Toshiba TDP-PX10 User Manual

TDP-PX10
DATA PROJECTOR

OWNER’S MANUAL

Before UsingPreparationsOperationsMaintenanceOthers

In the spaces provided below, record the Model and Serial No. located at the bottom of your
projector.

Model No.
Retain this information for future reference.

!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!Serial No.!!!!!!!!!!

Before using

SAFETY PRECAUTIONS

The lightning flash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated "dangerous vo ltage"
within the product's enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.

The exclamation point within an equilateral triangle i s intended to alert the user
to the presence of important operating and maintenance (servicing) instructions
in the literature accompanying the appliance.

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE

THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS HIGH
VOLTAGES ARE PRESENT INSIDE THE E NCLOSURE. DO NOT OPEN THE
CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.

WARNING: Handling the cord on this product or cords associated wi th accessories sold

USA ONLY

with this product, will expose you to lead, a ch emical known to the State of
California to cause birth defects or other reproductive harm. Wash hands

after handling.

USA ONLY

MODEL NAME: TDP-PX10!

TRADE NAME: DATA PROJECTOR MODEL NAME: TDP-PX10

FOR HOME OR OFFICE USE

FCC NOTICE:This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and o n, the user is encourage d to try to correct
the interference by one or more of the following measures:

Lamp contains mercury. Disposal of this product may be regulated due to
envi ronmental considerations. For disposal, reuse or recycling information, please
contact your local government or the Electronic Industries Alliance at www.eiae.org.

USA ONLY

Tested To Comply
With FCC Standards

2

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.

- Consult the dealer or an experienced radio/TV technician for help.

RESPONSIBLE PARTY: TOSHIBA AMERICA INFORMATION SYSTEMS, INC.

9740 Irvine Blvd., Irvine, CA 92618-1697 U.S.A
Phone: [phone]

CAUTION: Changes or modifications made to this equipment, not expressly approved by

USA ONLY

Notice: This Class B digital apparatus complies with Canadian ICES-003. Cet appareil

CANADA ONLY

Toshiba, or parties authorized by Toshiba, could void the user’s authority to
operate the equipment.

numérique de la classe B est conforme à la norme NMB-003 du Canada.

Before Using

3

IMPORTANT SAFETY INSTRUCTIONS

CAUTION:PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS

GIVEN IN THIS OWNER'S MANUAL AND THOSE MARKED ON THE UNIT.
RETAIN THIS BOOKLET FOR FUTURE REFERENCE.

This unit is fully transistorized and does not contain any parts that can be repaired by the
user.

WARNING: DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO

DANGEROUS VOLTAGE. REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL ONLY.

1. Read Owner's Manual

After unpacking this product, read the
owner's manual carefully, and follow all
of the operating and other instructions.

2. Power Sources

This product should be operated only
from the type of power source which
does not exceed the voltage range
specified on the rating label and the
power cord. If you are not sure of the
type of power supply to your home,
consult your product dealer or local
power company.

3. Source of Light

Do not look into the lens while the lamp is
on. The strong light from the lamp may
cause damage to your eyesight.

4. Ventilation

Openings in the cabinet are provided for
ventilation and to ensure reliable operation
of the product and protect it from
overheating. These openings must not be
blocked or covered. Never block an
opening by placing the product on a bed,
sofa, rug or other similar surface. Do not
place it in a built-in installation such as a
bookcase or rack, unless proper ventilation
is provided.

4

5. Heat

The product should be situated away
from heat sources such as radiators,
heat registers, stoves, or other
products (including amplifiers) that
produce heat.

6. Water and Moisture

Do not use this product near water.

- for example, near a bath tub, wash
bowl, kitchen sink, or laundry tub; in a
wet basement; or near a swimming
pool and the like.

8. Be sure that you firmly insert
the plug into the wall outlet.

Incorrect or faulty connections may result
in fire or electric shock. Avoid using an
unsound or loose outlet.

9. Power cord protection

Power cords should be routed so that they
are not likely to be walked on or pinched
by items placed upon or against them,
paying particular attention to cords at
plugs, convenience receptacles, and the
point where they exit from the product.

Before Using

7. Cleaning

Unplug this product from the wall outlet
before cleaning. Do not use liquid
cleaners or aerosol cleaners.
Always use a soft cloth for cleaning.

10.Overloading

Do not overload wall outlets. To reduce
the risk of electric shock, do not use the
polarized plug with an extension cord,
receptacle, or other outlet unless the
blades can be inserted completely with
three-wire grounding type to prevent
blade exposure. Failure to follow these
instructions may result in fire or electric
shock.

