ENGLISH
WIRELESS CONTROLLER
OPERATION MANUAL
For general public use
RB-RXS30-E
1112150109
EN
EN
EN
EN
EN
EN
EN
1
e
s
n
h
k
c
o q
i
b
g
f
d
a
m
j
rp
l
1 PREPARATION BEFORE USE
Preparing Filters
1. Open the air inlet grille and
remove the air fi lters.
2. Attach the attachment fi lters
(see detail in the accessory
sheet).
Loading Batteries
1. Remove the battery cover.
2. Insert 2 new alkaline batteries
(AAA type) following the (+)
and (–) positions.
Removing the batteries
1. Remove the cover, and take out the batteries.
2. Reattach the cover.
• Please dispose of the batteries according
to the local regulation.
Clock Setup
1. Push
by tip of the pencil.
If timer indication is fl ashing, go to
the next step 2.
2. Press
or : adjust the
time.
3. Press
: Set the time.
Remote Control Reset
1. Remove the batteries.
2. Press
.
3. Insert the batteries.
Remote Control Caring
1. Clean the remote control with a wet cloth when needed.
2. No benzine, thinner, polishing powder or chemicallytreated duster.
2 REMOTE CONTROL
1 Infrared signal emitter
2 Start/Stop button
3 Mode select button (MODE)
4 Temperature button (TEMP)
5 Fan speed button (FAN)
6 Swing louver button (SWING)
7 Set louver button (FIX)
8 Weekly timer setting button
9 Memory and Preset button
(PRESET)
! 8°C heating operation
button (8°C)
" High power button
(Hi-POWER)
# Economy button (ECO)
$ Comfort sleep button
(COMFORT SLEEP)
% Floor warming
mode button (FLOOR)*
& Clock Reset button (CLOCK)
( Check button (CHECK)
) Reset button (RESET)
~ Filter reset button (FILTER)
+ Power selection button (POWER-SEL)
3
AUTOMATIC / COOLING (DRY) /
HEATING / FAN ONLY OPERATION
1. Press : Select Auto A, Cool , Dry , Heat , or
Fan only
.
2. Press
: Set the desired temperature.
Min. 17°C, Max. 30°C.
3. Press
: Select AUTO, LOW , LOW+ , MED ,
MED+
, HIGH , and Quiet ( ).
※AUTOMATIC OPERATION : Choose cooling or heating
operation automatically.
※In DRY OPERATION mode, it can not select air volume.
※ In FAN ONLY OPERATION mode, it does not show setting
temperature.
Insert direction of
(+) and (-) correctly
Pull the cover
away fi rmly.
4 Hi-POWER OPERATION
To automatically control room temperature and airfl ow for faster
Auto, cooling or heating operation (except in DRY mode).
Press
: Start and stop the operation.
6 ECO OPERATION
To automatically control room to save energy (except in DRY
mode).
Press
: Start and stop the operation.
Note: Cooling operation; the internal set temperature will
increase automatically 1 degree by 2 hours (maximum
2 degrees increase). For heating operation the internal
set temperature will decrease.
7 TIMER OPERATION
Set the timer when the air conditioner is operating.
Setting the ON Timer Setting the OFF Timer
1
Press
: Set the
desired
ON timer.
Press : Set the
desired
OFF timer.
2
Press
: Set the
timer.
Press : Set the
timer.
3
Press
: Cancel the
timer.
Press : Cancel the
timer.
Setting the ON-OFF Timer
1
Press
: Set the
ON timer.
3
Press
.
2
Press
: Set the
OFF timer.
4
Press
: Cancel
the timer.
Note:
• Keep the remote control in accessible transmission to the
indoor unit; otherwise, the time lag of up to 15 minutes will
occur.
• The setting will be saved for the next same operation.
5 FLOOR WARMING OPERATION
Heating will operate with downward blowing only.
Temperature of air outlet will be higher than usual.
* Floor can work only if indoor unit is Bi-fl ow console.
2
9 8°C OPERATION
1. Press button to change to 8°C set temperature
heating operation.
2. Press
to adjust setting temperature from 5°C to
13°C.
Note: 8°C will operate in Heating mode only. If Air conditioner
performs in cooling operation (including automatic
cooling) or dry operation it will change to heating
operating.
