Toshiba TDP-ET10U User Manual
OWNER’S MANUAL
PROJECTOR
TDP-ET10
TDP-ET20
(with built-in DVD player)
In the spaces provided below, record the Model and Serial Number located at the bottom
of your projector. Retain this information for future reference.
Model No. Serial No.
Others Maintenance Operations Preparations Before Using
SAFETY PRECAUTIONS
The lightning fl ash with arrowhead symbol, within an equilateral triangle, is
intended to alert the user to the presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of suffi cient magnitude to constitute a
risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user
to the presence of important operation and maintenance (servicing) instructions
in the literature accompanying the appliance.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT
WARNING:
USA only
WARNING:
USA only
MODEL NAME: TDP-ET10, TDP-ET20
TRADE NAME: PROJECTOR MODEL NAME: TDP-ET10, TDP-ET20
FOR HOME OR OFFICE USE
FCC NOTICE: This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE. DANGEROUS
HIGH VOLTAGES ARE PRESENT INSIDE THE ENCLOSURE. DO NOT
OPEN THE CABINET. REFER SERVICING TO QUALIFIED PERSONNEL ONLY.
Handling the cord on this product or cords associated with accessories
sold with this product will expose you to lead, a chemical known to the
State of California to cause birth defects or other reproductive harm.
Wash hands after handling.
This product contains mercury. Disposal of mercury may be regulated
due to environmental considerations. For disposal or recycling information, please contact your local authorities or the Electronic Industries
Alliance: www.eiae.org.
USA only
Test ed to C ompl y
With FCC Standards
2
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into and outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
RESPONSIBLE PARTY: TOSHIBA AMERICA INFORMATION SYSTEMS, INC.
9740 Irvine Blvd., Irvine, CA 92618-1697, USA
Phone: (949) 583-3000
WARNING:
USA only
Notice
CANADA only
Changes or modifi cations made to this equipment not expressly
approved by Toshiba, or parties authorized by Toshiba, could void the
user’s authority to operate the equipment.
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.
Before Using
3
IMPORTANT SAFETY INSTRUCTIONS
CAUTION: PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS GIVEN
IN THIS OWNER’S MANUAL AND THOSE MARKED ON THE UNIT. RETAIN
THIS BOOKLET FOR FUTURE REFERENCE.
This set has been designed and manufactured to assure personal safety. Improper use can
result in electric shock or fi re hazard. The safeguards incorporated in this unit will protect you if
you observe the following procedures for installation, use and servicing. This unit is fully transistorized and does not contain any parts that can be repaired by the user.
DO NOT REMOVE THE CABINET COVER OR YOU MAY BE EXPOSED TO DANGEROUS
VOLTAGE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.
1. Read Owner’s Manual
After unpacking this product, read the
owner’s manual carefully, follow all the
operating instructions, and heed all warnings.
2. Power Sources
This product should be operated with
only the type of power source indicated
on the marking label. If you are not sure
what type of power source is available
to you, consult your product dealer and
local power company. For products
intended to operate with battery power or
other power sources, refer to the operating instructions.
3. Source of Light
Do not look into the lens while the lamp
is on. The strong light from the lamp may
cause damage to your eyes or sight.
4. Ventilation
Place this product in a location with adequate ventilation to prevent heat buildup. Openings in the cabinet are provided
for ventilation and must not be blocked
or covered. Do not place this product on
a bed, sofa, rug or other similar surfaces
that may block the ventilation holes. This
product should not be placed in a confi ned space or built-in installation such as
a bookcase or rack unless proper ventilation is provided or the manufacturer’s
instructions have been adhered to.
4
5. Heat
The product should be situated away from
heat sources such as radiators, heat registers, stoves, or other products (including
amplifi ers) that produce heat.
6. Water and Moisture
Do not place this product near water such
as a bathtub, washbowl, kitchen sink,
laundry tub, or in a wet basement, near a
swimming pool and the like. Do not place
objects fi lled with liquids, such as vases
or cups, near or on the product.
8. Power-Cord Protection
Power-supply cords should be routed so
that they are not likely to be walked on or
pinched by items placed upon or against
them, paying particular attention to cords
at plugs, convenience receptacles, and
the point where they exit from the product.