5

IMPORTANT SAFETY INSTRUCTIONS (Continued)

11.Lightning storms

For added protection for this product
during a storm, or when it is left
unattended and unused for long
periods of time, unplug it from the wall
outlet. This will prevent damage to the
product due to lightning and power­line surges.
Never operate this unit on AC power
during a thunderstorm. If you see
lightning or hear thunder, never touch
the unit, cables and/or peripherals. An
electric surge caused by the storm,
may result in an electrical shock or
damage to the unit.

12.Object and Liquid Entry

Never push objects of any kind into
this product through openings as they
may touch dangerous voltage points
or short-out parts that could result in a
fire or electric shock. Never spill liquid
of any kind on the product.

13.Do not place or keep the
projector within the reach
of the children.

It may fall or tip over, possibly causing
serious injury.

14.Do not place the product
vertically

Do not use the product in the upright
position or any other vertical positions to
project the pictures. It may fall which
could result in serious injury and/or
damage to the product.

15.Stack Inhibited

Do not stack other equipment on this
product and do not place this product on
other equipment. The top and bottom
surface of this product increase in
temperature during normal use and may
damage the other unit.

16.Attachments

Do not use attachments not recommended
by the product manufacturer.
Use of an incompatible attachments could
cause hazards or damage to the product.

6

17.Accessories

Do not place this product on an
unstable cart, stand, tripod, bracket, or
table. The product may fall, causing
serious injury to a child or adult, and
serious damage to the product. A
product and cart combination should
be moved with care. Quick stops,
excessive force, and uneven surfaces
may cause the product and cart
combination to overturn.

S3125A

18.Damage Requiring Service

Unplug this product from the wall
outlet and take the product to qualified
service personnel if you encounter any
of the following conditions:

a) The power supply cord or plug is dam-

aged.

b) Liquid has been spilled, or objects

have fallen into the product.

c) The product has been exposed to rain

or water.

d) The product does not operate

normally when following the operating
instructions. Adjust only those controls
that are covered by the operating
instructions since an improper
adjustment of other controls may
result in damage and will often require
extensive work by a qualified
technician to restore the product to its
normal operation.

e) The product has been dropped or

damaged in any way (If the cabinet
should break, please handle with care to
avoid injury) .

f) The product exhibits a distinct change in

performance, which indicates a need for
service.

19.If glass components, including
lens and lamp, should break,
contact your dealer for repair
service.

This product incorporates glass
components, including a lens and a lamp.
If these should break, please handle with
care to avoid injury and contact your
dealer for repair service. Avoid any
broken pieces of glass since they may
cause injury. In the unlikely event that the
lamp ruptures, thoroughly clean the area
around the projector and discard any
edible items placed in that area since
they may be contaminated.

20.Servicing

Do not attempt to service this product
yourself as opening or removing covers
may expose you to dangerous voltage or
other hazards. Refer all servicing to
qualified service personnel.

Before Using

7

IMPORTANT SAFETY INSTRUCTIONS (Continued)

21.Replacement Parts

When replacement parts are required,
be sure the service technician has
used replacement parts specified by
the manufacturer or have the same
characteristics as the original part.
Unauthorized substitutions may result
in fire, electric shock, or other hazards.
(Only the replacement of the lamp
should be made by users.)

22.Safety Check

Upon completion of any service or
repairs to this product, ask the service
technician to perform safety checks to
verify that the product is in proper
operating condition.

23.Do not leave thermal-paper
documents or easily deformed
items on top of the unit or
near the air exhaust for long
periods of time.

The heat from the unit could erase the
information on the thermal paper, or
cause deformation or warping.

24.Do not use the product in a
closed installation location.

Do not place the product in a box or in
any other closed installation location.
Otherwise it may overheat, which could
result in a risk of fire.

25.Do not look into the laser
light source of the remote
control or direct the laser
pointer toward a person or a
mirror.

The laser beam may cause damage to
your eyesight.

8

IMPORTANT PRECAUTIONS

Moisture Condensation

Never operate this unit immediately after moving it from a cold location to a warm location.
When the unit is exposed to such a change in temperature, moisture may condense on the
lens and the crucial internal parts. Do not use the unit for at least 2 hours when there is an
extreme or sudden change in temperature to prevent the unit from possible damage.

Place and Manner of Installation

• Do not place in hot locations, such as near heating equipment. Doing so could cause
malfunction, and shorten the life of the projector.

• Avoid locations with oil or cigarette smoke. Doing so will dirty the optical parts,
shortening their lives, and darkening the screen.

