Toyota Highlander 2004 Owner's Manual
’04 HIGHLANDER_U (L/O 0308)
SECTION 1− 1
OPERATION OF INSTRUMENTS AND
CONTROLS
Overview of instruments and controls
Instrument panel over view 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Instrument cluster overview 8. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Indicator symbols on t he instrument panel 9. . . . . . . . . . . . . . . . . . . . . . .
2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)
1
Instrument panel overview
"Vehicles with rear seat entertainment system (view A)
’04 HIGHLANDER_U (L/O 0308)
1. Side defroster outlets
2. Instrument cluster
3. Center vents
4. Electr ic moon roof switc h and personal
lights
5. Garage door opener
6. Auxiliary boxes
7. Side vents
8. Power door lock switches
9. Power window switches
10. Glove box
11. Automatic transmission selector lever
12. Rear ashtray
13. Input terminal adapter
14. Power outlets
15. Cup holder
16. Container
17. Front ashtray
18. Audio remote control switches
19. Hood lock release lever
20. Parking b rake pedal
21. Window lock switch
2
2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)
"Vehicles without rear seat entertainment system (view A)
’04 HIGHLANDER_U (L/O 0308)
1. Side defroster outlets
2. Instrument cluster
3. Center vents
4. Electr ic moon roof switc h and personal
lights
5. Garage door opener
6. Auxiliary boxes
7. Side vents
8. Power door lock switches
9. Power window switches
10. Glove box
11. Automatic transmission selector lever
12. Rear ashtray
13. Cup holder
14. Container
15. Power outlet
16. Front ashtray
17. Audio remote control switches
18. Hood lock release lever
19. Parking b rake pedal
20. Window lock switch
2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)
3
"Vehicles with manual air conditioning cont rols (view B)
’04 HIGHLANDER_U (L/O 0308)
1. Headlight, turn signal and front fog
light switches
2. Wiper and washer switches
3. Emergency flasher switch
4. Clock
5. Front passenger’s seat belt reminder
light
6. Rear window and outside rear view
mirror defogger and windshield wiper
de−icer switch
7. Air conditioning controls
8. Car audio
9. “AIRBAG ON” and “AIRBAG OFF”
indicator lights
10. Snow mode button
11. Seat heater switches
12. Cigarette lighter
13. “TRAC OFF” switch
(two−wheel drive models)
14. Cruise control switch
15. Ignition switch
16. Tilt steering lock release lever
17. Tire pressure warning system reset
switch
4
2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)
18. Power outlet (115 VAC) main switch
19. Rear heater main switch
20. Theft deterrent system/engine
immobilizer system indicator light
21. Power rear view mirror control switches
’04 HIGHLANDER_U (L/O 0308)
2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)
5
"Vehicles with aut omatic air condit ioning controls (view B)
’04 HIGHLANDER_U (L/O 0308)
1. Headlight, turn signal and front fog
light switches
2. Wiper and washer switches
3. Emergency flasher switch
4. Clock
5. Front passenger’s seat belt reminder
light
6. Air conditioning controls and
multi−information display
7. Rear window and outside rear view
mirror defogger and windshield wiper
de−icer switch
8. Car audio
9. “AIRBAG ON” and “AIRBAG OFF”
indicator lights
10. Snow mode button
11. Seat heater switches
12. Cigarette lighter
13. “TRAC OFF” switch
(two−wheel drive models)
14. Cruise control switch
15. Ignition switch
16. Tilt steering lock release lever
17. Tire pressure warning system reset
switch
6
2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)
18. Power outlet (115 VAC) main switch
19. Rear heater main switch
20. Theft deterrent system/engine
immobilizer system indicator light
21. Power rear view mirror control switches
’04 HIGHLANDER_U (L/O 0308)
2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)
7
Instrument cluster overview
’04 HIGHLANDER_U (L/O 0308)
1. Tachometer
2. Service reminder indicators and
indicator lights
3. Speedometer
8
4. Fuel gauge
5. Low fuel level warning light
6. Engine coolant temperature gauge
7. Trip m eter res et knob
8. Odometer and two trip meters
9. Instrument panel light control knob
2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)
Indicator symbols on the instrument panel
’04 HIGHLANDER_U (L/O 0308)
∗
or
Brake system warning light
Driver’s seat belt reminder light
Front passenger’s seat belt reminder light
Discharge warning light
Low engine oil pressure warning light
1
∗
1
∗
1
∗
1
∗
1
or
Anti−lock brake system warning light
∗
Open door warning light
Automatic transmission fluid temperature
warning light
∗
1
SRS warning light
1
∗
1
Vehicle stability control system warning light
Low tire pressure warning light
∗
or
Malfunction indicator lamp
1
Low windshield washer fluid level warning
∗
1
light
∗
1
∗
1
∗
1
2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)
9
Engine oil replacement reminder light
(for vehicles sold in U.S.A.)
