TABLE OF CONTENTS
Safety Instructions iii
Introduction 1
Image Resolution 1
Compatibility 1
Unpacking the Projector 1
Usage Guidelines 3
If You Need Assistance 4
Warranty 4
Setting up the Projector 5
Connecting a Computer 7
Connecting a Video Player 9
Powering up the Projector and Adjusting the Image 11
Turning Off the Projector 12
Using the Projector 13
Basic Image Adjustment 13
Using the Remote Control 13
Adjusting the Projector 15
Using the Keypad and Remote Buttons 16
Using the On-Screen Menus 18
Display Menu 19
Audio Menu 20
Image Menu 21
Controls Menu 23
Language Menu
Status Menu 26
25
Maintenance & Troubleshooting 27
Cleaning the Lens 27
Replacing the Projection Lamp 27
Replacing the Batteries in the Remote Control 30
Using the Kensington Lock 30
Troubleshooting 31
i
Ta b l e o f C o n t e n t s
Appendix 35
Specifications 35
Accessories 36
Portable Computer Activation Chart 38
Using Video Mirroring with a PowerBook Computer 43
Projected Image Size 44
Index 45
ii
SAFETY INSTRUCTIONS
Please read and follow all safety instructions provided BEFORE
using your new projector. Failure to comply with safety instructions may result in fire, electrical shock, or personal injury and
may damage or impair protection provided by equipment. Please
save all safety instructions.
Safety Definitions:
•
Warn ing:
Statements identify conditions or practices that
could result in personal injury.
•
Caution:
Statements identify conditions or practices that could
result in damage to your equipment.
Safety Symbols:
Attention:
For information about usage of a feature, please
refer to the User’s Guide.
Hot surface. Do not touch.
Warn ing:
An arrow pointing to the lamp door on the projector.
Safety Terms:
•
Warn ing:
Don’t look directly into the lens when the lamp is
turned on.
•
Warning :
To replace the lamp, turn the projector off by
unplugging the power cord. To avoid burns, wait 30
minutes before opening the lamp door. Follow all instructions
provided in this User’s Guide.
•
Warning :
Please use the power cord provided. Connect
the power cord to a receptacle with a protective safety
(earth) ground terminal.
•
Warn ing:
Refer all service to qualified service personnel. Servicing your own projector will void the warranty. See the following page for the customer service contact information.
•
Caution:
Don’t block ventilation openings.
iii
Safety Instructions
•
Caution:
Don’t set liquids on the projector. Spilled liquids may
damage your projector.
•
Caution:
Don’t place the projector on a hot surface or in direct
sunlight.
•
Caution:
Do not drop the projector. Transport the projector in a
vendor-approved case; refer to your Toshiba dealer or
projectors.toshiba.com
Important Operating Considerations
for more information.
Do not place the projector on a tablecloth or other soft covering
that may block the vents. In the unlikely event of the bulb rupturing, thoroughly clean the area behind the projector and discard
any edible items placed in that area.
)
m
6
.
(
t
f
2
Do not place objects in
this area behind the projector
Customer Service
If you need assistance, contact Toshiba Technical Support.
•
In North America, call Toshiba’s toll-free customer service
& technical support at
800-457-7777
(available 24 hours a
day, 7 days a week).
•
For web-based or other electronic technical support, please
visit Toshiba at
support.toshiba.com
.
iv
INTRODUCTION
®
The Toshiba
TDP-B1™ is specifically designed for the mobile
presenter. It packs XGA 1024x768 graphics with 16.7 million colors into a small, 4.8 pound package. It generates crisp, clear
images using Digital Light Processing™ (DLP) technology. The
TDP-B1 is easy to connect, easy to use, easy to transport, and easy
to maintain.
Image Resolution
The XGA resolution of the TDP-B1’s projected image is 1024x768.
The projector cannot compress screen resolutions above
1024x768. If your computer’s screen resolution is higher than
1024x768, reset it to a lower resolution before you connect the
projector
.
Compatibility
The projector is compatible with a wide variety of computers and
video devices, including:
•
IBM-compatible computers, including portable computers, up
to 1024x768 resolution.
NOTE: The TDP-B1 automatically
expands 640x480 and 800x600
images to 1024x768. You can dis-
play these images at their native
resolutions by turning off the Auto
Resize feature. See “Auto Resize”
on page 21 for more information.
•
Apple Macintosh and PowerBook computers up to 1024x768
resolution.
•
Most standard VCRs, DVD players, camcorders and laser disc
players.
Unpacking the Projector
The projector comes with the items shown in Figure 1. Check to
make sure all are included.
diately if anything is missing
Contact your Toshiba dealer imme-
.
If you are experienced in setting up presentation systems, use the
Quick Start
card that was included in the shipping box. For complete details on connecting and operating the projector, refer to
this User’s Guide. User’s Guides are also available for download
from our website at
projectors.toshiba.com
.
1
Introduction
NOTE: The contents of your
shipping box may vary depending
on the projector configuration
you’ve ordered.
1
2
3
5
8
6
7
10
9
F
IGURE 1
Shipping box contents
1. TDP-B1 projector + lens cap 6. Audio cable adapter
2. Remote control 7. Audio cable
3. Power cord 8. Composite video cable
4. User’s Guide and quick start
9. PS/2 mouse cable
card
5. VESA computer cable 10. USB mouse cable
4
2
zoom ring
speaker
keyp ad
Kensington Lock
focus ring
connector panel
power
cord
connector
FIGURE 2
Side view of projector
Usage Guidelines
•
Do not look directly into the projection lens when the lamp is
turned on. The bright light may harm your eyes.
•
Do not block the grills on the projector. Restricting the air flow
can cause it to overheat and turn off. If this happens, you must
wait a minute before attempting to turn it back on.
•
Handle the projector as you would any product with glass
components. Be especially careful not to drop it.
•
Avoid leaving the projector in direct sunlight or extreme cold
for extended periods of time. If this happens, allow it to reach
room temperature before use.
•
Transport the projector in a vendor-approved hard or soft case.
Refer to your Toshiba dealer or
projectors.toshiba.com
for more
information.
3
Introduction
If You Need Assistance
The first place to look for help is in this manual. Be sure to check
the guidelines in “Troubleshooting” on page 31. Or, check the
Service and Support section of our website at
support.toshiba.com.
If those sources don’t answer your question, call your Toshiba
dealer. You can also call Toshiba Technical Support directly.
•
•
Warranty
This product is backed by a limited two-year warranty. The
details of the warranty are printed at the back of this manual. A
longer term warranty can be purchased from your Toshiba dealer.
Refer to your Toshiba dealer or
information.
In North America, call Toshiba’s toll-free customer service
& technical support at
800-457-7777
(available 24 hours a
day, 7 days a week).
For web-based or other electronic technical support, please
visit Toshiba at
support.toshiba.com
support.toshiba.com
.
.
for more
4
SETTING UP THE PROJECTOR
Place the projector on a flat surface.
1
•
The projector must be within 10 feet (3 m) of your power
source and within 6 feet (1.8 m) of your computer.
