Tronic KH 3157 User Manual [pl]
BAT TERY CHARGER
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions
of the device.
Przed przeczytaniem proszę rozłożyć stronę z ilustracjami, a następnie proszę zapoznać się z wszystkimi
funkcjami urządzenia.
Olvasás előtt kattintson az ábrát tartalmazó oldalra és végezetül ismerje meg a készülék mindegyik
funkcióját.
Kompernaß GmbH
Burgstraße 21
D-44867 Bochum (Germany)
Last Information Update · Stan informacji
Információk állása: 09 / 2007 · Ident.-No.: T4X092007 - 4 A
A
T4X
BAT TERY CHARGER
Operation and Safety Notes
AKKUMULÁTORTÖLTŐ
KÉSZÜLÉK
Kezelési és biztonsági utalások
PRZYRZĄD DO ŁADOWANIA
AKUMULATORÓW
Wskazówki dotyczące obsługi i bezpieczeństwa
A
GB Operation and Safety Notes Page 5
PL Wskazówki dotyczące obsługi i bezpieczeństwa Strona 13
HU Kezelési és biztonsági utalások Oldal 21
A
1 2 3 4
B
C
8
9 10
11
1415
57 6
11
12
13
Table of Content
Introduction
For your safety ..............................................................................................................Page 6
Proper Use .....................................................................................................................Page 6
Delivery Contents .........................................................................................................Page 6
Component description ................................................................................................Page 6
Technical Data ..............................................................................................................Page 7
Safety
Safety information ........................................................................................................Page 7
Product features ............................................................................................................Page 9
Operation
Preparing for use ..........................................................................................................Page 9
Connection ....................................................................................................................Page 9
Disconnecting................................................................................................................Page 9
Select charging mode ..................................................................................................Page 9
Reset / deleting settings ................................................................................................Page 10
Switching over between modes 1, 2 and 3 ...............................................................Page 10
Mode 1 (14.4 V / 0.8 A) .........................................................................................Page 10
Mode 2 (14.4 V / 3.6 A) .......................................................................................Page 10
Mode 3 (14.7 V / 3.6 A) .........................................................................................Page 10
Regenerating / charging empty (used, overcharged) batteries ................................Page 11
Protective function of the device ..................................................................................Page 11
Overheating protection ................................................................................................Page 11
Maintenance and care ..................................................................................Page 11
Disposal ......................................................................................................................Page 11
Information
Servicing ........................................................................................................................Page 11
Declaration of conformity / Manufacturer ..................................................................Page 12
5 GB
6 GB
Introduction
The following pictogrammes / symbols are used in these operating instructions:
Read the operating instructions!
Always heed warning labels and
safety instructions!
Caution - Danger of electric shock! Hazardous
voltage – danger to life!
Explosive material!
Risk of fire!
Battery charger T4X
for rechargeable batteries / batteries from
1.2 Ah to 120 Ah
Q
Introduction
Q
For your safety
Please carefully read these operating in-
structions and fold out the page with the
illustrations.Observe this information
exactly when putting the appliance into operation.
If you have any further
questions regarding use, please contact the service
department responsible for your country. Keep these
operating instructions in a safe place and hand them
over to anyone to whom you pass on the appliance.
W
V
Watts (effective power)
Volt (AC)
~
Proper procedure and handling.
Keep children and other unauthorised personnel
at a safe distance when using electrical tools.
Dispose packaging and appliance in an
environmentally-friendly way!
Operate the charging appliance in a warmed and
well ventilated room. Any incorrect or improper use
leads to loss of the warranty. The manufacturer
takes no responsibility for damage(s) arising out of
usage that is contrary to the instructions laid down.
The appliance is not meant for commercial use.
Q
Delivery Contents
Check the appliance and all accessories for damage immediately after unpacking. Do not put a defective appliance or parts into operation. Please
contact the resonsible service department for
a replacement.
1 Charger TRONIC T4X
2 Quick / contact clamps (1 red, 1 black)
1 Operating manual
Guarantee documents
Q
Proper Use
The TRONIC T4X is a primarily mains-connected
(working with measuring and control functions)
charging station with pulse trickle charge function,
suitable for charging and trickle charging 12 V lead
accumulators (batteries) with electrolyte solution or
gel. The charger has a circuit-breaker as protection
against sparking and overheating.
