Toshiba RAS-13SKVR-E2, RAS-10SAV, RAS-10SKV, RAS-13SKVR Owners Manual
OWNER’S MANUAL
025052.indb
2/5/09 2:2:20 PM
ENGLISH
ESPAÑOL
FRANÇAIS
ITALIANO
DEUTSCH
PORTUGUÊS
POLSKI
ÿESKY
PУCСКИЙ
HRVATSKI
MAGYAR
TÜRKÇE
NEDERLANDS
AIR CONDITIONER (SPLIT TYPE)
For general public use
Indoor unit
RAS-10SKV Series
RAS-13SKVR Series
Outdoor unit
RAS-10SAV Series
RAS-13SAVR Series
025052.indb
ΕΛΛΗΝΙΚΑ
SVENSKA
SUOMI
NORSK
DANSK
ROMÂNĄ
БЪЛГАРСКИ
EESTI
LATVISKI
SLOVENÿINA
SLOVENŠÿINA
025052
2/5/09 2:2:20 PM
PRECAUTIONS FOR SAFETY
025052.indb 2
2/5/09 2:2:23 PM
• Do not install, repair, open or remove the cover. It may expose you to
dangerous voltages. Ask the dealer or the specialist to do this.
• Turning off the power supply will not prevent potential electric shock.
DANGER
WARNING
CAUTION
1
INDOOR UNIT DISPLAY
Models: RAS-3SKVR Series
Hi POWER FILTER PURE TIMER OPERATION
12
Models: RAS-0SKV Series
RESET TIMER OPERATION
32 1
2
PREPARATION BEFORE USE
Preparing Filters
. Open the air inlet grille and remove the air fi lters.
2. Attach the fi lters. (see detail in the accessory sheet).
Loading Batteries
. Remove the battery cover.
2. Insert 2 new batteries (AAA type)
following the (+) and (–) positions.
Clock Setup
. Push CLOCK
2. Press
3. Press
Remote Control Reset
. Remove the battery.
2. Press
3. Insert the battery.
3
AIRFLOW DIRECTION
1
2
3
Note:
• Do not move the louver manually by others.
• The louver may automation positioning by come operation mode.
• The appliance shall be installed in accordance with national wiring
regulation.
• Means for disconnection from the supply having a contact separation
of at least 3 mm in all poles must be incorporated in the fi xed wiring.
• Do not expose your body directly to cool air for a long time.
• Do not insert your fi nger or any article into the air inlet/outlet.
• When an abnormality (burning smell, etc.) occurs, stop the air
conditioner and disconnect the power supply or turn off the breaker.
• This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities, or
lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a
person responsible for their safety.
• Children should be supervised to ensure that they do not play with
the appliance.
• Do not wash the unit with water. It may cause an electric shock.
• Do not use this air conditioner for other purposes such as preserving
food, breeding animal, etc.
• Do not step or put anything on the indoor/outdoor unit. It may cause
an injury or damage the unit.
• Do not touch aluminium fi n because it may cause an injury.
• Before cleaning the unit, turn off the main switch or the circuit
breaker.
• When the unit won’t be used for a long time, turn off the main switch
or the circuit breaker.
• It is recommended that maintenance be performed by a specialist
when the unit has been operated for a long time.
1 Hi POWER (Green)
2 FILTER (Orange)
3 PURE (Blue)
4 TIMER (Yellow)
5 OPERATION (Green)
6 RESET button
RESET
6
1 OPERATION (Green)
2 TIMER/CLEANING (Yellow)
3 RESET button
CLEANING
45
3
O
by tip of the pencil.
ON
OFF
or
SET
: Set the time.
: adjust the time.
.
FIX
Press
desired vertical direction.
Press
automatically and press again to stop.
For horizontal direction, adjust
manually.
: Move the louver in the
SWING
: Swing the air
A
C
L
4
REMOTE CONTROL
PRESET
ONE-TOUCH
QUIET
SWING
TIMER
SLEEP
1
TEMP
PURE
FIX Hi-POWER ECO
ON
FILTER
CHK
FAN
MODE
COMFORT
SLEEP
CLR
OFF
SET
CLOCK
1 Infrared signal emitter
2 Start/Stop button
3 Mode select button (MODE)
4 Temperature button (TEMP)
5 Fan speed button (FAN)
6 Swing louver button (SWING)
7 Set louver button (FIX)
8 On timer button (ON)
9 Off timer button (OFF)
! Sleep timer button (SLEEP)
" Setup button (SET)
# Clear button (CLR)
$ Memory and Preset button (PRESET)
% One Touch button (ONE-TOUCH)
& High power button (Hi-POWER)
( Economy button (ECO)
) Quiet button (QUIET)
~ Comfort sleep button (COMFORT SLEEP)
+ Plasma Air Purifi er button (PURE)
(RAS-3SKVR Series Only)
, Filter reset button (FILTER)
- Clock Reset button (CLOCK)
. Check button (CHK)
5
ONE-TOUCH
Press the “ONE-TOUCH” button for fully automated operation that is customised
to the typical consumer preferences in your region of the world. The customised
settings control temperature air fl ow strength, air fl ow direction and other settings
to provide you alternate contact with “ONE-TOUCH” of the button. If you prefer
other settings you can select from the many other operating functions of your
Toshiba unit.
