Toshiba TCB-PCDM2E APPLICATION CONTROL MANUAL

SW07

Power peak-cut control board

(1) Be sure to turn off the power switch before installing.

(2) Place this P.C. board by using the support on the upper side of the electric component

box. There are four installation holes to place the support on the upper side of the electric

component box.

(3) Install the P.C.board to the supports.

Be careful the terminal block direction

as the interior side.

(4) Connect the P.C.board (TCB-PCDM2E)PJ17

and outdoor unit interface CN513

withconnection cable.

(5) Bind the remaining connection cable with the

attached banding band.

Wiring

SN：EH99839001

INSTALLATION MANUAL

MODEL:

TCB-PCDM2E

Feature

The upper limit capacity of the outdoor unit is restricted based on the demand request signal from outside

Dimension

No.

1 2 3 4 5 6

Q’ty

1 4 2 1 1 2

Parts name Connection cable Support to fix the board Earth screw Wire-clamp Screw for wire-clamp Banding band

Terminal(Screw M3)

Terminal(Screw M4)

4-φ4 hole

Accesory parts

Placing position

Power peak-cut control board

Outdoor unit interface PC board

[ Outdoor unit ] [ Electric component box ]

CN513(Blue

)

How to install

Terminal block

Correct direction

Incorrect direction

Safety Precautions

WARNING

CAUTION

This symbol is used to identify action which, if carried out in an incorrect ignoring this indication, could lead to serious personal injury or even death.

Installation of accessory parts should be performed either by personnel from this dealer where it was purchased or by specialist installation technicians.

Reassembling, repair, or modification of this accessory parts is strictry forbidden.

Do not install a location where flammable gasses may be present.

Repair of the accessory parts must also carried out by personnel from dealer where it was purcased.

Use the specified wires for wiring connect the terminals securely fix. To prevent external forces applied to the terminals from affecting the terminals.

This symbol is used to identify action which, if carried out in an incorrect ignoring this indication, could lead to serious human injury or property damage.

l Please read this section carefully before installation work to install the accessory parts in the

prescribed manner. The precaution given here deal with serious safety issues. It is, therefore, of the utmost importance that they are observed in full.

The meanings of safety-related symbol are as follows:

After installation work has been completed, perform a trial operation of the equipment in order to ensure that it is operating normally, and then hand over to the customer and ask to keep this Safety Precautions and Installation Instruction.

Incorrect installation by unqualified personnel can result in electric shock, fire or abnormal operation.

Fire may break out should flammable gas leak into the vicinity of the parts.

Failure to follow these directions can result in inflammation, earth leakage or abnormal operation

causing electric shock or injury.

WARNING

Size(mm):H20 x L85 x W71 Weight(g): 65

Length

Shield wire

TypeSize

In conformity with design 60245 IEC 57

Input wiring

Output wiring

Up to 500m

Up to 200m

Up to 400m

2-core or 3-core, 0.75mm

2-core, 0.75mm2

2-core, 1.5mm2

(1) Refer to the "Electric wiring diagram" when wiring. (2) Be sure to use the shield wire to prevent noise trouble, and perform the grounding at both

sides of shield wires.

(3) Fix the output wiring with the wire clamp and banding band.

(3)-1.

Let the output wiring into the banding band and band it together with the other wiring.

(3)-2. Fix the wire-clamp using the screw hole on the "B" position.

[ Electric component box ]

Banding band

Wire-clamp

Output wiring

(Local supply)

Function / Electric wiring diagram

Two type control can be selected by setting SW07(Bit2)on the interface P.C. board of the header unit.

[ Standard function ]

I/F P.C. Board

Place this option P.C. Board to header unit.

Connection

Cable

Local Supply

: Display lamp suring power peak-cut control.

TCB-PCDM2E SW07-Bit2 OFF

Power Supply

OPERATION

COM

OFF

PJ17CN513

SW1

SW2

Display Relay

SW07

Bit2 OFF

Input

SW1 OFF



SW2



OFF

Bit1 OFF



100%(Normal)

0%(Stop)

Bit1 ON



100%(Normal)

Up to 60%

SW07-Bit1 Display Relay

(L1)

CAUTION) 

・Be sure to prepare a non-voltage point for each terminal.

 ・Display Relay capacity of "OPERATION"

Below AC240V 0.5A (COSφ=100%) When connecting load such as relay coil to "L1" load, insert the noise surge absorber. Below DC24V 1A (Non-inductive load)

When connecting load such as relay coil to "L1" load, insert the the bypass circuit.

 ・Supplementary Insulation must be added to user touchable part of switches.

In case of pulse signal Be sure to prepare the point of contact for each terminal. The time of the pulse signal is more than 100msec. Don’t switch on both SW1 and SW2 terminal simultaneously.

PJ17

I/F P.C. Board

Place this option P.C. Board to header unit.

Local Supply

: Display lamp suring power peak-cut control.

TCB-PCDM2E

SW07-Bit2 ON

Power Supply

OPERATION

COM

OFF

CN513

SW1

SW2

Display Relay

SW07

Bit2 ON

Input

SW1 OFF



OFF

SW2



OFF OFF

ON ON

OFF

ON ON ON

Bit1 OFF



100%(Normal)

Up to 80% Up to 60%

0%(Stop)

Bit1 ON



100%(Normal)

Up to 85% Up to 75% Up to 60%

SW07-Bit1 Display Relay

(L1)

CAUTION)  ・Be sure to prepare non voltage continuous point of contact for each terminal.  ・Display Relay capacity of "OPERATION"

Below AC240V 0.5A (COSφ=100%) When connecting load such as relay coil to "L1" load, insert the noise surge absorber. Below DC24V 1A (Non-inductive load) When connecting load such as relay coil to "L1" load, insert the bypass circuit.  ・Supplementary Insulation must be added to user touchable part of switches.

Connection

Cable

[ Expansion function ]

Install this P.C. board to the upper side of the electric component box on outdoor unit.

CCoonnnneeccttoorr aanndd SSwwiittcchh ppoossiittiioonn oonn iinntteerrffaaccee PPCC bbooaarrdd