Trimble Duo Installation Manual

Trimble Duo

TRANSFORMING THE WAY THE WORLD WORKS

INSTALLATION GUIDE

FEDERAL COMMUNICATION COMMISSION INTERFERENCE STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment o and on, the user is encouraged to try to correct the interference by one of the
following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit dierent
from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution:

Any changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to
operate this equipment.

This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Radiation Exposure Statement:

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
This equipment should be installed and operated with minimum distance 20cm between the radiator &
your body.

2

Model: Trimble Duo
P/N : L019-0517
Input : 12V 1.5A
Contains FCC ID : NKS-DUO-LTE
Contains FCC ID : NKS-DUO-WIFI

RoHS

INDUSTRY CANADA STATEMENT

This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may cause undesired operation of the device.
Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes:

•l’appareil ne doit pas produire de brouillage, et

•l’utilisateur de l’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
FOR MOBILE DEVICE (>20cm from body / low power)

Radiation Exposure Statement:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum dis­tance 20cm between the radiator & your body.
Déclaration d’exposition aux radiations:
Cet équipement est conforme aux limites d’exposition aux rayonnements IC établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un
minimum de 20 cm de distance entre la source de rayonnement et votre corps.

FOR WLAN 5GHZ DEVICE:

Caution: The device for operation in the band 5150–5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;

Avertissement: Les dispositifs fonctionnant dans la bande de 5 150 à 5 250 MHz sont réservés uniquement pour une utilisatin à l’intérieur an de réduire les risques de

brouillage préjudiciable aux systèmes de satellites mobiles utilisant les mêmes canaux

End Product Labeling FOR MOBILE DEVICE USAGE (>20cm/low power)
This transmitter module is authorized only for use in device where the antenna may be installed such that 20 cm may be maintained between the antenna and users. The nal
end product must be labeled in a visible area with the following: “Contains IC:1756A-DUOLTE & Contains IC:1756A-DUOWIFI”.

Plaque signalétique du produit nal

Ce module émetteur est autorisé uniquement pour une utilisation dans un dispositif où l’antenne peut être installée de telle sorte qu’une distance de 20cm peut être main­tenue entre l’antenne et les utilisateurs. Le produit nal doit être étiqueté dans un endroit visible avec l’inscription suivante: “Contient des IC: Contains IC:1756A-DUOLTE &
Contains IC:1756A-DUOWIFI”.

Manual Information To the End User

The OEM integrator has to be aware not to provide information to the end user regarding how to install or remove this RF module in the user’s manual of the end product
which integrates this module. The end user manual shall include all required regulatory information/warning as show in this manual.

Manuel d’information à l’utilisateur nal

L’intégrateur OEM doit être conscient de ne pas fournir des informations à l’utilisateur nal quant à la façon d’installer ou de supprimer ce module RF dans le manuel de
l’utilisateur du produit nal qui intègre ce module.
Le manuel de l’utilisateur nal doit inclure toutes les informations réglementaires requises et avertissements comme indiqué dans ce manuel.

3

TABLE OF CONTENTS

Important Safety Considerations 5

Part List 6

System Overview 9

Diagnostic Cable Installation 16

Hardware Installation 20

Indicator Lights 23

Activation 24

System Information 35

Troubleshooting 43

4

IMPORTANT SAFETY CONSIDERATIONS

For ELD compliance, the device needs to be mounted in a xed position during
the operation of the commercial motor vehicle and visible to the driver when the
driver is seated in the normal driving position.

Ensure that the location does not interfere with the driver’s operation of the
commercial motor vehicle, including view of gauges, and does not protrude over
the dash covering the windshield view.

The mounting plate should be located on an area that is at and can support the
weight of the mount arm and the device.