•
If you want to project from behind a translucent screen, set
up the projector behind your screen. See “Rear Projection”
on page 24 to reverse the image.
Position the projector the desired distance from the screen.
2
•
The distance from the lens of the projector to the screen and
the zoom setting determine the size of the projected image.
Figure 3 shows three projected image sizes. For more information about image size, see “Projected Image Size” on
page 44.
1
3
.
0
f
t
.
7
.
8
3
f
.
t
2
.
f
t
.
5 ft
12 ft.
.
20 ft.
F
Projected image size at minimum zoom
Make sure the projector is unplugged and your computer is
3
turned off.
IGURE
3
5
Setting up the Projector
NOTE: Before you continue,
make sure the projector is
unplugged and your equipment is
turned off. If you’re connecting a
computer, make sure the distance
between it and the projector is 6
feet or less.
F
IGURE 4
S-video
composite
video
Audio in
mouse
VESA computer
input
Connector panel
6
Connecting a Computer
Plug one end of the VESA computer cable into the video con-
1
nector on your computer.
Plug the other end of the VESA computer cable into the
2
connector on the projector.
audio cable
VESA cable
Connecting the projector to a computer
Do you want to play your computer’s audio on the projector?
Plug either end of the audio cable into the audio connector on
1
your computer.
FIGURE 5
NOTE: Many portable computers
do not automatically turn on their
external video port when a sec-
ondary display device such as a
projector is connected. Refer to
your computer manual for the
command that activates the exter-
nal video port. Activation com-
mands for some portable
computers are listed in the Appen-
dix of this manual on page 38 or
visit support.toshiba.com for
more information.
Plug the other end of the audio cable into the connector
2
on the projector.
NOTE: If you are connecting an
older Macintosh computer that
does not have a 15-pin connector,
you must use a Mac adaptor
between the computer and the
projector. See “Optional Accesso-
ries” on page 37.
7
Setting up the Projector
Do you want to control the computer’s mouse from the projector’s
remote or keypad?
If your computer has a PS/2 connector, use the PS/2 mouse cable.
Plug the end of the PS/2 mouse cable with 6 pins into the
1
mouse connector on your computer.
Plug the end of the PS/2 mouse cable with 9 pins into the
2
connector on the projector.
If your computer has a USB connector and is running Windows 98,
use the USB mouse cable.
Plug the end of the USB mouse cable into the
1
NOTE: The USB mouse is
supported for use with
Windows 98 only.
mouse connector on your computer.
Plug the end of the USB mouse cable into the connector
2
on the projector.
You must have the appropriate USB drivers installed on your
computer to use the USB feature. Windows 98 ships with the
appropriate drivers.
NOTE: You do not need to restart
your computer after connecting a
USB mouse to use it (it is hot-
pluggable). You must restart your
computer after plugging in a PS-2
mouse.
8
Now you’re ready to power up the projector and your computer.
Skip to “Powering up the Projector and Adjusting the Image” on
page 11.
Connecting a Video Player
If your video player uses a round, one-prong composite video
1
connector, you’ll need only the audio cable, audio adapter,
and composite video cable that shipped with the projector.
•
If your video player uses a round, four-prong S-video connector, you’ll need an S-video cable in addition to the audio
cable and audio adapter. The S-video cable is sold separately. (See “Optional Accessories” on page 37.)
Plug the composite video cable’s yellow connector into the
2
“video-out” connector on your video player (Figure 6). This
connector may be labeled “To Monitor.”
•
If you’re using an S-video cable, connect it to the “S-video
out” connector on the video player (Figure 7).
Plug the other yellow connector into the composite video con-
3
nector
•
If you’re using S-video, plug the other end of the cable into
the “S-video” connector
on the projector.
on the projector (Figure 7).
audio
adapter
composite video cable
audio cable
F
IGURE
Connecting the projector to a video player using the standard video cable (with com-
posite video connector) and the audio cable and adapter
6
9
Setting up the Projector
NOTE: The audio adapter is
provided so that the same audio
cable used to connect a computer
can be used with the adapter to
connect a VCR.
audio
adapter
F
IGURE 7
Connecting the projector to a video player using an S-video cable and the audio cable
and adapter
Plug the audio adapter’s white connector into the left “audio
4
S-video
cable
audio cable
out” connector on your video player. Plug the adapter’s red
connector into the right “audio out” connector on the video
player (Figure 6 and Figure 7).
Plug the audio adapter’s other end into the audio cable.
5
Plug the audio cable into the “audio in” connector on the
6
projector.
The projector is compatible with these major broadcast video
standards: NTSC, NTSC 4.43, PAL, PAL-M, PAL-N, and SECAM.
It automatically adjusts to optimize its performance for the
incoming video. See “Video Standard” on page 23 for details.
CAUTION: Your video player
may also have a “Video Out”
connector for a coaxial cable
connection. DO NOT use this to
connect to the projector.
10
Powering up the Projector and Adjusting the Image
Remove the lens cap.
1
Plug the power cord into the side of the projector, then plug it
2
into your electrical outlet. A surge-protected power strip is
recommended.
•
The fans start to run, and the Lamp LED on the top of the
projector (Figure 11 on page 16) lights orange until the software has initialized. When initialization is complete, the
Lamp LED lights green. A green Lamp LED indicates that
you can press the
lamp on/off
button to turn the lamp on
and off.
NOTE: Always use the power cord
that shipped with the projector.
Turn on the lamp by pressing the
3
lamp on/off
button on
the keypad (see Figure 11 on page 16).
•
The startup screen appears.
If you connected a video player, turn it on.
4
•
The video image should display on the projection screen. If
a computer source is active, press the
keypad (page 16) or the
button on the remote to dis-
video
button on the
source
play your video image. You can select a default source to
determine which source the projector examines first during
power-up for active video; see “Default Source” on page 24.
•
Use the
Turn on your computer.
5
•
The computer image should display on the projection
volume
screen. If a video source is active, press the
the keypad or the
buttons to adjust the volume.
source
computer
button on the remote to display
your computer’s image. Make sure your computer’s external video port is activated; see “Portable Computer Activation Chart” on page 38 for details.
•
If necessary, make adjustments to the image using the projector’s on-screen menus. To open the menus, press the
button on the keypad or remote, then select the Dis-
menu
play or Image sub-menu. For more information about the
menus, see page 18.
button on
NOTE: With some computers,
the order in which you power up
the equipment is very important.
Most computers should be turned
on last, after all other peripherals
have been turned on. Refer to your
computer’s documentation to
determine the correct order.
11
Setting up the Projector
Turning Off the Projector
If you want to turn off the projector for a short period of time,
press the
standby
button on the keypad or remote. This blanks the
screen for fifteen minutes, but keeps the projector running. (You
can change the amount of time the projector stays in standby
mode; see “Standby Time” on page 23 for details.) After 15 minutes, the lamp goes out (the projector keeps running). To exit
standby mode, press the
standby
button again. (It may take several seconds for the projection lamp to reach full power and
project the image again.)
To completely power off the projector, unplug it. If you want to
NOTE: Lamp life will be extended
if you turn the lamp off, then wait
1 minute while the lamp cools
before unplugging the projector.
