TOYOTA Camry 2012 User Manual

Page 1

TABLE OF CONTENTS

1
Before driving
2
When driving
Interior fea-
3
Maintenance
4
and care
When trouble
5
arises
Vehicle
6
specifications
Adjusting and operating features such as door locks, mirrors, and steering column.
Driving, stopping and safe-driving information.
Air conditioning and audio systems, as well as other in­terior features for a comfortable driving experience.
Cleaning and protecting your vehicle, performing do-it­yourself maintenance, and maintenance information.
What to do if the vehicle needs to be towed, gets a flat tire, or is involved in an accident.
Detailed vehicle information.
7
For owners
Index
Reporting safety defects for U.S. owners, and seat belt and SRS airbag instructions for Canadian owners
Alphabetical listing of information contained in this manual.
1
Page 2
For your information
Main Owner’s Manual
Please note that this manual covers all models and all equipment, including options. Therefore, you may find some explanations for equipment not installed on your vehicle.
All specifications provided in this manual are current at the time of printing. However, because of the Toyota policy of continual product improvement, we reserve the right to make changes at any time without notice.
Depending on specifications, the vehicle shown in the illustrations may differ from your vehicle in terms of equipment.
Noise from under vehicle after turning off the engine
Approximately five hours after the engine is turned off, you may hear sound coming from under the vehicle for several minutes. This is the sound of a fuel evaporation leakage check and, it does not indicate a malfunction.
Accessories, spare parts and modification of your Toyota
A wide variety of non-genuine spare parts and accessories for Toyota vehicles are currently available on the market. You should know that Toyota does not warrant these products and is not responsible for their performance, repair, or replacement, or for any damage they may cause to, or adverse effect they may have on, your Toyota vehicle.
This vehicle should not be modified with non-genuine Toyota products. Modification with non-genuine Toyota products could affect its performance, safety or durability, and may even violate governmental regulations. In addition, damage or performance problems resulting from the modification may not be covered under warranty.
19
Page 3
Installation of a mobile two-way radio system
The installation of a mobile two-way radio system in your vehicle could affect electronic systems such as:
Multiport fuel injection system /sequential multiport fuel injection system
Cruise control system
Anti-lock brake system
SRS airbag system
Seat belt pretensioner system
Be sure to check with your Toyota dealer for precautionary measures or spe­cial instructions regarding installation of a mobile two-way radio system.
20
Page 4
Vehicle data recordings
Your Toyota is equipped with several sophisticated computers that will record certain data, such as:
• Engine speed
• Accelerator status
• Brake status
• Vehicle speed
• Shift position The recorded data varies according to the vehicle grade level and options
with which it is equipped. Furthermore, these computers do not record con­versations, sounds or pictures.
Data usage Toyota may use the data recorded in these computers to diagnose malfunc-
tions, conduct research and development, and improve quality. Toyota will not disclose the recorded data to a third party except:
• With the consent of the vehicle owner or with the consent of the lessee if the vehicle is leased
• In response to an official request by the police, a court of law or a govern­ment agency
• For use by Toyota in a law suit
• For research purposes where the data is not tied to a specific vehicle or vehicle owner
Usage of data collected through Safety Connect (U.S.mainland only)
If your Toyota has Safety Connect and if you have subscribed to those ser­vices, please refer to the Safety Connect Telematics Subscription Service Agreement for information on data collected and its usage.
21
Page 5
Event data recorder
This vehicle is equipped with an event data recorder (EDR). The main pur­pose of an EDR is to record, in certain crash or near crash-like situations, such as an air bag deployment or hitting a road obstacle, data that will assist in understanding how a vehicle’s systems performed. The EDR is designed to record data related to vehicle dynamics and safety systems for a short period of time, typically 30 seconds or less.
The EDR in this vehicle is designed to record such data as:
• How various systems in your vehicle were operating;
• Whether or not the driver and passenger safety belts were buckled/fas­tened;
• How far (if at all) the driver was depressing the accelerator and/or brake pedal; and,
• How fast the vehicle was traveling.
These data can help provide a better understanding of the circumstances in which crashes and injuries occur.
NOTE: EDR data are recorded by your vehicle only if a non-trivial crash situ­ation occurs; no data are recorded by the EDR under normal driving condi­tions and no personal data (e.g., name, gender, age, and crash location) are recorded. However, other parties, such as law enforcement, could combine the EDR data with the type of personally identifying data routinely acquired during a crash investigation. To read data recorded by an EDR, special equipment is required, and access to the vehicle or the EDR is needed. In addition to the vehicle manufacturer, other parties, such as law enforcement, that have the special equipment, can read the information if they have access to the vehicle or the EDR.
22
Page 6
Disclosure of the EDR data Toyota will not disclose the data recorded in an EDR to a third party except
when:
• An agreement from the vehicle’s owner (or the lessee for a leased vehicle)
is obtained
• In response to an official request by the police, a court of law or a govern-
ment agency
• For use by Toyota in a law suit However, if necessary, Toyota may:
• Use the data for research on vehicle safety performance
• Disclose the data to a third party for research purposes without disclosing
information about the specific vehicle or vehicle owner
Scrapping of your Toyota
The SRS airbag and seat belt pretensioner devices in your Toyota contain explosive chemicals. If the vehicle is scrapped with the airbags and seat belt pretensioners left as they are, this may cause an accident such as fire. Be sure to have the systems of the SRS airbag and seat belt pretensioner removed and disposed of by a qualified service shop or by your Toyota dealer before you scrap your vehicle.
Perchlorate Material
Special handling may apply, See www.dtsc.ca.gov/haza rdouswaste/perchlorate. Your vehicle has components that may contain perchlorate. These compo-
nents may include airbag, seat belt pretensioners, and wireless remote con­trol batteries.
23
Page 7
CAUTION
General precautions while driving
Driving under the influence: Never drive your vehicle when under the influ­ence of alcohol or drugs that have impaired your ability to operate your vehi­cle. Alcohol and certain drugs delay reaction time, impair judgment and reduce coordination, which could lead to an accident that could result in death or serious injury.
Defensive driving: Always drive defensively. Anticipate mistakes that other drivers or pedestrians might make and be ready to avoid accidents.
Driver distraction: Always give your full attention to driving. Anything that dis­tracts the driver, such as adjusting controls, talking on a cellular phone or reading can result in a collision with resulting death or serious injury to you, your occupants or others.
General precaution regarding children’s safety
Never leave children unattended in the vehicle, and never allow children to have or use the key.
Children may be able to start the vehicle or shift the vehicle into neutral. There is also a danger that children may injure themselves by playing with the windows, the moon roof, or other features of the vehicle. In addition, heat build-up or extremely cold temperatures inside the vehicle can be fatal to children.
24
Page 8
Symbols used throughout this manual
Cautions & Notices
CAUTION
This is a warning against something which, if ignored, may cause death or serious injury to people. You are informed about what you must or must not do in order to reduce the risk of death or serious injury to yourself and others.
NOTICE
This is a warning against something which, if ignored, may cause damage to the vehicle or its equipment. You are informed about what you must or must not do in order to avoid or reduce the risk of damage to your Toy ota and its equipment.
Symbols used in illustrations
Safety symbol
The symbol of a circle with a slash through it means “Do not”, “Do not do this”, or “Do not let this happen”.
Arrows indicating operations
Indicates the action (pushing, turning, etc.) used to operate switches and other devices.
Indicates the outcome of an operation (e.g. a lid opens).
25
Page 9
26
Page 10

Abbreviation list

Abbreviation/Acronym list
ABBREVIATIONS MEANING
A/C Air Conditioning ABS Anti-lock Brake System ACC Accessory
AI-SHIFT Artificial Intelligence Shift control
ALR Automatic Locking Retractor
BSM Blind Spot Monitor CRS Child Restraint System ECO Economy/Ecology ECU Electronic Control Unit EDR Event data recorder
ELR Emergency Locking Retractor EPS Electric Power Steering
GAWR Gross Axle Weight Ratings
516
GVWR Gross Vehicle Weight Rating
Page 11
ABBREVIATIONS MEANING
I/M Emission inspection and maintenance
LATCH Lower Anchors and Tethers for Children
LED Light Emitting Diode
M + S Mud and Snow
MMT Methylcyclopentadienyl Manganese Tricarbonyl
MTBE Methyl Tertiary Butyl Ether
OBD On Board Diagnostics
SRS Supplemental Restraint System
TIN Tire Identification Number TPMS Tire Pressure Warning System TRAC Traction Control
VIN Vehicle Identification Number
VSC Vehicle Stability Control
Abbreviation list
517
Page 12