’04 HIGHLANDER_U (L/O 0308)
∗
1
Snow mode indicator light
10
“AIRBAG ON” indicator light
“AIRBAG OFF” indicator light
Headlight high beam indicator light
Turn signal indicator lights
∗
1
: For details, see “Service reminder indicators and warning
buzzers” on page 129 in Section 1−6.
∗
2
: If this light flashes, see “Cruise control” on page 159 in
Slip indicator light
Traction control system off indicator light
∗
Cruise control indicator light
2
Section 1−7.
or
Automatic transmission indicator lights
Overdrive−off indicator light
2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)
’04 HIGHLANDER_U (L/O 0308)
SECTION 1− 10
OPERATION OF INSTRUMENTS AND
CONTROLS
Other equipment
Multi−information display 258. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Clock 259. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Compass 260. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cigarette lighter and ashtrays 264. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power outlet s 265. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power outlet 266. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Glove box 267. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Garage door opener 267. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Auxiliary boxes 270. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Container 272. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Cup holders 273. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Bottle holders 275. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Tie−down hooks 275. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Luggage cover 276. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Roof luggage carrier 278. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Floor mat 280. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
For information about the clock of a vehicle equipped with
Navigation system, please refer to the separate “Navigation
System Owner’s Manual”.
2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)
257
Multi−information display
Air conditioning system on—
Air conditioning system off—
’04 HIGHLANDER_U (L/O 0308)
The multi−information display indicates
the following information.
1. Outside temperature
2. Average vehicle speed
3. Average fuel consumption
4. Instantaneous fuel consumption
5. Driving time
6. Air conditioning system on—The air
conditioned temperature is displayed.
Air conditioning system off—The air
conditioned temperature is not displayed.
Every time you push the “INFO” button,
the display toggles through this information.
The displayed values in the multi−informa-
tion display indicate general driving conditions. Accuracy varies with driving habits
and road conditions.
You can adjust the air conditioned temperature while the multi−information is operating. 5 seconds has been passed after adjusting the temperature or pushing the
“INFO” button, the display will be back to
the multi−information display.
1. Outside temperature
(“OUTSIDE TEMP”)
The outside temperature display indicates the outside air temperature.
The displayed temperature ranges from
−22F (−30C) up to 122F (50C) .
If there is some abnormality in the con-
nection of the outside air temperature sensor, “−−F” (“−−C”) will appear on the
display. If “−−F” (“−−C”) appears on the
display, contact your Toyota dealer.
There may be a case that “−−F” (“−−C”)
appears momentarily when the ignition is
quickly turned to “ON”. It is normal if it
goes out soon.
2. Average vehicle speed
(“AVG MPH” or “AVG km/h”)
Average vehicle speed is calculated and
displayed based on total driving distance and total driving time with the
engine running.
The displayed value is updated every 10
seconds .
To reset the calculation, push the “INFO”
button for more than 1 second.
258
2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)
3. Average fuel consumption
(“AVG MPG” or “AVG L/100 km”)
Average fuel consumption is calculated
and displayed based on total driving
distance and total fuel consumption
with the engine running.
The displayed value is updated every 10
seconds .
4. Instantaneous fuel consumption
(“MPG” or “L/100 km”)
The instantaneous fuel consumption is
calculated and displayed based on distance and fuel consumption for 1 seconds with the engine running.
The displayed value is updated every 2
seconds .
Note that an accurate figure may not be
shown in the following cases.
When the vehicle is stopped with the
engine running, the display will indicate
the extremely high fuel consumption.
When the vehicle is driving down a
long slope, applying the engine brake,
the display will indicate the extremely
low fuel consumption.
The calculation is reset when the ignition
switch is turned off.
’04 HIGHLANDER_U (L/O 0308)
Clock
5. Driving time (“E/T”)
The elapsed time after the engine starts
is displayed.
