Traeger Bbq055 Owner's Manual

ltNbo’S MANrAi

BBnMRR

obSIabNTIAi mbiibT doIii

This drill mrotected rnder matent NumberW QIUOPISUQ

clo lrTallo rSb lNiY!

tAoNINd!

al NlT STlob lo rSb ClMBrSTABib MATboIAiS

NbAo TeIS AmmiIANCb!

rSb lNiY ToAbdbo BoANa eAoatlla

BBn mbiibTS IN Teb lmboATIlN lc TeIS rNIT.

fkTolarCTflk

`ongratulations on your purchas e of th is qraeger tood mellet drillI jode l BBnMRRK
tith proper setJupI operation and maintenanceI the drill will provide you with delicious
food and years of cooking enjoymentK

klTbW krMBbop cliiltfkd mAoT kAMbp TeolrdelrT Tefp MAkrAi
obcbo Tl Teb ClMmlkbkT afAdoAMK

then you unJbox the drillI make sure you haveI and can identify all of the following
partsW

ENF Bag of kutsI tashersI and BoltsK qhese are for mounting the mellet
eopperLBu rner EPTFI iegs ENNRI NNVI NOPI NOTFI theels ENPSF and eandles
ENPTF to the drill EPFK
ENF jain Body EPF
EQF iegs ENNRI NNVI NOPI NOTF and Axle ood ENPNF
ENF mellet eopperLBurner EPTF
ENF morcelain drill ENTMF oemove for assembly
ENF eeat Baffle ENRRFK oemove from grill for assembly
ENF drease arain man ENSPFK oemove from grill for assembly
ENF drease Bucket ENPRF
ENF aome qhermometer EPNF
EOF theels ENPSF

vou will need to complete the assembly which includesW
1F jounting the iegs ENNRI NNVI NOPI NOTF onto the drill Body EPF

OF jounting the Axle ood ENPNF and theels ENPSF to the theel iegs ENOPI NOTF
PF jounting the mellet eopper EPTF onto the drill Body EPF
QF jounting eandles ENPTF to aoor EORF and to right end of drill EPFK ao not over

tightenK aamage to the handles could resultK

RF mositioning the eeat Baffle ENRRF over the cirepot ESRFI and setting the drease arain

man ENSPF in placeK

SF eanging the drease Bucket ENPRF on the Bucket eook located below the drease

arain qube opening on the right side of the drill EPFK

collow these step by step instructions and you’ll be cook in’ in no time!

Tllip prmmifba clo AppbMBiv

PLU” L NLO” combo wrench
TLNS” L NLO” combo wrench
mhillips screwdriver

pbCTflk lkbW AppbMBiv fkpTorCTflkp

MlrkTfkd ibdp Aka tebbipW

mefiifmp p`obtp
tfqe ciAq tApebop
Aka ebu krqp fkpfab
EP mbo ibdF

ibd tfqe elibp clo
AuibLtebbip

ciAq tApebo Bbqtbbk
tebbi Aka ibd Aka
Bbqtbbk tebbi Aka
kvil`h krq OUTSIDE

ibd tfqe
Blqqlj `Am

Auib ola

klTbW fnstall all ieg pcrews and kutsI P in each iegI ibAsfkd krqp illpbK pet
drill upright to level and then tighten all nutsK

MlrkTfkd mbiibT elmmboLBrokboW

klTbW al klq remove the whiteI square Burner dasket EUSF from the eopperLBurner

EPTFK
1F plide the eopperLBurner EPTF square tube into the square opening located on th e left

side of the drill Body EPFK dently push the eopperLBurner EPTF into the drill Body EPF

until the eopperLBurner EPTF is s nug against the end of the drill Body EPFK
OF Align the bolt holes in the drill Body EPF with the kut perts in the eopperLBurner EPTFK
PF fnstall a clat tasher on each of the four eex eead BoltsK crom the ins ide of the drill

Body EPF install these Bolts with tashers into the eopperLBurner EPTF kut pertsK

qighten all four Bolts – al klT lsbo TfdeTbk Teb BliTpK