1-1. Key information

Keys
The following keys are provided with the vehicle.
Vehicles without a smart key system (type A)
Master keys Valet key Key number plate
Vehicles without a smart key system (type B)
Master keys
Operating the wireless remote control function (P. 46)
Valet key Key number plate
Vehicles without a smart key system (type C)
Master keys
Operating the wireless remote control function (P. 46)
Valet key Key number plate
28
Page 13
1-1. Key information
Vehicles with a smart key system
Electronic keys
• Operating the smart key system (P. 32)
• Operating the wireless remote control function (P. 46)
Mechanical keys Key number plate
Using the mechanical key (vehicles with a smart key system)
To take out the mechanical key, push the release button and take the key out.
1
Before driving
The mechanical key can only be inserted in one direction, as the key only has grooves on one side. If the key cannot be inserted in a lock cylinder, turn it over and re-attempt to insert it.
After using the mechanical key, store it in the electronic key. Carry the mechanical key together with the electronic key. If the electronic key battery is depleted or the entry function does not operate properly, you will need the mechanical key. (→P. 451)
29
Page 14
1-1. Key information
When required to leave the vehicle’s key with a parking attendant
Lock the glove box as circumstances demand. (P. 290) Vehicles without a smart key system: Carry the master key for your own use
and provide the attendant with the valet key. Vehicles with a smart key system: Remove the mechanical key for your own
use and provide the attendant with the electronic key only.
Key number plate
Keep the plate in a safe place such as your wallet, not in the vehicle. In the event that a key (without a smart key system) or mechanical key (with a smart key system) is lost, a new key can be made by your Toyota dealer using the key number plate. (P. 450)
When riding in an aircraft (vehicles with a wireless remote control)
When bringing a key with wireless remote control function onto an aircraft, make sure you do not press any buttons on the key while inside the aircraft cabin. If you are carrying the key in your bag etc., ensure that the buttons are not likely to be pressed accidentally. Pressing a button may cause the key to emit radio waves that could interfere with the operation of the aircraft.
30
Page 15
1-1. Key information
NOTICE
To prevent key damage
Observe the following:
Do not drop the keys, subject them to strong shocks or bend them.
Do not expose the keys to high temperatures for long periods of time.
Do not get the keys wet or wash them in an ultrasonic washer etc.
Do not attach metallic or magnetic materials to the keys or place the keys
close to such materials.
Do not disassemble the keys.
Do not attach a sticker or anything else to the surface of the key.
Do not place the keys near objects that produce magnetic fields, such as
TVs, audio systems and glass top ranges, or medical electrical equipment, such as low-frequency therapy equipment.
Carrying the electronic key on your person (vehicles with a smart key
system)
Carry the electronic key 3.9 in. (10 cm) or more away from electric appli­ances that are turned on. Radio waves emitted from electric appliances within 3.9 in. (10 cm) of the electronic key may interfere with the key , causing the key to not function properly.
In case of a smart key system malfunction or other key-related prob-
lems (vehicles with a smart key system)
Take your vehicle with all the electronic keys provided with your vehicle to your Toyota dealer.
When a vehicle key is lost (vehicles with a smart key system)
If the key remains lost, the risk of vehicle theft increases significantly. Visit your Toyota dealer immediately with all remaining electronic keys that was provided with your vehicle.
1
Before driving
31
Page 16