When the engine is started, driving time
is counted from 0:00. Up to 11:59 (11
hours, 59 minutes) can be displayed.
When the driving time exceeds 11:59, the
counter returns to 0:00.
The calculation is reset when the ignition
switch is turned off.
The digital clock indicates the time.
The key must be in the “ACC” or “ON”
position.
To reset the hour: Push the “H” button.
To reset the minutes: Push the “M” button.
If the electrical power source has been
disconnected from the clock, the time display will automatically be set to 1:00 (one
o’clock).
259
2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)
Compass
The direction is indicated on the inside
rear view mirror.
If the ignition switch was turned off with
the system on, the system will automatically turn back on when the ignition switch
is turned on.
Push the “COMP” switch to turn the compass system on and off.
’04 HIGHLANDER_U (L/O 0308)
The compass indicates the direction
that the vehicle is heading. In the
above case, it shows that the vehicle is
heading north.
Displays
N
NE
E
SE
S
SW
W
NW
The compass may not show the correct
direction in the following conditions:
The vehicle is stopped immediately af-
ter turning.
The compass does not adjust while the
vehicle is stopped.
The ignition switch is turned off imme-
diately after turning.
The vehicle is on an inclined surface.
Directions
North
Northeast
East
Southeast
South
Southwest
West
Northwest
The vehicle is in a place where the
earth’s magnetic field is subject to interference by artificial magnetic fields
(underground parking, under a steel
tower, between buildings, roof parking,
near a crossing, near a large vehicle,
etc.).
The vehicle is magnetized. (There is a
magnet or a metal object on or near
the inside rear view mirror.)
The battery has been disconnected.
Your vehicle is out of the set zone. Refer
to the “CALIBRATING THE COMPASS” below to set the zone number.
The compass works to calibrate the direction automatically while the vehicle is in
motion, if deviation is small.
For additional precision or for complete
calibrating, see “CALIBRATING THE
COMPASS” below.
260
2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)
’04 HIGHLANDER_U (L/O 0308)
Compass sensor
The compass sensor is in the inside
rear view mirror.
NOTICE
Do not put magnets or a metal object
on or near the inside rear view mirror
of the vehicle. Doing this may cause
malfunction of the compass sensor.
CALIBRATING THE COMPASS (deviation
calibration)
The direction display on the compass
deviates from the true direction determined by the earth’s magnetic field. The
angle of deviation varies according to the
geographic position of the vehicle.
To adjust this deviation, stop the vehicle,
then push and hold the “COMP” switch
until the zone number appears on the display. Then push the “COMP” switch, referring to the following map to select the
number of the zone where the vehicle is.
261
2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)
’04 HIGHLANDER_U (L/O 0308)
Hawaii: 6 Samoa: 5 Guam: 7
Saipan: 7 Puerto Rico: 10
After calibration, leaving the system for
several seconds returns it to the compass
mode.
CAUTION
Do not adjust the display while the
vehicle is moving. Be sure to adjust
the display only when the vehicle is
stopped.
Zone number
262
2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)
CALIBRATING THE COMPASS (circling
calibration)
Sometimes the direction display on the
compass may not change after a turn. To
rectify this, stop the vehicle and push and
hold the “COMP” switch until “C” appears
on the display.
If “C” appears on the display because of
a drastic change in the magnetic field,
perform circling calibration.
’04 HIGHLANDER_U (L/O 0308)
Drive the vehicle in a circle at 8 km/h (5
mph) or less. If there is not enough space
to drive in a circle, drive around the
block .
After driving 1 to 3 circles in the above
method, calibration is completed when the
direction is shown on the display.
If calibration cannot be performed because
of the magnetized vehicle etc., take your
vehicle to Toyota dealer.
Perform circling calibration just after
you have purchased your Toyota. And
then always perform circling calibration
after the battery has been removed, replaced or disconnected.
Do not perform circling calibration of
the compass in a place where the
earth’s magnetic field is subject to interference by artificial magnetic fields
(underground parking, under a steel
tower, between buildings, roof parking,
near a crossing, near a large vehicle,
etc.).
During calibration, do not operate elec-
tric systems (moon roof, power windows, etc.) as they may interfere with
the calibration.
263
2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)
CAUTION
When doing the circling calibration,
be sure to secure a wide space,
and watch out for people and vehicles in the neighborhood. Do not
violate any local traffic rules while
performing circling calibration.
Do not adjust the display while the
vehicle is moving. Be sure to adjust
the display only when the vehicle is
stopped.
