Transition Networks CMEFG1014-100, CMEFG1013-110, CMEFG1029-100, CMEFG1014-110, CMEFG1029-101 User Manual
...
User’s Guide
CMEFG10xx-1xx - Slide-in-Module
SMEFG10xx-1xx - Stand-Alone
Media Converters
•
Copper to Fiber Gigabit Ethernet
• 10/100/1000Base-T to 1000Base-SX/LX
CMEFG10xx-1xx
(local)
Remote management
The CMEFG10xx-1xx (chassis version) is designed to remotely manage the
SMEFG10xx-1xx (the stand-alone version) or another CMEFG10xx-1xx per IEEE
802.3ah™:2004 standard.
For example, a local CMEFG1011-100 converter installed in a managed Transition
Networks PointSystem™ chassis is connected, via fiber, to a remote SMEFG1011100 converter.
Network management
The SNMP section lists commands for monitoring and managing a networked
media converter at a remote location. The CMEFG10xx-2xx and SMEFG10xx-2xx
devices are supported by 050xxxxx and later revisions of the management agent.
Please download the latest management firmware at www.transition.com.
Transition Networks CMEFG10xx-1xx and
SMEFG10xx-1xx series gigabit Ethernet media
converters connect 10/100/1000Base-T
shielded or unshielded twisted-pair copper
cable to 1000Base-SX/LX fiber-optic cable.
The media converters are designed to be
installed in pairs where the CMEFG10xx-1xx
is the local media converter and the
SMEFG10xx-1xx is the remote media
converter.
SMEFG10xx-1xx
(remote)
Installation . . . . . . . . . . . . . . . . . . . . . . . . . .5
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Diagnostic Management Interface (DMI) . . . .14
Cable Specification . . . . . . . . . . . . . . . . . . . .15
Technical Specifications . . . . . . . . . . . . . . . .18
Troubleshooting . . . . . . . . . . . . . . . . . . . . . .19
Contact Us . . . . . . . . . . . . . . . . . . . . . . . . . .22
Compliance . . . . . . . . . . . . . . . . . . . . . . . . .23
2
CMEFG10xx-1xx / SMEFG10xx-1xx
24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Part Number Port 1 - Copper
10/100/1000Base-T
Port 2 - Single Fiber-Optic
1000Base-BX-U/D, single mode
CMEFG1029-100
SMEFG1029-100
RJ-45
100m (328 ft)
SC, 1310 nm (TX) / 1490 nm (RX)
20 km (12.4 miles)
CMEFG1029-101
SMEFG1029-101
RJ-45,
100m (328 ft)
SC, 1490 nm (TX) / 1310 nm (RX)
20 km (12.4 miles)
CMEFG1029-102
SMEFG1029-102
RJ-45
100m (328 ft)
SC, 1310 nm (TX) / 1490 nm (RX)
40 km (24.9 miles)
CMEFG1029-103
SMEFG1029-103
RJ-45
100m (328 ft)
SC, 1490 nm (TX) / 1310 nm (RX)
40 km (24.9 miles)
TX = transmit, RX = receive
Note: The distances listed are the typical maximum cable distance. Actual
distance is dependent upon the physical characteristics of the network.
Install a CMEFG1029-100 (local) with a SMEFG1029-101 (remote).
Or install a CMEFG1029-101 (local) with a SMEFG1029-100 (remote).
Install a CMEFG1029-102 (local) with a SMEFG1029-103 (remote).
Or install a CMEFG1029-103 (local) with a SMEFG1029-102 (remote).
Part Number Port 1 - Copper
10/100/1000Base-T
Port 2 - Duplex Fiber-Optic
CMEFG1013-100
SMEFG1013-100
RJ-45
100m (328 ft)
SC, 1000Base-SX, 850 nm multimode
220 m (720 ft)
CMEFG1014-100
SMEFG1014-100
RJ-45
100m (328 ft)
SC, 1000Base-LX, 1310 nm Single Mode
10 km (6.2 miles)
CMEFG1015-100
SMEFG1015-100
RJ-45
100m (328 ft)
SC, 1000Base-LX, 1310 nm single mode
25 km (15.5 miles)
CMEFG1017-100
SMEFG1017-100
RJ-45
100m (328 ft)
SC, 1000Base-LX, 1550 nm single mode
65 km (40.4 miles)
CMEFG1035-100
SMEFG1035-100
RJ-45
100m (328 ft)
SC, 1000Base-LX, 1550 nm single mode
125 km (77.6 miles)
Standard Models (-10x)
The standard models (listed below) perform as described in the user’s guide with
one exception: These models do not include DMI functionality.
The standard models also include single mode, single fiber models (listed below.)
techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.