1-2. Opening, closing and locking the doors and trunk

Smart key system
The following operations can be performed simply by carrying the electronic key on your person, for example in your pocket. (The driver should always carry the electronic key.)
Electronic key
Electronic key Electronic key
Unlocks and locks the doors (P. 33) Unlocks the trunk (P. 33) Starts the engine (P. 148)
32
: If equipped
Page 17
1-2. Opening, closing and locking the doors and trunk
Unlocking and locking the doors (front door handles only)
Grip the driver’s door handle to unlock the door. Grip the passen­ger’s door handle to unlock all the doors.*
Make sure to touch the sensor on the back of the handle.
The doors cannot be unlocked for 3 seconds after the doors are locked.
*: The door unlock settings can be
changed. (P. 38)
Touch the lock sensor (the indentation on the side of the door handle) to lock the doors.
1
Before driving
Unlocking the trunk
Press the button to unlock the trunk.
33
Page 18
1-2. Opening, closing and locking the doors and trunk
Antenna location and effective range
Antenna location
Antennas outside the cabin Antenna outside the trunk Antenna inside the trunk Antennas inside the cabin
34
Page 19
1-2. Opening, closing and locking the doors and trunk
Effective range (areas within which the electronic key is
detected)
When locking or unlocking the doors
The system can be operated when the electronic key is within about 2.3 ft. (0.7 m) of either of the front outside door handles. (Only the doors detecting the key can be operated.)
When unlocking the trunk
The system can be operated when the electronic key is within about 2.3 ft. (0.7 m) of the trunk release button.
When starting the engine or changing “ENGINE START STOP” switch modes
1
Before driving
The system can be operated when the electronic key is inside the vehicle.
Operation signals
Doors: A buzzer sounds and the emergency flashers flash to indicate that the doors have been locked/unlocked. (Locked: Once; Unlocked: Twice)
Trunk: A buzzer sounds to indicate that the trunk has been unlocked.
35
Page 20
1-2. Opening, closing and locking the doors and trunk
When the door cannot be locked by the lock sensor
Use your palm to touch the lock sensor.
Alarms and warning indicators
A combination of exterior and interior alarms as well as warning lights are used to prevent theft of the vehicle and unforeseeable accidents resulting from erroneous operation. Take appropriate measures for the warning light that comes on. (P. 427)
The following table describes circumstances and correction procedures when only alarms are sounded.
Alarm Situation Correction procedure
Exterior alarm sounds once for 5 seconds
36
An attempt was made to lock the doors using the smart key system while the electronic key was still inside the vehicle.
The trunk was closed while the electronic key was still inside the trunk and all the doors were locked.
An attempt was made to lock the vehicle while a door was open.
Retrieve the elec­tronic key from the passenger compart­ment and lock the doors again.
Retrieve the elec­tronic key from the trunk and close the trunk lid.
Close all of the doors and lock the doors again.
Page 21
1-2. Opening, closing and locking the doors and trunk
Alarm Situation Correction procedure
An attempt was made to
Interior alarm pings once and exterior alarm sounds once for 5 seconds
lock either front door by opening a door and putting the inside lock button into the lock position, then closing the door with the electronic key still inside
Retrieve the elec­tronic key from the vehicle and lock the doors again.
the vehicle. The “ENGINE START
STOP” switch was turned
Interior alarm sounds continu­ously
to ACCESSORY mode while the driver's door was open (The driver's door was opened when the “ENGINE START STOP” switch was in ACCES­SORY mode.)
Turn the “ENGINE START STOP” switch off and close the driver’s door.
The driver’s door was opened while any shift position other than P was selected without turning off
Shift the shift lever to
P. the “ENGINE START STOP” switch.
1
Before driving
Security feature
If a door is not opened within approximately 60 seconds after the vehicle is unlocked, the security feature automatically locks the vehicle again. (How­ever, depending on the location of the electronic key, the key may be detected as being in the vehicle. In this case, vehicle may be unlocked.)
37
Page 22
1-2. Opening, closing and locking the doors and trunk
Switching the door unlock function
It is possible to set which doors the entry function unlocks using the wireless remote control.
STEP
1
Turn the “ENGINE START STOP” switch off.
STEP
2
When the indicator light on the key surface is not on, press and hold , , or for about 5 seconds while pressing and
holding .
The setting changes each time an operation is performed, as shown below. (When changing the setting continuously, release the buttons, wait for at least 5 seconds, and repeat step 2.)
Unlocking doors Beep
Holding the driver's door handle unlocks only the driver's door.
Holding the front passenger’s door
Exterior: Beeps 3 times Interior: Beeps once
handle unlocks all the doors. Holding either front door handle
unlocks all the doors.
Exterior: Beeps twice Interior: Beeps once
Vehicles with an alarm system: To prevent unintended triggering of the alarm, unlock the doors using the wireless remote control and open and close a door once after the settings have been changed. (If a door is not opened within 60 seconds after is pressed, the doors will be locked again and the alarm will automatically be set.) In case that the alarm is triggered, immediately stop the alarm. (P. 95)
38
Page 23
1-2. Opening, closing and locking the doors and trunk
Battery-saving function
The battery-saving function will be activated in order to prevent the elec­tronic key battery and the vehicle battery from being discharged while the vehicle is not in operation for a long time.
In the following situations, the smart key system may take some time to
unlock the doors.
• The electronic key has been left in an area of approximately 6 ft. (2 m) of the outside of the vehicle for 10 minutes or longer.
• The smart key system has not been used for 5 days or longer.
If the smart key system has not been used for 14 days or longer, the
doors cannot be unlocked at any doors except the driver’s door. In this case, take hold of the driver’s door handle, or use the wireless remote control or the mechanical key, to unlock the doors.
Electronic key battery-saving function
When battery-saving mode is set, battery depletion is minimized by stopping the electronic key from receiving radio waves.
Press twice while pressing and holding . Confirm that the electronic
key indicator flashes 4 times. While the battery-saving mode is set, the
smart key system cannot be used. To cancel the function, press any of the elec­tronic key buttons.
1
Before driving
39
Page 24
1-2. Opening, closing and locking the doors and trunk
Conditions affecting operation
The smart key system uses weak radio waves. In the following situations, the communication between the electronic key and the vehicle may be affected, preventing the smart key system, wireless remote control and engine immobilizer system from operating properly. (Ways of coping: P. 451)
When the electronic key battery is depleted
Near a TV tower, electric power plant, gas station, radio st ation, large dis-
play, airport or other facility that generates strong radio waves or electri­cal noise
When the electronic key is in contact with, or is covered by the following
metallic objects
• Cards to which aluminum foil is attached
• Cigarette boxes that have aluminum foil inside
• Metallic wallets or bags
• Coins
• Hand warmers made of metal
• Media such as CDs and DVDs
When other wireless key (that emit radio waves) is being used nearby
When carrying the electronic key together with the following devices that
emit radio waves
• A portable radio, cellular phone, cordless phone or other wireless com­munication device
• Another vehicle’s electronic key or a wireless key that emits radio waves
• Personal computers or personal digital assistants (PDAs)
• Digital audio players
• Portable game systems
If window tint with a metallic content or metallic objects are attached to
the rear window
When the electronic key is placed near a battery charger or electronic
devices
40
Page 25
1-2. Opening, closing and locking the doors and trunk
Notes for the entry function
Even when the electronic key is within the effective range (detection
areas), the system may not operate properly in the following cases:
• The electronic key is too close to the window or outside door handle, near the ground, or in a high place when the doors are locked or unlocked.
• The electronic key is near the ground or in a high place, or too close to the rear bumper center when the trunk is unlocked.
• The electronic key is on the instrument panel, rear package tray or floor, in the door pockets or glove box, or near a vent when the engine is started or “ENGINE START STOP” switch modes are changed.
Do not leave the electronic key on top of the instrument panel or near the
door pockets or a vent when exiting the vehicle. Depending on the radio wave reception conditions, it may be detected by the antenna outside the cabin and the door will become lockable from the outside, possibly trap­ping the electronic key inside the vehicle.
As long as the electronic key is within the effective range, the doors may
be locked or unlocked by anyone.
Even if the electronic key is not inside the vehicle, it may be possible to
start the engine if the electronic key is near the window.
The doors may unlock if a large amount of water splashes on the door
handle, such as in the rain or in a car wash when the electronic key is within the effective range. (The door will automatically be locked after approximately 60 seconds if the doors are not opened and closed.)
Gripping the door handle when wearing a glove may not unlock the door.
If the wireless remote control is used to lock the doors when the elec-
tronic key is near the vehicle, there is a possibility that the door may not be unlocked by the entry function. (Use the wireless remote control to unlock the doors.)
A sudden approach to the effective range or door handle may prevent the
doors from being unlocked. In this case, return the door handle to the original position and check that the doors unlock before pulling the door handle again.
1
Before driving
41
Page 26
1-2. Opening, closing and locking the doors and trunk
Notes for locking the doors
Touching the door lock sensor while wearing gloves may delay or prevent
lock operation. Remove the gloves and touch the lock sensor again.
When the lock operation is performed using the lock sensor, recognition
signals will be shown up to two consecutive times. After this, no recogni­tion signals will be given.
If the door handle becomes wet while the electronic key is within the
effective range, the door may lock and unlock repeatedly. In that case, follow the following correction procedures to wash the vehicle:
• Place the electronic key in a location 6 ft. (2 m) or more away from the vehicle. (Take care to ensure that the key is not stolen.)
• Set the electronic key to battery-saving mode to disable the smart key system. (P. 39)
If the electronic key is inside the vehicle and a door handle becomes wet
during a car wash, a buzzer will sound outside the vehicle. To turn off the alarm, lock all the doors.
The lock sensor may not work properly if it comes into contact with ice,
snow, mud, etc. Clean the lock sensor and attempt to operate it again.
Notes for the unlocking function
A sudden approach to the effective range or door handle may prevent the
doors from being unlocked. In this case, return the door handle to the original position and check that the doors unlock before pulling the door handle again.
Gripping the door handle when wearing a glove may not unlock the door.
Remove the gloves and touch the sensor on the back of the handle again.
If the door handle becomes wet while the electronic key is within the
effective range, the door may lock and unlock repeatedly. In that case, follow the following correction procedures to wash the vehicle:
• Place the electronic key in a location 6 ft. (2 m) or more away from the vehicle. (Take care to ensure that the key is not stolen.)
• Set the electronic key to battery-saving mode to disable the smart key system. (P. 39)
If there is another electronic key in the detection area, it may take slightly
longer to unlock the doors after the door handle is gripped.
42
Page 27
1-2. Opening, closing and locking the doors and trunk
When the vehicle is not driven for extended periods
To prevent theft of the vehicle, do not leave the electronic key within 6 ft.
(2 m) of the vehicle.
The smart key system can be deactivated in advance. (P. 493)
Alarm (if equipped)
Using the smart key system to lock the doors will set the alarm system. (P. 95)
To operate the system properly
Make sure to carry the electronic key when operating the system. Do not get the electronic key too close to the vehicle when operating the system from the outside of the vehicle.
Depending on the position and holding condition of the electronic key, the key may not be detected correctly and the system may not operate properly. (The alarm may go off accidentally, or the door lock prevention function may not operate.)
If the smart key system does not operate properly
Locking and unlocking the doors: Use the mechanical key. (P. 451)
Starting the engine:P. 451
1
Before driving
43
Page 28
1-2. Opening, closing and locking the doors and trunk
Electronic key battery depletion
The standard battery life is 1 to 2 years.
If the battery becomes low, an alarm will sound in the cabin when the
engine stops. (P. 427)
As the electronic key always receives radio waves, the battery will
become depleted even if the electronic key is not used. The following symptoms indicate that the electronic key battery may be depleted. Replace the battery when necessary. (P. 386)
• The smart key system or the wireless remote control does not operate.
• The detection area becomes smaller.
• The LED indicator on the key surface does not turn on.
To avoid serious deterioration, do not leave the electronic key within 3 ft.
(1 m) of the following electrical appliances that produce a magnetic field:
•TVs
• Personal computers
• Cellular phones, cordless phones and battery chargers
• Recharging cellular phones or cordless phones
• Glass top ranges
• Table lamps
When the electronic key battery is fully depleted
P. 386
If the smart key system has been deactivated in a customized setting
Locking and unlocking the doors: Use the wireless remote control or
mechanical key. (P. 46, 451)
Starting the engine and changing “ENGINE START STOP” switch
modes: P. 452
Stopping the engine: P. 149
Customization that can be configured at Toyota dealer
Settings (e. g. smart key system) can be changed. (Customizable features: P. 493)
44
Page 29
1-2. Opening, closing and locking the doors and trunk
Certification for the smart key system
U.S.A.
FCC ID: NI4TMLF10-4 FCC ID: NI4TMLF10-5 FCC ID: HYQ23AAB FCC ID: HYQ14FBA NOTE:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interfer­ence, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Canada
NOTE: Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, includ­ing interference that may cause undesired operation of the device.
1
Before driving
CAUTION
Caution regarding interference with electronic devices
People with implanted pacemakers or cardiac defibrillators should keep