’04 HIGHLANDER_U (L/O 0308)
Cigarette lighter and ashtrays
Cigarette lighter
Rear ashtray
CIGARETTE LIGHTER
To use the cigarette lighter, press it in.
After it finishes heating up, it automatically pops out ready for use.
If the engine is not running, the key must
be in the “ACC” position.
Do not hold the cigarette lighter pressed
in.
Use a Toyota genuine cigarette lighter or
equivalent for replacement.
264
Front ashtray
2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)
ASHTRAYS
Front ashtray: To use the ashtray, open
the lid.
When finished with your cigarette, thoroughly extinguish it in the ashtray to prevent other cigarette butts from catching
fire. After using the ashtray, push it back
in completely.
To remove the ashtray, pull the lid and
pull it out.
Rear ashtray: To use the ashtray, pull
it out.
When finished with your cigarette, thoroughly extinguish it in the ashtray to prevent other cigarette butts from catching
fire. After using the ashtray, push it back
in completely.
To remove the ashtray, press down on the
lock spring plate and pull out.
CAUTION
To reduce the chance of injury in
case of an accident or sudden stop
while driving, always completely close
the ashtray after use.
’04 HIGHLANDER_U (L/O 0308)
Power outlets (12 VDC)
Front
The power outlets (12 VDC) are designed for power supply for car accessories.
The key must be in the “ACC” or “ON”
position for the power outlets to be used.
NOTICE
z To prevent the fuse from being
blown, do not use the electricity
over the total vehicle capacity of
12VDC/120W (front and rear outlets
together).
z To prevent the battery from being
discharged, do not use the power
outlets longer than necessary when
the engine is not running.
z Close the power outlet lids when
the power outlets are not in use.
Inserting a foreign object other than
the appropriate plug that fits the
outlet, or allowing any liquid into
the outlet may cause electrical failure or short circuits.
Rear
265
2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)
Power outlet (115 VAC)
’04 HIGHLANDER_U (L/O 0308)
NOTICE
z To prevent the battery from being
discharged, do not use the power
outlet longer than necessary when
the engine is not running.
z Close the power outlet lid when the
power outlet is not in use. Inserting
a foreign object other than the appropriate plug that fits the outlet
may cause electrical failure or short
circuits.
This power outlet (115 VAC) is designed
for use as a power supply for electric
appliances in the vehicle.
The key must be in the “ON” position for
the power outlet to be used.
The maximum capacity for this power outlet is 115 VAC/100W. If you attempt to
use an appliance that requires more than
115 VAC or 100W, the protection circuit
will activate and cut the power supply.
The power supply will restart automatically
when you use an appliance that operates
within the 115 VAC/100W limits.
266
Main switch
To use the power outlet, push the main
switch on the instrument panel.
An indicator light will illuminate to indicate
that the power outlet is ready for use.
Push the main switch once again to turn
the power outlet off. When the power outlet is not in use, make sure that the main
switch is turned off.
The power outlet is not designed for
the following electric appliances even
though their power consumption is under 115 VAC/100W. These appliances
may not operate properly.
2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)
Appliances with high initial peak watt-
age: cathode−ray tube type televisions,
compressor−driven refrigerators, electric
pumps, electric tools, etc.
Measuring devices which process pre-
cise data: medical equipment, measuring instruments, etc.
Other appliances requiring an extremely
stable power supply: microcomputer−
controlled electric blankets, touch sensor lamps, etc.
Certain electrical appliances may cause
radio noise.
’04 HIGHLANDER_U (L/O 0308)
Glove box Garage door opener
To use the glove box, do this.
To open: Pull the lever.
With the instrument panel lights on, the
glove box light will come on when the
globe box is open.
To lock: Insert the master key and turn it
clockwise.
The garage door opener (
Universal Transceiver) is manufactured
under license from HomeLink
be programmed to operate garage
doors, gates, entry doors, door locks,
home lighting systems, and security
systems, etc.
and can
CAUTION
To reduce the chance of injury in
case of an accident or a sudden stop,
always keep the glove box door
closed while driving.
267
2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)
’04 HIGHLANDER_U (L/O 0308)
(a) Programming the HomeLink
The HomeLink in your vehicle has 3
buttons and you can store one program
for each button.
To ensure correct programming into the
HomeLink
, install a new battery in the
hand−held transmitter prior to programming.
