1. Master keys (black)—
These keys work in every lock. Your
Toyota dealer will need one of them to
make a new key with a built−in transponder chip.
Since the doors and trunk lid can be
locked without a key, you should always carry a spare master key in case
you accidentally lock your keys inside
the vehicle.
Type B only—This key is fitted with the
wireless remote control transmitter. For
information on use of the wireless remote control transmitter, see “Wireless
remote control” on page 20 in this Section.
2. Sub key (gray)—
This key will not work in the glove box,
trunk and the door located behind the
rear seat armrest (on some models).
To protect items locked in the trunk or
glove box when using valet parking,
leave the sub key with the attendant.
A transponder chip for engine immobilizer
system has been placed in the head of
the master and sub keys. These chips are
needed to enable the system to function
correctly, so be careful not to lose these
keys. If you make your own duplicate key,
you will not be able to cancel the system
or start the engine.
Type B
14
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
’07Camry_U (L/O 0608)
NOTICE
When using a key containing a transponder chip, observe the following
precautions:
When starting the engine, do not
use the key with a key ring resting
on the key grip and do not press
the key ring against the key grip.
Otherwise the engine may not start,
or may stop soon after it starts.
When starting the engine, do not
use the key with other transponder
keys around (including keys of other vehicles) and do not press other
key plates against the key grip.
Otherwise the engine may not start,
or may stop soon after it starts. If
this happens, remove the key once
and then insert it again after removing other transponder keys (including keys of other vehicles) from the
ring or while gripping or covering
them with your hand to start the
engine.
Do not bend the key grip.
15
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
Do not cover the key grip with any
material that cuts off electromagnetic waves.
Do not knock the key hard against
other objects.
Do not leave the key exposed to
high temperatures for a long period,
such as on the dashboard and hood
under direct sunlight.
Do not put the key in water or
wash it in an ultrasonic washer.
Do not use the key with electromagnetic materials.
’07Camry_U (L/O 0608)
KEY NUMBER PLATE
Your key number is shown on the plate.
Keep the plate in a safe place such as
your wallet, not in the vehicle.
If you should lose your keys or if you
need additional keys, duplicates can be
made by a Toyota dealer using the key
number.
We recommend writing down the key number and storing it in a safe place.
Keys (with smart key system)
The key consists of an electronic key
and a mechanical key. The mechanical
key is for emergency use. If the electronic key does not operate, you can
open the driver’s door using the mechanical key.
1. Electronic keys—These keys can lock
or unlock all the doors and can open
the trunk by using the wireless remote
control function or entry function of the
smart key system.
2. Mechanical keys—These keys can lock
or unlock the driver’s door, the glove
box and the door located behind the
rear seat armrest.
16
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
’07Camry_U (L/O 0608)
Spare keys should not be left in the
cabin. In the event that a spare key is
left in the cabin, the smart key system
will remain actuated even after the
doors have been locked. Under these
circumstances, the trunk can be opened
even after the driver has exited and
locked the vehicle, increasing the danger of theft. (Refer to “OPENING
TRUNK WITH SMART KEY SYSTEM” on
page 46 in this Section.)
To protect items locked in the trunk or the
glove box when using valet parking, leave
the electronic key with the attendant. Keep
the mechanical key with you. For details
about locking the trunk opener switch, see
“—Luggage security system” on page 47
in this Section.
A transponder chip for engine immobilizer
system has been placed in the electronic
keys. These chips are needed to enable
the system to function correctly, so be
careful not to lose these keys.
CAUTION
People with implanted pacemakers
or cardiac defibrillators should keep
away from the smart key system
antennas, because the radio waves
may affect the operation of such
devices. For the antenna locations
see “ANTENNA LOCATION” on page
32 in this Section.
Users of any electrical medical de-
vice other than implanted pacemakers and implanted cardiac defibrillators should consult the manufacturer of the device for information
about its operation under the influence of radio waves. Radio waves
could have unexpected effects on
the operation of such medical devices.
If necessary, the entry function can
be disabled. See “DISABLING THE
SMART KEY SYSTEM” on page 36
in this Section.
NOTICE
When using a electronic key containing a transponder chip, observe the
following precautions:
Do not affix any material that cuts
off electromagnetic waves (such as
a metal seal) on the electronic key.
Do not knock the electronic key
hard against other objects.
Do not leave the electronic key exposed to high temperatures for a
long period, such as on the dashboard or hood under direct sunlight.
Do not put the electronic key in
water or wash it in an ultrasonic
washer.
Do not keep the electronic key together with the products emitting
electromagnetic waves such as a
cellular phone.
