Transition Networks CGFEB1xxx-15x, CGFEB1x40-170 User Manual
User’s Guide
CGFEB1xxx-15x Slide-in-Module Media
Converter
• Fiber to Fiber
• 100Base-FX to 1000Base-SX/LX
Transition Networks CGFEB1xxx-15x series media
converters are designed to install in a PointSystem™
chassis; they connect 100Base-FX to 1000Base-SX or
1000Base-LX devices.
The CGFEB1xxx-15x has two fiber-optic ports.
Installation . . . . . . . . . . . . . . . .4
Operation . . . . . . . . . . . . . . . . .8
Diagnostic Monitoring Interface .
(DMI) . . . . . . . . . . . . . . . . . . .11
Cable Specifications . . . . . . . .12
Technical Specifications . . . . .14
Troubleshooting . . . . . . . . . . .15
Contact Us . . . . . . . . . . . . . . .16
Declaration of Conformity . . .17
Compliance Information . . . . .18
CGFEB1xxx-15x
CGFEB1x40-170
Slide-in-Module Media Converter
• Fiber to Fiber
• 100Base-FX to Small Form Factor (SFP)
Transition Networks CGFEB1x40-1xx series media
converters are designed to install in a PointSystem
chassis; they connect 100Base-FX to 1000Base SFPs.
The CGFEB1x40-170 has one 100Base-FX port and one
1000Base SFP port.
CGFEB1x40-170
Note: Third party Multi Source Agreement (MSA) compliant Small Form Factor
Pluggables (SFPs) can be used in the CGFEB1xxx-15x and the CGFEB1x40-170
media converters.
2
CGFEB1xxx-1xx
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Part Number Port 2 - Single Fiber-Optic
1000Base-SX, single mode*
CGFEB1329-150
SC 100Base-FX 1300 nm
multimode 2km (1.2 miles)
SC, 1310nm TX/1550nm RX single
fiber, SM 20 km (12.4 miles)
CGFEB1329-151
SC 100Base-FX 1300 nm
multimode 2km (1.2 miles)
SC, 1550nm TX/1310nm RX single
fiber, SM 20 km (12.4 miles)
Install CGFEB1029-120 and CGFEB1029-121 in the same network
where one is the local converter and the other is the remote
converter.
CGFEB1329-152
SC 100Base-FX 1300 nm
multimode 2km (1.2 miles)
SC, 1310 nm TX/1550 nm RX single
fiber, SM 40 km (24.9 miles)
CGFEB1329-153
SC 100Base-FX 1300 nm
multimode 2km (1.2 miles)
SC, 1550nm TX/1310nm RX single
fiber, SM 40 km (24.9 miles)
Install CGFEB1029-122 and CGFEB1029-123 in the same network
where one is the local converter and the other is the remote
converter.
CGFEB1429-150
SC 100Base-FX 1300 nm
single mode 20km (12.4 miles)
SC, 1310nm TX/1550 nm RX single
fiber, SM 20 km (12.4 miles)
CGFEB1429-151
SC 100Base-FX 1300 nm
single mode 20km (12.4 miles)
SC, 1550nm TX/1310 nm RX single
fiber, SM 20 km (12.4 miles)
Install CGFEB1429-150 and CGFEB1429-151 in the same network
where one is the local converter and the other is the remote converter.
Part Number Port 2 - 1000Base-SX/LX*
CGFEB1313-150
SC 100Base-FX, 1300 nm
multimode 2km (1.2 miles)
SC, 1000Base-SX, 850 nm, MM
62.5/125μm: 220 m (722 ft)
50/125μm: 550 m (1804 ft)
CGFEB1314-150
SC 100Base-FX 1300 nm
multimode 2km (1.2 miles)
SC, 1000Base-LX, 1310 nm single
mode, 10 km (6.2 miles)
CGFEB1315-150
SC 100Base-FX 1300 nm
multimode 2km (1.2 miles)
SC, 1000Base-LX, 1310 nm single
mode, 25 km (15.5 miles)
CGFEB1317-150
SC 100Base-FX 1300 nm
multimode 2km (1.2 miles)
SC, 1000Base-LX, 1550 nm
single mode, 65 km (40.4 miles)
CGFEB1324-150
SC 100Base-FX 1300 nm
multimode 2km (1.2 miles)
SC, 1000BASE-LX 1310nm MM
Extended (62.5/125 μm fiber only)
up to 2 km (1.2 miles)
CGFEB1335-150
SC 100Base-FX 1300 nm
multimode 2km (1.2 miles)
SC, 1000Base-LX, 1550 nm single
mode 125 km (77.7 miles)
Port 1 -100Base-FX*
The CGFEB1324 extends 1000Base-LX beyond 220 meters. Transition Networks cannot
guarantee a full 2-km distance on every installation since the distance is largely
dependent on the quality of the fiber, cable installation, and splicing.
