Page 1
Quick Installation Guide
TEG-160WS
TEG-240WS
Page 2
Table of Contents
Table of Contents
English ......................................................................................................
1. Before You Start
2. Hardware Installation ........................................................................
3. Web Management Utility ....................................................................
Troubleshooting ........................................................................................
................................................................................
1
1
2
3
6
Version 04.28.2006
Page 3
1. Before You Start
Package Content
TEG-160WS/TEG-240WS
Quick Installation Guide
Utility & User Guide CD-ROM
2 Mounting Brackets with Screws
Power Cord
System Requirements
Web Browser: Internet Explorer (5.0 or above), Netscape (6.0 or above)
Computer with Network adapter installed
Application
16-Port 10/100/1000Mbps Gigabit
Web Smart Switch
(TEG-160WS)
Or
24-Port 10/100/1000Mbps Gigabit
Web Smart Switch
(TEG-240WS)
Servers with 10/100/1000Mbps
Copper Gigabit PCI Adapter
(TEG-PCITXR)
Workstations with
10/100Mbps Ethernet Card
(TE100-PCIWN)
gigabit
1
English
Workstations with 10/100/1000Mbps
Copper Gigabit PCI Adapter
(TEG-PCITXR)
Page 4
2. Hardware Installation
Note: After hardware installation is complete, use the Web-based Smart Utility
to configure the TEG-160WS/TEG-240WS. To access the Web-based Smart
Utility, open your web browser, and enter the default IP Address
http://192.168.0.1
and the TEG-160WS/TEG-240WS are configured to the same network
segment.
1. Connect the Power Cord to the
rear of the TEG-160WS/
TEG-240WS and then to a power
outlet.
2. Connect a CAT-5 RJ-45 network
cable from the computer to an
available Ethernet port of the
TEG-160WS/TEG-240WS.
and default password "admin". Make sure your computer
2
English
Page 5
3. Web Management Utility
ote: If you would like to easily discover all the Web Management Switches on
the network, assign IP Address, change the password, and upgrade to new
firmware, then install the Web Management Utility. Follow the steps below.
For Windows User
1. Insert the Utility & User’s Guide
CD-ROM into your computer's
CD-ROM Drive and then click
Install Utility.
2. Follow the Installation Wizard
instructions. Click OK.
3. Click Start > Programs >
web_management_utility, and
then click
web_management_utility.
3
English
Page 6
4. Click Discovery, and then double-
click the Switch that appears in
the Discovery List.
5. Click the Switch in the Monitor
List and then click Configuration
setting.
6. Configure the IP Address, Subnet
mask, Gateway, and Password.
Click Set.
4
English
Page 7
7. Click OK.
8. Click Web access.
9. Type in your Password and then
click Login.
For more information regarding the Web-based Smart Utility configuration and
advanced settings, please refer to the User's Guide included on the Utility CDROM or TRENDnet's website at www.trendnet.com
5
English
Page 8
Troubleshooting
After connecting the TEG-160WS/TEG-240WS to a power outlet, the LEDs do not turn on.
Q1:
Q2:
discover the TEG-160WS/TEG-240WS. What should I do?
Q3:
me “only one user can login”. What should I do?
Q4:
Q5:
the 100Mbps LED remains off.
If you still encounter problems or have any questions regarding the TEG-160WS/TEG-240WS, please
refer to the User's Guide included on the Utility CD-ROM or contact TRENDnet's Technical Support
Department.
Check the connection of the power cord to the TEG-160WS/TEG-240WS and the power
A1:
outlet. Also check that the power outlet is receiving power.
After installing the Web-Management Utility, I clicked Discovery and the Utility is unable to
Make sure that the TEG-160WS/TEG-240WS is powered on and that all connections are
A2:
secure. Also check that your computer's IP Address is on the same network segment as the
TEG-160WS/TEG-240WS. The default IP Address of the Switch is 192.168.0.1 and the default
password is admin.
When I access the TEG-160WS/TEG-240WS using a web browser, I get a screen that tells
Another computer is configuring the TEG-160WS/TEG-240WS. Please wait until the user
A3:
logs off. If the other user has already logged off and you still get the same screen, then
disconnect the power cord from the TEG-160WS/TEG-240WS, wait for 5 seconds, reconnect
the power cord to theTEG-160WS/TEG-240WS, allow 5 seconds for the Switch to power on,
and then attempt to access the web configuration page to login.
I forgot the administration password. How do I reset my TEG-160WS/TEG-240WS?
Press on the reset button using a pen or paperclip for 10 seconds. The default password is
A4:
admin.
When I connect a computer to the Switch's gigabit port, the LINK/ACT LED turns on, but
When the 1000Mbps LED remains off, the computer's connection speed is 10Mbps or
A5:
100Mbps (if the 100Mbps LED is on). Make sure that you have a Gigabit Ethernet adapter
installed. Also make sure to use a CAT-5e or CAT- 6 Ethernet cable.
6
Page 9
Certifications
This equipment has been tested and found to comply with FCC and CE Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received. Including interference that may
cause undesired operation.
Waste electrical and electronic products must not
be disposed of with household waste. Please
recycle where facilities exist. Check with you Local
Authority or Retailer for recycling advice.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV
INTERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS
EQUIPMENT. SUCH MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO
OPERATE THE EQUIPMENT.
ADVERTENCIA
En todos nuestros equipos se mencionan claramente las caracteristicas del adaptador de
alimentacón necesario para su funcionamiento. El uso de un adaptador distinto al
mencionado puede producir daños fisicos y/o daños al equipo conectado. El adaptador
de alimentación debe operar con voltaje y frecuencia de la energia electrica domiciliaria
existente en el pais o zona de instalación.
Page 10
TRENDnet Technical Support
.
US Canada
Toll Free Telephone: 1(866) 845-3673
24/7 Tech Support
Europe (Germany France Italy Spain Switzerland UK)
Toll Free Telephone: +00800 60 76 76 67
English/Espanol - 24/7
Francais/Deutsch - 11am-8pm, Monday - Friday MET
. . . . .
Worldwide
Telephone: +(31) (0) 20 504 05 35
English/Espanol - 24/7
Francais/Deutsch - 11am-8pm, Monday - Friday MET
Product Warranty Registration
Please take a moment to register your product online.
Go to TRENDnet’s website at http://www.trendnet.com
20675 Manhattan Place
Torrance, CA 90501
USA
Copyright ©2006. All Rights Reserved. TRENDnet.
Loading...