9. Overloading
Do not overload wall outlets, extension
cords, or integral convenience receptacles as this can result in a risk of fi re or
electric shock.
Before Using
7. Cleaning
Unplug this product from the wall outlet
before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a soft cloth
for cleaning.
5
IMPORTANT SAFETY INSTRUCTIONS (Continued)
10. Lightning storms
For added protection for this product,
during a storm or when it is left unattended and unused for long periods of
time, unplug it from the wall outlet. This
will prevent damage to the product due
to lightning and power-line surges.
However, while it is thundering or lightning, do not touch the apparatus and any
connected cable and/or equipment.
This will prevent you from receiving the
electric shock by an electric surge.
11.
Object and Liquid Entry
Never push objects of any kind into this
product through its openings as they
may touch dangerous voltage points or
short-out parts that could result in a fi re
or electric shock. Never spill liquid of any
kind on the product.
12. Do not place the product
vertically
Do not use the product in the upright
position to project the pictures at the
ceiling, or any other vertical positions. It
may fall down and cause damage to the
product.
13. Stack Inhibited
Do not stack other equipment on this
product or place this product on the
other equipment. The top and bottom
of this product radiates heat and may
overheat or cause damage to the other
equipment.
14. Attachments
Do not use attachments not recommended by the product manufacturer as
they may cause hazards.
6
15. Accessories
Do not place this product on an unstable
cart, stand, tripod, bracket, or table. The
product may fall, causing serious injury
to a child or adult, and serious damage
to the product. A product and cart combination should be moved with care. Quick
stops, excessive force, and uneven
surfaces may cause the product and cart
combination to overturn.
S3125A
16.
Damage Requiring Service
Unplug this product from the wall outlet
and refer servicing to qualifi ed service
personnel under the following conditions:
a) When the power-supply cord or plug is
damaged.
b) If liquid has been spilled, or objects have
fallen into the product.
c) If the product has been exposed to rain
or water.
d) If the product does not operate normally
by following the operating instructions.
Adjust only those controls that are covered by the operating instructions as an
improper adjustment of other controls
may result in damage and will often
require extensive work by a qualifi ed
technician to restore the product to its
normal operation.
e) If the product has been dropped or dam-
aged in any way.
f) When the product exhibits a distinct
change in performance - this indicates a
need for service.
17. If glass components, including the lens and lamp,
should break, contact your
dealer for repair service.
This product incorporates glass components, including a lens and a lamp. If
such parts should break, please handle
with care to avoid injury and contact your
dealer for repair service. The broken
pieces of glass may cause injury. In the
unlikely event of the lamp rupturing, thoroughly clean the area around the projector and discard any edible items placed
in that area.
18. Servicing
Do not attempt to service this product
yourself as opening or removing covers
may expose you to dangerous voltage
or other hazards. Refer all servicing to
qualifi ed service personnel.
Before Using
7
IMPORTANT SAFETY INSTRUCTIONS (Continued)
19. Replacement Parts
The user may perform replacement of
the lamp but a service technician should
make all other repairs. When replacement parts are required, be sure the
service technician has used replacement
parts specifi ed by the manufacturer or
have the same characteristics as the
original part. Unauthorized substitutions
may result in fi re, electric shock, or other
hazards.
20. Safety Check
Upon completion of any service or
repairs to this product, ask the service
technician to perform safety checks to
determine that the product is in proper
operating condition.
21. Do not leave thermal-paper
documents or easily deformed items on top of the
unit or near the air exhaust
for long periods of time.
The heat from the unit could erase the information on the thermal paper, or cause
deformation or warping.
22.
Do not use the product in a
closed installation state.
Do not place the product in a box or in
any other closed installation state otherwise it may overheat. This could result
in a risk of fi re.
8
POWER SUPPLY CORD SELECTION
If your line voltage is 220 to 240V, use one of the following types of cable.
Plug
confi guration Plug type
EURO 220 - 240V Australian
UK 220 - 240V Switzerland
Use a 5A fuse which is approved by
ASTA or BSI to BSI362.
Always replace the fuse cover after
changing the fuse.