The Lamp LED will light green
when the lamp has cooled. See
page 16 for details on the Lamp
LED.
turn the lamp back on immediately, you must allow about a
minute for the lamp to cool. The lamp won’t light if it’s too hot.
12
USING THE PROJECTOR
This section describes how to use and make adjustments to the
projector. It also provides a reference to the keypad and remote
buttons and the options available from the on-screen menus.
Basic Image Adjustment
Make sure you have powered up your equipment in the right
1
order (page 11).
If the image doesn’t display completely, zoom the image
2
(page 15), adjust the height of the projector (page 15) or center
the image by adjusting its horizontal or vertical position
(page 22). Be sure the projector is at a 90 degree angle to the
screen.
If the image is out of focus, rotate the focus lens (page 15).
3
If the image appears to shimmer or if it has blurry vertical
4
bars after you have adjusted the focus, turn Auto Image
(page 21) off and then back on to reset the automatic sync and
tracking. If that doesn’t clear up the image, turn Auto Image
off and adjust the sync (page 21) and/or the tracking
(page 22) manually.
If the colors don’t look right, adjust the brightness (page 19).
5
Using the Remote Control
The projector ships with a remote that has four function buttons,
a disk mouse and two mouse buttons, one on the top of the
remote and one on the bottom.
Point the remote control at the projection screen or at the front of
the projector. The range for optimum operation is about 25 feet. If
you point the remote at the projection screen, the distance to the
screen and back to the projector must be less than or equal to 25
feet. For best results, point the remote directly at the projector.
NOTE: To control the computer’s
mouse from the projector’s remote
or keypad, you must connect a
mouse cable to the projector and
the computer. See page 8 for
details.
13
Using the Projector
left mouse button
(on underside of remote)
FIGURE 8
Remote control
disk mouse
right mouse button
NOTE: If the remote is inactive
for several minutes, it “sleeps” to
conserve battery life. Press any
button except the disk mouse to
re-activate the remote.
Press anywhere on the edge of the disk mouse to move the cursor
on the screen. You can move the cursor at any angle by pressing
the corresponding edge of the disk. The mouse button on the top
of the remote simulates your computer’s right mouse button; the
button on the bottom simulates your computer’s left mouse button. See “Using the Keypad and Remote Buttons” starting on
page 16 for a description of the four function buttons.
®
If you are creating presentations in Microsoft
PowerPoint®, you
can use the remote’s mouse buttons to navigate through your
presentation while in Slide Show mode. To configure PowerPoint
for this, choose Options from the Tools menu, click the View Tab,
de-select the “Popup Menu on Right Mouse Click” option in the
Slide Show section, then click OK. Then, when you’re in PowerPoint’s Slide Show mode, a left click advances to the next slide
and a right click returns to the previous slide (other PowerPoint
modes are not affected).
14
Adjusting the Projector
To focus the image, rotate the focus ring (Figure 9) until the image
is clear. To zoom the image, rotate the zoom ring. This adjusts the
image size without affecting focus.
zoom ring
focus ring
FIGURE 9
Focus ring and zoom ring
The projector is equipped with a self-locking, quick-release elevator foot and button (Figure 10).
To raise the projector:
Press and hold the elevator button (Figure 10).
1
Raise the projector to the height you want, then release the
2
button to lock the elevator foot into position.
elevator button
(under finger)
elevator foot
FIGURE 10
Adjusting the height of the projector
15
Using the Projector
Using the Keypad and Remote Buttons
While the menus are displayed, the volume, source, and standby
buttons on the keypad act as menu navigation buttons. See
“Using the On-Screen Menus” on page 18 for details.
lamp LED
FIGURE 11
Keypad and remote buttons
16
Lamp on/off (keypad only)
Press the
lamp on/off
button to turn the lamp on or off. The Lamp
LED indicates the state of the lamp. A green Lamp LED indicates
that you can turn the lamp on, or the lamp is currently on. An
orange LED indicates the software is initializing or the lamp is
cooling. Do not press the
lamp on/off
button when the LED is
orange.
Menu
Press the
button to open the on-screen menus. Press
menu
menu
again to close the menus. When you close the menus, the projector saves any changes you made. For more information about the
on-screen menus, see page 18.
Source (keypad only) or Computer and Video (remote only)
When you have more than one source (computer and video) connected to the projector, select between them by pressing the
button on the keypad or the
source
computer
or
video
button on
the remote.
Standby
When you press
standby
, the display and audio turn off and a
blank screen is displayed for 15 minutes. You can change the
amount of time the projector stays in standby mode; see
“Standby Time” on page 23 for details.
•
If you press
standby
again within 15 minutes, the projector
returns to normal operations immediately.
•
If you press
standby
again after 15 minutes, there is about a
60 second delay before the lamp turns back on.
•
If you don’t press
standby
again, the lamp turns off after 15
minutes.
Volume (keypad only)
To increase the volume, press
ume, press
volume - .
volume + .
To decrease the vol-
Volume adjustments are saved for each source you have connected.
17
Using the Projector
Using the On-Screen Menus
The projector
has six drop-down menus that allow you to make
image adjustments and change a variety of settings. Most of these
adjustments aren’t available directly from the keypad.
NOTE: Some menu items may be
grayed out at certain times. This
indicates the item is not applicable
to your setup (for example, video
standards do not apply to
computer sources) or the item is
not enabled until another selection
is made (for example, Manual
Tracking is not available until Auto
Image is turned off).
To open the on-screen menus, press the
button on the
menu
keypad or remote. This changes the volume, source, and standby
buttons on the keypad to menu navigation buttons. Press the
corresponding buttons to move the cursor up, down, left, or
right, or use the disk mouse on the remote. To select a menu,
move the cursor left and right to highlight the menu you want.
The drop-down menu appears.
use these buttons to navigate through
the menus
FIGURE 12
Keypad navigation buttons and drop-down menu
18
To change a menu setting, use the up and down navigation buttons on the keypad or the disk mouse on the remote to move the
cursor up and down to the item you want to change (the selected
item is highlighted), then use the left and right navigation buttons to adjust a setting. Some submenus, such as Brightness, consist of a slider bar you use to increase or decrease a value; some
submenus, such as Standby Time, consist of options you scroll
through to select the desired one. All changes are saved when
you close the menus.
To access another menu, use the up and down navigation buttons
or the disk mouse to move back to the top of the current menu,
then use the left and right navigation buttons to move to another
menu.
Display Menu
FIGURE 13
Display menu
Brightness
Adjusting the brightness changes the intensity of the image.
•
Press the left navigation button to darken the image.
•
Press the right navigation button to lighten the image.
Contrast
The contrast controls the degree of difference between the lightest
and darkest parts of the picture. Adjusting the contrast changes
the amount of black and white in the image.
•
Press the left navigation button to decrease the contrast.
•
Press the right navigation button to increase the contrast, making the blacks appear blacker and the whites appear whiter.
Tint
The tint adjusts the red-green color balance in the projected
image. Changing the Tint setting has no effect on PAL or SECAM
video sources.
•
Press the left navigation button to increase the amount of green
in the image.