Q
Component description
1
STANDBY LED display :“STANDBY“ (standby)
2
LED display „Mode 1“
3
LED display „Mode 2“
4
LED display „Mode 3“
5
LED display „incorrect polarity/fault“
6
LED display „fully charged“
7
LED display „Charging process active“
7 GB
Introduction / Safety
T4X KH 3157
220 V-240 V AC ~ 50 Hz / 60 Hz · 55 W
12 V DC
0,8 / 3,6 A · IP65
Polarity: red clamp (+), black clamp (-)
Date of manufacture: 02/2008
WARNING! Explosive gases - prevent
flames and sparks. Before charging,
study instruction sheet. Disconnect
supply before making or breaking
battery connections. Provide for good
ventilation.
Kompernaß GmbH · D- 44867 Bochum · Germany · www.kompernass.com
Q
8
Selection button „MODE“
9
Charging station
10
Mains cable with power plug
11
Fixing holes
12
„+“-Pole connection cable (red), incl. ring shoe
13
„–“-Pole connection cable (black), incl. ring shoe
14
„+“-Pole quick-contact terminal (red), incl. red
fixing screw
15
„–“-Pole quick-contact terminal (black), incl.
black fixing screw
Q
Technical Data
Input voltage: 220 - 240 V ~ 50 / 60 Hz
Starting current: < 25 A
Input current: max. 0.6 A (Effective value)
Power
consumption: 55 W
Return current*: < 5 mA (no AC input)
Nominal voltage: 12 V DC
Nominal current: 0,8 / 3,6 A
Charging voltage: 14.4 V ± 0.25 V or
14.7 V ± 0.25 V
Charging current: max. 3.6 A (3.6 A ± 10 % or
0.8 A ± 10 %)
Noise value**: max. 150 mV
Battery type: 12 V lead acid battery
1.2 Ah - 120 Ah
Type of housing
protection: IP 65 (dustproof, waterproof)
Dimensions: 180 x 62 x 40 mm
(L x W x H)
Weight: 0.5 kg approx.
Noise level: < 50 dB (A) (tested from a
distance of 50 cm)
* = Return current is the current used by the
charging station battery, when no mains current is connected.
** = Noise value is the disturbance of current and
voltage.
Q
Safety
Safety information
m Danger! Avoid danger to life and limbs
caused by improper use!
J Do not operate the appliance with a damaged
cable, power cord or plug.
m CAUTION! A damaged power cord causes
danger to life by electric shock.
J If damaged, have the power cord j repaired by
authorised and trained technicians only! Please
contact the service department for your country!
J
the potential danger in the handling of electrical
J
can leak from the battery during the charging
J
vents can be ignited when using the charging
m Danger of chemical burns! Protect your
Do not allow toddlers or children
near the charging station without
super-vision! Children cannot assess
equipment.
Explosion hazard! Protect your-
self from a highly explosive oxyhydrogen gas reaction! Gaseous hydrogen
and discharging process. Oxyhydrogen gas is
an explosive mixture of gaseous hydrogen and
oxygen. The result is the so-called oxyhydrogen
reaction upon contact with open fire (flames,
embers or sparks)! Carry out the charging or
discharging procedure in a wellventilated room
protected from the weather. Make sure that there
are no sources of open fire (flames, embers or
sparks) in the vicinity when charging or discharging batteries!
Danger of explosion and fire!
Make sure that explosive and flammable substances e.g. petrol or sol-
station!
eyes and skin against chemical burns caused
by acid (sulphuric acid) upon contact with the
battery! Do not look directly at the connected
battery and use the following: acid-resistant
safety glasses, protective clothing and gloves!
If your eyes or skin come into contact with sulphuric acid, rinse the affected part of the body
with plenty of clear running water and seek
immediate medical assistance!
8 GB
Safety
J Protect yourself from an elec-
tric shock! When connecting the
charging station, use a screwdriver
and a spanner with an insulated handle!
J Only use the charging station for charging and
discharging undamaged 12 V lead batteries
(with electrolyte solution or gel)!
J Do not use the charging station for charging or
trickle-charging batteries without recharging
properties.
J Do not use the charging station for charging or
trickle-charging a damaged or frozen battery!