Line
voltage
Plug
confi guration Plug type
240V
10A
240V
6A
North American
240V
15A
Line
voltage
220 - 240V
220 - 240V
220 - 240V
IMPORTANT PRECAUTIONS
Save Original Packing Materials
The original shipping carton and packing materials will come in handy if you ever have to
ship your projector. For maximum protection, repack the set as it was originally packed at
the factory.
Moisture Condensation
Never operate this unit immediately after moving it from a cold location to a warm loca-
tion. When the unit is exposed to such a change in temperature, moisture may condense
on the crucial internal parts. To prevent the unit from possible damage, do not use the
unit for at least 2 hours when there is an extreme or sudden change in temperature.
Before Using
Location and Installation
• Do not place in hot locations, such as near a heater or in direct sunlight. Doing so could
cause malfunction, and shorten the life of the projector.
• Avoid locations with oil or cigarette smoke, which can affect the quality and useful like of
the product optical parts and darken the screen.
• Do not use the product vertically in any upright position or slantwise in an angle of 20
degrees or more.
• Using this instrument near a TV or radio may cause interference to the images or sound.
If this happens, move it away from the TV or radio.
• In a high altitude location where air is thin, cooling effi ciency is reduced so use it with the
ambient temperature being lowered.
• The set of projector is hot after use. Handle with care.
• Do not use the projector while holding it in your hands or lap.
• Do not use the projector near a power source and the like, or in locations like a ship
or vehicle that are subject to vibration or shock. Doing so may lead to a malfunction or
shorten service life.
9
IMPORTANT PRECAUTIONS (Continued)
Avoid Volatile Liquid
Do not use volatile liquids, such as an insect spray, near the unit. Do not leave rubber or
plastic products touching the unit for a long time. They will leave marks on the fi nish. If
cleaning with a chemically saturated cloth, be sure to follow the product’s precautions.
EXEMPTION CLAUSES
• Toshiba Corporation bears no responsibility in the case of damages arising from natural
disaster such as earthquakes, lightning, etc., fi re not liable to Toshiba Corporation, acts
by third parties, other accidents, or use under abnormal conditions including erroneous or
improper operation and other problems.
• Toshiba Corporation bears no responsibility for incidental damages (lost profi t, work inter-
ruption, corruption or loss of the memory contents, etc.) arising from the use of or the
inability to use this unit.
• Toshiba Corporation accepts no liability whatsoever for any damages arising from not
having followed the descriptions in this Instruction Manual.
• Toshiba Corporation accepts no liability whatsoever for any damages arising from mal-
functions arising from combination with equipment or software that is not related to
Toshiba Corporation.
OTHER CAUTIONS AND INFORMATION
Copyrights
Showing or transmitting commercial imaging software or broadcast or cable-broad casting programs with the purpose of other than the personal and private viewing, including
modifying images using the freeze functions, or displaying with the varying aspect ratio of
the images, could violate the direct or indirect copyrights of the imaging software or broadcast program, etc., if done without fi rst consulting with the copyright holder. For this reason, please take appropriate measures before performing one of the actions listed above,
including obtaining a license from the copyright holder.
Disposal
This product contains substances which are harmful to humans and the environment.
• The lamp contains mercury.
Please dispose of this product or used lamps in accordance with local regulations.
Following information is only for EU-member states:
The use of the symbol indicates that this product may not be treated as
household waste. By ensuring this product is disposed of correctly, you
will help prevent potential negative consequences for the environment and
human health, which could otherwise be caused by inappropriate waste
handling of this product. For more detailed information and recycling of this
product, please contact your local city offi ce, you household waste disposal
service or the shop where you purchased the product.
10
OTHER CAUTIONS AND INFORMATION (Continued)
Trademarks
• VGA, SVGA, XGA, SXGA, UXGA are registered trademarks of International Business
Machines Corporation.
• Digital Light Processing (DLP), Digital Micromirror Device and DMD are registered trade-
marks of Texas Instruments.
• HDMI, the HDMI logo and High-Defi nition Multimedia Interface are trademarks of HDMI
licensing LCC.
• HQV and HQV logo are registered trademarks of Silicon Optix.
