Toyota SIENNA 2004 Owner Manual
04 SIENNA_U (L/O 0301)
SECTION 1-
OPERATION OF INSTRUMENT S AND
CONTROLS
Overview of instruments and controls
Instrument panel o verview 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument cluster overview 5. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Indicator symbols on the instrument panel 6. . . . . . . . . . . . . . . . . . . . . . .
1
2004 SIENNA from Jan. ’03 Prod. (OM45408U)
1
Instrument panel overview
04 SIENNA_U (L/O 0301)
1. Side defroster outlets
2. Side vents
3. Instrument cluster
4. Center vents
5. Multi- information display or garage
door opener box
6. Front personal lights
7. Power sliding door switches
8. Power back door switch
9. Conversation mir ror
10. Electric moon roof switch
11. Auxiliary boxes
12. Glove box
13. Power window switches
14. Power door lock switches
15. Automatic transmission selector lever
16. Audio remote control switches
17. Hood lock release lever
18. Parking b rake pedal
19. Window lock switch
2
2004 SIENNA from Jan. ’03 Prod. (OM45408U)
04 SIENNA_U (L/O 0301)
1. Headlight, turn signal and front fog
light switches
2. Wiper and washer switches
3. Rear window and outside rear view
mirror defogger and windshield wiper
de- icer switch
4. Emergency flasher switch
5. Car audio
6. Power outlet main switch
7. Engine immobiliser/Theft deterrent
system indicator light
8. Air conditioning controls
9. Seat heater switches or auxiliary box
10. Auxiliary box
11. Cup holder and coin holder
12. Power outlets
13. Personal light main switch
14. Ignition switch
15. “TRAC OFF” switch
16. Cruise control switch or dynamic laser
cruise control switch
17. Dynamic laser cruise control distance
switch
2004 SIENNA from Jan. ’03 Prod. (OM45408U)
3
18. Tilt and telescopic steering lock release
lever
19. Tire pressure warning system reset
switch
20. Power sliding door main switch
(“SLIDE DOOR OFF” switch)
21. Power back door main switch
(“BACK DOOR OFF” switch)
22. Power rear view mirror control switches
23. Power quarter window switch
(“REAR VENT” switch)
24. Headlight beam level control dial
04 SIENNA_U (L/O 0301)
4
2004 SIENNA from Jan. ’03 Prod. (OM45408U)
Instrument cluster overview
04 SIENNA_U (L/O 0301)
1. Service reminder indicators and
indicator lights
2. Speedometer
3. Engine coolant temperature gauge
4. Low fuel level warning light
5. Fuel gauge
6. Dynamic laser cruise control master
warning light
7. Dynamic laser cruise control display
8. Trip meter reset knob/Ins trument panel
light control knob
9. Odometer and two trip meters
10. Tachometer
5
2004 SIENNA from Jan. ’03 Prod. (OM45408U)
Indicator symbols on the instrument panel
04 SIENNA_U (L/O 0301)
or
Brake system warning light
Driver’s seat belt reminder light
Front passenger’s seat belt reminder light
Dischar ge warning light
∗
or Malfunction indicator lamp
Low engine oil press ure warning light
∗
1
∗
1
∗
1
1
or Anti- lock brake system warning light
∗
Open door warni ng light
SRS war ning light
Vehicle skid control system/Traction control
system warning light
1
∗
1
∗
1
Low tire pressure warning light
∗
1
Low windshield washer fluid level warning
∗
1
light
∗
1
Engine oil replacement reminder light
∗
1
∗
1
∗
1
(for vehicles sold in U.S.A.)
6
2004 SIENNA from Jan. ’03 Prod. (OM45408U)
Engine immobiliser/Theft deterrent system
indicator light
Headlight high beam indicator light
Turn signal indicator lights
Automatic transmission indicator lights
Slip indicator light
Traction control system off indicator light
(two- wheel drive models)
∗
Cruise control indicator light
cruise control indicator light
2
or dynamic laser
∗
3
04 SIENNA_U (L/O 0301)
∗
1
: For details, see “Service reminder indicators and warning
buzzers” on page 165 in Section 1- 5.
∗
2
: If this light flashes, see “Cruise control” on page 190 in
Section 1- 6.
