speed/Link/Activity
Bootup in Progress
Flashing Indicates Reset
to Factory Defaults
Link Established at
10/100Mbps
Flashing Indicates Activity
Link Established at
1000Mbps
Flashing Indicates Activity
Link Established at 1Gbps
Flashing Indicates Activity
Front Panel Button
Button Description
There are two methods to reset the
EdgeSwitch to factory defaults:
Runtime Reset (Recommended)
The EdgeSwitch should be running after
bootup is complete, and the System LED
is white. Press and hold the Reset button.
The EdgeSwitch will reboot, and the System
LED becomesblue after three seconds.
Continue to hold the Reset button for
about 15seconds until the System LED
Reset
flashes blue for two seconds. This indicates
that the EdgeSwitch has reset to its
factorydefaults.
Power-on Reset
1. Disconnect the Power Cord from the
2. While connecting the Power Cord to
Reset
EdgeSwitch.
the EdgeSwitch, hold the Reset button
for about 15seconds until the System
LED flashes blue for two seconds. This
indicates that the EdgeSwitch has reset
to its factory defaults.
Back Panel Console Port
Console
Port Description
RJ45 serial console port for Command
Line Interface (CLI) management. Use an
RJ45-to-DB9, serial console cable, also
known as a rollover cable, to connect
the Console port to your computer. Then
Console
configure the following settings as needed:
• Baud rate 115200
• Data bits 8
• Parity NONE
• Stop bits 1
• Flow control NONE
Hardware Installation
The EdgeSwitch can be placed on a horizontal surface,
mounted in a rack, or mounted on a wall.
WARNING: FAILURE TO PROVIDE PROPER VENTILATION
MAY CAUSE FIRE HAZARD. KEEP AT LEAST 20 MM OF
CLEARANCE NEXT TO THE VENTILATION HOLES FOR
ADEQUATE AIRFLOW.
Place the Rubber Feet on the bottom of the EdgeSwitch if you
do not plan to mount it. For rack or wall mounting, follow the
appropriate steps:
*640-00174-03*
640-00174-03
Rack Mounting
1. Attach the Mount Brackets to the EdgeSwitch using the
eight Bracket Screws, positioning the brackets as shown
below.
2. Attach the EdgeSwitch to the rack using the four Mounting
Screws. (If the rack has square slots, then use the Cage Nuts
with the Mounting Screws.)
Wall Mounting
1. Attach the Mount Brackets to the EdgeSwitch using the
eight Bracket Screws, positioning the brackets as shown
below.
2. Secure the EdgePower to the wall using the appropriate
fasteners and anchors (not included) for the wall.
Loading...