Traeger Bbq075 Owner's Manual

OWNER’S MANUAL

BBQ075

RESIDENTIAL PELLET GRILL

This Grill Protected Under Patent Number: 4,823,684

FOR OUTDOOR USE ONLY!

WARNING!

DO NOT STORE OR USE COMBUSTABLE MATERIALS

NEAR THIS APPLIANCE!

USE ONLY TRAEGER BRAND HARDWOOD

BBQ PELLETS IN THE OPERATION OF THIS UNIT.

INTRODUCTION

Congratulations on your purchase of this Traeger Wood Pellet Grill, Model BBQ075.
With proper set-up, operation and maintenance, the Grill will provide you with delicious food
and years of cooking enjoyment.

NOTE: NUMBERS FOLLOWING PART NAMES REFER TO THE COMPONENT
DIAGRAM FOUND NEAR THE END OF THIS MANUAL.

When you un-box the Grill, remove all parts from the box and inside the Grill. Remove
any remaining packaging material from inside the Grill as well. Make sure you have, and
can identify all of the following parts:

Qty

Item Description Component Diagram Reference Number

(1) Grill ---------------------------------------------------------- 2
(1) Hopper / Burner Assembly ---------------------------- 31
(2) Caster Legs ----------------------------------------------- 119
(2) Wheel Legs ----------------------------------------------- 124
(1) Porcelain Grill -------------------------------------------- 166
(1) Grease Drain Pan --------------------------------------- 161
(1) Heat Baffle ------------------------------------------------ 157
(1) Smoke Stack --------------------------------------------- 133
(1) Chimney Cap Assembly ------------------------------- 135
(1) Chrome Door Handle ----------------------------------- 164
(1) Grease Bucket ------------------------------------------- 132
(1) Hardware Kit ---------------------------------------------- 144

You will need to complete the assembly which includes:

1) Mounting the Caster Legs (119) and Wheel Legs (124) to the Grill.

2) Attaching the Chrome Door Handle (164) to the Door (99).

3) Attaching the Smoke Stack (133) to the Grill.

4) Mounting the Chimney Cap Assembly (135).

5) Positioning the Heat Baffle (157) over the Firepot (70).

6) Positioning the Grease Drain Pan (161) over the Heat Baffle (157).

7) Positioning the Porcelain Grill (166) on the Grill Supports.

8) Hanging the Grease Bucket (132).

TOOLS ARE SUPPLIED FOR ASSEMBLY

(2) Open end wrenches
(1) Hex key (Allen Wrench)

Follow these step-by-step instructions and you’ll be cookin’ in no time!

SECTION ONE: ASSEMBLY INSTRUCTIONS

MOUNTING THE LEGS:

1) Carefully lay the Grill on its back on a non-abrasive surface. Note: The Hopper /
Burner Assembly (31) will be mounted to the Grill, but is not shown in the diagram
below for clarity.

2) Use the Black Bolts, Washers and Nuts (see Detail “A”) supplied in the Hardware Kit

(144) to install the Caster Legs (119) on the left end of the Grill and the Wheel Legs
(124) on the right end as shown in the diagram below. The Acorn Nuts (130) on the
Wheel Legs (124) should go toward the center of the Grill. Leave the Nuts loose
during this step.

3) Set the Grill upright to level and then tighten all Nuts.

ATTACHING THE CHROME DOOR HANDLE:

1) Insert the threaded studs on the Chrome Door Handle (164) through the slots in the
Door (99).

2) Place a Zinc Flat Washer, then a Zinc Lock Washer on each threaded stud. Secure
with Hex Nuts using the Wrench supplied. Do not over tighten.

ATTACHING THE SMOKE STACK AND CHIMNEY CAP ASSEMBLY:

1) Align the holes in the Smoke Stack (133) with the holes in the Smoke Stack Gasket
(142), which fits between the right end of the Grill and the Smoke Stack (133).

2) Place Zinc Flat Washers on two of the 1/2” long Hex Head Bolts and insert the Bolts
through the holes in the Smoke Stack (133) and the Smoke Stack Gasket (142).

3) Align the Bolts with the corresponding holes in the Grill. Place a Zinc Flat Washer on
each Bolt inside the Grill and secure with Zinc Hex Nuts using the Wrench supplied.

4) Screw the Chimney Cap Assembly (135) into the Bracket in the top of the Smoke
Stack. Hand tighten.

NOTE: If at this point you are ready to start your Grill, refer to the INITIAL FIRING
INSTRUCTIONS in SECTION TWO of this manual or on a separate sheet in the
PELLET HOPPER before proceeding with further assembly.

POSITIONING THE HEAT BAFFLE:

Position The Heat Baffle (157) directly over the Firepot (70) on the locating brackets
found on the inside walls of the Grill. The notched legs of the Heat Baffle (157) should
be facing downward to fit onto the locating brackets.

POSITIONING THE GREASE DRAIN PAN:

RECOMMENDATION for ease of clean-up: Line the Grease Drain Pan (161) with
heavy-duty aluminum foil. Be sure the edges and ends of the foil are tight against
the bottom of the Grease Drain Pan (161).

Position the Grease Drain Pan (161) so that the Short Lip end hooks over the Grease
Drain Pan Support on the left side of the Grill. The Long Lip end should rest in the
V-Shaped Grease Drain (23) located inside the Grill on the right.

POSITIONING THE PORCELAIN GRILL:

Position the Porcelain Grill (166) on the Grill Supports that run the length of the
cooking area.

HANGING THE GREASE BUCKET:

Locate the Grease Drain Tube, extending from the Grill below the Smoke Stack (133)
on the right end. Hang the Grease Bucket (132) on the Bucket Hook.