away from the smart key system antennas. (P. 34) The radio waves may affect the operation of such devices. If necessary, the entry function can be disabled. Ask your Toyota dealer for details, such as the frequency of radio waves and timing of emitting the radio waves. Then, consult your doctor to see if you should disable the entry function.
Users of any electrical medical device other than implanted pacemakers
and implanted cardiac defibrillators should consult the manufacturer of the device for information about its operation under the influence of radio waves. Radio waves could have unexpected effects on the operation of such medical devices.
Ask your Toyota dealer for details for disabling the entry function.
45
Page 30
1-2. Opening, closing and locking the doors and trunk
Wireless remote control
The wireless remote control can be used to lock and unlock the vehi­cle.
Vehicles without a smart key system (type A)
Locks all the doors Sounds the alarm
(press and hold) Unlocks all the doors
Pressing the button unlocks the driver’s door. Pressing the button again within 5 seconds unlocks the other doors.
Opens the driver’s window and moon roof (press and hold)
*
Unlocks the trunk (press and hold)
46
*: This setting must be custom-
ized at your Toyota dealer.
: If equipped
Page 31
1-2. Opening, closing and locking the doors and trunk
Vehicles without a smart key system (type B)
Locks all the doors Unlocks all the doors
Pressing the button unlocks the driver’s door. Pressing the button again within 5 seconds unlocks the other doors.
Opens the driver’s window and moon roof (press and hold)
*
Sounds the alarm (press and hold)
Unlocks the trunk (press and hold)
*: This setting must be custom-
ized at your Toyota dealer.
1
Before driving
Vehicles with a smart key system
Locks all the doors Unlocks all the doors
Pressing the button unlocks the driver’s door. Pressing the button again within 5 seconds unlocks the other doors.
Opens the driver’s window and moon roof (press and hold)
*
Unlocks the trunk (press and hold)
Sounds the alarm (press and hold)
*: This setting must be custom-
ized at your Toyota dealer.
47
Page 32
1-2. Opening, closing and locking the doors and trunk
Operation signals
Doors: A buzzer sounds and the emergency flashers flash to indicate that
the doors have been locked/unlocked.
(Locked: Once; Unlocked: Twice) Trunk: A buzzer sounds to indicate that the trunk has been unlocked. Driver’s window and moon roof: A buzzer sounds to indicate that the driver’s
window and moon roof are opening.
Door lock buzzer
If an attempt to lock the doors is made when a door is not fully closed, a buzzer sounds continuously . Fully close the door to stop the bu zzer, and lock the vehicle once more.
Panic mode
Vehicles without a smart key system
When is pressed for longer than about one second, an alarm will
sound intermittently and the vehicle lights will flash to deter any person from trying to break into or damage your vehicle.
To stop the alarm, press any button on the wireless remote control.
48
Page 33
1-2. Opening, closing and locking the doors and trunk
Vehicles with a smart key system
When is pressed for longer than about one second, an alarm will
sound intermittently and the vehicle lights will flash to deter any person from trying to break into or damage your vehicle.
To stop the alarm, press any button on the electronic key.
Security feature
If a door is not opened within approximately 60 seconds after the vehicle is unlocked, the security feature automatically locks the vehicle again.
Alarm (if equipped)
Using the wireless remote control to lock the doors will set the alarm system. (P. 95)
1
Before driving
49
Page 34
1-2. Opening, closing and locking the doors and trunk
Conditions affecting operation
Vehicles without a smart key system
The wireless remote control function may not operate normally in the follow­ing situations:
When the wireless key battery is depleted
Near a TV tower, electric power plant, gas station, radio st ation, large dis-
play, airport or other facility that generates strong radio waves or electri­cal noise
When carrying a portable radio, cellular phone or other wireless commu-
nication devices
When the wireless key is in contact with, or is covered by a metallic
object
When other wireless key (that emit radio waves) is being used nearby
If window tint with a metallic content or metallic objects are attached to
the rear window
Vehicles with a smart key system
P. 40
If the wireless remote control does not operate properly (vehicles with
a smart key system)
Locking and unlocking the doors: Use the mechanical key. (P. 451)
Key battery depletion
Vehicles without a smart key system
If the wireless remote control function does not operate, the battery may be depleted. Replace the battery when necessary. (P. 384)
Vehicles with a smart key system
P. 44
When the key battery is fully depleted
P. 384
Confirmation of the registered key number (vehicles with a smart key
system)
The number of keys already registered to the vehicle can be confirmed. Ask your Toyota dealer for details.
50
Page 35
1-2. Opening, closing and locking the doors and trunk
Customization that can be configured at Toyota dealer
Settings (e.g. wireless remote control system) can be changed. (Customizable features: P. 493)
Certification for wireless remote control
U.S.A. (vehicles without a smart key system)
FCC ID: HYQ23AAC FCC ID: HYQ12BDM NOTE:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interfer­ence, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
U.S.A. (vehicles with a smart key system)
FCC ID: NI4TMLF10-4 FCC ID: NI4TMLF10-5 FCC ID: HYQ23AAB FCC ID: HYQ14FBA NOTE:
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interfer­ence, and (2) this device must accept any interference received, including interference that may cause undesired operation.
FCC WARNING: Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Canada
NOTE: Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, includ­ing interference that may cause undesired operation of the device.
1
Before driving
51
Page 36
1-2. Opening, closing and locking the doors and trunk
Doors
The vehicle can be locked and unlocked using the entry function, wireless remote control, key or door lock switch.
Entry function (vehicles with a smart key system)
P. 32
Wireless remote control (if equipped)
P. 46
Key
Turning the key operates the doors as follows:
Vehicles without a smart key system
Locks all the doors Unlocks all the doors
Driver’s side only: Turning the key unlocks the driver's door. Turning the key again unlocks the other doors.
Vehicles with a smart key system
The doors can also be locked and unlocked with the mechanical key. (P. 451)
Door lock switch
Locks all the doors Unlocks all the doors
52
Page 37
1-2. Opening, closing and locking the doors and trunk
Inside lock button
Unlocks the door Locks the door
The front doors can be opened by pulling the inside handle even if the lock buttons are in the lock position.
Locking the doors from the outside without a key
STEP
1
Move the inside lock button to the lock position.
STEP
2
Close the door.
Vehicles without a smart key system
The door cannot be locked if either of the front doors is open and the key is in the engine switch.
1
Before driving
Vehicles with a smart key system
The door cannot be locked if the “ENGINE START STOP” switch is in ACCESSORY or IGNITION ON mode, or the electronic key is left inside the vehicle.
The key may not be detected correctly and the door may be locked.
53
Page 38
1-2. Opening, closing and locking the doors and trunk
Rear door child-protector lock
The door cannot be opened from inside the vehicle when the lock is set.
Unlock Lock
These locks can be set to prevent children from opening the rear doors. Push down on each rear door switch to lock both rear doors.
54
Page 39
1-2. Opening, closing and locking the doors and trunk
Automatic door locking and unlocking systems
The following functions can be set or cancelled:
Function Operation
Shift position linked door locking function
Shift position linked door unlocking function
Speed linked door lock­ing function
Driver's door linked door unlocking function (vehicles without a smart key system)
Driver's door linked door unlocking function (vehicles with a smart key system)
Shifting the shift lever out of P locks all the doors.
Shifting the shift lever to P unlocks all the doors.
All the doors are locked when the vehicle speed is approximately 12 mph (20 km/h) or higher.
All the doors are unlocked when the driver's door is opened within 10 seconds after turn­ing the engine switch to “ACC” or “LOCK”.
All the doors are unlocked when the driver's door is opened within 10 seconds after turn­ing the “ENGINE START STOP” switch off.
Setting and canceling the functions (vehicles without naviga-
tion system and Display Audio system)
To switch between setting and canceling, follow the procedure below.
1
Before driving
STEP
1
Vehicles without a smart key system
Close all the doors and turn the engine switch to the “ON” position. (Perform step 2 within 10 seconds.)
Vehicles with a smart key system
Close all the doors and turn the “ENGINE START STOP” switch to IGNITION ON mode. (Perform step 2 within 10 sec­onds.)
55
Page 40
1-2. Opening, closing and locking the doors and trunk
STEP
2
Function
Shift position linked door lock­ing function
Shift position linked door unlocking function
Speed linked door lo cking func­tion
Driver's door linked door unlock­ing function
Shift the shift lever to P or N, and press and hold the driver's door lock switch (
or ) for
approximately 5 seconds and then release.
The shift lever and switch posi­tions corresponding to the desired function to be set are shown in the following table.
Use the same procedure to can­cel the function.
Shift lever
position
P
N
Driver’s door lock
switch position
When the setting or canceling operation is complete, all doors are locked and then unlocked.
56
Page 41
1-2. Opening, closing and locking the doors and trunk
If a wrong key is used (vehicles with a smart key system)
The key cylinder rotates freely to isolate inside mechanism.
If the smart key system has been deactivated in a customized setting
(vehicles with a smart key system)
Use the wireless remote control or mechanical key. (P. 46, 451)
Customization that can be configured at Toyota dealer
Settings (e.g. unlocking function using a key) can be changed. (Customizable features P. 493)
CAUTION
To prevent an accident
Observe the following precautions while driving the vehicle. Failure to do so may result in a door opening and an occupant falling out, resulting in death or serious injury.
Always use a seat belt.
Always lock all the doors.
Ensure that all doors are properly closed.
Do not pull the inside handle of the doors while driving.
The doors may be opened and the passengers are thrown out of the vehi­cle and it may result in serious injury or death.
Be especially careful for the front doors, as the doors may be opened even if the inside lock buttons are in locked position.
Set the rear door child-protector locks when children are seated in the rear
seats.
1
Before driving
57
Page 42
1-2. Opening, closing and locking the doors and trunk
Trunk
The trunk can be opened using the key, trunk opener, entry function or wireless remote control.
Opening the trunk from inside the vehicle
Pull up the lever to release the trunk lid.
Opening the trunk from outside the vehicle
Key (vehicles without a wireless remote control)
Turn the master key clockwise to release the trunk lid.
Entry function (vehicles with a smart key system)
P. 32
Wireless remote control (if equipped)
P. 46
58
Page 43
1-2. Opening, closing and locking the doors and trunk
Trunk light
The trunk light turns on when the trunk is opened.
Function to prevent the trunk being locked with the electronic key
inside (vehicles with a smart key system)
When all doors are being locked, closing the trunk lid with the electronic
key left inside the trunk will sound an alarm. In this case, the trunk lid can be opened using the entry function.
Even when the spare electronic key is put in the trunk with all the doors
locked, the key confinement prevention function can be activated so the trunk can be opened. In order to prevent theft, take all electronic keys with you when leaving the vehicle.
Even when the electronic key is put in the trunk with all the doors are
locked, the key may not be detected depending on the places and the surrounding radio wave conditions. In this case, the key confinement pre­vention function cannot be activated, causing the doors to lock when the trunk is closed. Make sure to check where the key is before closing the trunk.
The key confinement prevention function cannot be activated if any one
of the doors is unlocked. In this case, open the trunk using the trunk opener.
Internal trunk release lever
1
Before driving
The trunk lid can be opened by pulling up the glow-in-the-dark lever located on the inside of the trunk lid.
The lever will continue to glow for some time after the trunk lid is closed.
59
Page 44
1-2. Opening, closing and locking the doors and trunk
CAUTION
Caution while driving
Keep the trunk lid closed while driving.
If the trunk lid is left open, it may hit near-by objects while driving or lug­gage in the trunk may be unexpectedly thrown out, causing an accident. In addition, exhaust gases may enter the vehicle, causing death or a seri­ous health hazard. Make sure to close the trunk lid before driving.
Before driving the vehicle, make sure that the trunk lid is fully closed. If the
trunk lid is not fully closed, it may open unexpectedly while driving, caus­ing an accident.
Never let anyone sit in the trunk. In the event of sudden braking or a colli-
sion, they are susceptible to death or serious injury.
When children are in the vehicle
Observe the following precautions. Failure to do so may result in death or serious injury.
Do not allow children to enter the trunk.
If a child is accidentally locked in the trunk, they could overheat or suffo­cate.
Do not allow a child to open or close the trunk lid.
Doing so may cause the trunk lid to operate unexpectedly, or cause the child’s hands, head, or neck to be caught by the closing trunk lid.
60
Page 45
1-2. Opening, closing and locking the doors and trunk
CAUTION
Using the trunk
Observe the following precautions. Failure to do so may cause parts of the body to be caught, resulting in seri­ous injury.
Remove any heavy loads, such as snow and ice, from the trunk lid before
opening it. Failure to do so may cause the trunk lid to fall closed again after it is opened.
When opening or closing the trunk lid, thoroughly check to make sure the
surrounding area is safe.
If anyone is in the vicinity, make sure they are safe and let them know that
the trunk is about to open or close.
Use caution when opening or closing the trunk lid in windy weather as it
may move abruptly in strong wind.
The trunk lid may fall if it is not opened
fully. It is more difficult to open or close the trunk lid on an incline than on a level surface, so beware of the trunk lid unexpectedly opening or closing by itself. Make sure that the trunk lid is fully open and secure before using the trunk.
When closing the trunk lid, take extra
care to prevent your fingers etc. from being caught.
When closing the trunk lid, make sure
to press it lightly on its outer surface.
1
Before driving
Do not attach any accessories other than genuine Toyota parts to the trunk
lid. Such additional weight on the trunk lid may cause the lid to fall closed again after it is opened.
61
Page 46
1-2. Opening, closing and locking the doors and trunk
62
Page 47
1-2. Opening, closing and locking the doors and trunk
1
Before driving
63