• Dolby, Dolby Digital, Pro Logic and Double D symbol are registered trademarks of Dolby
Laboratories.
• DivX and DivX logo are registered trademarks of DivX, Inc.
• Vikuiti and Vikuiti logo are registered trademarks of 3M.
• Kensington, MicroSaver, and ComboSaver are registered trade marks of Kensington
Computer Products Group.
• All other trademarks and registered trademarks are the property of their respective own-
ers.
Notational Conventions Used in This Manual
• References to pages with related information are annotated as follows. For example, if
making a reference to page 36.
• The illustrations in this document are for reference purposes only and may not refl ect your
package exactly.
Surround
• 5.1ch audio output is driven by 6 internal speakers. The sound surrounding effect is dif-
ferent from its ideal case provided by surrounding external speakers.
• This projector with 5.1ch Dolby Digital Consumer Decoder and Dolby Pro Logic II has
been evaluated and approved by Dolby Laboratories.
• This projector is manufactured under license from Dolby Laboratories.
p.36
Before Using
REMOTE CONTROL BATTERIES
• Never throw batteries into a fi re.
• Be sure to use AAA size batteries.
• Attention should be drawn to the environmental aspects of battery disposal.
• Do not mix different battery types or combine used batteries with new ones.
• If the remote control does not operate correctly, or if the operating range becomes re-
duced, replace both batteries with new ones.
• If the batteries are dead or if you will not be using the remote control for a long time,
remove the batteries to prevent battery acid from leaking into the battery compartment.
Using the batteries improperly may cause them to explode or leak and lead to burns or
injury. If battery-leaking fl uid contacts skin, wash the fl uid off immediately with clean water
and consult a doctor. If the fl uid is spilled on an instrument, avoid contact and wipe it off
using a soft cloth or tissue paper. Dispose of the used cloth or tissue paper.
11
NOTES ON DISCS
On handling discs
• Do not touch the playback side of the disc.
DO
Playback side
• Do not attach paper or tape to discs.
DO NOT
On cleaning discs
• Fingerprints and dust on the disc cause picture and sound deterioration. Wipe the disc
from the center outwards with a soft cloth.
Always keep the disc clean.
DO DO NOT
Notes on copyright
The unauthorized recording, use, distribution, or revision of television programs,
videotapes, DVDs, and other materials is
prohibited under the Copyright Laws.
Structure of disc contents
Normally, DVD video discs are divided into
titles, and the titles are sub-divided into chapters. Video CDs and Audio CDs are divided
into tracks.
DVD video disc
DVD video disc
Title 1
Chapter 1
Chapter 2
Video CD/Audio CD
Video CD/Audio CD
Track 1
Track 2 Track 3 Track 4
Chapter 1
Title 1
Chapter 2
Chapter 3
Track 5
• Do not use any type of solvent such as thinner, benzine, commercially available cleaners or antistatic spray for vinyl LPs. It may
damage the disc.
On storing discs
• Do not store discs in a place subject to
direct sunlight or near heat sources.
• Do not store discs in moisture and dust
places such as a bathroom or near a humidifi er.
• Store discs vertically in a case. Stacking
or placing objects on discs outside of their
case may cause warping.
Each title, chapter or track is assigned a
number, which is called “title number”, “chapter number” or “track number” respectively.
There may be discs that do not have these
numbers.
About this owner’s manual
This owner’s manual explains the basic instructions of this unit. Some DVD video discs
are produced in a manner that allows specifi c
or limited operation during playback. As such,
the unit may not respond to all operating
commands. This is not a defect in the unit.
Refer to instruction notes of discs.
12
Notes on region codes
The region code of this unit is set accord-
ing to the location you purchased the unit. If
region codes, which stand for their playable
area, are printed on your DVD video disc and
ALL
you do not fi nd
or region code matches to
your unit, disc playback will not be allowed by
the player. Some DVDs that have no region
code label may still be subject to area restric-
tions and therefore not playable.
On Video CDs
This unit supports Video CDs equipped with
the PBC (Version 2.0) function. (PBC is the
abbreviation of Playback Control.) You can
enjoy two playback variations depending on
types of discs.
• Video CD not equipped with PBC func-
tion (Version 1.1)
Sound and movie can be played on this unit
in the same way as an audio CD.