∗
3
: If this light flashes, see “Dynamic laser cruise control” on
page 193 in Section 1- 6.
Dynamic laser cruise control ready mode
indicator light
Conventional cruise control mode indicator light
7
2004 SIENNA from Jan. ’03 Prod. (OM45408U)
04 SIENNA_U (L/O 0301)
8
2004 SIENNA from Jan. ’03 Prod. (OM45408U)
04 SIENNA_U (L/O 0301)
SECTION 1-
OPERATION OF INSTRUMENT S AND
CONTROLS
Keys and Doors
Keys 10. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Engine immobiliser system 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Wireless remote control 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Front door s 21. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Sliding doors 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power sliding doors 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Back door 34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power back door 36. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power windows 41. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manual quarter windows 45. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power quarter windows 45. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hood 46. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Theft deterrent s ystem 48. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Fuel tank cap 50. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Electric moon roof 52. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2
2004 SIENNA from Jan. ’03 Prod. (OM45408U)
9
04 SIENNA_U (L/O 0301)
Keys (without engine
immobiliser system)
Your vehicle is supplied with two kinds
of keys.
1. Master keys—These keys work in every lock.
2. Sub key—This key will not work in the
glove box.
To protect items locked in the glove box
when using valet parking, leave the sub
key with the attendant.
Since the front doors and sliding doors
can be locked without a key, you should
always carry a spare master key in case
you accidentally lock your keys inside the
vehicle.
KEY NUMBER PLATE
Your key number is shown on the plate.
Keep the plate in a safe place such as
your wallet, not in the vehicle.
If you should lose your keys or if you
need additional keys, duplicates can be
made by a Toyota dealer using the key
number.
We recommend writing down the key number and storing it in a safe place.
Keys (with engine immobiliser
system)
Your vehicle is supplied with two kinds
of keys.
1. Master keys (black)—These keys work
in every lock. Your Toyota dealer will
need one of them to make a new key
with a built- in transponder chip.
2. Sub key (gray)—This key will not work
in the glove box.
A transponder chip for engine immobiliser
system has been placed in the head of
the master and sub keys. These chips are
needed to enable the system to function
correctly, so be careful not to lose these
keys. If you make your own duplicate key,
you will not be able to cancel the system
or start the engine.
10
2004 SIENNA from Jan. ’03 Prod. (OM45408U)
To protect items locked in the glove box
when using valet parking, leave the sub
key with the attendant.
Since the front doors and sliding doors
can be locked without a key, you should
always carry a spare master key in case
you accidentally lock your keys inside the
vehicle.
04 SIENNA_U (L/O 0301)
NOTICE
When using a key containing a transponder chip, observe the following
precautions:
When starting the engine, do not
use the key with a key ring resting
on the key grip and do not press
the key ring against the key grip.
Otherwise the engine may not start,
or may stop soon after it starts.
When starting the engine, do not
use the key with other transponder
keys around (including keys of other vehicles) and do not press other
key plates against the key grip.
Otherwise the engine may not start,
or may stop soon after it starts. If
this happens, remove the key once
and then insert it again after removing other transporter keys (including keys of other vehicles) from the
ring or while gripping or covering
them with your hand to start the
engine.
2004 SIENNA from Jan. ’03 Prod. (OM45408U)
11
Do not bend the key grip.
04 SIENNA_U (L/O 0301)
Do not cover the key grip with any
material that cuts off electromagnetic waves.
Do not knock the key hard against
other objects.
Do not leave the key exposed to
high temperatures for a long period,
such as on the dashboard and hood
under the direct sunlight.
Do not put the key in water or
wash it in an ultrasonic washer.
Do not use the key with electromagnetic materials.
KEY NUMBER PLATE
Your key number is shown on the plate.
Keep the plate in a safe place such as
your wallet, not in the vehicle.
If you should lose your keys or if you
need additional keys, duplicates can be
made by a Toyota dealer using the key
number.
We recommend writing down the key number and storing it in a safe place.
12
2004 SIENNA from Jan. ’03 Prod. (OM45408U)
Engine immobiliser system
The engine immobiliser system is a
theft prevention system. When you insert the key in the ignition switch, the
transponder chip in the key’s head
transmits an electronic code to the vehicle. The engine will start only when
the electronic code in the chip corresponds to the registered ID code for
the vehicle.