•
Press the right navigation button to increase the amount of red
in the image.
19
Using the Projector
Color
The color setting adjusts a video image from black and white to
fully saturated color.
•
Press the left mouse button to decrease the amount of color in
the image.
•
Press the right mouse button to increase the amount of color in
the image.
Blank Screen
Blank Screen determines what color is displayed when there is no
active source and when the projector is in standby. Click the left
or right navigation button to toggle between blue and black.
Reset All
Click the left or right navigation button to reset all the options
(except Language, Video Standard, Rear Projection, and Standby
Time) in all the menus to their original settings.
Audio Menu
NOTE: Changing the volume
using the menu is the same as
changing it using the keypad.
20
FIGURE 14
Audio menu
Vo lu me
•
Press the left navigation button to decrease the volume.
•
Press the right navigation button to increase the volume.
Volume adjustments you make are saved for each source.
Image Menu
FIGURE 15
Image menu
Auto Image
The projector automatically adjusts tracking, signal synchronization and vertical and horizontal position for most computers
(Auto Image does not apply to video sources). If you want to
adjust these features manually, you must turn off
Auto Image
first
by highlighting Auto Image in the Image menu and clicking the
left or right navigation button to select “off”.
Auto Resize
Auto Resize
automatically resizes the image by scaling it up. It
only affects computer images that are not the projector’s native
resolution.
NOTE: Some screen savers inter-
fere with the operation of Auto
Image. If you’re experiencing prob-
lems, try turning your screen saver
off, then turning Auto Image off
and back on.
When
Auto Resize
image to the computer screen. If you turn
is on, the projector makes the best fit of the
Auto Resize
off (by
highlighting it in the Image menu and clicking the left or right
navigation button to select “off”), the image may be either
cropped or too small for the screen.
Manual Sync
The projector adjusts signal synchronization automatically for
most computers. But if the projected computer image looks fuzzy
or streaked, try turning
Auto Image
off then back on again. If the
image still looks bad, try adjusting the signal synchronization
manually:
21
Using the Projector
Turn Au to Im ag e o ff .
1
Highlight Manual sync, then press the left or right navigation
2
button repeatedly until the image is sharp and free of streaks.
Manual Tracking
The projector adjusts tracking automatically to match the video
signal from your computer. However, if the display shows evenly
spaced, fuzzy, vertical lines or if the projected image is too wide
or too narrow for the screen, try turning
on again. If the image is still bad, try adjusting the tracking manually:
Turn Au to Im ag e o ff .
1
NOTE: The Manual Sync ,
Manual Tracking, Horiz.
Position and Ve r t . P o sitio n
options are available only for
computer sources. The projector
sets these options automatically
for video sources.
Highlight Manual tracking, then press the left or right naviga-
2
tion button repeatedly until the fuzzy vertical bars are gone.
Horizontal position
Follow these steps to manually adjust the horizontal position:
Turn Au to Im ag e o ff .
1
Highlight Horizontal position, then press the left navigation
2
button to move the image right or press the right navigation
button to move the image left.
Auto Image
off then back
22
Positioning adjustments are saved when you power off the projector.
Ver t i c a l p o s it i o n
Follow these steps to manually adjust the vertical position.
Turn Au to Im ag e o ff .
1
Highlight Vertical position, then press the left navigation but-
2
ton to move the image down or press the right navigation button to move the image up.
Positioning adjustments are saved when you power off the projector.
Controls Menu
FIGURE 16
Controls menu
Video Standard
When Video standard is set to Auto, the projector attempts to
pick the video standard (NTSC, NTSC 4.43, PAL, PAL-M, PAL-N,
or SECAM) automatically based on the input signal it receives.
(The video standard options may vary depending on your region
of the world.) If the projector is unable to detect the correct standard, the colors might not look right or the image might appear
“torn.” If this happens, manually select a standard by clicking the
left or right navigation button and cycling through the standards.
NOTE: If you already know the
video standard used in your geo-
graphical area, it’s often best to
manually select it.
Standby Time
This option lets you select how long the lamp stays on and the
blank screen is displayed when the projector enters standby
mode before the projector turns off. Select among 1, 5, 10, and 15
minutes and 1 and 2 hours by clicking the left or right navigation
button and cycling through the options.
23
Using the Projector
Rear Projection
When you turn
Rear Projection
image so you can project from behind a translucent screen. Highlight Rear Projection, then click the left or right navigation button
to turn this feature on and off.
Default Source
Default Source toggles between Computer and Video. This determines which source the projector checks first for active video
during power-up. Highlight Default Source and click the left or
right navigation button to toggle between the options.
Auto Source Select
This setting toggles between On and Off. When this feature is Off,
the projector defaults to the source selected in Default Source. To
display another source, you must manually select one by pressing the
button on the keypad or the
source
ton on the remote. When this feature is On, the projector
automatically finds the active source, checking the default source
first. Highlight Auto Source Select and click the left or right navigation button to turn this feature on and off.
on, the projector reverses the
computer
or
video
but-
24
Plug and Play
This setting toggles between On and Off. When it is On, most
new computers will automatically recognize the projector, then
set the monitor resolution and refresh rate accordingly. You need
to set the Plug and Play setting to Off for the projector to display
properly on some older computers. The Plug and Play setting
does not affect video images.
If the projector’s display constantly changes between the computer image and the message, “Perfecting the image”, you may
need to turn Plug and Play Off.
Display Messages
This setting toggles between On and Off. When this feature is On,
status messages such as “No signal detected” or “Standby
Active” appear in the lower-right corner of the screen. Click the
left or right navigation button to turn this feature off and not see
status messages.
Display Startup Screen
This setting toggles between On and Off. When this feature is On,
the startup screen appears when the projector starts up and
remains until an active source is detected. Click the left or right
navigation button to turn this feature off and display a plain
black or blue screen instead of the startup screen.
Language Menu
FIGURE 17
Language menu
You can display the on-screen menus in English, French, German,
and Spanish.
•
Move the cursor to the language you want, then click the left or
right navigation button. The menus redraw immediately.
25
Using the Projector
Status Menu
This is a read-only window for informational purposes. To display the status window, select Show status from the menu, then
click the left or right navigation button. To remove the window,
click the left or right navigation button.
FIGURE 18
Status menu
26
Lamp hours used
Indicates how many hours the current lamp has been in use. The
counter starts at zero hours and counts each hour the lamp is in
use. Change the bulb when the brightness is no longer acceptable. See “Replacing the Projection Lamp” on page 27 for details.
Computer resolution
Shows your computer’s resolution setting. To change this, go to
your computer’s Control Panel and adjust the resolution in the
Display tab. See your computer’s user’s guide for details.
Horizontal refresh rate
The time period that one horizontal line is displayed.
Ver t i c a l r e f r e s h r a t e
The time period that one video frame is displayed.
Mute status
Indicates if the audio is muted.
Software version
Indicates the projector’s software version. This information is
useful when contacting Technical Support.
Source
Indicates the active source, Computer or Video.