3
Part Number Port 1 - Copper
10/100/1000Base-T
CMEFG1029-110
SMEFG1029-110
RJ-45
100m (328 ft)
SC, 1310 nm (TX) / 1490 nm (RX)
20 km (12.4 miles)
CMEFG1029-111
SMEFG1029-111
RJ-45,
100m (328 ft)
SC, 1490 nm (TX) / 1310 nm (RX)
20 km (12.4 miles)
CMEFG1029-112
SMEFG1029-112
RJ-45
100m (328 ft)
SC, 1310 nm (TX) / 1490 nm (RX)
40 km (24.9 miles)
CMEFG1029-113
SMEFG1029-113
RJ-45
100m (328 ft)
SC, 1490 nm (TX) / 1310 nm (RX)
40 km (24.9 miles)
TX = transmit, RX = receive
Note: The distances listed are the typical maximum cable distance. Actual distance
is dependent upon the physical characteristics of the network.
Install a CMEFG1029-112 (local) with a SMEFG1029-113 (remote).
Or install a CMEFG1029-113 (local) with a SMEFG1029-112 (remote).
Part Number Port 1 - Copper
10/100/1000Base-T
Port 2 - Duplex Fiber-Optic
CMEFG1013-110
SMEFG1013-110
RJ-45
100m (328 ft)
SC, 1000Base-SX, 850 nm multimode
220 m (720 ft)
CMEFG1014-110
SMEFG1014-110
RJ-45
100m (328 ft)
SC, 1000Base-LX-10, 1310 nm singlemode
10 km (6.2 miles)
CMEFG1015-110
SMEFG1015-110
RJ-45
100m (328 ft)
SC, 1000Base-LX, 1310 nm single mode
25 km (15.5 miles)
The DMI models also include single mode, single fiber models listed below.
DMI Models (-11x)
The Diagnostic Monitoring Interface (DMI) models (listed below) allow diagnosing
problems within the network. These devices have four functions:
• Transmit power
• Receive power
• Transmit bias current
• Temperature
Within each function, the device will send a trap (i.e., error) whenever a high or
low warning event or a high or low alarm event occurs (for a total of 16 traps).
In addition, if both the local and remote media converters are DMI models, the
device will distinguish whether the trap event is from a local or a remote device.
Install a CMEFG1029-110 (local) with a SMEFG1029-111 (remote).
Or install a CMEFG1029-111 (local) with a SMEFG1029-110 (remote).
Port 2 - Single Fiber-Optic
1000Base-BX-U/D, single mode
4
CMEFG10xx-1xx / SMEFG10xx-1xx
24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Stand-Alone Media Converter
• Copper to Fiber
• 10/100/1000Base-TX to 1000Base-SX/LX
• Small Form Fact Pluggable (SFP) Fiber Port
Transition Networks SMEFG1040-1xx series
media converters connect 10Base-TX, 100BaseTX, or 1000Base-TX twisted-pair copper cable to
1000Base-SX or 1000Base-LX fiber cable.
The SMEFG1040-10x has one copper port and
one SFP port.
SMEFG1040-1xx
*Typical maximum cable distance. Actual distance is dependent upon the physical
characteristics of the network.
Note: Third-party Multi-Source Agreement (MSA) compliant Small Form Factor
Pluggables (SFPs) can also be used in the SFMFF1040-1xx device.
The following DMI supported SFP transceiver modules are compatible with the
SFMFF1040-1xx converter and are available from Transition Networks
(sold separately).
Part Number Duplex Fiber-Optic Port 2
TN-SFP-SX
LC, 1000Base-SX, 850 nm multimode, 220-550 mm (720-1804 ft)*
TN-SFP-LX1 LC, 1000Base-LX, 1310 nm single mode, 10 km (6.2 miles)*
TN-SFP-LX3 LC, 1000Base-LX, 1310 nm single mode, 30 km (18.8 miles)*
TN-SFP-LX5 LC, 1000Base-LX, 1550 nm single mode, 50 km (31.2 miles)*
TN-SFP-LX8 LC, 1000Base-LX, 1550 nm single mode, 80 km (50.0 miles)*
Copper Port 1: 10/100/1000-Base-TX
RJ-45 100 m (328 ft)
CMEFG1040-1xx
Slide-in-Module Media Converter
• Copper to Fiber
• 10/100/1000Base-TX to 1000Base-SX/LX
• Small Form Fact Pluggable (SFP) Fiber Port
Transition Networks CMEFG1040-1xx series media
converters, designed to be installed in a
PointSystem™ chassis connect 10Base-TX,
100Base-TX, or 1000Base-TX twisted-pair copper
cable to 1000Base-SX or 1000Base-LX fiber cable. It
has one copper port and one SFP port.