17
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
’07Camry_U (L/O 0608)
Engine immobilizer system
The engine immobilizer system is a
theft prevention system using an electronic code. The transponder chip in
the key has an electronic code and
transmits the code to the vehicle. Only
when the electronic code in the chip
corresponds to the register ID code for
the vehicle, the engine immobilizer system will be canceled and the engine
will start.
USING A MECHANICAL KEY
When you use the mechanical key push
the release button and take out the mechanical key as shown. Be sure to put the
mechanical key back when not it use.
18
KEY NUMBER PLATE
Your key number is shown on the plate.
Keep the plate in a safe place such as
your wallet, not in the vehicle.
If you should lose your keys or if you
need additional keys, duplicates can be
made by Toyota dealer using the key
number.
We recommend writing down the key number and storing it in a safe place.
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
’07Camry_U (L/O 0608)
The engine immobilizer system is automatically set when:
Vehicles with key cylinder−type ignition
switch—The key is removed from the ignition switch.
Vehicles with smart key system—The ignition switch is turned off.
The indicator light will start flashing to
show that the system is set.
If any of the following indicator conditions
occur, contact your Toyota dealer.
The indicator light stays on except
when the theft deterrent system is setting or activating. (See “Theft deterrent
system” on page 49 in this Section.)
The indicator light does not start flash-
ing under the following situations.
Vehicles with key cylinder−type ignition
switch—When the key is removed from
the ignition switch.
Vehicles with smart key system—When
the ignition switch is turned off.
The indicator light flashes inconsistent-
ly.
The engine immobilizer system is automatically canceled when:
Vehicles with key cylinder−type ignition
switch—
You insert the key to the ignition switch.
Vehicles with smart key system—
You enter the vehicle carrying a key with
smart key system and press the “ENGINE
START STOP” switch (engine switch).
Even if the key battery is discharged, the
engine can be started. See “Smart key
system” on page 30 in this Section.
When the system is canceled, the indicator light will go off.
For your Toyota dealer to make you a
new key with built−in transponder chip,
your dealer will need your key number
and master key (vehicles with key cylinder−type ignition switch) or electronic key
(vehicles with smart key system). However, there is a limit to the number of additional keys your Toyota dealer can make
for you.
NOTICE
Do not modify, remove or disassemble the engine immobilizer system. If any unauthorized changes or
modifications are made, proper operation of the system cannot be guaranteed.
19
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
For vehicles sold in U.S.A.
’07Camry_U (L/O 0608)
Wireless remote control—
For vehicles sold in Canada
Key cylinder−type ignition switch
FCC ID: MOZRI−20BTY
FCC ID: MOZRI−21BTY
Smart key system
FCC ID: NI4TMIMB−1
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
CAUTION
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
This device complies with RSS−210 of
Industry Canada. Operation is subject to
the following two conditions:
(1) This device may not cause interference, and (2) this device must accept
any interference, including interference
that may cause undesired operation of
the device.
Vehicles with key cylinder−type ignition
switch
Vehicles with smart key system
20
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
’07Camry_U (L/O 0608)
1. Indicator light
2. Lock switch
3. Alarm switch
4. Unlock switch
5. Trunk opener switch
The wireless remote control function is
designed to lock or unlock all the
doors, open the trunk lid, or activate
the alarm from a distance within
approximately 1 m (3 ft.) of the vehicle.
When you operate any switch, push it
slowly and securely.
When the switch is operated, the indicator
light flashes once. If not, the battery may
be discharged. Replace the battery at the
earliest opportunity.
The wireless remote control transmitter is
an electronic component. Observe the following instructions in order not to cause
damage the key.
Do not leave the transmitter in places
where the temperature becomes high
such as on the dashboard.
Do not disassemble it.
Avoid knocking it hard against other
objects or dropping it.
Avoid putting it in water.
You can use up to 4 wireless remote control keys (for vehicles with key cylinder−
type ignition switch) or 5 wireless remote
control transmitters (for vehicles with
smart key system) for the same vehicle.
Contact your Toyota dealer for detailed
information.
If the wireless remote control transmitter
does not actuate the doors, or does not
operate from a normal distance, or if the
indicator on the transmitter is dimmed or
does not come on:
Check for closeness to a radio trans-
mitter such as a radio station or an
airport which can interfere with normal
operation of the key.
The battery may have been consumed.
Check the battery in the key. To replace the battery, see “—Replacing battery” on pages 26 or 28 in this Section.
If you lose your wireless remote control
key, contact your Toyota dealer as soon
as possible to avoid the possibility of
theft, or an accident. (See “If you lose
your keys” on page 356 in Section 4.)