MAINTENANCE & TROUBLESHOOTING
This section describes how to:
•
clean the lens
•
replace the projection lamp
•
replace the batteries in the remote
•
use the Kensington lock feature
•
troubleshoot the projector
Cleaning the Lens
Follow these steps to clean the projection lens:
Apply a non-abrasive camera lens cleaner to a soft, dry cloth.
1
•
Avoid using an excessive amount of cleaner.
•
Abrasive cleaners, solvents or other harsh chemicals might
scratch the lens.
Lightly wipe the cleaning cloth over the lens in a circular
2
motion.
If you don’t intend to use the projector immediately, replace
3
the lens cap.
Replacing the Projection Lamp
The lamp hour counter in the Status menu counts the number of
hours the lamp has been in use. Replace the lamp when the
brightness is no longer acceptable. You can order new lamp modules from your Toshiba dealer. See “Accessories” on page 36 for
information. In the unlikely event of a lamp rupture, please contact your Toshiba dealer.
Follow these steps to replace the projection lamp:
Turn off the projector by unplugging the power cord.
1
Wait 30 minutes to allow the projector to cool thoroughly.
2
Invert the projector on a flat surface, then insert a small screw-
3
driver or other flat object into the tab on the lamp module
door (Figure 19).
WARNING: To avoid burns,
allow the projector to cool for at
least 30 minutes before you open
the lamp module door. Never
extract the lamp module while the
lamp is operating.
27
Maintenance & Troubleshooting
Pull the lamp door up and remove it.
4
WARNING: Be extremely careful
when removing the lamp module.
In the unlikely event that the bulb
ruptures, please contact your
Toshiba dealer, as small glass
fragments may be generated. The
lamp module is designed to
contain these fragments, but use
caution when removing the lamp
module.
CAUTION: Never operate the
projector with the lamp door open
or removed. This disrupts the air
flow and causes the projector to
overheat.
F
IGURE 19
Removing the lamp door
Loosen the two non-removable screws on the outside of the
5
module.
28
F
20
IGURE
Loosening the screws on the lamp module
Lift and grasp the pull tab and lift the module out (Figure 21).
6
pull tab
FIGURE 21
Removing the lamp module
Install the new lamp module, being sure to align the connec-
7
tors properly.
Push the module in until it is flush with the bottom case of the
8
projector.
Tighten the screws on the outside of the module.
9
WARNING: Do not drop the
lamp module or touch the glass
bulb! The glass may shatter and
cause injury.
Replace the lamp door by inserting the hooks on the rear of
10
the lamp door into the projector and pressing the lamp door
into place. If the lamp door does not fit properly or bulges out,
remove the door and re-seat the lamp module.
Plug in the power cord to turn the projector back on.
11
To reset the lamp hour counter in the Status window, press
12
and hold the
volume -
(while still holding down the
button, then press the
volume -
button) for 5 seconds.
Verify that the counter was reset by pressing the
menu
button
menu
and viewing the counter in the Status window.
button
29
Maintenance & Troubleshooting
Replacing the Batteries in the Remote Control
The life of the batteries depends on how often and how long you
use the remote. Symptoms of low battery charge include erratic
responses when using the remote and a reduced range of operation.
Follow these steps to replace the batteries:
Turn the remote face down in your hand.
1
Slide the battery cover off the end of the remote.
2
Remove the old batteries and dispose of them in an environ-
3
mentally proper manner.
Install two new AAA alkaline batteries. Make sure you install
4
each in the correct direction.
Slide the battery cover back on the remote.
5
Using the Kensington Lock
The projector has a Kensington Security Standard connector for
use with a Kensington MicroSaver Security System (Figure 22).
See “Optional Accessories” on page 37 for ordering information.
Refer to the information that came with the Kensington System
for instructions on how to use it to secure the projector.
30
F
22
IGURE
Installing the Kensington lock
Troubleshooting
Problem: Nothing on projection screen
•
Make sure that the power cord is properly connected to a fully
functional AC electrical outlet. Make sure that the power cord
is also properly connected to the projector.
•
If the projector is plugged into a power strip, make sure the
power strip is turned on.
•
Make sure you have removed the lens cap on the projection
lens at the front of the projector.
•
Make sure the lamp is switched on.
•
Check the projector’s lamp to ensure that it is securely con-
nected in the lamp module. See “Replacing the Projection
Lamp” on page 27.
•
Make sure that the cables do not have any bent pins.
Problem: Color or text not being projected
•
You might need to adjust the brightness up or down until the
text is visible. Refer to “Brightness” on page 19 for more information.
Problem: The screen resolution is not right
•
Make sure the computer’s video card is set for a resolution of
no greater than 1024x768.
Problem: Image isn’t centered on the screen
•
Move the projector to reposition the image.
•
Reposition the image using the software. Refer to “Horizontal
position” on page 22 and “Vertical position” on page 22.
•
Be sure the projector is at a 90 degree angle to the screen.
Problem: Only the start-up screen displays
•
Verify that the cables are connected correctly. See page 7
through page 8 for connection procedures.
•
Verify that the proper input source is connected. See “Source
(keypad only) or Computer and Video (remote only)” on
page 16.
31
Maintenance & Troubleshooting
•
You might need to turn everything off and power up the
equipment again in the proper order. Refer to your computer’s documentation to determine the correct order.
•
Make sure your computer’s external video port is turned on.
See the “Portable Computer Activation Chart” on page 38 or
your computer’s manual for details.
•
Make sure your computer’s video board is installed and con-
figured correctly.
•
Make sure your computer has a compatible video board. The
projector isn’t CGA, EGA or SXGA compatible.
If you’re using Windows 98:
Open “My Computer” icon, the Control Panel folder and
1
then the Display icon.
Click the Settings tab.
2
Verify that the Desktop area is set to 1024x768 or less.
3
Problem: Image is too wide or narrow for screen
•
Adjust the zoom or projector placement.
•
Adjust the resolution of your video card if it’s greater than
1024x768.
32
Problem: Image is out of focus
•
Turn the projection lens to focus the image.
•
Make sure the projection screen is at least 5 feet (1.5 m) from
the projector.
•
Check the projection lens to see if it needs cleaning.
Problem: Image and menus are reversed left to right
•
Rear projection mode is probably turned on. Turn Rear Projec-
tion off in the Controls menu. The image should immediately
return to forward projection. See “Rear Projection” on
page 24.
Problem: the projector displays vertical lines, “bleeding” or
spots
•
Adjust the brightness. See “Brightness” on page 19.
•
Check the projection lens to see if it needs cleaning.
Problem: no sound
•
Adjust volume.
•
Verify audio/input connections.
•
Adjust audio source.
Problem: Image is “noisy” or streaked
Try these steps in this order.
Deactivate the screen saver on your computer.
1
2
Tu rn
Auto Image
off and then back on again. See “Auto
Image” on page 21.
3
Tu rn
Auto Image
off and adjust the synchronization and tracking manually to find an optimal setting. See “Manual Sync”
on page 21 and “Manual Tracking” on page 22.
•
The problem could be with your computer’s video card. If
possible, connect a different computer.