Page 48
1-3. Adjustable components (seats, mirrors, steering wheel)
Front seats
Manual seat
Seat position adjustment lever
Seatback angle adjustment lever
Vertical height adjustment lever (driver’s side only)
62
Page 49
Power seat
1-3. Adjustable components (seats, mirrors, steering wheel)
1
Before driving
Seat position adjustment switch Seatback angle adjustment switch Seat cushion (front) angle adjustment switch (driver’s side only) Vertical height adjustment switch (driver’s side only) Lumbar support adjustment switch (driver’s side only)
63
Page 50
1-3. Adjustable components (seats, mirrors, steering wheel)
CAUTION
Seat adjustment
To reduce the risk of s liding under the lap belt during a collision, do not
recline the seat more than necessary. If the seat is too reclined, the lap belt may slide past the hips and apply restraint forces directly to the abdomen, or your neck may contact the shoulder belt, increasing the risk of death or serious injury in the event of an accident. Adjustments should not be made while driving as the seat may unexpect­edly move and cause the driver to lose control of the vehicle.
Manual seat only: After adjusting the seat, make sure that the seat is
locked in position.
64
Page 51
1-3. Adjustable components (seats, mirrors, steering wheel)
Rear seats
The seatbacks of the rear seats can be folded down.
Folding down the rear seatbacks
Pull the seatback lever in the trunk for the seatback you wish to fold down.
CAUTION
When folding the rear seatbacks down
Observe the following precautions. Failure to do so may result in death or serious injury.
Do not fold the seatbacks down while driving.
Stop the vehicle on level ground, set the parking brake and shift the shift
lever to P.
Do not allow anyone to sit on a folded seatback or in the trunk while driv-
ing.
Do not allow children to enter the trunk.
1
Before driving
65
Page 52
1-3. Adjustable components (seats, mirrors, steering wheel)
CAUTION
When returning the seat to its original position
Ensure that the seat belt does not get caught between or behind the seats.
If the seat belt has been released from its guide, pass the seat belt through
its guide. (P. 72)
Seat adjustment
Be careful not to get hands or feet pinched between the rear console box and the rear seat when folding down the rear seatback.
After returning the seatback to the upright position
Observe the following precautions. Failure to do so may result in death or serious injury.
Make sure the seatback is securely locked by pressing it forward and rear-
ward on the top.
Check that the seat belts are not twisted or caught in the seatback.
Make sure that the seat belt is passing through its guide.
NOTICE
When left seatback is folded down
Make sure the luggage loaded in the enlarged trunk will not damage the webbing of the rear center seat belt.
66
Page 53
1-3. Adjustable components (seats, mirrors, steering wheel)
Head restraints
Head restraints are provided for all seats.
Vertical adjustment (front seats)
Up
Pull the head restraints up.
Down
Lock release button
Removing the head restraints (front seats)
Pull the head restraint up while pressing the lock release button.
Push the head restraint down while pushing the lock release button.
1
Before driving
Installing the head restraints (front seats)
Align the head restraint with the installa­tion holes and push it down to the lock position.
Press and hold the lock release button when lowering the head restraint.
67
Page 54
1-3. Adjustable components (seats, mirrors, steering wheel)
Adjusting the height of the head restraints (front seats)
Make sure that the head restraints are adjusted so that the center of the head restraint is closest to the top of your ears.
CAUTION
Head restraint precautions (front seats)
Observe the following precautions regarding the head restraints. Failure to do so may result in death or serious injury.
Use the head restraints designed for each respective seat.
Adjust the head restraints to the correct position at all times.
After adjusting the head restraints, push down on them and make sure
they are locked in position.
Do not drive with the head restraints removed.
68
Page 55
1-3. Adjustable components (seats, mirrors, steering wheel)
Seat belts
Make sure that all occupants are wearing their seat belts before driv­ing the vehicle.
Correct use of the seat belts
Extend the shoulder belt so
that it comes fully over the shoulder, but does not come into contact with the neck or slide off the shoul­der.
Position the lap belt as low as possible over the hips.
Adjust the position of the seatback. Sit up straight and well back in the seat.
Do not twist the seat belt.
1
Before driving
Fastening and releasing the seat belt
To fasten the seat belt, push the plate into the buckle until a click sound is heard.
To release the seat belt, press the release button.
Release button
69
Page 56
1-3. Adjustable components (seats, mirrors, steering wheel)
Adjusting the seat belt shoulder anchor height (front seats)
Push the seat belt shoulder anchor down while pressing the release button.
Push the seat belt shoulder anchor up.
Move the height adjuster up and down as needed until you hear a click.
Seat belt pretensioners (front seats)
The pretensioner helps the seat belt to quickly restrain the occu­pant by retracting the seat belt when the vehicle is subjected to certain types of severe frontal or side collision.
70
The pretensioner may not acti­vate in the event of a minor frontal impact, a minor side impact, a rear impact or a vehicle rollover.
Page 57
1-3. Adjustable components (seats, mirrors, steering wheel)
Emergency locking retractor (ELR)
The retractor will lock the belt during a sudden stop or on impact. It may also lock if you lean forward too quickly. A slow, easy motion will allow the belt to extend so that you can move around fully.
Automatic locking retractor (ALR)
When a passenger's shoulder belt is completely extended and then retracted even slightly, the belt is locked in that position and cannot be extended. This feature is used to hold the child restraint system (CRS) firmly . To free the belt again, fully retract the belt and then pull the belt out once more. (P. 122)
Pregnant women
Obtain medical advice and wear the seat belt in the proper way. (P. 69)
Women who are pregnant should position the lap belt as low as possible over the hips in the same manner as other occu­pants. Extend the shoulder belt com­pletely over the shoulder and position the belt across the chest. Avoid belt contact over the rounding of the abdominal area.
If the seat belt is not worn properly, not only a pregnant woman, but also the fetus could suffer death or serious injury as a result of sudden braking or a collision.
1
Before driving
People suffering illness
Obtain medical advice and wear the seat belt in the proper way. (P. 69)
Child seat belt usage
The seat belts of your vehicle were principally designed for persons of adult size.
Use a child restraint system appropriate for the child, until the child
becomes large enough to properly wear the vehicle's seat belt. (P. 1 18)
When the child becomes large enough to properly wear the vehicle's seat
belt, follow the instructions on P. 69 regarding seat belt usage.
71
Page 58
1-3. Adjustable components (seats, mirrors, steering wheel)
Replacing the belt after the pretensioner has been activated
If the vehicle is involved in multiple collisions, the pretensioner will activate for the first collision, but will not activate for the second or subsequent colli­sions.
Seat belt extender
If your seat belts cannot be fastened securely because they are not long enough, a personalized seat belt extender is available from your Toyota dealer free of charge.
Rear seat belt
Use the seat belt after passing it through the guide if the seat belt comes free from the guide.
72
Page 59
1-3. Adjustable components (seats, mirrors, steering wheel)
CAUTION
Observe the following precautions to reduce the risk of injury in the event of sudden braking, sudden swerving or an accident. Failure to do so may cause death or severe injury.
Wearing a seat belt
Ensure that all passengers wear a seat belt.
Always wear a seat belt properly.
Each seat belt should be used by one person only. Do not use a seat belt
for more than one person at once, including children.
Toyota recommends that children be seated in the rear seat and always
use a seat belt and/or an appropriate child restraint system.
To achieve a proper seating position, do not recline the seat more than
necessary. The seat belt is most effective when the occupants are sitting up straight and well back in the seats.
Do not wear the shoulder belt under your arm.
Always wear your seat belt low and snug across your hips.
When children are in the vehicle
Do not allow children to play with the seat belt. If the seat belt becomes twisted around a child’s neck, it may lead to choking or other serious injuries that could result in death. If this occurs and the buckle cannot be unfastened, scissors should be used to cut the belt.
Seat belt pretensioners
Do not place anything, such as a cushion, on the front passenger's seat.
Doing so will disperse the passenger's weight, which prevents the sensor from detecting the passenger's weight properly. As a result, the seat belt pretensioner for the front passenger's seat may not activate in the event of a collision.
If the pretensioner has activated, the SRS warning light will come on. In
that case, the seat belt cannot be used again and must be replaced at your Toyota dealer.
1
Before driving
73
Page 60
1-3. Adjustable components (seats, mirrors, steering wheel)
CAUTION
Adjustable shoulder anchor
Always make sure the shoulder belt is positioned across the center of your shoulder. The belt should be kept away from your neck, but not falling off your shoulder. Failure to do so could reduce the amount of protection in an accident and cause death or serious injuries in the event of a sudden stop, sudden swerve or accident. (P. 70)
Seat belt damage and wear
Do not damage the seat belts by allowing the belt, plate, or buckle to be
jammed in the door.
Inspect the seat belt system periodically. Check for cuts, fraying, and loose
parts. Do not use a damaged seat belt until it is replaced. Damaged seat belts cannot protect an occupant from death or serious injury.
Ensure that the belt and plate are locked and the belt is not twisted.
If the seat belt does not function correctly, immediately contact your Toyota dealer.
Replace the seat assembly, including the belts, if your vehicle has been
involved in a serious accident, even if there is no obvious damage.
Do not attempt to install, remove, modify, disassemble or dispose of the
seat belts. Have any necessary repairs carried out by your Toyota dealer. Inappropriate handling of the pretensioner may prevent it from operating properly, resulting in death or serious injury.
Always make sure the shoulder belt passes through the guide when using
the seat belt. Failure to properly position the belt may reduce the amount of protection in an accident and could lead to death or serious injury in a collision or sudden stop.
Always make sure that the seat belt is not twisted, does not get caught in
the guide or the seatback and is arranged in the proper position.
74
Page 61
1-3. Adjustable components (seats, mirrors, steering wheel)
CAUTION
Using a seat belt extender
Do not wear the seat belt extender if you can fasten the seat belt without
the extender.
Do not use the seat belt extender when installing a child restraint system
because the belt will not securely hold the child restraint system, increas­ing the risk of death or serious injury in the event of an accident.
The personalized extender may not be safe on another vehicle, when
used by another person, or at a different seating position other than the one originally intended.
NOTICE
When using a seat belt extender
When releasing the seat belt, press on the buckle release button on the extender, not on the seat belt. This helps prevent damage to the vehicle interior and the extender itself.
1
Before driving
75
Page 62
1-3. Adjustable components (seats, mirrors, steering wheel)
Steering wheel
The steering wheel can be adjusted to a comfortable position.
STEP
1
Hold the steering wheel and push the lever down.
STEP
2
Adjust to the ideal position by moving the steering wheel horizontally and vertically.
After adjustment, pull the lever up to secure the steering wheel.
CAUTION
Caution while driving
Do not adjust the steering wheel while driving. Doing so may cause the driver to mishandle the vehicle and cause an acci­dent, resulting in death or serious injury.
After adjusting the steering wheel
Make sure that the steering wheel is securely locked. Otherwise, the steering wheel may move suddenly, possibly causing an accident, and resulting in death or serious injury.
76
Page 63
1-3. Adjustable components (seats, mirrors, steering wheel)
Anti-glare inside rear view mirror
Glare from the headlights of vehicles behind can be reduced by using the following functions:
Manual anti-glare inside rear view mirror
Normal position Anti-glare position
Auto anti-glare inside rear view mirror
In automatic mode, sensors are used to detect the headlights of vehicles behind and the reflected light is automatically reduced.
Turns automatic mode on/off
The indicator comes on when automatic mode is turned on.
Vehicles without a smart key system
The mirror will revert to the automatic mode each time the engine switch is turned to the “ON” position.
Vehicles with a smart key system
The mirror will revert to the automatic mode each time the “ENGINE START STOP” switch is turned to IGNITION ON mode.
1
Before driving
77
Page 64
1-3. Adjustable components (seats, mirrors, steering wheel)
Adjusting the height of rear view mirror
Adjust the height of the rear view mirror by moving it up and down.
To prevent sensor error (vehicles with auto anti-glare inside rear view
mirror)
To ensure that the sensors operate prop­erly, do not touch or cover them.
CAUTION
Caution while driving
Do not adjust the position of the mirror while driving. Doing so may lead to mishandling of the vehicle and an accident, resulting in death or serious injury.
78
Page 65
1-3. Adjustable components (seats, mirrors, steering wheel)
Outside rear view mirrors
Mirror angle can be adjusted using the switch.
STEP
1
STEP
2
Folding the mirrors
To select a mirror to adjust, press the switch.
Left Right
To adjust the mirror, press the switch.
Up Right Down Left
Push the mirror back in the direc­tion of the vehicle's rear.
1
Before driving
79
Page 66
1-3. Adjustable components (seats, mirrors, steering wheel)
Mirror angle can be adjusted when
Vehicles without a smart key system
The engine switch is in the “ACC” or “ON” position.
Vehicles with a smart key system
The “ENGINE START STOP” switch is in ACCESSORY or IGNITION ON mode.
When the mirrors are fogged up (vehicles with mirror defoggers)
Turn on the mirror defoggers to defog the mirrors. (P. 240)
CAUTION
When driving the vehicle
Observe the following precautions while driving. Failure to do so may result in loss of control of the vehicle and cause an accident, resulting in death or serious injury.
Do not adjust the mirrors while driving.
Do not drive with the mirrors folded.
Both the driver and passenger side mirrors must be extended and properly
adjusted before driving.
When a mirror is moving
To avoid personal injury and mirror malfunction, be careful not to get your hand caught by the moving mirror.
When the mirror defoggers are operating (vehicles with mirror defog-
gers)
Do not touch the rear view mirror surfaces, as they can become very hot and burn you.
80
Page 67

