Assembly Instructions BBQ400.04
DOC136 REV B
PARTS LIST
PART PREVIEW |
DESCRIPTION |
QTY |
PART# |
ID# |
|
1/4-20 SHOULDER BOLT LONG |
4 |
HDW154 |
A |
|
|
|
|
|
|
WASHER 1/2OD X 1/4 ID FLAT ZINC |
38 |
HDW249 |
B |
|
|
|
|
|
|
TOP SECTION |
1 |
|
C |
|
|
|
|
|
|
1/4-20 x .625 PHILLIPS PAN HEAD |
16 |
HDW066 |
D |
|
Zinc |
|
|
|
|
|
|
|
|
|
1/4 Lock Washer Zinc |
16 |
HDW113 |
E |
|
|
|
|
|
|
1/4-20 x .500 Truss Head Screw Zinc |
16 |
HDW095 |
F |
|
|
|
|
|
|
8-32 x .500 PPHD Zinc |
4 |
HDW245 |
G |
|
|
|
|
|
|
Door Handle Gasket |
2 |
INS147 |
H |
|
|
|
|
|
|
Base Pan Assembly |
1 |
SUB264 |
I |
|
|
|
|
|
|
Right Panel Assembly |
1 |
SUB267 |
J |
|
|
|
|
|
|
Left Panel Assembly |
1 |
SUB265 |
K |
|
|
|
|
|
|
Swivel Caster |
2 |
HDW051 |
L |
|
|
|
|
|
|
Fixed Caster |
2 |
HDW052 |
M |
|
|
|
|
|
|
Hopper Burner Assembly |
1 |
SUB268 |
N |
|
|
|
|
|
|
|
|
|
|
|
1/4-20 SHOULDER BOLT SHORT |
2 |
HDW155 |
O |
|
|
|
|
|
|
Left Shelf Assembly |
1 |
SUB277 |
P |
|
|
|
|
|
|
Right Shelf Assembly |
1 |
SUB278 |
Q |
|
|
|
|
|
|
Handle |
3 |
HDW227 |
R |
|
|
|
|
|
|
Door Right |
1 |
SUB273 |
S |
|
Door Left |
1 |
SUB280 |
|
|
|
|
|
|
|
2 |
|
|
|
|
Upper Hinge Assembly |
2 |
SUB309 |
T |
|
|
|
|
|
|
Front Panel Assembly |
1 |
SUB260 |
u |
|
|
|
BCA253 |
|
|
|
|
|
|
|
Grease Drain Assembly |
1 |
SUB254 |
V |
|
|
|
|
|
|
Heat Baffle |
1 |
BCA289 |
W |
|
|
|
|
|
|
Drip Pan |
1 |
BCA288 |
X |
|
|
|
|
|
|
Porcelain Grills |
2 |
HDW093 |
Y |
|
|
1 |
HDW094 |
|
|
|
|
|
|
|
Washer 3/4 OD X 5/16 ID Zinc |
8 |
HDW250 |
Z |
|
|
|
|
|
|
Lower Back Panel Assembly |
1 |
SUB266 |
AA |
|
|
|
|
|
|
#8 X .375 Phillips Pan Head Zinc |
8 |
HDW244 |
BB |
|
|
|
|
|
|
1/4-20 X .500 Truss Head SST |
8 |
HDW095 |
CC |
|
|
|
|
|
|
8-32 X .375 PPHD SST |
4 |
HDW097 |
DD |
|
|
|
|
|
|
1/4-20 X .375 Phillips Pan Head Zinc |
6 |
HDW251 |
EE |
|
|
|
|
|
|
1/4-20 X 1.5 HEX HEAD BOLT |
4 |
HDW156 |
FF |
|
|
|
|
|
|
8-32 X .187 PPHD SST |
2 |
HDW053 |
GG |
|
|
|
|
|
|
#8 Lock Washer |
2 |
HDW074 |
HH |
|
|
|
|
|
|
#8 Flat Washer |
2 |
HDW032 |
II |
|
|
|
|
|
|
Hopper Lid Handle |
1 |
FAB055 |
JJ |
|
|
|
|
|
|
Wire tie |
1 |
HDW128 |
KK |
|
|
|
|
|
Before assembly begins verify that you have all the correct parts from the above list of parts. The hardware kit shown on page 3 includes all the screws, nuts, bolts, and gaskets required for assembly. The back of the package identifies the ID# of the hardware as used in the instructions.
Tools needed for the assembly of the BBQ are:
A Phillips head screw driver, Flat head screw driver, and a 7/16 socket or nut driver or wrench. Two people will be required to assemble the BBQ.
3
HARDWARE KIT BACK
HARDWARE KIT FRONT 4
Loading...