33
Maintenance & Troubleshooting
Problem: Projected colors don’t match the computer or video
player’s colors
•
Just as there are differences in the displays of different moni-
tors, there are often differences between the computer image
and the projected image. Adjust the brightness, tint and/or
contrast from the Display menu. See “Brightness” on page 19,
“Tint” on page 19 and “Contrast” on page 19.
Problem: Lamp seems to be getting dimmer
•
The lamp begins to lose brightness when it has been in use for
a long time. Replace the lamp as described in “Replacing the
Projection Lamp” on page 27.
Problem: Lamp shuts off
•
A minor power surge may cause the lamp to shut off. Unplug
the projector, wait at least a minute, then plug it back in.
•
Make sure the vents are not blocked.
The most current troubleshooting information (including webbased and other electronic technical support) is available at
Toshiba’s Service and Support website at
support.toshiba.com.
Before calling your dealer or Toshiba toll-free customer service
and technical support for assistance, please have the following
information available:
•
the projector’s serial number
•
the resolution of your computer.
In North America, call Toshiba’s toll-free customer service &
technical support at
800-457-7777
(available 24 hours a day, 7 days
a week).
For web-based or other electronic technical support, please visit
Tosh ib a a t
support.toshiba.com
.
34
APPENDIX
Specifications
The TDP-B1 must be operated and stored within the temperature
and humidity ranges specified.
Te m p e r a t u r e
Operating
Non-operating
Humidity
Operating and non-oper. 5% to 95% relative humidity, non-condensing
Dimensions
8.75 x 9.75 x 2.5 inches (22.2 x 24.8 x 6.4 cm)
We ig h t
4.8 lbs. (2.2 kg) unpacked
Altitude
Operating 0 to 10,000 feet (3,048 meters)
Non-operating 0 to 40,000 feet (12,192 meters)
50 to 104
-4 to 158
°
F (10 to 40° C)
°
F (-20 to 70° C)
Optics
Focus Range 4.9 - 16 feet (1.5-5 m)
Lamp
Type 120-watt VHP lamp
Input Power Requirements
100-120VAC 6A;50/60Hz
200-240VAC 3A; 50Hz
Audio Input
Input Impedance 10K ohm nominal, AC coupled
Maximum Input Voltage (L
Sensitivity 100 mV at 1 KHz for 88 dB SPL at 1 meter
Connector Type 3.5 mm (1/8 inch) stereo phone mini
+ RIN)
IN
L
or RIN < 2.0 Vrms for THD ≤ 0.3%
IN
< 4.5 V for THD ≤ 0.3%
PEAK
35
Appendix
Accessories
Standard Accessories
(ship with the projector)
Quick Start
User’s Guide
Shipping Box
VESA Computer Cable
Composite Video Cable
Computer Audio Cable 6 ft (1.8 m)
Audio Adapter (RCA to 3.5mm)
PS/2 Mouse Cable
USB Mouse Cable
Executive Plus Remote
Projection Lamp Module
Lens Cap
card
NOTE: Use only Toshiba-
approved accessories. Other
products have not been tested with
the projector.
NOTE: You can purchase these
items by contacting your dealer or
visiting Toshiba’s website at
projectors.toshiba.com.
36
Power Cords (one ships with projector, type depends on country)
North American Power Cord
Australian Power Cord
UK Power Cord
European Power Cord
Danish Power Cord
Swiss Power Cord
Optional Accessories
Deluxe Carry Case
Shipping Case (ATA approved)
Deluxe Travel Case
Macintosh Adaptor
Full-Feature Laser Pro Remote Control
GyroPoint II Radio Frequency Remote
Remote Receiver
Kensington MicroSaver Security System
S-Video Cable
Programming Cable
rd
Year Advantage Service Plan
3
(1 year extension)
NOTE: You can purchase these
items by contacting your dealer or
visiting Toshiba’s website at
projectors.toshiba.com.
37
Appendix
NOTE: Visit our website at
projectors.toshiba.com for the
most current activation chart.
Portable Computer Activation Chart
Many portable computers do not automatically turn on their
external video port when a projector is connected. Activation
commands for some portable computers are listed in the following table. (If your computer is not listed or the given command
does not work, refer to the computer’s documentation for the
appropriate command.) On many portable computers, the activa-
tion function key is labeled with an icon, for example or
the text CRT/LCD.
NOTE: Usually, pressing the key
commands once activates the
external video port, pressing it
again activates both the external
and internal ports, and pressing it
a third time activates the internal
port. Refer to your computer’s
documentation for details on your
specific model.
Key command to
Computer
Acer Ctrl-Alt-Esc (for setup) Ctrl-Alt-Esc (for setup)
AST* ** FN-D or Ctrl-D FN-D or Ctrl-D
AMS FN-F2 FN-F2
AMT setup screen setup screen
AT &T F N- F 3
Advanced Logic
Research
Altima Shift-Ctrl-Alt-C Shift-Ctrl-Alt-L
Ambra** FN-F12 FN-F12
Amrel* ** setup menu setup menu
Apple see Mac Portable and Mac PowerBook
Aspen automatic automatic
Award FN-F6 FN-F6
activate port
Ctrl-FN-D Ctrl-FN-D
FN-F5 FN-F5
type from A:/IVGA/CRT type from A:/IVGA/CRT
FN-F12 FN-F12
FN-F6
Ctrl-Alt-V Ctrl-Alt-V
setup VGA/
Conf.Simulscan
FN-F5 FN-F5
F2/Choose Option/F5 F2/Choose Option/F5
Shift-Ctrl-D Shift-Ctrl-D
Key command to
de-activate port
FN-F3
FN-F6
setup VGA/
Conf.Simulscan
38
Key command to
Computer
BCC* automatic reboot computer
Bondwell LCD or CRT options after
Chaplet** setup screen setup screen
Chembook FN-F6 FN-F6
Commax Ctrl-Alt-#6 Ctrl-Alt-#5
Compaq* ** Ctrl-Alt-< Ctrl-Alt->
Compuadd* ** automatic automatic
Data General Ctrl-Alt-Command Ctrl-Alt-Command
Data General
Wal k about
Datavue Ctrl-Shift-M Ctrl-Shift-M
DEC** FN-F5 FN-F5
Dell** Ctrl-Alt-< Ctrl-Alt->
Digital* automatic reboot
Dolch dip switch to CRT dip switch to LCD
Epson dip switch to CRT dip switch to LCD
Everex* setup screen option setup screen option
For-A Ctrl-Alt-Shift-C Ctrl-Shift-Alt-L
Fujitsu FN-F10
activate port
bootup
FN-F6 FN-F6
FN-F4 FN-F4
FN-F4 FN-F4
automatic automatic
mode/? (for setup option) mode/? (for setup option)
Alt-F for screen setup
option
2 CRT/X at DOS prompt reboot
FN-F4 FN-F4
Ctrl-Alt-F10 Ctrl-Alt-F10
FN-F8 (CRT/LCD) FN-F8
FN-D FN-D
FN-F12 FN-F12
FN-F2 FN-F2
Key command to
de-activate port
reboot for LCD or CRT
options to appear
Alt-F for screen setup
option
39
Appendix
Key command to
Computer
Gateway FN-F3
Grid* ** FN-F2, choose auto or
Hitachi FN-F7 FN-F7
Honeywell FN-F10 FN-F10
Hyundai setup screen option setup screen option
IBM 970* automatic warm reboot
IBM ThinkPad** reboot, enter setup menu FN-F2
Infotel FN-F12 FN-F12
Kaypro boot up, monitor plugged inunplug monitor
activate port
FN-F1/FN-F1 again simultaneous
simultaneous
Ctrl-Alt-Tab Ctrl-Alt-Tab
FN-F7, select choice from
setup menu
FN-F1, select choice
FN-F5, select choice
PS/2 SC select choice
(CRT, LCD, etc.)
