TL-PA4010
Table of contents
Loading...
TL-PA4010
AV500 Nano Powerline Adapter
Rev: 1.0.0
1910010724
COPYRIGHT & TRADEMARKS
Specifications are subject to change without notice. is a registered trademark of
TP-LINK TECHNOLOGIES CO., LTD. Other brands and product names are trademarks or registered
trademarks of their respective holders.
No part of the specifications may be reproduced in any form or by any means or used to make any
derivative such as translation, transformation, or adaptation without permission from TP-LINK
TECHNOLOGIES CO., LTD. Copyright © 2012 TP-LINK TECHNOLOGIES CO., LTD. All rights
reserved.
http://www.tp-link.com
I
FCC STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
Consult the dealer or an experienced radio/ TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
1) This device may not cause harmful interference.
2) This device must accept any interference received, including interference that may cause
undesired operation.
Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate the equipment.
CE Mark Warning
This is a class B product. In a domestic environment, this product may cause radio interference, in which
case the user may be required to take adequate measures.
Продукт сертифіковано згідно с правилами системи УкрСЕПРО на відповідність вимогам
нормативних документів та вимогам, що передбачені чинними законодавчими актами України.
Safety Information
When product has power button, the power button is one of the way to shut off the product; when
there is no power button, the only way to completely shut off power is to disconnect the product or
the power adapter from the power source.
Don’t disassemble the product, or make repairs yourself. You run the risk of electric shock and
voiding the limited warranty. If you need service, please contact us.
Avoid water and wet locations.
II
This product can be used in the following countries:
AT BG BY CA CZ DE DK EE
ES FI FR GB GR HU IE IT
LT LV MT NL NO PL PT RO
RU SE SK TR UA
III
TP-LINK TECHNOLOGIES CO., LTD
DECLARATION OF CONFORMITY
For the following equipment:
Product Description: AV500 Nano Powerline Adapter
Model No.: TL-PA4010
Trademark: TP-LINK
We declare under our own responsibility that the above products satisfy all the technical regulations
applicable to the product within the scope of Council Directives:
Directives 2004 / 108 / EC, Directives 2006 / 95 / EC, Directives 2011/65/EU
The above product is in conformity with the following standards or other normative documents：
EN 55022:2010
EN 55024:2010
EN 61000-3-2:2006+A1:2009+A2:2009
EN 61000-3-3:2008
EN 50412-2-1:2005
EN 60950-1:2006+A11:2009+A1:2010+A12:2011
The product carries the CE Mark
Person responsible for marking this declaration:
Yang Hongliang
Product Manager of International Business
Date of issue: 2012
TP-LINK TECHNOLOGIES CO., LTD.
Building 24 (floors 1, 3, 4, 5), and 28 (floors 1-4) Central Science and Technology Park, Shennan
Rd, Nanshan, Shenzhen, China
CONTENTS
Package Contents......................................................................................... 1
Chapter 1 Introduction ................................................................................. 2
1.1 Conventions ........................................................................................... 2
1.2 System Requirement.............................................................................. 2
1.3 Important Safety Instructions ................................................................. 2
Chapter 2 Connecting Mechanism .............................................................. 4
2.1 Introduction ............................................................................................ 4
2.2 LED Indicator ......................................................................................... 4
2.3 Physical Interface................................................................................... 5
2.4 Connection Instruction ........................................................................... 6
2.5 Hardware Connection – Computer......................................................... 6
2.6 Hardware Connection – Internet ............................................................ 7
Chapter 3 Installing Management Utility..................................................... 9
Chapter 4 Using the Management Utility.................................................. 13
4.1 Status ................................................................................................... 13
4.1.1 Set Local Device’s Network Name ................................................. 14
4.2 Network................................................................................................ 15
4.2.1 Rename the Remote Device/Enter Password ................................ 16
4.2.2 Add Device ..................................................................................... 16
4.3 Advanced ............................................................................................. 17
4.4 System ................................................................................................. 18
4.4.1 Upgrade Firmware.......................................................................... 19
4.4.2 Reset Device .................................................................................. 20
4.4.3 Set All Devices’ Network Name ...................................................... 20
Chapter 5 Advanced Feature: How to Use the Pair Buttons................... 21
5.1 Pair ( Secure with 128 bits-AES).......................................................... 21
5.2 Set Up a Powerline AV Network with the Pair Button........................... 21
Appendix A: Troubleshooting.................................................................... 23
V
TL-PA4010 AV500 Nano Powerline Adapter
Package Contents
The AV500 Nano Powerline Adapter package contains the following items:
One AV500 Nano Powerline Adapter (There are two AV500 Nano Powerline Adapters in Starter Kit)
One RJ-45 Ethernet Cable (There are two RJ-45 Ethernet Cables in Starter Kit)
One Resource CD
This Guide
Management Utility
Note:
Make sure that the package contains the above items. If any of the above items are damaged or missing,
please contact your dealer immediately.