J In case of permanently installed batteries, make
sure that the vehicle is not in use and is in a secure, stationary position! Switch off the ignition
and select a parking position, apply the parking
brake (e.g. cars)or a retaining rope (e.g. boats)!
J When connecting the charging station to the
battery, avoid short-circuiting. Connect the minus
pole connecting cable only to the minus pole
of the battery or to the car body. Connect the
plus pole connecting cable only to the plus pole
of the battery!
J Before connecting to the mains, make sure that
the mains current is equipped with standard
230 V ~ 50 Hz, PEN conductor, a 16 A fuse
and a residual-current circuit-breaker!
J Only touch the power cord j in the insulated
area at the power plug upon contact with the
socket outlet with earthing contact!
J Only touch the pole connecting cables („–“
und „+“) in the insulated area!
J Only connect to the battery and the socket out-
let with earthing contact of the mains if it is fully
protected against moisture!
J Only carry out the assembly, maintenance and
servicing of the charging station when it is disconnected from the power supply!
J Do not position the charging station near a fire
or subject it to heat or to long-term temperatures
exceeding 50° C! The output capacity of your
charging station is automatically reduces at
high temperatures.
J Do not damage any leads or connections for
fuel, electricity, brake systems, hydraulics, water
or tele-communications when attaching the
charging station with bolts! Otherwise there
will be a danger to life and limbs!
J Make sure that the plus pole connecting cable
has no contact with the fuel line (e.g. petrol line)!
J Ensure that the mains power socket is at all times
freely accessible so that in a case of emergency
the appliance can be quickly separated from
the power source.
J Attention! Avoid damage caused by improper
use!
J Only use the charging station with the original
parts provided!
J Do not cover the charging station with objects!
J Place the battery in a well-ventilated location
during charging.
J Protect the electrical contacts of the battery
against short-circuiting!
J Only connect the charging station to a socket
outlet with earthing contact equipped with a residual-current circuit-breaker when using outdoors.
J Do not place the charging station driectly on or
next to the battery!
J After completing the charging and floating charge
operation on a battery permanently installed in
the vehicle, first disconnect the cable of the
negative (minus) pole (black) of the charger
from the negative (minus) pole of the battery.
J In case of malfunction or damage, immediately
disconnect the charging station from the mains!
J Have the charging station repaired by authorised
and trained specialists only! Please contact the
service department for your country!
J Before connecting the charging station, read
the information on battery maintenance in the
operating instructions of the battery!
J Before connecting the charging station to a
battery permanently installed in a vehicle, read
the information on electrical safety and maintenance in the operating instuctions of the vehicle!
J Do not subject the battery to mechanical
loads!
J When the charging station is not in use, discon-
nect it from the power supply!
9 GB
Safety / Operation
Q
Product features
This appliance has been designed for charging a
variety of SLA batteries (sealed lead acid batteries),
as mainly used in cars, motorbikes and several other
vehicles. They may be of types e.g. WET (with liquid
electrolyte), GEL (with mit gel-type electolyte) or AGM
(absorbed glass mat) batteries. Their capacity ranges
from 12 V / 1.2 Ah to 12 V / 120 Ah.
A special design of the appliance (also named
„three-phase-charging strategy“) enables the recharging of the batttery to almost 100 % of its original
capacity. Furthermore, a long-term connection of the
battery to the charging station can take place to
keep the battery in optimal condition when not in
use, without it being damaged in the process.
Q
Operation
Q
Preparing for use
m Caution! Danger of electric shock!
Only install, maintain and service the appliance
when it is disconnected form the mains!
Working safely
j When putting the appliance into operation,
select a suitable place to do so.
j Take your time when carefully preparing to put
the appliance into operation. Put all compoments
and any additionally required tools or materials
well arranged and within easy reach.
j Always be alert and pay attention to what you
are doing. Be sensible when working and do
not operate the charging station if you lack the
ability to concentrate or do not feel well.