It is possible to disable the wireless remote control system. For details, contact
your Toyota dealer.
21
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
’07Camry_U (L/O 0608)
For vehicles sold in U.S.A.
This device complies with Part 15 of the
FCC Rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful
interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
NOTICE:
This equipment has been tested and
found to comply with the limits for a
Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment
generates, uses and can radiate radio
frequency energy and, if not installed
and used in accordance with the instructions, may cause harmful interference to
radio communications. However, there is
no guarantee that interference will not
occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception,
which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
Reorient or relocate the receiving an-
tenna.
Increase the separation between the
equipment and receiver.
Connect the equipment into an outlet
on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced
radio/TV technician for help.
FCC WARNING:
Changes or modifications not expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
For vehicles sold in Canada
Operation is subject to the following two
conditions:
(1) this device may not cause interference, and (2) this device must accept
any interference, including interference
that may cause undesired operation of
the device.
22
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
—Locking and unlocking
doors
Locking operation (vehicles with key cylinder−type ignition switch)
’07Camry_U (L/O 0608)
Locking operation (vehicles with smart
key system)
To lock or unlock all the doors, push
the switches slowly and securely.
To lock: Push the lock switch. All the
doors are locked simultaneously. At this
time one beep will sound and turn signal
lights flash once.
Check to see that the doors are securely
locked.
If any of the doors is not securely closed,
or if the key is in the ignition switch (vehicles with key cylinder−type ignition
switch) or key left in the vehicle (vehicles
with smart key system), locking cannot be
performed by the lock switch and a beep
will sound continuously for 10 seconds.
To stop the beep, take out the key from
the vehicle or push the unlock switch.
The answerback function (the turn signal
flash and the beep) can be disabled. For
details, contact your Toyota dealer.
Unlocking operation (vehicles with key
cylinder−type ignition switch)
Unlocking operation (vehicles with smart
key system)
23
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
To unlock: Push the unlock switch once to
unlock the driver’s door alone. Pushing
the switch twice within 3 seconds unlocks
all the doors simultaneously. Each time
the unlock switch is pushed, two beeps
will sound and turn signal lights flash
twice.
This double switch operation to unlock all
doors can be changed to a single switch
operation. For details, contact your Toyota
dealer.
If the key is in the ignition (vehicles with
key cylinder−type ignition switch) or the
ignition switch is set to ACC or ON (vehicles with smart key system), the vehicle
cannot be unlocked via the unlock switch.
You have 60 seconds to open a door after
using the wireless remote unlock feature.
If a door is not opened by then, all the
doors will be automatically locked again.
If the wireless remote control is used to
lock the doors near the window or door
handle, there is a possibility that the door
may not unlocked by entry function of
smart key system. Under these circumstances, use the wireless remote control
to unlock the doors.
’07Camry_U (L/O 0608)
—Opening trunk lid
The automatic locking time can also be
set to 30 seconds. For details, contact
your Toyota dealer.
If the lock or unlock switch is kept
pressed in, the locking or unlocking operation is not repeated. Release the switch
and then push again.
When you unlock doors using the wireless
remote control, the illuminated entry function will be activated. (For further information, see “Illuminated entry system” on
page 128 in Section 1−5.)
Vehicles with key cylinder−type ignition
switch
24
Vehicles with smart key system
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
To open the trunk lid, push and hold
the trunk opener switch of the transmitter for 1 second. A long beep will
sound.
If the key is in the ignition (vehicles with
key cylinder−type ignition switch) or the
ignition switch is set at ACC or ON (vehicles with smart key system), the trunk
lid cannot be opened by the trunk opener
switch.
Opening of the trunk lid with the wireless
remote control can be changed as follows.
Contact your Toyota dealer for details.
Trunk lid opens by pushing the trunk
opener switch twice in succession.
Trunk lid opens by pushing the trunk
opener switch once regardless of how
long the switch is being pressed.
Opening of the trunk lid is disabled
using the wireless remote control transmitter.
’07Camry_U (L/O 0608)
—Activating alarm
Vehicles with key cylinder−type ignition
switch
Pushing the alarm switch for 1 second
or more blows the horn intermittently
and flashes the headlights, turn signal
lights, tail lights and interior light.
Vehicles with smart key system only—
When pushing the switch, the indicator
light flashes.
The alarm switch is used to deter vehicle
theft when you witness anyone attempting
to break into or damage your vehicle.
The alarm will last for one minute. To stop
the alarm midway, push any button on the
wireless remote control or set the ignition
switch to ON.