04 SIENNA_U (L/O 0301)
The system is automatically set when the
key is removed from the ignition switch.
The indicator light will start flashing to
show the system is set.
If any of the following indicator conditions
occurs, contact your Toyota dealer.
The indicator light stays on except
when the theft deterrent system is setting or activating. (See “Theft deterrent
system” on page 48 in this section.)
The indicator light does not start flash-
ing when the key is removed from the
ignition switch.
The indicator light flashes unsteady.
Inserting the registered key in the ignition
switch automatically cancels the system,
which enables the engine to start. The
indicator light will go off.
For your Toyota dealer to make you a
new key with built- in transponder chip,
your dealer will need your key number
and master key. However, there is a limit
to the number of additional keys your
Toyota dealer can make for you.
If you make your own duplicate key,
you will not be able to cancel the system or start the engine.
NOTICE
Do not modify, remove or disassemble the engine immobiliser system. If any unauthorized changes or
modifications are made, the proper
operation of the system cannot be
guaranteed.
13
2004 SIENNA from Jan. ’03 Prod. (OM45408U)
For vehicles sold in U.S.A.
04 SIENNA_U (L/O 0301)
Wireless remote control
For vehicles sold in Canada
FCC ID: MOZ RI- 21BTY
MADE IN U.S.A.
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
CAUTION
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
This device complies with RSS-210 of
Industry Canada. Operation is subject to
the following two conditions:
(1) This device may not cause interference, and (2) this device must accept
any interference, including interference
that may cause undesired operation of
the device.
Locking operation (type A)
Unlocking operation (type A)
14
2004 SIENNA from Jan. ’03 Prod. (OM45408U)
04 SIENNA_U (L/O 0301)
Locking operation (type B)
The wireless remote control system is
designed to lock or unlock all the side
doors and back door, or activate the
panic mode from a distance within
approximately 1 m (3 ft.) of the vehicle.
On some models, the system also allows you to activate the theft deterrent
system from the same distance.
LOCKING AND UNLOCKING THE
DOORS
To lock and unlock all the doors, push
the switches of the transmitter slowly
and securely.
To lock: Push the “
the side doors and back door are locked
simultaneously. At this time one beep will
be heard, turn signal lights will flash once.
Check to see that the doors are securely
locked.
If any of the doors is not securely closed,
or if the key is in the ignition switch,
locking cannot be performed by the “
(lock) switch and a beep will sound continuously for 10 seconds. However, if the
key is in the ignition, a beep will not
sound.
” (lock) switch. All
To stop the beep, close all the side doors
and back door securely or push the “
(unlock) switch.
The buzzer can be disabled. For details,
contact your Toyota dealer.
To unlock: Push the “
once to unlock only the driver’s door.
Pushing the switch twice within 3 seconds
unlocks all the doors simultaneously. Each
time the “
two beeps will be heard, turn signal lights
will flash twice.
This double switch operation to unlock all
the side doors and back door can be
changed to a single switch operation. For
details, contact your Toyota dealer.
When the “
pressed, the front personal lights and ignition switch light come on. The lights remains on for about 15 seconds unless any
of the side doors or back door are opened
”
then and closed. (For further information,
see “Front personal lights” on page 154
and/or “Ignition switch light” on page 156
in Section 1-4.)
” (unlock) switch is pushed,
” (unlock) switch is
” (unlock) switch
”
Unlocking operation (type B)
15
2004 SIENNA from Jan. ’03 Prod. (OM45408U)
You have 30 seconds to open a door after
using the wireless remote unlock feature.
If a door is not opened by then, all the
side doors and back door will automatically lock again.
The timing for the automatic door lock
function can be changed. For details, contact your Toyota dealer.
If the “
switch is kept pressed in, the locking or
unlocking operation is not repeated. Release the switch and then push again.
The following adjustments can be made in
this system. For details, contact your
Toy ota dealer.
” (lock) or the “ ” (unlock)
Cancelling the wireless door locking or
unlocking function
Cancelling the flash of the turn signal
lights
Cancelling the beep sound
04 SIENNA_U (L/O 0301)
Right side power sliding door (type A)
Left side power sliding door
OPENING AND CLOSING THE SLIDING
DOOR (vehicles with the power sliding
door)
Push the switch of the wireless remote
control transmitter about one second.