Playable discs
The following discs are available. DVD-Video, DVD+RW, DVD+R, DVD -RW, DVD-R,
CD-DA, VCD, SVCD, ISO9600, CD-R, and
CD-RW.
Some of these discs may be incompatible.
Be sure to always use only 12 cm discs.
Disc Mark Contents Disc
DVD
video
discs
Video
CDs
Audio
CDs
The foll owing di scs are al so availa ble.
• DVD- R/RW d iscs of DVD vi deo for mat
• CD-R /CD-RW di scs of CD- DA, Video CD, or M P3 forma t
• You cannot p lay discs other than tho se listed ab ove.
• You cannot p lay discs of DV D-R AM, Photo CD, etc., or non
standardized disc s even if they may be labeled as above.
• Some C D-R /RWs cannot be playe d back depen ding on the
recording conditions.
DIGITAL VIDEO
Audio
+
Video
(moving
pictures)
Audio
+
Video
(moving
pictures)
Audio 12 cm A pprox. 74
Maximum
Size
playback
time
12 cm Approx . 4
hours ( single
sided disc)
Approx.
8 hours
(double sided
disc)
12 cm Ap prox . 74
minutes
minutes
Before Using
• Video CD equipped with PBC function
(Version 2.0)
In addition to operation of a Video CD not
equipped with the PBC function, you can
enjoy playback of interactive software with
search function by using the menu displayed
on the screen (Menu Playback). Some of the
functions described in this owner’s manual
may not work with some discs.
Because of problems and errors that can
occur during the creation of DVD software
and/or the manufacture of DVD discs, Toshi-
ba cannot guarantee that this player will play
every feature of every DVD bearing the DVD
logo.
As one of the creators of DVD technology,
Toshiba DVD players are manufactured to
the highest standards of quality and, as a
result, such incompatibilities are very rare.
13
CONTENTS
Before Using
SAFETY PRECAUTIONS ................................................................................................. 2
IMPORTANT SAFETY INSTRUCTIONS .......................................................................... 4
POWER SUPPLY CORD SELECTION ............................................................................. 9
IMPORTANT PRECAUTIONS .......................................................................................... 9
EXEMPTION CLAUSES ................................................................................................. 10
OTHER CAUTIONS AND INFORMATION ...................................................................... 10
REMOTE CONTROL BATTERIES ...................................................................................11
NOTES ON DISCS ......................................................................................................... 12
CONTENTS .................................................................................................................... 14
Preparations
Checking the package contents ...................................................................................... 16
Names of each part on the main unit .............................................................................. 17
Control panel and remote control parts for TDP-ET10 .................................................... 18
Control panel and remote control parts for TDP-ET20 .................................................... 19
Terminal panel .................................................................................................................20
Preparing and using the remote control .......................................................................... 21
Placement ....................................................................................................................... 22
Connection ...................................................................................................................... 24
Operations
Turning the power on and off .......................................................................................... 26
Basic operations ............................................................................................................. 28
TDP-ET20 DVD playback ............................................................................................... 31
About ............................................................................................ 31
Setup the DVD player. ................................................................................................. 31
PASSWORD (For Parental control) ............................................................................. 31
PARENTAL .................................................................................................................. 32
DEFAULT (RESET) ..................................................................................................... 32
®
DivX
VOD ................................................................................................................... 32
PBC setting ................................................................................................................. 33
OSD LANGUAGE ........................................................................................................ 33
AUDIO LANGUAGE .................................................................................................... 33
SUBTITLE LANGUAGE .............................................................................................. 33
MENU LANGUAGE ..................................................................................................... 34
Playing a disc. ............................................................................................................. 34
1. Basic playback ..................................................................................................... 34
2. Playing in fast reverse or fast forward directions ................................................. 36
3. To pause playback (still playback) ........................................................................ 36
14
4. Locating a chapter or track ................................................................................... 36
5. Repeat playback .................................................................................................. 37
6. Random playback ................................................................................................ 37
7. Changing angles .................................................................................................. 37
8. Title selection ....................................................................................................... 37
9. Changing soundtrack language ........................................................................... 38
10. Subtitles ............................................................................................................. 38
11. Display status ..................................................................................................... 38
12. Multimedia fi les on DVD/CD playback ............................................................... 39
Using menus ................................................................................................................... 41
How to use the menus ................................................................................................. 41
Input MENU ................................................................................................................. 42
Picture setting MENU .................................................................................................. 42
Audio setting MENU .................................................................................................... 45
Setup MENU ................................................................................................................ 46
Status display MENU ................................................................................................... 47
Maintenance
About lamp ...................................................................................................................... 49
Lamp replacement .......................................................................................................... 49
Lens and main unit cleaning ........................................................................................... 52
Others
Trouble indications .......................................................................................................... 53
Before calling service personnel ..................................................................................... 54
Specifi cation .................................................................................................................... 56
List of general specifi cations ....................................................................................... 56
Separately sold product
List of supported signals (Y/Pb/Pr signals) .................................................................. 57
List of supported signals (Video, S-Video signals) ...................................................... 57
CONTROL terminal ..................................................................................................... 58
............................................................................................... 56
Before Using
15
Checking the package contents
Check that the following items are included in the box, along with the main unit. If any item
is missing, please contact the store where you purchased the product.