Key command to
de-activate port
FN-F3
FN-F1
FN-F2
40
Kris Tech FN-F8 FN-F8
Leading Edge FN-T FN-T
Mac Portable
100
Mac PowerBook
140, 145, 150,
170
160, 165, 180,
520, 540, 5300
210, 230, 250,
270, 280, 2300
Magitronic FN-F4 FN-F4
Mastersport FN-F2 FN-F1
no video port: not compatible
no video port: requires a 3rd-party interface
Control Panel folder, PowerBook Display folder;
Activate Video Mirroring
requires Apple Docking Station or Mini Dock
warm reboot
Key command to
Computer
Micro Express* automatic warm reboot
Micron FN-F2 FN-F2
Microslate* automatic warm reboot
Mitsubishi SW2 On-Off-Off-Off SW2 Off-On-On-On
NCR setup screen option setup screen option
NEC* ** setup screen option setup screen option
Olivetti* automatic automatic
Packard Bell* ** FN-F0 FN-F0
Panasonic FN-F2 FN-F2
Prostar Ctrl-Alt-S at bootup Ctrl-Alt-S at bootup
Samsung* setup screen option setup screen option
Sanyo setup screen option setup screen option
Sharp dip switch to CRT dip switch to LCD
Sun SPARCDataview
Tandy** Ctrl-Alt-Insert Ctrl-Alt-Insert
Tangent FN-F5 FN-F5
Texas Instruments*
Top-Link* ** setup screen option setup screen option
Toshiba* ** Ctrl-Alt-End Ctrl-Alt-Home
Twinhead* FN-F7 FN-F7
WinBook Ctrl-Alt-F10 Ctrl-Alt-F10
activate port
CRT at the DOS prompt LCD at the DOS prompt
FN-F3 FN-F3
FN-O/* FN-O/*
Ctrl-Alt-< Ctrl-Alt->
Ctrl-Shift-M Ctrl-Shift-M
setup screen option setup screen option
setup screen option setup screen option
FN-F6 FN-F6
FN-End FN-Home
FN-F5 FN-F5
setup screen option setup screen option
FN-F5 FN-F5
Automatic Automatic
Key command to
de-activate port
41
Appendix
Key command to
Computer
Wyse software driven software driven
Zenith** FN-F10 FN-F10
Zeos** Ctrl-Shift-D
* These manufacturers have models that automatically send video
to the external CRT port when some type of display device is
attached.
** These manufacturers offer more than one key command depend-
ing on the computer model.
activate port
FN-F2 FN-F2
FN-F1 FN-F1
FN-F1
Key command to
de-activate port
Ctrl-Shift-D
FN-F1
42
Using Video Mirroring with a PowerBook Computer
When you turn video mirroring (called SimulScan in newer PowerBooks—see below) on, the projector displays the same information that appears on your PowerBook’s built-in screen. When
video mirroring is off, the projector acts like a separate display.
To turn on video mirroring for the first time:
Open the Monitors control panel; click on Monitor 2.
1
Set the number of colors you want.
2
Open the Control Strip, then click on the monitor icon.
3
Select “Turn Video Mirroring On.”
4
Now you can turn video mirroring on and off from the Control
Strip without having to open the Monitors control panel again.
When using video mirroring and high color graphics such as
slide shows, the projected image occasionally might turn black
and white. If this happens, perform the following steps:
Turn off video mirroring.
1
Open the Monitors control panel.
2
Move the white menu bar to Monitor 2 to set the projector as
3
the primary monitor.
Restart the PowerBook.
4
Using SimulScan
Some newer PowerBooks display images on an external monitor
or projector differently than previous ones. When using
SimulScan, the projector displays the same information that
appears on your PowerBook
To select SimulScan:
Open the Control Panel, then double-click Monitors and
1
Sound.
In the Resolution list, choose the SimulScan mode, then click
2
OK.
If this changes your display settings, a dialog box appears.
3
Click OK to confirm the change.
43
Appendix
NOTE: Use the graph and tables
to help you determine projected
image sizes.
Projected Image Size
F
IGURE 23
Projected image size
44
Ta b le 1:
Image Size, Width and Height for TDP-B1-maximum image size
Distance to
Screen (feet)
4.9 3.2 2.6 1.9
85.24.23.1
12 7.8 6.3 4.7
16 10.4 8.3 6.3
20 13.0 10.4 7.8
30 19.5 15.6 11.7
Image Size, Width and Height for TDP-B1-minimum image size
Distance to
Screen (feet)
4.9 2.5 2.0 1.5
84.13.32.5
12 6.2 4.9 3.7
16 8.2 6.6 4.9
20 10.3 8.2 6.2
30 15.4 12.3 9.2
Diagonal
(feet)
Ta b le 2:
Diagonal
(feet)
Width
(feet)
Width
(feet)
Height
(feet)
Height
(feet)
INDEX
A
accessories, ordering 36, 37
activation commands for laptop com-
puters 38
adjusting
brightness 19
color 20
contrast 19
tint 19
volume 17, 20
adjusting the height of the projector 15
altitude limits 35
assistance. See Technical Support
Audio menu 20
Audio menu options
Volume 20
Auto Source Select 24
B
Blank Screen 20
brightness, adjusting 19
buttons on keypad
Lamp on/off 16
Menu 16
Source 16
Standby 17
Volume 17
C
cables
audio 7
composite video 9
mouse 8
ordering 36
power 36
S-video 9, 37
cleaning the projection lens 27
color, adjusting 20
colors
don’t match monitor colors 34
not displayed 31
compatibility
IBM-compatible 1
Macintosh 1
composite video cable
connecting 9
computers, compatible 1
connecting
IBM-compatible computer 7
mouse 8
power cord 11
video player 9–10
contrast, adjusting 19
Controls menu 23
Controls menu options
Auto Source Select 24
Default Source 24
Display Messages 24
Display Startup Screen 25
Plug and Play 24
Rear Projection 24
Standby Time 23
Video Standard 23
45
Index
D
Default Source 24
Display menu 19
Display menu options
Blank Screen 20
Brightness 19
Color 20
Contrast 19
Reset All 20
Tint 19
Display Messages 24
Display Startup Screen 25
displaying
on-screen menus 16
startup screen 25
status messages 24
E
elevator button/foot 15
F
fuzzy lines 22
I
IBM-compatible computers
compatibility 1
connecting 7
image
adjusting 11, 13
centering 22
colors don’t match computer’s 34
focusing 15
fuzzy lines 22
has lines or spots 33
not centered 31
not displayed 31
out of focus 33
quality 31–34
resolution 1
reversed 24, 33
size 5, 44
streaked 33
too wide or too narrow 32
zooming 15
Image menu 21
Image menu options
Auto Image 21
Auto Resize 21
Horiz. Position 22
Manual Sync 21
Manual Tracking 22
Vert. Position 22
46
K
Kensington lock 30, 37
keypad 16
L
lamp
ordering 36
replacing 27
turns off unexpectedly 34
lamp hour counter 26
Lamp on/off button 16
Language menu 25
language, selecting for menus 25
lens
cap 36
cleaning 27
M
Macintosh computers
compatibility 1
connecting 7
Menu button 18
menus. See on-screen menus
monitor, projected colors don’t match