1
TL-PA4010 AV500 Nano Powerline Adapter
Chapter 1 Introduction
Congratulations on your purchase of this outstanding Powerline Adapter. This device is an AV500 Nano
Powerline Adapter which transforms your house’s existing electrical wiring into a ubiquitous networking
infrastructure. Simply plug this AV500 Nano Powerline Adapter into an ordinary AC power outlet which
will easily extend your Cable/xDSL broadband connection or existing Ethernet (LAN) network to any
other electrical outlet in any room of a house without the need of any new cabling.
This Powerline Adapter supports up to 500Mbps data rate over the existing household power circuit.
With data rates of 500Mbps, full multimedia application can easily be supported throughout the whole
house in addition to Internet access. This Powerline Adapter uses the existing power lines installed in a
home as a path to transmit digital data, voice, audio and video between devices.
To ensure data communication’s security and multimedia applications, this Powerline Adapter support
built-in 128-bit AES encryption and Quality of Service (QoS) features.With minimum setup, you can
install and use this Powerline Adapter within minutes. The adapter adds two useful functions.
1． Existing connection with a new unassociated device added via the Pair button.
2． Reset to default setting via the Management Utility.
1.1 Conventions
The powerline adapter or AV500 Nano Powerline Adapter mentioned in this guide stands for TL-PA4010
AV500 Nano Powerline Adapter without any explanation.
1.2 System Requirement
a) At least two AC 100V~ 240V power outlets with standard home power wiring
b) A computer with the following:
Operating System with TCP/IP installed
Pentium III compatible processor and above
Ethernet LAN card installed with TCP/IP protocol
64 MB RAM or more
50 MB of free disk space (Minimum)
CD-ROM Drive
1.3 Important Safety Instructions
1. Do not open this product or attempt to service it; it may expose you to dangerous high voltage or
other risks.
2. Do not operate this product near water.
3. Do not place or operate this product near a radiator or a heat register.
4. Do not expose this product to dampness, dust or corrosive liquids.
5. Do not connect this product or disconnect it from a wall socket during a lightning or a thunderstorm
6. Do not block the ventilation slots of this product, for insufficient airflow may harm it.
7. Do not put anything on this product.
2
TL-PA4010 AV500 Nano Powerline Adapter
8. Plug this product directly into a wall socket (100Vac~240Vac). Do not use an extension cord
between this product and the AC power source.
9. When plugging this product into a wall socket, make sure that the electrical socket is not damaged,
and that there is no gas leakage.
10. Place the connecting cables properly so that people won’t stumble or walk on it.
11. This product should be operated from the type of power indicated on the marking label. If you are not
sure of the type of power available, consult the qualified technician.
12. Unplug this product from the mains and refer the product to qualified service personnel for the
following conditions:
If liquid has been spilled on the product
If the product has been exposed to rain or water
13. Unplug this product from the wall socket before cleaning. Use a damp cloth for cleaning. Do not use
liquid cleaners or aerosol cleaners.
14. The specification of the fuse is T4AL250V. To avoid damage, please do not change the fuse.
15. The Operating temperature is 0 ~4℃ 0 (32~10℃℉4)℉ .
16. The Storage temperature is -40 ~70℃℃ (-40 ~158 )℉℉.
3
Loading...