Remote control
(1)
(2)
R03 (size AAA) batteries for
remote control
Owner’s manual (this book)
(3)
(4) Power cord
*2
*1
(5) Scart adapter
*1 Remote shape of TDP-ET10 is different from this fi gure.
*3
p.18
*2 The shape of supplied power cord varies on the product destination.
*3 Scart adapter is not supplied on some product destinations.
16
Names of each part on the main unit
2
4
1
12
5
3
3
11
Front Rear
8
8
6
10D
10C
10A
10B
For more information, see the pages in parentheses.
Name Function
(1) Lens Project expanded image.
(2) Focusing ring Adjust screen focus.
(3) Infrared remote sensor Sense commands from the remote control.
(4) Control panel Adjust the main functions of the projector.
(5) Terminal panel Connect external devices.
(6) Foot adjuster Adjust the vertical projection angle.
(7) Air intake Draw in air from outside the projector.
(8) Air exhaust Expel air that has grown hot inside the projector.
(9) Lamp cover Open for lamp replacement.
(10) Built-in 5.1 speakers Built-in speakers to discrete audio channels.
10A. Center speaker Built-in speaker for center channel sound.
10B. Front speakers Built-in speaker for front channels sound.
10C. Rear speakers Built-in speaker for rear channels sound.
10D. Subwoofer speaker Built-in speaker for subwoofer sound.
(11) Disc slot (for TDP-ET20) Insert DVD or CD disc.
(12) Antitheft lock hole TOSHIBA recommend to use Kensington’s MicroSaver or
ComboSaver for antitheft lock. For detail, please see the
internet web site: www.kensington.com
7
10C
10B
Bottom
p.20
p.50
p.31
p.18
~
9
p.19
Preparations
17
Control panel and remote control parts for TDP-ET10
NEERCS
EZIS
TCIP
U
ER
EDOM
8
[TDP-ET10 Remote]
1
9
8
10
3
11
7
12
13
14
7
6
5
3
4
[TDP-ET10 control panel]
For more information, see the pages in parentheses.
(1) ON/STANDBY: Switch projector between ON and STANDBY.
(2) MENU (INPUT):
Access the main programming menu or select input source.
(3) ENTER : Activate highlighted item in the on screen menu.
(4) DOWN: Move down and highlight the item.
(5) UP: Move up and highlight the item.
(6) + - : Increase / decrease the volume.
(7) PICTURE: Select picture mode.
(8) SCREEN SIZE: Select screen size.
Full , 4:3 , Zoom , Theater Wide .
(9) INPUT SELECT: Select Video, S-Video, YPBPR, Computer, or
HDMI.
(10) : Select or adjust on screen programming menus.
(11) MENU: Access the main programming menu.
(12) Vol +-: Increase / decrease the volume
(13) AUDIO MUTE: Cut of f the sound temporarily.
VIDEO MUTE: Black out the projected image.
(14) FREEZE: Freeze the screen.
p.42
2
p.43
1
p.41
p.41
18
Loading...