Port 1 -100Base-FX*
*Typical maximum cable distance. Actual distance is dependent upon the physical
characteristics of the network.
CGFEB1xxx-1xx
techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.
3
Part Number Port 2 - 1000Base-X SFP Slot Port 1 - 100Base-FX*
CGFEB1340-170
EmptySC, 100Base-FX, 1300 nm
multimode, 2 km (1.2 miles)
CGFEB1440-170
EmptySC, 100Base-FX, 1300 nm
single mode 20 km (12.4miles)
*Typical maximum cable distance. Actual distance is dependent upon the physical
characteristics of the network.
Note: Third party Multi Source Agreement (MSA) compliant Small Form Factor
Pluggables (SFPs) can be used in the CGFEB1x40-170 media converters.
CGFEB1429-152
SC 100Base-FX 1310 nm
single mode 20km (12.4 miles)
SC, 1310 nm TX/1550 nm RX single
fiber, SM 40 km (24.9 miles)
CGFEB1429-153
SC 100Base-FX 1310 nm
single mode 20km (12.4 miles)
SC, 1550nm TX/1310nm RX single
fiber, SM 40 km (24.9 miles)
Install CGFEB1429-152 and CGFEB1429-153 in the same network
where one is the local converter and the other is the remote
converter.
Part Number Port 2 - 1000Base-SX/LX*Port 1 -100Base-FX*
4
CGFEB1xxx-1xx
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Installation
CAUTION: Wear a grounding device and observe electrostatic discharge precautions
when handling the media converter. Failure to observe this caution could result in
damage the media converter.
Four-position switch
The four-position switch is located on the circuit board of the media converter. Use a
small, flat-blade screwdriver (or a similar device) to set the switch according to the site
requirements (see the drawing below).
100Base-FX Duplex: UP = Full, Down = Half
LPT: UP = Enabled, Down = Disabled
Unused
SW Position Up
SW Position Down
Unused
1234
1. 100Base-FX Full/Half Duplex
UP Operates in full-duplex mode
DOWN Operates in half-duplex mode
2. Link Pass-Through (LPT)
UP Enable Link Pass-Through
DOWN Disable Link Pass-Through
3. Not used
4. Not used
CGFEB1xxx-1xx
techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.
5
Install the chassis card
1. Remove one chassis slot cover from the Point System Chassis (keep the slot
cover and screw).
2. Carefully slide the media converter into the chassis slot, aligning it with slot
guides.
3. Ensure that the media converter is firmly seated in the slot.
4. Push in and rotate the panel fastener to secure the module to the chassis. See
illustration below.
Point System Chassis
Media Converter
Panel Fastener
Slot
Hardware/software jumper
The hardware/software three-pin header J5 is located on the circuit board labeled H
and S. See jumper positions below.
Note: Use small needle-nose pliers to set the jumper.
Hardware The media converter mode is determined by the 4-
position switch settings.
Software The media converter mode is determined by the
most-recently saved, on-board microprocessor
settings.
S
J5
S
J5
Installation -- Continued
6
CGFEB1xxx-1xx
24-Hour Technical Support: 1-800-260-1312 -- International: 00-1-952-941-7600
Port locations
The drawings below illustrate the locations of Port 1 and Port 2
The CGFEB1xxx-150 and -170 media converters have two ports.
Port 1
Port 2
CGFEB170
LK1
TX
RX
PWR
LK2
FD
TX
RX
TX
RX
PWR
FD
CGFEB150
LK2
LK1
Port 2
Port 1
150s
Port 1: 100Base-FX
Port 2: 1000Base-SX or 1000Base-LX
170s
Port 1: 100Base-FX
Port 2: 1000Base-X SFP Slot
Installation -- Continued
techsupport@transition.com -- Click the “Transition Now” link for a live Web chat.
7
CGFEB1xxx-1xx
Installation -- continued
Installing fiber cables
1. Locate either a 100Base-FX or 1000Base-SX/LX compliant fiber cable with
male, two-stranded TX to RX connectors installed at both ends.
2. Connect the fiber cables to the fiber port on the media converter (port 2) as
described:
• Connect the male TX cable connector to the female TX connector.
• Connect the male RX cable connector to the female RX connector.
3. Connect the fiber cables to the fiber port on the other device (another media
converter, hub, etc.) as described:
• Connect the male TX cable connector to the female RX connector.
• Connect the male RX cable connector to the female TX connector.
Connect fiber cable
to media converter
as shown.
Connect fiber cable
to other device
(media converter,
hub, etc.) as shown
RX
TX
RX
TX
Loading...