• Do not use this product in the upright position or tilt it up or down by more than 20° from
level. Doing so may cause a failure or shorten the life of the product.

• Using this instrument near a TV or rad io ma y cau se interfere nce to th e images or audio
sound. If this happens, move it away from the TV or radio.

• Moving the projector from a low-temperature room to a high-temperature room may
cause condensation on the lens or internal parts. If you continue to use it in that
situation, it may malfunction. Wait until the condensation naturally disappears.

• In a high altitude location such as over 600m (2000ft) from sea level, the air is thin and
cooling efficiency is reduced so use the projector with [Fan mode] set to [High].

Otherwise, surface of the projector become hot and the lifetime may be reduced.

• Only plug the power cord into outlets rated for use with the power cord's specified
voltage range. Do not overload extension cords or power strips as this can re sult in fire
or electric shock.

• Route the power cable or the connecting cable away from where people co uld trip over
it. The projector may fall, which could result in severe injury.

• Be sure the power cord is easily reached for unplugging in case of emergency. Do not
place any obstacles near a wall outlet in which the cord is plugged.

p.36

Avoid Volatile Liquid

Do not use volatile liquids, such as an insect spray, near the unit. Do not leave rubber or
plastic products touching the unit for a long time, as they will leave marks on the finish. Do
not use a chemically saturated cloth.

Before Using

9

EXEMPTION CLAUSES

• Toshiba Corporation bears no responsibility in the case of damages arising from natural
disaster such as earthquakes, lightning, etc., fire not liable to Toshiba Corporati on, acts
by third parties, other accidents, or use under abnormal cond itions including erroneous
or improper operation and other problems.

• Toshiba Corporation bears no responsibility for incidental damages (lost profit, work
interruption, corruption or loss of the memory contents, etc.) arising fro m the use of or
the inability to use this unit.

• Toshiba Corporation accepts no liability whatsoever for any damage s arising from not
having followed the descriptions in this Owner's Manual.

• Toshiba Corporation accepts no liability whatsoever for any damages arising from
malfunctions arising from combination with equipment or software that is not related to
Toshiba Corporation.

10

OTHER INFORMATION

Copyrights

Showing or transmitting commercial imaging software or broadcast or cable-broad casting
programs with the purpose of other than the personal and private viewing, including
modifying images using the freeze function, or displaying with the varying aspect ratio of the
images, could violate the direct or indirect copyrights of the imaging software or broadcast
program, etc., if done without first consulting with the copyright holder. For this reason,
please take appropriate measures before performing one of the actions listed above,
including obtaining a license from the copyright holder.

Disposal

This product contains substances which are harmful to humans and the environment.

• The lamp contains mercury.

Please dispose of this product or used lamps in accordance with local regulations.

Following information is only for EU-member states:

The use of the symbol indicates that this product may not be treated as
household waste. By ensuring this product is disposed of correctly, you will
help prevent potential negative consequences for the environment and
human health, which could otherwise be caused by inappropriate waste
handling of this product. For more detailed information about recycling of this
product, please contact your local city office, your household waste disposal
service or the shop where you purchased the product.

Trademarks

• VGA, SVGA, XGA, SXGA, UXGA are trademarks or registered trademarks of
International Business Machines Corporation.

•DLP

• Macintosh is a registered trademark of Apple Computer, Inc.

• Windows is a registered trademark of Microsoft Corporation in the U.S. and other

• Adobe and Acrobat Reader are registered trademarks of Adobe Systems Incorporated.

• All other brand and product names are trademarks or registered trademarks of their

(Digital Light Processing) is a registered trademark of Texas Instruments, Inc.

countries.

respective companies.

Before Using

Notational Conventions Used in This Manual

• References to pages with related information are annotate d as follows. For example, if
making a reference to page 36:

• The illustrations in this document are for reference purposes only and may not reflect
your package exactly.

p.36

11

REMOTE CONTROL BATTERIES

Warning

Never throw batteries into a fire.
Using the batteries improperly may cause them to explode or leak and may result in serious
injury.
If battery-leaking fluid contacts skin, wash the fluid off immediately with clean water and
consult a doctor. If the fluid spills on an instrument, avoid contact and wipe it off using tissue
paper. Then dispose of the used tissue paper as flammable garbage after moistening it with
water.

Notes

• Be sure to use AAA (LR03) size alkaline batteries.

• Dispose of batteries in a designated disposal area.

• Attention should be drawn to the environmental aspects of battery disposal.