1-4. Opening and closing the windows and moon roof

Power windows
The power windows can be opened and closed using the switches.
Operating the switch moves the windows as follows:
Window lock switch
Closing One-touch closing (driver’s
window only) Opening One-touch opening (driver ’s
window only)
*
*
*:Pressing the switch in the
opposite direction will stop win­dow travel partway.
Press the switch down to lock the passenger window switches.
Use this switch to prevent chil­dren from accidentally opening or closing a passenger window.
1
Before driving
81
Page 68
1-4. Opening and closing the windows and moon roof
The power windows can be operated when
Vehicles without a smart key system
The engine switch is in the “ON” position.
Vehicles with a smart key system
The “ENGINE START STOP” switch is in IGNITION ON mode.
Operating the power windows after turning the engine off
Vehicles without a smart key system
The power windows can be operated for approximately 45 seconds even after the engine switch is turned to the “ACC” or “LOCK” position. They can­not, however, be operated once either front door is opened.
Vehicles with a smart key system
The power windows can be operated for approximately 45 seconds even after the “ENGINE ST ART STOP” switch is turned to ACCESSORY mode or turned off. They cannot, however, be operated once either front door is opened.
Jam protection function (driver’s window only)
If an object becomes caught between the window and the window frame, window travel is stopped and the window is opened slightly.
When the power window does not close normally (driver’s window
only)
If the jam protection function is operating abnormally and a window cannot be closed, perform the following operations using the power window switch on the driver’s door.
Vehicles without a smart key system: After stopping the vehicle, the win-
dow can be closed by holding the power window switch in the one-touch closing position while the engine switch is turned to the “ON” position.
Vehicles with a smart key system: After stopping the vehicle, the window
can be closed by holding the power window switch in the one-touch clos­ing position while the “ENGINE START STOP” switch is turned to IGNI­TION ON mode.
If the window still cannot be closed even by carrying out the operation
explained above, initialize the function by performing the following proce­dure.
82
Page 69
1-4. Opening and closing the windows and moon roof
STEP
1
Hold the power window switch in the one-touch closing position. Continue holding the switch for a further 6 seconds after the win­dow has closed.
STEP
2
Hold the power window switch in the one-touch opening position. Continue holding the switch for a further 2 seconds after the win­dow has opened completely.
STEP
3
Hold the power window switch in the one-touch closing position once again. Continue holding the switch for a further 2 seconds after the window has closed.
If you release the switch while the window is moving, start again from the beginning. If the window continues to close but then re-open slightly even after perform­ing the above procedure correctly, have the vehicle inspected by your Toyota dealer.
Customization that can be configured at Toyota dealer
Settings (e.g. key linked operation) can be changed. (Customizable features: P. 493)
1
Before driving
CAUTION
Closing the windows
Observe the following precautions. Failure to do so may result in death or serious injury.
Check to make sure that all passengers do not have any part of their body
in a position where it could be caught when a window is being operated.
Do not allow children to operate the power windows.
Closing a power window on someone can cause serious injury, and in some instances, even death.
Jam protection function (driver’s window only)
Never use any part of your body to intentionally activate the jam protection
function.
The jam protection function may not work if something gets caught just
before the window fully closes.
83
Page 70
1-4. Opening and closing the windows and moon roof
Moon roof
Use the overhead switches to open and close the moon roof and tilt it up and down.
Opening and closing
Tilt up and down
Opens
The moon roof stops slightly before the fully open position to reduce wind noise.
Press the switch again to fully open the moon roof.
Closes
*: Lightly press the switch in either
direction to stop the moon roof partway.
T
the moon roof
the moon roof
ilts the moon roof up
Tilts the moon roof down
*: Lightly press either of the moon
roof switches to stop the moon roof partway.
*
*
*
*
84
: If equipped
Page 71
1-4. Opening and closing the windows and moon roof
The moon roof can be operated when
Vehicles without a smart key system
The engine switch is in the “ON” position.
Vehicles with a smart key system
The “ENGINE START STOP” switch is in IGNITION ON mode.
Operating the moon roof after turning the engine off
Vehicles without a smart key system
The moon roof can be operated for approximately 45 seconds after the engine switch is turned to the “ACC” or “LOCK” position. It cannot, however, be operated once either front door is opened.
Vehicles with a smart key system
The moon roof can be operated for approximately 45 seconds after the “ENGINE START STOP” switch is turned to ACCESSORY mode or turned off. It cannot, however, be operated once either front door is opened.
Jam protection function
If an object is detected between the moon roof and the frame while the moon roof is closing or tilting down, travel is stopped and the moon roof opens slightly.
Sunshade
The sunshade can be opened and closed manually. However, the sunshade will open automatically when the moon roof is opened.
1
Before driving
85
Page 72
1-4. Opening and closing the windows and moon roof
When the moon roof does not close normally
Perform the following procedure:
If the moon roof closes but then re-opens slightly
STEP
1
Stop the vehicle.
STEP
2
Press and hold the “CLOSE” switch.*
1
The moon roof will close, reopen and pause for approximately 10 seconds.*
2
Then it will close again, tilt up and pause for approxi-
mately 1 second. Finally, it will tilt down, open and close.
STEP
3
Check to make sure that the moon roof is completely closed and then release the switch.
If the moon roof tilts down but then tilts back up
STEP
1
Stop the vehicle.
STEP
2
Press and hold the “UP” switch*
1
until the moon roof moves into the
tilt up position and stops.
STEP
3
Release the “UP” switch once and then press and hold the “UP” switch again.*
1
The moon roof will pause for approximately 10 seconds in the tilt up position.*
2
Then it will adjust slightly and pause for approximately 1
second. Finally, it will tilt down, open and close.
STEP
4
Check to make sure that the moon roof is completely closed and then release the switch.
1
*
: If the switch is released at the incorrect time, the procedure will have to
be performed again from the beginning.
2
: If the switch is released after the above mentioned 10 second pause,
*
automatic operation will be disabled. In that case, press and hold the open/close switch in the close position or press and hold the “UP” switch. The moon roof will tilt up and pause for approximately 1 second. Then it will tilt down, open and close. Check to make sure that the moon roof is completely closed and then release the switch.
If the moon roof does not fully close even after performing the above proce­dure correctly, have the vehicle inspected by your Toyota dealer.
86
Page 73
1-4. Opening and closing the windows and moon roof
Moon roof open reminder function
Vehicles without a smart key system
An alarm will sound when the driver’s door is opened with the moon roof not fully closed and the engine switch off.
Vehicles with a smart key system
An alarm will sound when the driver’s door is opened with the moon roof not fully closed and the “ENGINE START STOP” switch off.
Customization that can be configured at Toyota dealer
Settings (e.g. key linked operation) can be changed. (Customizable features: P. 493)
CAUTION
Opening the moon roof
Observe the following precautions. Failure to do so may cause death or serious injury.
Do not allow any passengers to put their hands or heads outside the vehi-
cle while it is moving.
Do not sit on top of the moon roof.
Closing the moon roof
Observe the following precautions. Failure to do so may result in death or serious injury.
Check to make sure that all passengers do not have any part of their bod-
ies in a position where they could be caught when the moon roof is being operated.
Do not allow children to operate the moon roof.
Closing the moon roof on someone can cause death or serious injury.
Jam protection function
Never use any part of your body to intentionally activate the jam protection
function.
The jam protection function may not work if something gets caught just
before the moon roof fully closes.
1
Before driving
87
Page 74