Part Numbers CMEFG1040-1xx and SMEFG1040-1xx
techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.
5
Installation
Install the CMEFG10xx-10x
CAUTION: Wear a grounding device and observe electrostatic discharge
precautions when installing the CMEFG10xx-1xx media converter in the
PointSystem™ chassis. Failure to observe this caution could result in damage
to, and subsequent failure of the CMEFG10xx-1xx media converter.
To install the CMEFG10xx-1xx media converter slide-in-module:
1. Locate an empty installation slot on the PointSystem™ chassis.
2. Carefully insert the slide-in-module into the slot, aligning the module
with the slot guides.
3. Ensure that the module is firmly seated against the back of the chassis.
4. Push in and rotate the panel-fastener screw
CFMFF100
CFMFF100
CETCF100
CFETF100
SPD
PWR
FRX
CRX
FLNK
CLNK
100BASE-TX
RX
TX
100BASE-FX
Link Alert
E
D
0
50½
LA
PWR
RXF
RXC
LNK
COL
10BASE-2
10BASE-FL
LKS
PWR
LKM
LKS
PWR
LKM
Multimode
Singlemode
TX
RX
TX
RX
Multimode
Singlemode
TX
RX
TX
RX
I
0
TERM
INIT
RX
TX
LNK
PWR
CPSMM120
SERIAL
10BASE-T
R
E
S
E
T
I
0
PWR
10/100/1000Base-T
RX
TX
1000Base-SX/LX
FD LACT
Panel Fastener Screw
Note: The CMEFG10xx.1xx is not designed for use in the Transition Networks
single-slot chassis. It will work in all other Transition Networks chassis.
6
CMEFG10xx-1xx / SMEFG10xx-1xx
24-hour Technical Support: 1-800-260-1312 International: 00-1-952-941-7600
Installation -- Continued
Install the fiber cable
1. Locate or build 1000Base-SX/LX compliant fiber cable with male, twostranded TX to RX connectors installed at both ends.
2. Connect the fiber cables to the CMEFG10xx-1xx media converter as
described:
• Connect the male TX cable connector to the female TX connector.
• Connect the male RX cable connector to the female RX connector.
3. Connect the fiber cables to the SMEFG10xx-1xx media converter as
described:
• Connect the male TX cable connector to the female RX connector.
• Connect the male RX cable connector to the female TX connector.
Connect the fiber cable to
the local CMEFG10xx-2xx
media converter as shown.
Connect the fiber cable to
the remote SMEFG10xx-2xx
media converter as shown
RX
TX
RX
TX
Install the copper cable
1. Locate or build 10, 100, or 1000Base-T compliant copper cables with
male, RJ-45 connectors installed at both ends.
2. Connect the RJ-45 connector at one end of the cable to the media
converter’s 10/100/1000Base-T RJ-45 port.
3. Connect the RJ-45 connector at the other end of the cable to the 10, 100,
or 1000Base-T RJ-45 port on the other device (switch, workstation, etc.).
Note: The AutoCross feature allows the use of either straight-through or
crossover configuration cables.
RJ-45 port
on the other device
(switch, work station, etc.)
RJ-45 port
on the media
converter
techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.
7
Operation
Status LEDs
The CMEFG10xx-1xx and SMEFG10xx-1xx series
media converters are designed to operate without user
intervention. Use the status LEDs to monitor the media
converter operation in the network.
Copper status LEDs
The status LEDs for the copper connection are integrated into the RJ-45 port.
These LEDs are not labeled on the media converter. Refer to the drawing to
the right for their locations.
Duplex/
Link Yellow A link in half-duplex mode has been established
for the copper connection.
Flashing Yellow The copper connection is transmitting/receiving
data in half-duplex mode.
Green A link in full-duplex mode has been established
for the copper connection.
Flashing Green The copper connection is transmitting/receiving
data in full-duplex mode.
Speed OFF 10 Mb/s operation.
Yellow 100 Mb/s operation.
Green 1000 Mb/s operation.
Installation -- Continued
Powering the CMEFG10xx-1xx converter
The CMEFG10xx-1xx slide-In-module is powered through the Transition
Networks PointSystem™ chassis.
Powering the SMEFG10xx-1xx converter
To power the SMEFG10xx-1xx media converter:
1. Connect the barrel connector on the power adapter cord to the media
converter’s power port (located on the back of the media converter).
2. Connect the power adapter plug to AC power.
3. Verify that the media converter has powered UP: the LED power
indicator light will be ON.
For DC power, consult the user’s guide for the Transition Networks DC
external power supply (P/N SPS1872-xx ) for powering the media converter.
Speed
10/100/1000Base-T
Duplex/Link
Loading...