The power sliding door opens and
closes completely.
Left side power sliding door—
To open: Push the “
To close: Push the “
” switch.
” switch again.
16
Right side power sliding door (type B)
2004 SIENNA from Jan. ’03 Prod. (OM45408U)
04 SIENNA_U (L/O 0301)
Right side power sliding door—
To open: Push the “
To close: Push the “
Opening operation can be performed by
the switches under the following conditions
only:
” switch.
” switch again.
The sliding door is unlocked.
The power sliding door system is on.
(The “SLIDE DOOR OFF” switch on the
instrument panel is pushed out.)
The key is not in the ignition switch.
The sliding door is between the fully-
closed position and half- opened position.
The sliding door stops at the half- opened
position when the window is opened more
than about 15 cm (6 in.).
The left side power sliding door does not
operate when the fuel filler door is
opened.
Closing operation can be performed by the
wireless remote control switches under the
following conditions only:
The power sliding door system is on.
(The “SLIDE DOOR OFF” switch on the
instrument panel is pushed out.)
The key is not in the ignition switch.
The sliding door is between the fully-
opened position and half- opened position.
The sliding door operation by the wireless
remote control can be changed or disabled. For details, contact your Toyota
dealer.
Type A
Type B
17
2004 SIENNA from Jan. ’03 Prod. (OM45408U)
04 SIENNA_U (L/O 0301)
OPENING AND CLOSING THE BACK
DOOR (vehicles with the power back
door)
Push the “
remote control transmitter about one
second. The power back door opens
and closes completely.
When closing or opening the back door,
two beeps will be heard and the turn signal lights will flash twice.
Opening operation can be performed by
the switch under the following conditions
only:
” switch of the wireless
The back door is unlocked.
The power back door system is on.
(The “BACK DOOR OFF” switch on the
instrument panel is pushed out.)
The key is not in the ignition switch.
The back door is between the fully-
closed position and half- opened position.
Closing operation can be performed by the
switch under the following conditions only:
The power back door system is on.
(The “BACK DOOR OFF” switch on the
instrument panel is pushed out.)
The key is not in the ignition switch.
The back door is between the fully-
opened position and half- opened position.
The back door operation by the wireless
remote control can be changed or disabled. For details, contact your Toyota
dealer.
ACTIVATING PANIC MODE
Pushing and holding the “
switch blows the horn intermittently
and flashes the headlights, tail lights
and turns on the front personal lights.
The “
vehicle theft when you witness anyone attempting to break into or damage your
vehicle.
” (panic) switch is used to deter
” (panic)
18
2004 SIENNA from Jan. ’03 Prod. (OM45408U)
04 SIENNA_U (L/O 0301)
The alarm will last for one minute. To stop
alarm midway, do the following:
Push any of the switch on the wireless
remote control transmitter.
Lock or unlock either front doors or
back door with the key.
Turn the ignition key from the “LOCK”
to “ON” position.
The panic mode does not work when the
ignition key is in the “ON” position.
This alarm function can be disabled. For
details, contact your Toyota dealer.
WIRELESS REMOTE CONTROL
TRANSMITTER
The wireless remote control transmitter is
an electronic component. Observe the following instructions in order not to cause
damage to the wireless remote control
transmitter.
Do not leave the wireless remote con-
trol transmitter on places where the
temperature becomes high such as on
the dashboard.
Do not disassemble it.
Avoid knocking it hard against other
objects or dropping it.
Avoid putting it in water.
You can use up to 4 wireless remote control transmitters for the same vehicle.
Contact your Toyota dealer for detailed
information.
If the wireless remote control transmitter
does not actuate the doors or alarm, or
operate from a normal distance:
Check for closeness to a radio trans-
mitter such as a radio station or an
airport which can interfere with normal
operation of the transmitter.
The battery may have been consumed.
Check the battery in the transmitter. To
replace the battery, see “REPLACING
TRANSMITTER BATTERY”.