34
mouse, connecting 8
N
NTSC video 23
O
on-screen menus
Audio menu 20
changing language of 25
Controls menu 23
Display menu 19
displaying 18
Image menu 21
Language menu 25
making changes to menu
functions 18
Status menu 26
P
PAL video 19, 23
Plug and Play 24
portable computers
activation sequence to allow
secondary display 38
compatibility 7
connecting IBM-compatible 7
power cord
connecting 11
ordering 36
power up sequence 11, 32
project from behind the screen 24
R
rear projection 24
remote control
replacing the batteries 30
using 13, 16
replacing projection lamp module 27
re-positioning the image on the screen
22
resetting adjustments 20
resolution 1
S
safety guidelines iii
SECAM video 19, 23
security feature 30
SimulScan, using with PowerBooks 43
Source button 16
specifications 35
Standby button 17
Standby Time 23
startup screen 25
Status menu 26
S-video
connecting 9
ordering cable 37
47
Index
T
TDP-B1
project from behind the screen 24
setting up 5
specifications 35
turning off 12
turning on 11
Technical Support
information to have on hand
before you call 34
temperature limits 35
test pattern 31
text not visible 31
tint, adjusting 19
troubleshooting 31
turning off the projector 12
turning on the projector 11
U
USB mouse 8
V
vertical lines displayed 22, 33
VESA computer cable 7
video 19
video mirroring on a PowerBook 43
video standards 23
Volume buttons 17
volume, adjusting 17, 20
W
warranty 37
Z
zooming the image 15
48
LIMITED WARRANTY
Toshiba Corporation (“Toshiba”) warrants that each TDP-B1 (“the Product”) sold hereunder will conform to and function
in accordance with the written specifications of Toshiba. Said limited warranty shall apply only to the first person or entity
that purchases the Product for personal or business use and not for the purpose of distribution or resale. The product may
contain recycled components that are in new condition. Said warranty shall continue for a period of two (2) years from the
date of such purchase. The standard limited warranty excludes the lamps in projectors after 90 days and the accessories
after one year. Toshiba does not warrant that the Product will meet the specific requirements of the first person or entity
that purchases the Product for personal or business use. Toshiba’ liability for the breach of the foregoing limited warranty
is limited to the repair or replacement of the Product or refund of the purchase price of the Product, at Toshiba’ sole option.
To exercise the Purchaser’s rights under the foregoing warranty, the Product must be returned at the Purchaser’s sole cost
and expense, to Toshiba or to any authorized Toshiba service center provided, however, that the Product must be accompanied by a written letter explaining the problem and which includes (i) proof of date of purchase; (ii) the dealer’s name; and
(iii) the model and serial number of the Product. When sending your unit in for repair, please ship your unit in its original
packing material or an Toshiba approved ATA Shipping Case, or have a professional packaging company pack the unit.
Please insure your shipment for its full value. A return authorization number, issued by the Toshiba customer service
department, must also be clearly displayed on the outside of the shipping carton containing the Product.
WARRANTY LIMITATION AND EXCLUSION
Toshiba shall have no further obligation under the foregoing limited warranty if the Product has been damaged due to
abuse, misuse, neglect, accident, unusual physical or electrical stress, unauthorized modifications, tampering, alterations,
or service other than by Toshiba or its authorized agents, causes other than from ordinary use or failure to properly use the
Product in the application for which said Product is intended.
DISCLAIMER OF UNSTATED WARRANTIES
THE WARRANTY PRINTED ABOVE IS THE ONLY WARRANTY APPLICABLE TO THIS PURCHASE. ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. THERE ARE NO WARRANTIES
THAT EXTEND BEYOND THE FACE HEREOF AND THE FOREGOING WARRANTY SHALL NOT BE EXTENDED,
ALTERED OR VARIED EXCEPT BY WRITTEN INSTRUMENT SIGNED BY Toshiba.
LIMITATION OF LIABILITY
IT IS UNDERSTOOD AND AGREED THAT Toshiba’ LIABILITY WHETHER IN CONTRACT, IN TORT, UNDER ANY
WARRANTY, IN NEGLIGENCE OR OTHERWISE SHALL NOT EXCEED THE RETURN OF THE AMOUNT OF THE
PURCHASE PRICE PAID BY PURCHASER AND UNDER NO CIRCUMSTANCES SHALL Toshiba BE LIABLE FOR SPECIAL, INDIRECT OR CONSEQUENTIAL DAMAGES OR LOST PROFITS, LOST REVENUES OR LOST SAVINGS. THE
PRICE STATED FOR THE PRODUCT IS A CONSIDERATION IN LIMITING Toshiba’ LIABILITY. NO ACTION,
REGARDLESS OF FORM, ARISING OUT OF THE AGREEMENT TO PURCHASE THE PRODUCT MAY BE BROUGHT
BY PURCHASER MORE THAN ONE YEAR AFTER THE CAUSE OF ACTION HAS ACCRUED.
Part Number 010-0228-00
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment
is operated in a commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference
at his own expense.
Canada
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
Safety Certifications
UL, CUL, TÜV, NOM
EN 55022 Warning
This is a Class A product. In a domestic environment it may cause radio interference, in which case the user may be required to take adequate measures. The typical use is in a conference room, meeting room or auditorium.
Declaration of Conformity
Manufacturer: Toshiba
1-1, Shibaura 1-Chome, Minato-ku, Tokyo, Japan
We declare under our sole responsibility that the TDP-B1 Projector conforms to
the following directives and norms:
Directive 89/336/EEC, Amended by 93/68/EEC
EMI: EN 55022 (1992) Class A
EMC: EN 50082-1 (1992)
IEC 801-2, IEC 801-3, IEC 801-4
Directive 73/23/EEC, Amended by 93/68/EEC
Safety: EN 60950: 1992 + A1 + A2 + A3: 1995
July, 1999
Trademarks
Apple, Macintosh, and PowerBook are trademarks or registered trademarks of
Apple Computer, Inc. IBM and PS/2 are trademarks or registered trademarks of
International Business Machines, Inc. MicroSaver and Kensington are trademarks
or registered trademarks of Kensington Microware Limited. Microsoft, PowerPoint, and Windows are trademarks or registered trademarks of Microsoft Corporation. Digital Light Processing is a trademark or registered trademark of Texas
Instruments.
Loading...