TM
Owner’s Manual
for the turbochef high h conveyor 1618, 2020, and 2620 ovens
© 2008-2015 TurboChef Technologies, Inc.
For further information, call
800.90TURBO or
+1 214.379.6000
The information contained in this manual is important for the proper installation, use, maintenance, and repair of this oven. Follow these procedures and instructions to help ensure satisfactory baking results and years of trouble-free service.
Errors – descriptive, typographic, or pictorial – are subject to correction. Specifications are subject to change without notice.
Please carefully read this manual and retain it for future reference.
Table of Contents
Safety Information
Important Safety Information - Please Read First |
i |
General Safety Information |
i |
Reducing Fire Risk |
ii |
Preventing Oven Damage |
ii |
Grounding Instructions |
ii |
Power Cord Replacement |
ii |
Specifications and Installation
HhC 1618 Dimensions |
1 |
HhC 1618 Electrical Specifications |
1 |
HhC 2020 Dimensions |
2 |
HhC 2020 Electrical Specifications |
2 |
HhC 2620 Dimensions |
3 |
HhC 2620 Electrical Specifications |
3 |
Packaging |
4 |
Certifications |
4 |
Construction |
4 |
Installation Instructions |
4 |
Delivery and Initial Inspection |
4 |
Lifting the Oven |
4 |
Oven Location and Placement |
4 |
Installation Near Open Heat Source |
5 |
Ventilation Requirements |
5 |
Cleaning
Daily Cleaning Instructions |
6 |
Weekly Cleaning Instructions |
7-9 |
Standard Oven Operation
Oven Controls |
10 |
Cooking |
11 |
Editing a Cooking Profile |
13 |
Changing a Cooking Profile Name |
13 |
Adjusting the Belt Speed |
14 |
Adjusting the Temperature |
14 |
Adjusting the Top and Bottom Air |
14 |
Oven Modes
Config Mode |
15 |
Smart Card Screen (Loading a Menu) |
15 |
Accessing the Fault Count Screen |
15 |
Accessing the Setup Mode |
15 |
Setup Mode |
15 |
Changing the Display Temperature |
16 |
Changing the Belt Direction |
16 |
Edit Options Screen |
16 |
Changing the Speaker Volume |
16 |
Info Screen |
17 |
Updating the Firmware |
17 |
Troubleshooting |
18 |
Replaceable Parts |
20 |
North America Limited Warranty |
21 |
International Limited Warranty |
24 |
i
Important Safety Information – Please Read First
Improper installation, adjustment, alteration, service, or maintenance of this equipment can cause property damage, injury, or death. Thoroughly read the installation, operating, and maintenance instructions before installing or servicing this equipment. Strictly adhere to the following safety information to reduce the risk of:
oDamage to the oven
oDamage to property near the oven
oPersonal injury
oBurns
oFire
oElectric shock
General Safety Information
oUse this appliance only for its intended uses as described in this manual.
oOnly qualified service personnel should service this appliance. Contact the nearest authorized service facility for examination, repair, or adjustment.
oAlways ensure the oven is disconnected from the power supply before servicing, repairing, or adjusting any components or parts.
oThis appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or
instruction concerning use of the appliance by a person responsible for their safety.
DO NOT place the cord near heated surfaces.
DO NOT store or use flammable vapors or liquids (e.g., gasoline) in the vicinity of this appliance.
DO NOT allow children to use this appliance. Children should be supervised to ensure that they do not play with the appliance
DO NOT place corrosive chemicals or vapors in this appliance. It is not designed for industrial or laboratory use.
DO NOT operate this appliance if it:
Has a damaged cord or plug
Is not working properly
Has been damaged or dropped
DO NOT cover or block any openings on this appliance.
DO NOT store this appliance outdoors.
DO NOT use this appliance near water.
DO NOT immerse this appliance or any of its components (e.g., cord, plug, etc.) in water.
DO NOT let the cord hang over the edge of a table or counter.
INFORMATION SAFETY
ii SAFETY INFORMATION
Reducing Fire Risk
If materials inside the oven ignite or if smoke is observed,
1.Turn off the oven.
2.Disconnect the power cord or shut off power at the fuse/circuit breaker panel.
o Carefully attend the oven if paper, plastic, or other combustible materials are placed inside the oven to facilitate cooking.
DO NOT leave items in the cook cavity when the oven is not in use.
DO NOT cook items wrapped in cling wrap or plastic film.
DO NOT overcook food.
Preventing Oven Damage
oWhen servicing this appliance, do not tear insulation to get to components. Rather, find the edge of the insulation and remove the tape that holds it in place.
oClean the oven daily.
oClean the oven only with TurboChef Oven Cleaner.
DO NOT clean with a water jet.
DO NOT allow cleaning solution or water to remain in the cook cavity longer than necessary.
Grounding Instructions
WARNING: Improper grounding increases the risk of electric shock.
This appliance must be grounded. The cord is equipped with a grounding wire and plug, which in the event of an electrical short circuit, reduce the risk of electric shock by providing an escape wire for the electric current. The wire must be plugged into an outlet that is properly installed and grounded.
Consult a qualified electrician or serviceman to determine whether or not the appliance is properly grounded.
DO NOT use an extension cord. If the power supply cord is too short, request a qualified electrician or serviceman to install an outlet near the appliance.
Power Cord Replacement
To avoid potential hazards, only the manufacturer, its service agent, or a similarly-qualified person should replace a damaged power cord.