If you lose your wireless remote control
transmitter, contact your Toyota dealer as
soon as possible to avoid the possibility
of theft, or an accident. (See “If you lose
your wireless remote control transmitter”
on page 413 in Section 4.)
MODEL/FCC IDs:
Transmitter: GQ43VT20T
Receiver: GQ43VT29R
IC (Canada) IDs:
Transmitter: 1470A- 1T
Receiver: 1470A- 1R
MADE IN U.S.A.
This complies with Part 15 of the FCC
rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful
interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
19
2004 SIENNA from Jan. ’03 Prod. (OM45408U)
REPLACING TRANSMITTER BATTERY
For replacement, use a CR2032 lithium
battery or equivalent.
CAUTION
Special care should be taken to prevent small children from swallowing
the removed transmitter battery or
components.
NOTICE
When replacing the transmitter battery, be careful not to lose the components.
Replace only with the same or
equivalent type recommended by a
Toyota dealer.
Dispose of used batteries according
to the local laws.
04 SIENNA_U (L/O 0301)
1. Using a coin or equivalent, open the
transmitter case.
2. Remove the discharged transmitter battery.
NOTICE
Do not bend the terminals.
Replace the transmitter battery by following these procedures:
20
2004 SIENNA from Jan. ’03 Prod. (OM45408U)
04 SIENNA_U (L/O 0301)
Be careful not to bend the electrode
of the transmitter battery insertion
and that dust or oils do not adhere
to the transmitter case.
Close the transmitter case securely.
After replacing battery, check that the
transmitter operates properly. If the transmitter still does not operate properly, contact your Toyota dealer.
Front doors
3. Put a new transmitter battery with positive (+) side up.
Close the transmitter case securely.
NOTICE
Make sure the positive side and
negative side of the transmitter battery is faced correctly.
Do not replace the battery with wet
hands. Water may cause unexpected
rust.
Do not touch or move any components inside of the transmitter, or
it may interfere with proper operation.
LOCKING AND UNLOCKING WITH KEY
Insert the key into the keyhole and turn
it.
To lock: Turn the key forward.
To unlock: Turn the key backward.
All the side doors and back door lock and
unlock simultaneously with either front
door. In the driver’s door lock, turning the
key once will unlock the driver’s door and
twice in succession will unlock all the
doors simultaneously.
This double key turning operation to unlock all the side doors and back door can
be changed to a single key turning operation. For details, contact your Toyota dealer.
21
2004 SIENNA from Jan. ’03 Prod. (OM45408U)
04 SIENNA_U (L/O 0301)
When either front door is unlocked with a
key, the front personal light and ignition
switch light will come on and remain on
for about 15 seconds before fading out.
(For details, see “Front personal lights” on
page 154 and “Ignition switch light” on
page 156 in Section 1-4.)
LOCKING AND UNLOCKING WITH
INSIDE LOCK KNOB
Move the lock knob.
To lock: Push the knob forward.
To unlock: Pull the knob backward.
The front doors can be opened by pulling
the inside handles even if the lock knobs
are in the locked position.
CAUTION
Do not pull the inside handle of the
front doors while driving. The doors
will open and an accident may occur.
Toyota strongly recommends that all
children be placed in the rear seat of
the vehicle.
Closing the door with the lock knob in the
lock position will also lock the door. Be
careful not to lock your keys in the vehicle.
The front doors cannot be locked if you
leave the key in the ignition switch.
22
2004 SIENNA from Jan. ’03 Prod. (OM45408U)
04 SIENNA_U (L/O 0301)
Driver’s side
LOCKING AND UNLOCKING WITH
POWER DOOR LOCK SWITCH
Push the switch.
To lock: Push the switch down on the
front side.
To unlock: Push the switch down on the
rear side.
Operating the switch simultaneously locks
or unlocks all the side doors and back
door.
If you do either of the following, no side
door or back door can be unlocked with
the power door lock switch.
Lock all the side doors and back door
with the key or wireless remote control
transmitter when all the side doors and
back door are closed.
Open the driver’s door or front passen-
ger’s door and move the inside lock
knobs of both front doors to the lock
position, then close the front doors.
The power door lock switch can be reset
in the following ways.
Turn the ignition key to “ON”.
Unlock all the side doors and back
door with the key or wireless remote
control transmitter.