1-5. Refueling

Opening the fuel tank cap
Perform the following steps to open the fuel tank cap:
Before refueling the vehicle
Vehicles without a smart key system
Turn the engine switch off and ensure that all the doors and win­dows are closed.
Vehicles with a smart key system
Turn the “ENGINE START STOP” switch off and ensure that all the doors and windows are closed.
Opening the fuel tank cap
STEP
STEP
1
Pull up the opener to open the fuel filler door.
2
Turn the fuel tank cap slowly to open.
88
Page 75
1-5. Refueling
STEP
3
Closing the fuel tank cap
Hang the fuel tank cap on the back of the fuel filler door.
1
Before driving
After refueling, turn the fuel tank cap until you hear a click. Once the cap is released, it will turn slightly in the opposite direction.
89
Page 76
1-5. Refueling
CAUTION
When refueling the vehicle
Observe the following precautions while refueling the vehicle. Failure to do so may result in death or serious injury.
After exiting the vehicle and before opening the fuel door, touch an
unpainted metal surface to discharge any static electricity. It is important to discharge static electricity before refueling because sparks resulting from static electricity can cause fuel vapors to ignite while refueling.
Always hold the grips on the fuel tank cap and turn it slowly to remove it.
A whooshing sound may be heard when the fuel tank cap is loosened. Wait until the sound cannot be heard before fully removing the cap. In hot weather, pressurized fuel may spray out the filler neck and cause injury.
Do not allow anyone that has not discharged static electricity from their
body to come close to an open fuel tank.
Do not inhale vaporized fuel.
Fuel contains substances that are harmful if inhaled.
Do not smoke while refueling the vehicle.
Doing so may cause the fuel to ignite and cause a fire.
Do not return to the vehicle or touch any person or object that is statically
charged. This may cause static electricity to build up, resulting in a possible ignition hazard.
When refueling
Securely insert the fuel nozzle into the fuel filler neck. If fuel is added with the nozzle slightly lifted away from the fuel filler neck, the automatic shut off function may not operate, resulting in fuel overflowing from the tank.
When replacing the fuel cap
Do not use anything but a genuine Toyota fuel tank cap designed for your vehicle. Doing so may cause a fire or other incident which may result in death or serious injury.
90
Page 77
1-5. Refueling
NOTICE
Refueling
Do not spill fuel during refueling. Doing so may damage the vehicle, such as causing the exhaust systems to operate abnormally or damaging fuel system components or the vehicle's painted surface.
1
Before driving
91
Page 78

1-6. Theft deterrent system

Engine immobilizer system
The vehicle's keys have built-in transponder chips that prevent the engine from starting if a key has not been previously registered in the vehicle's on-board computer.
Never leave the keys inside the vehicle when you leave the vehicle.
Vehicles without a smart key system
The indicator light flashes after the key has been removed from the engine switch to indi­cate that the system is operat­ing.
The indicator light stops flash­ing after the registered key has been inserted into the engine switch to indicate that the system has been can­celed.
92
Vehicles with a smart key system
The indicator light flashes after the “ENGINE START STOP” switch has been turned off to indicate that the system is operating.
The indicator light stops flash­ing after the “ENGINE START STOP” switch has been turned to ACCESSORY or IGNITION ON mode to indicate that the system has been canceled.
Page 79
1-6. Theft deterrent system
System maintenance
The vehicle has a maintenance-free type engine immobilizer system.
Conditions that may cause the system to malfunction
If the grip portion of the key is in contact with a metallic object
If the key is in close proximity to or touching a key to the security system
(key with a built-in transponder chip) of another vehicle
Certifications for the engine immobilizer system
U.S.A.
Vehicles without a smart key system FCC ID: WRKRI-34BTY This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful interfer­ence, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Vehicles with a smart key system FCC ID: NI4TMIMB-3
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interfer­ence, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Canada
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, includ­ing interference that may cause undesired operation of the device.
1
Before driving
CAUTION
Certifications for the immobilizer system
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
93
Page 80
1-6. Theft deterrent system
NOTICE
To ensure the system operates correctly
Do not modify or remove the system. If modified or removed, the proper operation of the system cannot be guaranteed.
94
Page 81
1-6. Theft deterrent system
Alarm
The system sounds the alarm and flashes the lights when forced entry is detected.
Triggering of the alarm
The alarm is triggered in the following situations when the alarm is set:
A locked door or trunk is unlocked or opened in any way other than using the entry function, wireless remote control or mechanical key.
The hood is opened.
Some models: The window is tapped or broken.
Setting the alarm system
Close the doors, trunk and hood, and lock all the doors. The system will be set auto­matically after 30 seconds.
1
Before driving
The indicator light changes from being on to flashing when the system is set.
: If equipped
95
Page 82
1-6. Theft deterrent system
Deactivating or stopping the alarm
Do one of the following to deactivate or stop the alarm.
Unlock the doors or trunk.
Vehicles without a smart key system: Turn the engine switch
to the “ACC” or “ON” position, or start the engine. (The alarm will be deactivated or stopped after a few seconds.)
Vehicles with a smart key system: Turn the “ENGINE START STOP” switch to ACCESSORY or IGNITION ON mode, or start the engine. (The alarm will be deactivated or stopped after a few seconds.)
System maintenance
The vehicle has a maintenance-free type alarm system.
Items to check before locking the vehicle
To prevent unexpected triggering of the alarm and vehicle theft, make sure of the following:
Nobody is in the vehicle.
The windows and moon roof are closed before the alarm is set.
No valuables or other personal items are left in the vehicle.
96
Page 83
Triggering of the alarm
The alarm may be triggered in the following situations. (Stopping the alarm deactivates the system.)
1-6. Theft deterrent system
A person inside the vehicle opens a
door, the trunk or hood.
The battery is recharged or replaced
when the vehicle is locked.
Alarm-operated door lock
When the alarm is operating, the doors are locked automatically to pre-
vent intruders.
Do not leave the key inside the vehicle when the alarm is operating, and
make sure the key is not inside the vehicle when recharging or replacing the battery.
NOTICE
1
Before driving
To ensure the system operates correctly
Do not modify or remove the system. If modified or removed, the proper operation of the system cannot be guaranteed.
97
Page 84