8.5” (216 mm)
31.7” (805 mm)
Figure 1: HhC 1618 Oven Dimensions - Side
48.1” (1222 mm) with 6” (152 mm) extensions 
Figure 2: HhC 1618 Oven Dimensions - Top
36” (914 mm)
17.0” 13.0” (432 mm)
(330 mm)
4.0” (102 mm)
Figure 3: HhC 1618 Oven Dimensions - Front (Single)
13.0”
(330 mm)
30.0”
(762 mm)
13.0”
(330 mm)
Figure 4: HhC 1618 Oven Dimensions - Front (Double)
13.0” (330 mm)
43.0” (1092 mm)
13.0”
(330 mm)
13.0” (330 mm)
Figure 5: HhC 1618 Oven Dimensions - Front (Triple)
HhC 1618 Dimensions
Exterior
Height |
13.0” (330 mm) |
--with legs |
17.0” (432 mm) |
Width |
36.0” (914 mm) |
Depth |
31.7” (805 mm) |
Conveyor
Length |
36.0” |
(914 mm) or 48” (1219 mm) |
Width |
16.0” |
(406 mm) |
Electrical Specifications
North America 1 Phase 208/240 VAC 50/60 Hz
37 amp current draw Max Input: 7.5 kW 3-wire supply NEMA 6-50P plug
50-amp max circuit breaker protection
Europe/Asia (220-240 VAC) 3 Phase
220-240 VAC 50/60 Hz
23 amp current draw Max Input: 7.5 kW 4-wire supply IEC60309 4-pin plug
30-amp max circuit breaker protection
Europe/Asia (380-415 VAC) 3 Phase
380-415 VAC 50/60 Hz
12 amp current draw Max Input: 7.5 kW 5-wire supply IEC60309 5-pin plug
30-amp max circuit breaker protection
1
INSTALLATION AND SPECIFICATION
2 SPECIFICATION AND INSTALLATION
8.5” (216 mm)
35.7” (907 mm)
Figure 1: HhC 2020 Oven Dimensions - Side
60.1” (1527 mm) with extensions
Figure 2: HhC 2020 Oven Dimensions - Top
48.3” (1227 mm)
17.0” 13.0” (432 mm)
(330 mm)
4.0” (102 mm)
18.4” (467 mm) 
Figure 3: HhC 2020 Oven Dimensions - Front (Single)
13.0” (330 mm)
30.0”
(762 mm)
13.0”
(330 mm)
Figure 4: HhC 2020 Oven Dimensions - Front (Double)
13.0” (330 mm)
43.0”
(1092 mm)
13.0”
(330 mm)
13.0”
(330 mm)
HhC 2020 Dimensions
Exterior
Height |
13.0” (330 mm) |
|
with legs |
17.0” (432 mm) |
|
Width |
48.3” |
(1227 mm) |
Depth |
35.7” |
(907 mm) |
Conveyor
Length |
48.3” |
(1227 mm) |
Width (Single) |
20.0” |
(508 mm) |
Width (50/50) 9.5” / 9.5” (241 mm / 241 mm) Width (70/30) 15” / 4” (381 mm / 102 mm)
Electrical Specifications
North America 3 Phase 208/240 VAC 50/60 Hz
40 amp current draw Max Input: 14.4 kW 4-wire supply
NEMA 15-50P plug (4-pin IEC60309 available by special order)
50-amp max circuit breaker protection
Europe/Asia (220-240 VAC) 3 Phase
220-240 VAC 50/60 Hz
40 amp current draw Max Input: 14.4 kW 4-wire supply IEC60309 4-pin plug
64-amp max circuit breaker protection
Europe/Asia (380-415 VAC) 3 Phase
380-415 VAC 50/60 Hz
20 amp current draw Max Input: 14.4 kW 5-wire supply IEC60309 5-pin plug
32-amp max circuit breaker protection
Figure 5: HhC 2020 Oven Dimensions - Front (Triple)
17.0” (432 mm)
8.5” (216 mm)
4.0” (102 mm)
4.0” (112 mm)
24.0” (610 mm) 
41.7” (1059 mm)
Figure 6: HhC 2620 Oven Dimensions - Side
48.3” (1227 mm)
41.7” (1059 mm)
Figure 7: HhC 2620 Oven Dimensions - Top
48.3” (1227 mm)
17.0” 13.0” (432 mm)
(330 mm)
4.0” (102 mm)
18.4” (467 mm) 
Figure 8: HhC 2620 Oven Dimensions - Front (Single)
13.0”
(330 mm)
30.0”
(762 mm)
13.0” (330 mm)
Figure 9: HhC 2620 Oven Dimensions - Front (Double)
13.0”
(330 mm)
43.0”
(1092 mm)
13.0” (330 mm)
13.0” (330 mm)
Figure 10: HhC 2620 Oven Dimensions - Front (Triple)
HhC 2620 Dimensions
Exterior
Height |
13.0” (330 mm) |
--with legs |
17.0” (432 mm) |
Width |
48.3” (1227 mm) |
Depth |
41.7” (1059 mm) |
Conveyor
Length |
48.3” |
(1227 mm) |
Width (Single) |
26.0” |
(660 mm) |
Width (50/50) 12.5” / 12.5” (318 mm / 318 mm) Width (70/30) 17” / 8” (431 mm / 203 mm)
Electrical Specifications
North America 3 Phase 208/240 VAC 50/60 Hz
40 amp current draw Max Input: 14.4 kW 4-wire supply
NEMA 15-50P plug (4-pin IEC60309 available by special order)
50-amp max circuit breaker protection
Europe/Asia (220-240 VAC) 3 Phase
220-240 VAC 50/60 Hz
40 amp current draw Max Input: 14.4 kW 4-wire supply IEC60309 4-pin plug
64-amp max circuit breaker protection
Europe/Asia (380-415 VAC) 3 Phase
380-415 VAC 50/60 Hz
20 amp current draw Max Input: 14.4 kW 5-wire supply IEC60309 5-pin plug
32-amp max circuit breaker protection
3
INSTALLATION AND SPECIFICATION
Loading...