TP-Link M7000 quick start Guide
1. Install the SIM Card and Battery
Quick Installation Guide
Mobile Wi-Fi
* Images are for demonstration only.
LED Indicators
LED
(Wi-Fi)
(Internet)
(Battery)
!
©2020 TP-Link 7106508955 REV3.0.0
Status Explanation
On/O
On/O
Solid Green
Blinking Red
Blinking Green
O
The LEDs will turn o automatically after idling for 30 seconds. To check the LED
status, press the Power button to turn them on again.
Wi-Fi is enabled or disabled.
Internet service is available or unavailable.
Mobile Wi-Fi has enough power or is fully charged.
The battery level is lower than 10%.
Mobile Wi-Fi is charging.
Power is o.
a. Remove the back cover.
b. Install your SIM card.
c. Install the provided battery.
d. Note down the default SSID and Wireless
Password. Then replace the cover.
!
SIM card requirement:
Standard
SIM card
Provided Micro SIM card adapter + Provided sticker
SSID: TP-Link_XXXX
Wireless Password: XXXXXXXX
+ +
Micro SIM card +
Provided Nano SIM card adapter + Provided sticker
2
SSID: TP-Link_XXXX
Wireless Password: XXXXXXXX
1
+ +
Nano SIM card +
2. Connect to the Internet
a. Press and hold the Power button
to power on the Mobile Wi-Fi.
!
· If you cannot access the internet, refer to FAQ > Q1.
By default, Power Saving is enabled and the Mobile Wi-Fi will turn o Wi-Fi when no wireless devices are connected to it for 10 minutes.
·
To resume the Wi-Fi connection, press the Power button.
b. Connect your wireless device to the Mobile Wi-Fi using the
SSID and the Wireless Password you have noted down.
< Settings
Wi-Fi
SSID:
TP-Link_XXXX
Wi-Fi
CHOOSE A NETWORK...
TP-Link_XXXX
Other...
Wireless Password:
XXXXXXXX
SSID: TP-Link_XXXX
Wireless Password: XXXXXXXX
SSID:
TP-Link_XXXX
Wireless Password:
XXXXXXXX
SSID:
TP-Link_XXXX
Wireless Password:
XXXXXXXX
Enjoy the internet!
Managing Your Mobile Wi-Fi
Charging Your Mobile Wi-Fi
Manage your Mobile Wi-Fi using any of the methods below. You can customize Wi-Fi settings, block Wi-Fi devices and more.
tpMiFi App
1. Get the tpMiFi app from App Store or Google Play, or by
scanning the QR code.
Web Management Page
1. Connect your wireless device to the Mobile Wi-Fi. If it is a computer,
make sure it is set to obtain an IP address automatically.
2. Launch a web browser and visit http://tplinkmi.net or
http://192.168.0.1. Enter admin to log in.
2. Connect your wireless device to the Mobile Wi-Fi.
3. Launch tpMiFi and enter admin to log in.
For technical support, user manuals and more information,
please visit https://www.tp-link.com/support, or simply
scan the QR code.
FAQ (Frequently Asked Questions)
Q1. What should I do if I cannot access the internet (the Internet
LED doesn’t light up)?
A. Visit the web management page (http://tplinkmi.net) on your phone,
enter admin to log in, then check the following:
·
Check PIN status
If the current SIM card status is PIN Locked, your SIM card is PIN
protected and you need to unlock it using the PIN code provided by your
mobile carrier.
Verify the mobile carrier parameters
·
1. Go to Dial-up, tap View prole details, and verify that the parameters
(i.e. APN, username and password) provided by your mobile carrier are
correct.
2. If the parameters are not correct, return to the Dial-up page and
create a new prole with the correct information.
· Check the Data Roaming settings
If your SIM card is operated in a roaming service area, go to Dial-up, enable
Data Roaming and tap Done.
Check Mobile Data
·
Go to Dial-up to verify that Mobile Data is On. If not, enable it and tap Done.
·
Check Data Limit
Go to Device > Data Usage Settings to check whether your data usage has
exceeded the Total/Monthly allowance.
Q2. How do I restore the Mobile Wi-Fi to its factory default settings?
A. With the Mobile Wi-Fi powered on, remove the cover, then use a pin to
press and hold the Reset button until all LEDs turn on momentarily.
Note: Restoring the device to its factory defaults will clear all your settings.
Method 1
Via a Wall Outlet (Recommended)
5V/1A
!
· The Battery LED will be solid green when the Mobile Wi-Fi is fully charged.
The power adapter is not provided by TP-Link.
·
Method 2
Via a Computer
Safety Information
· Keep the device away from water, re, humidity or hot environments.
· Do not attempt to disassemble, repair, or modify the device. If you need service,
please contact us.
· Do not use the device where wireless devices are not allowed.
· Do not disassemble, crush, puncture, short external contacts, or dispose of the
battery in re or water.
· Do not leave a battery in an extremely high temperature surrounding
environment that can result in an explosion or the leakage of ammable liquid or
gas. Do not leave a battery subjected to extremely low air pressure that may
result in an explosion or the leakage of ammable liquid or gas.
CAUTION: RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT
TYPE.
Please read and follow the above safety information when operating the device.
We cannot guarantee that no accidents or damage will occur due to improper
use of the device. Please use this product with care and operate at your own risk.
Loading...