Unlock the driver’s door or front pas-
senger’s door with the inside lock
knob, and then unlock all the doors
and back door with the power door
lock switch.
CAUTION
Before driving, be sure that the doors
are closed and locked, especially
when small children are in the vehicle. Along with the proper use of
seat belts, locking the doors helps
prevent the driver and passengers
from being thrown out from the vehicle during an accident. It also helps
prevent the doors from being opened
unintentionally.
Front passenger’s side
23
2004 SIENNA from Jan. ’03 Prod. (OM45408U)
Automatic door locking function:
All the side doors and back door are
locked automatically when the automatic
transmission selector lever is moved out
of the “P” position with the engine running
and all the side doors and back door are
closed.
This automatic door locking function linked
with the shift position can be disabled. For
details, contact your Toyota dealer.
You can add the automatic door locking
function linked with vehicle speed. (When
the vehicle speed reaches 20 km/h (12
mph) or higher, all the side doors and
back door are locked automatically.) For
details, contact your Toyota dealer.
04 SIENNA_U (L/O 0301)
Sliding doors
LOCKING AND UNLOCKING WITH
INSIDE LOCK KNOB
Move the lock knob.
To lock: Move the knob forward.
To unlock: Move the knob backward.
The sliding doors will be locked simultaneously with the power door lock switch,
key or wireless remote control. (For
instructions, see “Front doors” on page 21
or “Wireless remote control” on page 14
in this section.)
Closing the sliding door with the lock knob
in the lock position will also lock the sliding door. Be careful not to lock your keys
in the vehicle.
CLOSING THE FULLY- OPENED SLIDING
DOOR
To close the fully- opened sliding door, pull
the inside or outside handle and then
close the door.
CAUTION
Before driving, be sure that the doors
are closed and locked, especially
when small children are in the vehicle. Along with the proper use of
seat belts, locking the doors helps
prevent the passengers from being
thrown out from the vehicle during an
accident. It also helps prevent the
doors from being opened unintentionally.
24
2004 SIENNA from Jan. ’03 Prod. (OM45408U)
CAUTION
When closing the sliding door, con-
firm safety of the area around.
Keep the heads, hands and other
parts of the bodies of all occupants
away from the sliding door. Otherwise, the closing door may cause
an unexpected serious injury.
When the vehicle is stopped on a
slope, the door will slide faster
when opening or closing, so be especially careful that the passengers
do not get hit or pinched by the
door.
04 SIENNA_U (L/O 0301)
When stopping on a downward
slope, open the door fully while
passengers are getting on or off.
Do not pull the outside handle or
inside handle while the door is
open as the door could suddenly
close by itself causing injury.
NOTICE
Do not close the sliding door by applying the brakes. Doing so could
cause the door to be damaged.
When the fuel filler door is opened, the
left side siding door will not open.
Close the fuel filler door securely and
then operate the sliding door.
NOTICE
Avoid forcibly opening the left side
sliding door fully when the fuel filler
door is opened. Otherwise, the fuel
filler door may be damaged.
25
2004 SIENNA from Jan. ’03 Prod. (OM45408U)
04 SIENNA_U (L/O 0301)
Power sliding doors—
—Power sliding door main switch
(“SLIDE DOOR OFF” switch)
On Off
When the sliding door window is
opened more than about 15 cm (6 in.),
the sliding door will stop at halfopened position. Close the window and
then operate the sliding door.
CAUTION
Do not leave the sliding door at halfopened position. If the vehicle is
stopped on a downward slope, it may
move and cause an unexpected injury.
26
SLIDING DOOR CHILD- PROTECTORS
Open the sliding door fully and move
the lock lever to the “LOCK” position
as shown on the label. Then close the
sliding door.
If the child- protector is locked, you cannot
open the sliding door from the inside. We
recommend using this feature whenever
small children are in the vehicle.
This switch is used to turn on and off
the power sliding door system. In order
to operate the power sliding door, the
“SLIDE DOOR OFF” switch on the instrument panel must be pushed out.
(The orange line on the top of the
switch indicates that the power sliding
door system is on.) To disable the power sliding door feature, push in the
switch.