10 COMFORT SLEEP OPERATION
For comfortable sleep, automatically control air fl ow and
automatically turn OFF (Except in DRY mode and Fan only
mode).
1. Press
: Select 1, 3, 5 or 9 hrs for OFF timer
operation.
2. Press
to cancel the comfort sleep operation.
Note: The cooling operation, the set temperature will increase
automatically 1 degree/hour for 2 hours (maximum
2 degrees increase). For heating operation, the set
temperature will decrease.
8 PRESET OPERATION
Set your preferred operation for future use. The setting will
be memorized by the unit for future operation (except airfl ow
direction).
1. Select your preferred operation.
2. Press and hold
until stop blinking and the P
mark displays.
3. Press
: Operate the preset operation.
11 FILTER RESET
Firstly, turn off the circuit breaker.
FILTER lamp lights on; the fi lter must be cleaned.
To turn off the lamp, press RESET button on the indoor unit for
Hi-wall or ON/OFF button for Bi-fl ow console, also can push the
FILTER button on the remote control in another way. (Please
follow the instructions in the air conditioner owner’s manual.)
12
REMOTE CONTROL A-B
SELECTION
To separate using of remote control for each indoor unit in case
of 2 air conditioners are installed nearly.
Remote Control B Setup.
1. Press RESET button on the indoor unit to turn the air
conditioner ON for Hi-wall type or press and hold MODE
button on the indoor unit more than 20 seconds for Bi-fl ow
console type. (Please follow the instructions in the air
conditioner owner’s manual.)
2. Point the remote control at the air conditioner.
3. Push and hold
button on the Remote Control by the
tip of the pencil. “00” will be shown on the display.
4. Press
during pushing . “B” will show on the
display and “00” will disappear and the air conditioner will
turn OFF. The Remote Control B is memorized.
Note: 1. Repeat above step to
reset Remote Control
to be A.
2. Remote Control A has
not “A” display.
3. Default setting of Remote
Control from factory is A.
13
POWER-SELECTION OPERATION
This function is used when its circuit breaker is shared with
other electrical appliances. It limits the maximum current/power
consumption to 100%, 75% or 50%. The lower the percentage,
the higher the saving and also the longer the compressor
lifetime.
Press
: Select: (for 100%), (for 75%),
(for 50%)
• When the level is selected, PWR-SEL level fl ashes on
LCD display for 3 seconds. In case of 75% and 50% level,
number “75” or “50” also fl ashes for 2 seconds.
• Due to the reason that POWER SELECT FUNCTION limits
the maximum current, inadequate capacity may occur.
EN
EN
EN
EN
EN
EN
EN
3
14 WEEKLY TIMER OPERATION
4 programs for each day in the week can be set in WEEKLY TIMER.
The following items can be set in WEEKLY TIMER operation.
a. Operation time (ON timer for Start and OFF timer for Stop operation)
b. Operation mode
c. Temperature setting.
d. Fan speed setting.
e. Special operation (8°C, ECO, Hi-POWER)
Examples of WEEKLY TIMER uses
1. Living room
ON+HI-POWER
24 C
OFF
OFF
ON+ECO
23 C
MON-FRI
SUN and SAT
ON
24 C22 C
OFF
ON
OFF
ON
2. Living room with heavy cool (Non-stop air conditioning)
MON-FRI
ON+ECO
ON+HI-POWER
23 C 10 C
17 C
24 C
ON+ECO
ON+8ºC
ON
24 C
10 C
23 C
17 C
ON+ECO
ON
ON
SUN and SAT
ON+8ºC
3. Bedroom
23 C 24 C 24 C
OFF
ON
ON+Hi-POWER
ON
ON+ECO
ON
Sunday Sunday Monday Monday
4
How to set WEEKLY TIMER
TEMP.
PRESET
1. Press to enter WEEKLY TIMER setting.
Blink
2. Press to select desired day in sequence.
The sequence of day symbol appears on the LCD
SU MO TU WE TH FR SA
WEEKLY SUMO
TUWETHFRSA
(All day)
3. Press to select the program number.
• The program 1 is ready for setting while
is
pressed PG-1 appears on the LCD.
• Press
to change the program number in the
sequence program 1 to program 4.