5

INSTALLATION KITS

M-010-0659 - Trimble Duo Base Installation Kit

Part Number Item

M-010-0637 Trimble Duo Display

H-010-0529 RAM Mount

H-048-0523 8-32 x 5/8” Screw Pack

H-048-0526 #8 x3/4” Screw Pack

M-010-0647 - Trimble Duo Standard Installation Kit

Part Number Item

M-010-0637 Trimble Duo Display

H-010-0529 RAM Mount

H-048-0523 8-32 x 5/8” Screw Pack

H-048-0526 #8 x3/4” Screw Pack

L-016-0681 9-Pin Pass Through Connector

M-010-0648 - Trimble Duo 2-Pin Installation Kit

Part Number Item

M-010-0637 Trimble Duo Display

H-010-0529 RAM Mount

H-048-0523 8-32 x 5/8” Screw Pack

H-048-0526 #8 x3/4” Screw Pack

L-016-0652 J1939 2-Pin Cable

L-016-0153 J1939 Pigtail Kit

6

M-010-0649 - Trimble Duo OBD-II Installation Kit

Part Number Item

M-010-0637 Trimble Duo Display

H-010-0529 RAM Mount

H-048-0523 8-32 x 5/8” Screw Pack

H-048-0526 #8 x3/4” Screw Pack

L-016-0653 OBD-II Cable

M-010-0699 - Trimble Duo RP1226 Installation Kit

Part Number Item

M-010-0637 Trimble Duo Display

H-010-0529 RAM Mount

H-048-0523 8-32 x 5/8” Screw Pack

H-048-0526 #8 x3/4” Screw Pack

L-016-0698 PR1226 Cable

M-010-0650 - Trimble Duo Volvo / Mack Installation Kit

Part Number Item

M-010-0637 Trimble Duo Display

H-010-0529 RAM Mount

H-048-0523 8-32 x 5/8” Screw Pack

H-048-0526 #8 x3/4” Screw Pack

L-016-0654 Volvo / Mack Cable

Optional Mount Accessories

Part Number Item

H-050-0530 Suction Cup Mount

H-050-0526 Grab-Bar Claw Mount

7

TRIMBLE DUO DIAGRAM

FRONT BACK

Model: Trimble Duo
P/N : L019-0517
Input : 12V 1.5A
Contains FCC ID : NKS-DUO-LTE
Contains FCC ID : NKS-DUO-WIFI
Made in China

DSN: 12000000

S/N: DUO1829000000

Trade Name : TRIMBLE
Manufacturer : TRIMBLE
6807 Shady Oak Road Eden Prairie,
MN 55344, USA
Importer : TRIMBLE
6807 Shady Oak Road Eden Prairie,
MN 55344, USA

RoHS

RIGHT SIDE LEFT SIDE

8

TRIMBLE DUO SYSTEM OVERVIEW

DISPLAY CONNECTION

AUDIO (OPTIONAL)

VIDEO (OPTIONAL)

DIAGNOSTIC PORT
CONNECTOR

9

TRIMBLE DUO 9PIN PASS THROUGH CONNECTOR

The Duo 9-Pin Pass Through Connector Cable (part L-016-0681) is recommend for most vehicle installations. It connects
directly to the vehicle diagnostic port and allows an additional cable to be attached. This cable works with most Class 6-8
vehicles.

10

TRIMBLE DUO OBDII MAIN CABLE

The Duo OBD-II Main Cable (part L-016-0653) is
recommended for small vehicles running OBD-II engine
data. This will include most vans, pick-up trucks, and
sedans. The cable connects directly to the OBD-II port
near the steering column of the vehicle.

11

TRIMBLE DUO VOLVO / MACK CABLE

The Trimble Duo Volvo / Mack Cable (part L-016-0654) is
recommended for 2013 to 2017 Volvo and Mack trucks
with Volvo and Mack engines. The cable connects directly
to the diagnostic port of the vehicle.

12

TRIMBLE DUO PR1226 CABLE

The Trimble Duo PR1226 Cable (part L-016-0698) is designed to
work with the following vehicles:

2018 and newer Class 8 Kenworth and Peterbuilt trucks.

2020 and newer vehicles including Freightliner,
International, Mack, or Volvo that were built with the
RP1226. Consult your dealership for details.

13

TRIMBLE DUO 2PIN MAIN CABLE

The Duo 2-Pin Main Cable (part L-016-0652).

14

TRIMBLE DUO OPTIONAL ACCESSORIES

Optional accessories are available to mount the Trimble Duo without the use of drilling holes.

SUCTION CUP MOUNT

H0500530

GRABBAR CLAW MOUNT

H0500526

15