The battery side of the hand−held transmitter must be pointed away from the
HomeLink
during the programming process.
For Canadian users, follow the procedure
in “Programming an entrance gate/programming all devices in the Canadian
market”.
1. Decide which of 3 HomeLink
buttons
you want to program.
2. Place your hand−held garage transmitter 25 to 75 mm (1 to 3 in.) away from
the surface of the HomeLink
.
Keep the indicator light on the HomeLink
in view while programming.
3. Simultaneously press and hold the
hand−held garage transmitter button
along with the selected HomeLink
ton.
4. When the indicator light on the
HomeLink
changes from a slow to a
rapid flash after 20 seconds, you can
release both buttons.
5. Test the operation of the HomeLink
pressing the newly programmed button.
If programming a garage door opener,
check to see if the garage door opens
and closes.
If the garage door does not operate, identify if your garage transmitter is of the
“Rolling Code” type. Press and hold the
programmed HomeLink
button. The garage door has the rolling code feature if
the indicator light (on the HomeLink
flashes rapidly and then remains lit after
2 seconds. If your garage transmitter is
the “Rolling Code” type, proceed to the
heading “Programming a rolling code system”.
6. Repeat steps 2 through 5 for each remaining HomeLink
button to program
another device.
but-
by
Programming a rolling code system
If your device is “Rolling Code”
equipped, it is necessary to follow
steps 1 through 4 under the heading
“Programming the HomeLink
proceeding with the steps listed below.
1. Locate the “training” button on the ceiling mounted garage door opener motor.
The exact location and color of the
button may vary by brand of garage
door opener. Refer to the owner’s
guide supplied by the garage door
opener manufacturer for the location of
this “training” button.
2. Press the “training” button on the ceiling mounted garage door opener motor.
Following this step, you have 30 seconds
in which to initiate step 3 below.
)
3. Press and release the vehicle’s programmed HomeLink
button twice. The
garage door may open. If the door
does open, the programming process is
complete. If the door does not open,
press and release the button a third
time. This third press and release will
complete the programming process by
opening the garage door.
” before
268
2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)
’04 HIGHLANDER_U (L/O 0308)
The ceiling mounted garage door opener
motor should now recognize the
HomeLink
unit and be able activate the
garage door up/down.
4. Repeat steps 1 through 3 for each remaining HomeLink
button to program
another rolling code system.
Programming an entrance gate/programming all devices in the Canadian market
1. Decide which of the 3 HomeLink
but-
tons you want to program.
2. Place your hand−held gate/device
transmitter 25 to 75 mm (1 to 3 in.)
away from the surface of the
HomeLink
.
Keep the indicator light on the HomeLink
in view while programming.
3. Press and hold the selected
HomeLink
button.
4. Continuously press and release (cycle)
the hand−held gate/device transmitter
button every two seconds until step 5
is complete.
5. When the indicator light on the
HomeLink
changes from a slow to a
rapid flash after 20 seconds, you can
release both buttons.
6. Test the operation of the HomeLink
pressing the newly programmed button.
Check to see if the gate/device operates correctly.
7. Repeat steps 1 through 6 for each remaining HomeLink
button to program
another device.
Programming other devices
To program other devices such as home
security systems, home door locks or
lighting, contact your authorized Toyota
dealer for assistance.
Reprogramming a button
Individual HomeLink
erased, however, to reprogram a single
button, follow the procedure “Programming
the HomeLink
”.
buttons cannot be
(b) Operating the HomeLink
To operate the HomeLink, press the
appropriate HomeLink
button to activate
the programmed device. The HomeLink
indicator light should come on. The
HomeLink
continues to send the signal
for up to 20 seconds as long as the
button is pressed.
by
(c) Erasing the entire HomeLink
memory (all three programs)
To erase all previously programmed codes
at one time, press and hold down the 2
outside buttons for 20 seconds until the
indicator light flashes.
If you sell your vehicle, be sure to erase
the programs stored in the HomeLink
memory.
269
2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)
CAUTION
When programming the HomeLink
Universal Transceiver, you may be
operating a garage door or other
device. Make sure people and objects are out of the way of the garage door or other device to prevent potential harm or damage.
Do not use this HomeLink
sal Transceiver with any garage
door opener that lacks the safety
stop and reverse feature as required by federal safety standards.