PG-1
PG- 2
PG- 3
PG- 4
4. Press or to select the desired time.
• The time can be set between 0:00 and 23:50 in 10
minute intervals.
• Press and hold the button to change setting time for 1 hr.
• Only one of ON or OFF timer can be set on each
program.
ON timer display OFF timer display*
* OFF timer is used to stop the air conditioner only. The
display does not show Operation mode, Temperature,
Fan speed and others.
5. Press
to select desired operation.
6. Press or
TEMP.
to select desired temperature.
• The temperature can be set between 17°C and 30°C.
7. Press
to select the desired fan speed.
8. Add operations, if required.
• Press
to use 8°C operation.
• Press
to use ECO operation
• Press
to use Hi-POWER operation.
9. Adding or editing the program.
The program can be set to perform on all the required days
until
is pressed to confi rm the setting 10.
If adding or editing a program is required, please repeat
steps 2 - 8 before setting confi rmation.
10. After adding or editing, press to confi rm the setting*.
Weekly timer
running
Next program
Timer ON
or OFF
Next operation
time
Operating Temperature
and Fan speed
Display after
pressing SET
button
Operating Mode
* Point remote control at air conditioner receiving module
then, press SET button until you hear the “PiPi” sound.
This means the setting operation has been completed.
As the air conditioner is receiving the signal, you will hear
separate “Pi” sounds corresponding to the number of days
in the selected setting.
An incomplete setting is indicated if the TIMER lamp is
blinking. Press
twice.
EN
EN
EN
EN
EN
EN
EN
5
To delete programs
TEMP.
PRESET
The individual program
1. Press
.
• The day of the week and the program number is
displayed.
• Select the day to delete the program.
2. Press
to select the program number to be deleted.
3. Press
.
• ON or OFF timer will be cleared and the LCD will blink.
4. Press
to delete the program.
• Press
while the LCD is blinking. The program has
now been deleted.
All programs
1. Press
.
• The day of the week and the program number will be
displayed.
2. Press
and hold for 3 seconds.
• All programs will be deleted and LCD displays current
operation.
Note: Make sure the remote control receiving module on the air
conditioner receives the signal from the remote control.
Note:
1. Place the remote control where the indoor unit can receive
the signal. This will increase the accuracy of the timing
between the remote control and the air conditioning unit.
2. The ON/OFF timer can be set during the WEEKLY TIMER
operation. In this situation, the air conditioner will fi rst
follow the normal timer until it is complete; then, it will
return to the WEEKLY TIMER function.
3. During WEEKLY TIMER operation, all of operation such
as MODE, TEMP, FAN, Hi-POWER, ECO and etc., can be
adjusted but when the clock reaches the program setting,
the operation will return to the set items in the program.
4. When the remote control is sending a signal to the air
conditioner, avoid interference from objects that can block
the signal.
Edit WEEKLY TIMER program
TEMP.
PRESET
To edit the program after confi rming the weekly timer setting on
Page 4
, follow steps 1 - 3 below.
1. Press
.
• The day of the week and the program number of the
current day will be displayed.
2. Press
to select the day of the week and press
to select program number to be confi rmed.
• Resetting the operation.
3. Press
to exit confi rming mode.
Deactivating WEEKLY TIMER operation
Press
while “WEEKLY” is displayed on the LCD.
• The “WEEKLY” indicator will disappear from the LCD.
However, the program will remain in the remote control.
• The TIMER lamp goes off.
• To reactivate the WEEKLY TIMER operation again, press
again, LCD shows the next program. The program,
after reactivation, is related to the clock time.
1112150109
Information according to EMC Directive 2004/108/EC
(Name of the manufacturer) TOSHIBA CARRIER (THAILAND) CO., LTD.
(Address, city, country) 144/9 MOO 5, BANGKADI INDUSTRIAL PARK,
TIVANON ROAD, TAMBOL BANGKADI, AMPHUR
MUANG, PATHUMTHANI 12000, THAILAND.
(Name of the Importer / Distributor in EU) TOSHIBA CARRIER UK LTD.
(Address, city, country) Porsham Close, Belliver Industrial Estate, PLYMOUTH,
Devon, PL6 7DB. United Kingdom
Loading...