If the key is in the ignition (vehicles with
key cylinder−type ignition switch) or the
ignition switch is set at ACC or ON (vehicles with smart key system), the alarm
does not work.
This alarm function can be disabled. For
details, contact your Toyota dealer.
For replacement, use a CR2016 lithium
battery or equivalent.
CAUTION
Special care should be taken to prevent small children from swallowing
the removed battery or components.
NOTICE
When replacing the battery, be careful not to lose the components.
Replace only with the same or
equivalent type recommended by a
Toyota dealer.
Dispose of used batteries according
to the local laws.
’07Camry_U (L/O 0608)
1. Open the cover using a flathead screwdriver wrapped with plastic tape.
2. Remove the module from the key
frame.
Replace the battery by following these
procedures:
26
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
3. Open and remove the battery case
cover using a coin.
’07Camry_U (L/O 0608)
4. Take out the discharged transmitter
battery and put in a new battery with
the positive (+) side up.
5. Install the battery case cover and then
install the module into the key frame.
Close the cover.
6. When pushing either switch on the
wireless key, make sure the indicator
light comes on.
NOTICE
Do not bend the terminals.
Make sure the positive side and
negative side of the battery are
faced correctly.
Do not replace the battery with wet
hands. Water may cause unexpected
rust.
Do not touch or move any components inside the transmitter, or it
may interfere with proper operation.
Be careful not to bend the electrode
when inserting the battery and that
dust or oils do not adhere to the
case.
Close the cover securely.
27
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
After replacing the battery, check that the
key operates properly. If the key still does
not operate properly, contact your Toyota
dealer.
’07Camry_U (L/O 0608)
—Replacing battery
(with smart key system)
The transmitter can easily be damaged
when replacing the battery. We recommend having the battery replaced by your
Toyota dealer. If you have to do it yourself, use a CR1632 lithium battery or
equivalent and a flathead screwdriver.
CAUTION
Special care should be taken to prevent small children from swallowing
the removed transmitter battery or
components.
28
NOTICE
Be careful not to touch the circuit,
as this may generate static electricity that can damage the transmitter.
When replacing the transmitter battery, be careful not to lose the components.
Replace only with the same or
equivalent type recommended by a
Toyota dealer.
Dispose of used batteries according
to the local laws.
Replace the transmitter battery by following these procedures:
1. Push the release button and take out
the mechanical key.
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
’07Camry_U (L/O 0608)
2. Using a flathead screwdriver or equivalent, open the transmitter case.
3. Remove the discharged transmitter battery by flathead screwdriver or equivalent. Insert the guide groove and lift as
shown in the above illustration.
NOTICE
Do not modify the battery case. It
may cause a transmitter malfunction.
4. Put in a new battery with the positive
(+) side up. Install the cover and insert
the mechanical key into the transmitter.
Close the transmitter case securely.
29
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
NOTICE
Make sure the positive side and
negative side of the battery are
faced correctly.
Do not replace the battery with wet
hands. Water may cause unexpected
rust.
Do not touch or move any components inside the transmitter, or it
may interfere with proper operation.
Be careful not to bend the electrode
when inserting the transmitter battery and that dust or oils do not
adhere to the case.
Close the transmitter case securely.
After replacing the battery, check that the
transmitter operates properly. If the transmitter still does not operate properly, contact your Toyota dealer.
’07Camry_U (L/O 0608)
Smart key system
The smart key system consists mainly
of the following functions.
Engine immobilizer function (For de-
tails, see “Engine immobilizer system”
on page 18 in this Section.)
Wireless remote control function (For
details, see “Wireless remote control”
on page 20 in this Section.)
Push button start function (For details,
see “How to start the engine” on page
316 in Section 3.)
Entry function and start function (See
“ENTRY FUNCTION AND START
FUNCTION” described below.)
Steering lock function (See “STEERING
LOCK FUNCTION” described below.)
CAUTION
People with implanted pacemakers
or cardiac defibrillators should keep
away from the smart key system
antennas, because the radio waves
may affect the operation of such
devices. For the antenna locations
see “ANTENNA LOCATION” on page
32 in this Section.
Users of any electrical medical de-
vice other than implanted pacemakers and implanted cardiac defibrillators should consult the manufacturer of the device for information
about its operation under the influence of radio waves. Radio waves
could have unexpected effects on
the operation of such medical devices.
If necessary, the entry function can
be disabled. See “DISABLING THE
SMART KEY SYSTEM” on page 36
in this Section.
30
2007MY CAMRY from Oct. ’06 Prod. (OM33748U)
Loading...
+ 385 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.