2004 SIENNA from Jan. ’03 Prod. (OM45408U)
When the power sliding door system is
on, you can open and close the sliding
door with the power sliding door switches
on the overhead console or wireless remote control transmitter even if the sliding
door child- protector is locked.
CAUTION
Do not leave small children or pets
unattended in your vehicle. They
could operate the power sliding
door and injure themselves or others. Turn off the power sliding door
system when the power sliding door
is not in use.
When jacking up the vehicle, turn
off the power sliding door system
and close the sliding door completely.
04 SIENNA_U (L/O 0301)
—Manual operatio n
NOTICE
When your vehicle goes through an
automatic car wash, make sure the
power sliding door system is off.
LOCKING AND UNLOCKING WITH
INSIDE LOCK KNOB
Move the lock knob.
To lock: Move the knob forward.
To unlock: Move the knob backward.
The sliding doors will be locked simultaneously with the power door lock switch,
key or wireless remote control. (For
instructions, see “Front doors” on page 21
or “Wireless remote control” on page 14
in this section.)
27
2004 SIENNA from Jan. ’03 Prod. (OM45408U)
04 SIENNA_U (L/O 0301)
Closing the sliding door with the lock knob
in the lock position will also lock the sliding door. Be careful not to lock your keys
in the vehicle.
CLOSING THE FULLY-OPENED SLIDING
DOOR
To close the fully- opened sliding door, pull
the inside or outside handle and then
close the door.
CAUTION
Before driving, be sure that the doors
are closed and locked, especially
when small children are in the vehicle. Along with the proper use of
seat belts, locking the doors helps
prevent the passengers from being
thrown out from the vehicle during an
accident. It also helps prevent the
doors from being opened unintentionally.
Sliding door closer: When the sliding
door has not been fully closed, it is automatically closed completely even if the
power sliding door system is off.
CAUTION
Careful attention is needed so as
not to get your fingers trapped as
the sliding door automatically
closes when it has not been fully
closed.
Never allow a child to operate the
sliding door.
NOTICE
Do not apply excessive force when
the sliding door closer is operating.
Otherwise, the sliding door closer
may be damaged.
CAUTION
When closing the sliding door, con-
firm safety of the area around.
Keep the heads, hands and other
parts of the bodies of all occupants
away from the sliding door. Otherwise, the closing door may cause
an unexpected serious injury.
When the vehicle is stopped on a
slope, the door will slide faster
when opening or closing, so be especially careful that the passengers
do not get hit or pinched by the
door.
28
2004 SIENNA from Jan. ’03 Prod. (OM45408U)
When stopping on a downward
slope, open the door fully while
passengers are getting on or off.
Do not pull the outside handle or
inside handle while the door is
open as the door could suddenly
close by itself causing injury.
NOTICE
Do not close the sliding door by applying the brakes. Doing so could
cause the door to be damaged.
04 SIENNA_U (L/O 0301)
When the fuel filler door is opened, the
left side siding door will not open.
Close the fuel filler door securely and
then operate the sliding door.
NOTICE
Avoid forcibly opening the left side
sliding door fully when the fuel filler
door is opened. Otherwise, the fuel
filler door may be damaged.
When the sliding door window is
opened more than about 15 cm (6 in.),
the sliding door will stop at halfopened position. Close the window and
then operate the sliding door.
CAUTION
Do not leave the sliding door at halfopened position because the door will
unlock after 30 minutes. If the vehicle
is stopped on a downward slope, it
may move and cause an unexpected
injury.
29
2004 SIENNA from Jan. ’03 Prod. (OM45408U)
04 SIENNA_U (L/O 0301)
NOTICE
To prevent the battery from being discharged, do not leave the sliding door
at half- opened position.
CAUTION
Make sure to turn off the power sliding door system after locking the
child- protectors.
SLIDING DOOR CHILD- PROTECTORS
Open the sliding door fully and move
the lock lever to the “LOCK” position
as shown on the label. Then close the
sliding door.
If the child- protector is locked, you cannot
open the sliding door from the inside. We
recommend using this feature whenever
small children are in the vehicle.
If the power sliding door system is on, the
child- protector feature is cancelled by the
power sliding door switch on the front
overhead console or wireless remote
control.
30
2004 SIENNA from Jan. ’03 Prod. (OM45408U)
Loading...