• Do not mix different battery types or combine used batteries with new ones.

• If the remote control does not operate correctly, or if the operating range becomes
reduced, replace both batteries with new ones.

• If the batteries are dead or if you will not be using the remote control for a long time,
remove the batteries to prevent bat te r y acid from leaking into the battery compartment.

12

Before Using

13

CONTENTS

Before using

SAFETY PRECAUTIONS ....................................... ... ... ... ... .... ... ... ... .... ......... 2

IMPORTANT SAFETY INSTRUCTIONS ......................... ... .... ... ... ... .... ... ... ... 4

IMPORTANT PRECAUTIONS ......................... ... .... ... ... ... ... .... ... ... ... .... ... ... ... 9

EXEMPTION CLAUSES ............................................................................. 10

OTHER INFORMATION ............... ... .......................................... ... ... .... ... ... . 11

REMOTE CONTROL BATTERIES ............................................................. 12

CONTENTS ................................................................................................ 14

Preparations

Checking the package contents .................................................................. 16

Names of each part on the main unit .......................................................... 17

Names of each part on the control panel and remote control .....................18

Label locations ............................................................................................ 20

Parts on the rear panel ................................................................................ 20

Preparing and using the remote control ...................................................... 21

Operating a computer using the remote control .......................................... 23

Placement ................................................................................................... 24

Connection .................................................................................................. 26

Operations

Turning the power on and off ...................................................................... 28

Basic operations .......................................................................................... 30

Using handy features ....... ... ... ... .... ... ... ....................................... ... ... .... ... ... . 31

Using auto setting (For computer input only) .................................... ... ................31

Correcting the keystone distortion .......................................................................31

Cutting off the picture and sound temporarily (Mute) ...........................................31

Freezing the image (Freeze) ...............................................................................32

Using the menus .............. ... ... ... .... ... ... ... .......................................... .... ... ... . 33

How to use the menus .........................................................................................33

Image adjustment menu ......................................................................................34

Display setting menu ................................. ... .................................... ... ................35

Default setting menu ............................................................................................36

Displaying Information (Status display) ...............................................................37

Using USB Memory ....................... ... ... ... .... ... ... ... ........................................ 38

Maintenance

About lamp .................................................................................................. 42

Lamp replacement ...................................................................................... 42

Lens and main unit cleaning ....................................................................... 45

14

Others

Indicators ................................ ................ ................. ................ ................ .... 46

Before calling service personnel ................................................................. 47

Specifications .............................................................................................. 48

List of general specifications................................................ ... ... .......................... 48

Separately sold product....................................................................................... 48

List of supported signals (RGB signals)............................................................... 49

List of supported signals (Component signals).................................................... 50

Pin assignment of COMPUTER IN terminals ....................................... ............... 51

Pin assignment of S-VIDEO terminals................................................................. 51

Before Using

15

Preparations







Checking the package contents

Please make sure that the following items are included in the box, along with the main unit.If
any item is missing, immediately contact the store where you purchased the product.

(1)

(2)

(3)

 (1) Remote control
 (2) LR03 (SIZE AAA) alkaline batteries for

remote control (2)

 (3) CD-ROM
 (4) Owner’s Manual (This document)

Note

• The shape and number of supplied power cords vary depending on the product
destination.

• To maintain original performance, always use the supplied cables.

(4)

(5)

(6)

 (5) RGB cable (3m)
 (6) Power cord (See note below)
 (7) Carrying bag
 (8) Mouse rem ote control receiver

(7)

(8)

(See note below)

Save Original Packing Materials

The original shipping carton and packing materials will come in handy if you ever have to
ship your projector. For maximum protection when shipping you r projector, repack the set
as it was originally packed at the factory.

The Supplied CD-ROM

The supplied CD-ROM contains an owner's manual, including in formation not available for
the printed Owner's manual (Getting Started) in Portable Document Format (PDF: ) Please
use Acrobat Reader 5 or later version to view the manual.

®

Adobe

The supplied CD-ROM does not contain Acrobat® Reader®. If you cannot read PDF files,
please install Adobe Reader software in your computer by downloading it from the
Adobe Systems website.

Viewing the manual

Run the CD-ROM and double-click on Start.pdf. Acrobat
menu screen of the Owner’s manual appears. Click on your language. The Owner's
Manual cover and list of bookmarks appear. Click on a bookmark title to view that

section of the manual. Click on to view a reference page with related information.
See the Help menu for more information about Acrobat® Reader®.

Acrobat® Reader® or Adobe® Reader

®

®

Reader® launches, and the

16