1-7. Safety information

Correct driving posture
Drive in a good posture as follows:
Sit upright and well back in the seat. (P. 62)
Adjust the position of the seat forward or backward to ensure the pedals can be reached and easily depressed to the extent required. (P. 62)
Adjust the seatback so that the controls are easily oper­able.
Adjust the tilt and telescopic positions of the steering wheel downward so the air­bag is facing your chest. (P. 76)
Lock the head restraint in place with the center of the head restraint closest to the top of your ears. (P. 67)
Wear the seat belt correctly. (P. 69)
98
Page 85
1-7. Safety information
CAUTION
While driving
Do not adjust the position of the driver’s seat.
Doing so could cause the driver to lose control of the vehicle.
Do not place a cushion between the driver or passenger and the seatback.
A cushion may prevent correct posture from being achieved, and reduce the effectiveness of the seat belt and head restraint, increasing the risk of death or serious injury to the driver or passenger.
Do not place anything under the front seats.
Objects placed under the front seats may become jammed in the seat tracks and stop the seat from locking in place. This may lead to an acci­dent, resulting in death or serious injury. The adjustment mechanism may also be damaged.
Adjusting the seat position
Take care when adjusting the seat position to ensure that other passen-
gers are not injured by the moving seat.
Do not put your hands under the seat or near the moving parts to avoid
injury. Fingers or hands may become jammed in the seat mechanism.
1
Before driving
99
Page 86
1-7. Safety information
SRS airbags
The SRS airbags inflate when the vehicle is subjected to certain types of severe impacts that may cause significant injury to the occupants. They work together with the seat belts to help reduce the risk of death or serious injury.
SRS front airbags
SRS driver airbag/front passenger airbag Can help protect the head and chest of the driver a nd front pas­senger from impact with interior components
SRS knee airbags Can help provide driver and front passenger protection
SRS side and curtain shield airbags
SRS front side airbags Can help protect the torso of the front seat occupants
SRS rear side airbags Can help protect the torso of occupants in the rear outer seats
100
Page 87
1-7. Safety information
SRS curtain shield airbags Can help protect primarily the head of occupants in the outer seats
1
SRS airbag system components
Front impact sensors Front passenger occupant
classification system (ECU and sensors)
Knee airbags Side impact sensors (front
door) Side impact sensors (front) Front passenger airbag Front side airbags Curtain shield airbags Rear side airbags
Before driving
“AIR BAG ON” and “AIR BAG OFF” indicator lights
SRS warning light Front passenger’s seat belt
buckle switch Airbag sensor assembly Side impact sensors (rear) Driver airbag Driver’s seat belt buckle
switch Seat belt pretensioners and
force limiters
101
Page 88
1-7. Safety information
Your vehicle is equipped with ADVANCED AIRBAGS designed based on the US motor vehicle safety standards (FMVSS208). The airbag sensor assembly (ECU) controls airbag deployment based on infor­mation obtained from the sensors etc. shown in the system compo­nents diagram above. This information includes crash severity and occupant information. As the airbags deploy, a chemical reaction in the inflators quickly fills the airbags with nontoxic gas to help restrain the motion of the occupants.
102
Page 89
1-7. Safety information
If the SRS airbags deploy (inflate)
Bruising and slight abrasions may result from contact with a deploying
(inflating) SRS airbag.
A loud noise and white powder will be emitted.
Parts of the airbag module (steering wheel hub, airbag cover and inflator)
as well as the seats, parts of the front and rear pillars, and roof side rails, may be hot for several minutes. The airbag itself may also be hot.
The windshield may crack.
For Safety Connect subscribers, if the SRS airbags deploy or in the event
of a severe rear-end collision, the system is designed to send an emer­gency call to the response center, notifying them of the vehicle’s location (without needing to push the “SOS” button) and an agent will attempt to speak with the occupants to ascertain the level of emergency and assis­tance required. If the occupants are unable to communicate, the agent automatically treats the call as an emergency and helps to dispatch the necessary emergency services. (P. 326)
SRS airbag deployment conditions (SRS front airbags)
The SRS front airbags will deploy in the event of an impact that exceeds
the set threshold level (the level of force corresponding to an approxi­mately 12 - 18 mph [20 - 30 km/h] frontal collision with a fixed wall that does not move or deform).
However, this threshold velocity will be considerably higher if the vehicle strikes an object, such as a parked vehicle and sign pole, which can move or deform on impact, or if the vehicle is involved in an underride collision (e.g. a collision in which the front of the vehicle “underrides”, or goes under, the bed of a truck etc.).
Depending on the type of collision, it is possible that only the seat belt
pretensioners will activate.
The SRS front airbags for the front passenger will not activate if there is
no passenger sitting in the front passenger seat. However, the SRS front airbags for the front passenger may deploy if luggage is put in the seat, even if the seat is unoccupied. (P. 113)
1
Before driving
103
Page 90
1-7. Safety information
SRS airbag deployment conditions (SRS side and curtain shield air-
bags)
The SRS side and curtain shield airbags will deploy in the event of an
impact that exceeds the set threshold level (the level of force corre­sponding to the impact force produced by an approximately 3300 lb. [1500 kg] vehicle colliding with the vehicle cabin from a direction perpen­dicular to the vehicle orientation at an approximate speed of 12 - 18 mph [20 - 30 km/h]).
The SRS curtain shield airbags may also deploy in the event of a severe
frontal collision.
Conditions under which the SRS airbags may deploy (inflate), other
than a collision
The SRS front airbags and SRS curtain shield airbags may also deploy if a serious impact occurs to the underside of your vehicle. Some examples are shown in the illustration.
Hitting a curb, edge of pavement or
hard surface
Falling into or jumping over a deep hole
Landing hard or falling
104
Page 91
1-7. Safety information
Types of collisions that may not deploy the SRS airbags (SRS front air-
bags)
The SRS front airbags do not generally inflate if the vehicle is involved in a side or rear collision, if it rolls over, or if it is involved in a low-speed frontal collision. But, whenever a collision of any type causes sufficient forward deceleration of the vehicle, deployment of the SRS front airbags may occur.
Collision from the side
Collision from the rear
Vehicle rollover
1
Before driving
105
Page 92
1-7. Safety information
Types of collisions that may not deploy the SRS airbags
(SRS side and curtain shield airbags)
The SRS side and curtain shield airbags may not activate if the vehicle is subjected to a collision from the side at certain angles, or a collision to the side of the vehicle body other than the passenger compartment.
Collision from the side to the vehicle
body other than the passenger com­partment
Collision from the side at an angle
SRS side airbags: Do not generally inflate if the vehicle is involved in a fron­tal or rear collision, if it rolls over, or if it is involved in a low-speed side colli­sion.
SRS curtain shield airbags: Do not generally inflate if the vehicle is involved in a rear collision, if it rolls over, or if it is involved in a low-speed side colli­sion.
106
Collision from the front*
Collision from the rear
Vehicle rollover
*: Depending on the conditions and type
of accident, the curtain shield airbags may deploy (inflate) upon frontal impact.
Page 93
1-7. Safety information
When to contact your Toyota dealer
In the following cases, contact your Toyota dealer as soon as possible.
Any of the SRS airbags have been inflated.
The front of the vehicle is damaged or
deformed, or was involved in an acci­dent that was not severe enough to cause the SRS front airbags and SRS curtain shield airbags to inflate.
A portion of a door is damaged or
deformed, or the vehicle was involved in an accident that was not severe enough to cause the SRS side and cur­tain shield airbags to inflate.
The pad section of the steering wheel,
dashboard near the front passenger air­bag or lower portion of the instrument panel is scratched, cracked, or other­wise damaged.
The surface of the seats with the side
airbag is scratched, cracked, or other­wise damaged.
The portion of the front pillars, rear pil-
lars or roof side rail garnishes (padding) containing the curtain shield airbags inside is scratched, cracked, or other­wise damaged.
1
Before driving
107
Page 94
1-7. Safety information
CAUTION
SRS airbag precautions
Observe the following precautions regarding the SRS airbags. Failure to do so may cause death or serious injury.
The driver and all passengers in the vehicle must wear their seat belts
properly. The SRS airbags are supplemental devices to be used with the seat belts.
The SRS driver airbag deploys with considerable force, and can cause
death or serious injury especially if the driver is very close to the airbag. The National Highway Traffic Safety Administration (NHTSA) advises:
Since the risk zone for the driver’s airbag is the first 2 - 3 in. (50 - 75 mm) of inflation, placing yourself 10 in. (250 mm) from your driver airbag pro­vides you with a clear margin of safety . This dist ance is measured from the center of the steering wheel to your breastbone. If you sit less than 10 in. (250 mm) away now, you can change your driving position in several ways:
• Move your seat to the rear as far as you can while still reaching the pedals comfortably.
• Slightly recline the back of the seat. Although vehicle designs vary, many drivers can achieve the 10 in. (250 mm) distance, even with the driver seat all the way forward, sim­ply by reclining the back of the seat somewhat. If reclining the back of your seat makes it hard to see the road, raise yourself by using a firm, non-slippery cushion, or raise the seat if your vehicle has that feature.
• If your steering wheel is adjustable, tilt it downward. This points the air­bag toward your chest instead of your head and neck.
The seat should be adjusted as recommended by NHTSA above, while still maintaining control of the foot pedals, steering wheel, and your view of the instrument panel controls.
108
Page 95
CAUTION
SRS airbag precautions
1-7. Safety information
If the seat belt extender has been con-
nected to the front seat belt buckles but the seat belt extender has not also been fastened to the latch plate of the seat belt, the SRS front airbags will judge that the driver and front passen­ger are wearing the seat belt even though the seat belt has not been con­nected. In this case, the SRS front air­bags may not activate correctly in a collision, resulting in death or serious injury in the event of a collision. Be sure to wear the seat belt with the seat belt extender.
The SRS front passenger airbag also deploys with considerable force, and
can cause death or serious injury especially if the front passenger is very close to the airbag. The front passenger seat should be as far from the air­bag as possible with the seatback adjusted, so the front passenger sits upright.
Improperly seated and/or restrained infants and children can be killed or
seriously injured by a deploying airbag. An infant or child who is too small to use a seat belt should be properly secured using a child restraint sys­tem. Toyota strongly recommends that all infants and children be placed in the rear seats of the vehicle and properly restrained. The rear seats are safer for infants and children than the front passenger seat. (P. 118)
1
Before driving
Do not sit on the edge of the seat or
lean against the dashboard.
109
Page 96
1-7. Safety information
CAUTION
SRS airbag precautions
Do not allow a child to stand in front of
the SRS front passenger airbag unit or sit on the knees of a front passenger.
Do not allow the front seat occupants to
hold items on their knees.
Do not lean against the door, the roof
side rail or the front, side and rear pil­lars.
Do not allow anyone to kneel on the
passenger seats toward the door or put their head or hands outside the vehicle.
110
Do not attach anything to or lean any-
thing against areas such as the dash­board, steering wheel pad and lower portion of the instrument panel. These items can become projectiles when the SRS driver, front passenger and knee airbags deploy.
Page 97
CAUTION
SRS airbag precautions
1-7. Safety information
Do not attach anything to areas such as
a door, windshield glass, side door glass, front or rear pillar, roof side rail and assist grip.
Vehicles without a smart key system:
Do not attach any heavy, sharp or hard objects such as keys and accessories to the key. The objects may restrict the SRS knee airbag inflation or be thrust into the driver's seat area by the force of the deploying airbag, thus causing a danger.
Do not hang coat hangers or other hard objects on the coat hooks. All of
these items could become projectiles and may cause death or serious injury, should the SRS curtain shield airbags deploy.
If a vinyl cover is put on the area where the SRS knee airbag will deploy,
be sure to remove it.
Do not use seat accessories which cover the parts where the SRS side
airbags inflate as they may interfere with inflation of the airbags. Such accessories may prevent the side airbags from activating correctly, disable the system or cause the side airbags to inflate accidentally, resulting in death or serious injury.
Do not strike or apply significant levels of force to the area of the SRS air-
bag components. Doing so can cause the SRS airbags to malfunction.
Do not touch any of the component parts immediately after the SRS air-
bags have deployed (inflated) as they may be hot.
1
Before driving
111
Page 98
1-7. Safety information
CAUTION
SRS airbag precautions
If breathing becomes difficult after the SRS airbags have deployed, open a
door or window to allow fresh air in, or leave the vehicle if it is safe to do so. Wash off any residue as soon as possible to prevent skin irritation.
If the areas where the SRS airbags are stored, such as the steering wheel
pad and front and rear pillar garnishes, are damaged or cracked, have them replaced by your Toyota dealer.
Modification and disposal of SRS airbag system components
Do not dispose of your vehicle or perform any of the following modifications without consulting your Toyota dealer. The SRS airbags may malfunction or deploy (inflate) accidentally, causing death or serious injury.
Installation, removal, disassembly and repair of the SRS airbags
Repairs, modifications, removal or replacement of the steering wheel,
instrument panel, dashboard, seats or seat upholstery, front, side and rear pillars or roof side rails
Repairs or modifications of the front fender, front bumper, or side of the
occupant compartment
Installation of snow plows, winches, etc. to the front grille (bull bars or kan-
garoo bar etc.)
Modifications to the vehicle's suspension system
Installation of electronic devices such as mobile two-way radios and CD
players
Modifications to your vehicle for a person with a physical disability
112
Page 99
1-7. Safety information
Front passenger occupant classification system
Your vehicle is equipped with a front passenger occupant classifica­tion system. This system detects the conditions of the front passen­ger seat and activates or deactivates the devices for the front passenger.
1
Before driving
SRS warning light Seat belt reminder light “AIR BAG OFF” indicator light “AIR BAG ON” indicator light
113
Page 100
1-7. Safety information
Condition and operation in the front passenger occupant classification system
Adult
*1
“AIR BAG ON” and “AIR BAG OFF”
Indicator/
warning light
indicator lights
SRS warning light Off
Seat belt reminder light Flashing Front passenger airbag
Side airbag on the front
passenger seat
Devices
Curtain shield airbag in the front
passenger side
Front passenger knee airbag
Front passenger’s seat belt pretensioner
Child*3 or child restraint system
“AIR BAG ON” and “AIR BAG OFF”
Indicator/
warning light
Devices
Curtain shield airbag in the front
Front passenger knee airbag Deactivated
Front passenger’s seat belt pretensioner Activated
indicator lights
SRS warning light Off
Seat belt reminder light Flashing Front passenger airbag Deactivated
Side airbag on the front
passenger seat
passenger side
“AIR BAG
ON”
*2
Activated
*4
“AIR BAG
*5
OFF”
*2
Activated
114
Loading...