(This includes any garage door
opener model manufactured before
April 1, 1982.) A garage door opener which cannot detect an object
(signaling the door to stop and reverse), does not meet current federal safety standards. Using a garage
door opener without these features
increases risk of serious injury or
death.
Univer-
’04 HIGHLANDER_U (L/O 0308)
Auxiliary boxes
This device complies with Part 15 of the
FCC Rules and with RSS−210 of the
Industry Canada. Operation is subject to
the following two conditions: (1) This
device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
WARNING: This transmitter has been
tested and complies with FCC and
Industry Canada DOC/MPAC rules.
Changes or modifications not expressly approved by the party responsible for compliance could void the
use’s authority to operate the device.
To use the auxiliary boxes, open the
lids as shown in the following illustrations.
CAUTION
To reduce the chance of injury in
case of an accident or sudden stop,
always keep the auxiliary box
closed while driving.
Type A—It is designed for holding
a light objects, do not place any
heavy objects in it. Heavy objects
may cause the holder to open and
contents to fly out resulting in injuries.
NOTICE
Type A—During hot weather, the interior of the vehicle becomes very hot.
Do not leave anything flammable or
deformable such as a lighter, glasses,
etc. inside.
270
2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)
’04 HIGHLANDER_U (L/O 0308)
Type A (ceiling)
Type B (instrument panel)
Type C (rear console)
Type D (rear console)
Type E (luggage compartment)
271
2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)
Container
’04 HIGHLANDER_U (L/O 0308)
Type F (luggage compartment)
272
This container can be used as an auxiliary holder.
CAUTION
Do not put objects in the container
which can shift, roll out or be thrown
out in the event of sudden stops or
accidents. Objects which come out of
the container can create a safety hazard due to interference with pedal operation or driver distraction.
Do not store drinks or cans which
could easily roll out.
2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)
Do not store objects which are
higher than the lower edge of the
container.
Do not store objects which are larg-
er than the width of the container.
’04 HIGHLANDER_U (L/O 0308)
Cup holders
Type A (rear console)
Type B (luggage compartment) Type C (second seat armrest)
2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)
273
’04 HIGHLANDER_U (L/O 0308)
The cup holders are designed for holding cups or drink−cans securely.
Type A—To use the holder, open the lid.
Type C—To use the holder, pull down the
second seat armrest and push the button
on the armrest.
Type A only—
The cup holder can be adjustable to the
size of the cups or drink−cans by
changing the holder position.
CAUTION
Do not place anything else other
than cups or drink−cans in the cup
holder, as such items may be
thrown about in the compartment
and possibly injure people in the
vehicle during sudden braking or in
an accident.
Type A and C—To reduce the
chance of injury in case of an accident or sudden stop while driving,
keep the cup holder closed when it
is not in use.
274
2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)
’04 HIGHLANDER_U (L/O 0308)
Bottle holders Tie−down hooks
NOTICE
Do not put a cup or open bottle in
the bottle holder because the contents may spill when the door opens
or closes.
The bottle holders are designed to hold
bottles securely.
CAUTION
Do not attempt to use the holder for
any other purpose for which it was
intended. Inappropriately sized or
shaped objects may be thrown about
in the compartment and possibly injure people in the vehicle during a
sudden braking or an accident.
To secure your luggage, u se the tie−down
hooks as shown above.
See “—Stowage precautions” on page 305
in Section 2 for precautions when loading
luggage.
CAUTION
To avoid personal injury, keep the tie−
down hooks folded in place on the
floor when not in use.
Vehicles with the third seat—When using
the tie−down hooks, the third seat must
be folded down. (See “—Folding down
third seat” on page 47 in Section 1−3.)
275
2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)
NOTICE
Do not use the anchor brackets on
the second seat seatback instead of
the tie−down hooks.
’04 HIGHLANDER_U (L/O 0308)
Luggage cover
USING LUGGAGE COVER
To use the luggage cover:
1. Pull out the forward luggage cover
and hang the hooks to the hook
brackets on the second seat seatback.
2. Pull out the rear luggage cover and
secure it to the hook brackets.
CAUTION
Do not place anything on the luggage
cover. Such items may be thrown
about and possibly injure people in
the vehicle during sudden braking or
an accident.
Vehicles with the third seat—When using
the luggage cover, the third seat must be
folded down. (See “—Folding down third
seat” on page 47 in Section 1−3.)
276
2004 HIGHLANDER from Aug. ’03 Prod. (OM48478U)
Loading...