Q
Connection
j Before starting the charging or discharging
procedure on a permanently installed battery
in a vehicle, first disconnect the minus pole con-
necting cable (black) of the vehicle from the
minus pole of the battery. The minus pole of the
battery is usually connected to the car body.
j Then disconect the plus pole connecting cable
(red) of the vehicle from the plus pole of the
battery.
j Then first connect the „+“ pole quick-contact
clamp (red)
14
of the charging station to the
plus pole („+“ pole) of the battery.
j Connect the „–“ pole quick-contact clamp (black)
15
to the „–“ pole of the battery.
j Connect the power cord
10
of the battery
charging station to the socket oulet with earthing
contact of the power supply.
Q
Disconnecting
j Disconnect the appliance from the power supply.
j Disconnect the „–“ pole quick-contact clamp
15
(black)
from the „–“ pole of the battery.
j Disconnect the „+“ pole quick-contact clamp
14
(red)
from the „+“ pole of the battery.
j Reconnect the plus pole connecting cable of
the vehicle to the plus pole of the battery.
j Reconnect the minus pole connecting cable of
the vehicle to the minus pole of the battery.
Q
Select charging mode
For charging various batteries at different ambient
temperatures you can choose between three different
charging modes. Select the most efficient and suitable charging mode for charging the battery.
In comparison with conventional battery charging
stations, this appliance has a special function for
reusing an empty battery or rechargeable battery.
You can recharge an empty battery / rechargeable
battery. Safe charging is ensured by means of a
protection function against incorrect connection and
short circuiting. Due to the installed electronics, the
charging station does not begin operation directly
after connecting the battery, but only starts after a
charging mode has been selected.
10 GB
Operation
This avoids sparking, which often occurs when connecting. Furthermore, this device is also controlled
by an internal MCU (Micro-Computer-Unit), which
makes it faster, more powerful and more reliable.
Q
Reset / deleting settings
After connection to the power supply, the appliance
automatically returns to its basic setting and remains
in STANDBY mode
Q
Switching over between
modes 1, 2 and 3
j Press the selection button MODE 8 repeatedly
to display the charging modes in the following
order: Ready STANDBY, MODE1
, MODE3
If you press the selector button
and start the next cycle.
8
automatically switches over to the next mode and
begins operation in that mode. However, if a battery
is not disconnected from the charging station after
a full charge, the appliance remains in trickle-charge
mode, even if the user switches over to another mode.
This protects the battery from being damaged.
Q
Mode 1 (14.4 V / 0.8 A)
This mode is suitable for charging small batteries
with a capacity below 14 Ah.
j Press the selection button MODE
mode 1. After doing so, the corresponding LED
display
2 lights up. If you do not activate
an-other process afterwards, the electronic system will automatically start the charging process
together with the LED display
current of) 0.8 A ± 10 %.
If the procedure runs without any problems, the
LED display
7 remains on during the entire
charging process, until the battery is fully charged
at 14.4 V / ± 0.25 V. When the battery is fully
charged, LED display
6 lights up and LED
, MODE2
,charging mode
8
, to select
7 at (with a
display
7 goes out. The floating current is now
available for the battery.
Q
Mode 2 (14.4 V / 3.6 A)
This mode is mainly used for charging batteries with
a large capacity exceeding 14 Ah under normal
conditions.
j Press the selection button MODE
8
, to activate
mode 2. If you do not activate another process
afterwards, the electronic system, together with
LED display
3 starts the charging process
at (with a current of) 3.6 A ± 10 % (3.6 A).
If the procedure runs without any problems, the
LED display
7 remains on during the entire
charging process, until the battery is fully charged
at 14.4 V / ± 0.25 V. When the battery is fully
charged, LED display
display
7 goes out. The floating current is
6 lights up and LED
now available for the battery.
Q
Mode 3 (14.7 V / 3.6 A)
This mode is used for charging batteries with a
greater capacity than 14 Ah in cold conditions or
for several AGM batteries with more than 14 Ah.
j Press the selection button MODE
8
, to activate
mode 3. As soon as you have selected the suitable charging mode, the corresponding LED
display
4 lights up immeditely. If you do not
take any further action, the electronic system
starts the charging process with a set delay. In
this mode the charging current is identical to
that of „Mode 2“.
If the procedure runs without any problems, the
LED display
7 lights up, the electronic stystem is active and remains in this condition until
the battery is charged to approx. 14.7 V. As
soon as this is reached, the charging station
switches over to trickle-charging function. Now
LED display
6
7 goes out and LED display
lights up to indicate the current status.
Loading...