ONE-TOUCH
Press
6
AUTOMATIC OPERATION
To automatically select cooling, heating, or fan only operation
. Press
2. Press
7
COOLING / HEATING / FAN ONLY OPERATION
. Press
2. Press
Cooling: Min. 7
3. Press
HIGH .
8
DRY OPERATION (COOLING ONLY)
For dehumidifi cation, a moderate cooling performance is controlled
automatically.
. Press
2. Press
9
AIR PURIFYING OPERATION
During air conditioner operation
Press
The plasma air purifi er and air ionizer can be activated or deactivated during air
conditioner is stopped and the air ionizer starts in conjunction with plasma air
purifi er operation.
Note: The FILTER indicator (orange) turns on after PURE operation is performed
10
Hi-POWER OPERATION
To automatically control room temperature and airfl ow for faster cooling or heating
operation (except in DRY and FAN ONLY mode)
Press
11
ECO OPERATION
To automatically control room to save energy (except in DRY and FAN ONLY
mode)
Press
Note: Cooling operation; the set temperature will increase automatically degree/
: Start the operation.
MODE
: Select A.
TEMP
: Set the desired temperature.
MODE
: Select Cool , Heat , or Fan only .
TEMP
: Set the desired temperature.
o
C, Heating: Max. 30oC, Fan Only: No temperature indication
FAN
: Select AUTO, LOW , LOW+ , MED , MED+ , or
MODE
: Select Dry .
TEMP
: Set the desired temperature.
PURE
to start and stop plasma air purifi er and air ionizer operation.
for about 000 hours.
Hi-POWER
: Start and stop the operation.
ECO
: Start and stop the operation.
hour for 2 hours (maximum 2 degrees increase). For heating operation the
set temperature will decrease.
$
%
2
)
+
6
7
8
!
.
,
(RAS-13SKVR Series Only)
5
4
3
~
&
(
#
9
"
-
025052.indb 2
2/5/09 2:2:23 PM
12
025052.indb 3
2/5/09 2:2:27 PM
TEMPORARY OPERATION
In case of the misplaced or discharged remote control
• Pressing the RESET button, the unit can start or stop
without using the remote control.
• Operation mode is set on AUTOMATIC
operation, preset temperature is 24°C
and fan operation is automatic speed.
13
TIMER OPERATION
Setting the ON Timer Setting the OFF Timer
1
PressON : Set the desired ON timer.
2
3
Daily timer allows the user to set both the ON & OFF timers and will be activated on a daily basis.
Setting Daily Timer
1
2
• During the daily timer is activating, both arrows ( , ) are indicated.
Note:
• Keep the remote control in accessible transmission to the indoor unit;
• The setting will be saved for the next same operation.
14
Set your preferred operation for future use. The setting will be memorized by the
unit for future operation (except airfl ow direction).
. Select your preferred operation.
2. Press and hold
3. Press
15
To automatically restart the conditioner after the power failure (Power of the unit
must be on.)
Setting
. Press and hold the RESET button on the indoor unit for 3 seconds to set the
• Do not operate ON timer and OFF timer.
2. Press and hold the RESET button on the indoor unit for 3 seconds to cancel the
16
To operate at super low fan speed for quiet operation (except in DRY mode)
Press
Note: Under certain conditions, QUIET operation may not provide adequate
17
To save energy while sleeping, automatically control air fl ow and automatically
turn OFF.
Press
Note: The cooling operation, the set temperature will increase automatically
18
To start the sleep timer (OFF timer) operation
Press
19
SET
Press
: Set the timer. Press
CLR
Press
: Cancel the timer. Press
PressON: Set the ON timer.
OFF
Press
: Set the OFF timer.
otherwise, the time lag of up to 5 minutes will occur.
PRESET OPERATION
PRESET
displays.
PRESET
for 3 seconds to memorize the setting. The P mark
: Operate the preset operation.
AUTO RESTART OPERATION
operation. (3 beep sound and OPERATION lamp blink 5 time/sec for 5 seconds)
operation. (3 beep sound but OPERATION lamp does not blink)
QUIET OPERATION
QUIET
: Start and stop the operation.
cooling or heating due to low sound features.
COMFORT SLEEP OPERATION
COMFORT
SLEEP
: Select , 3, 5 or 9 hrs for OFF timer operation.
degree/hour for 2 hours (maximum 2 degrees increase). For heating
operation, the set temperature will decrease.
SLEEP TIMER OPERATION
SLEEP
: Select , 3, 5 or 9 hrs for OFF timer operation.
MAINTENANCE
Press
3
Press
Press
4
mark fl ashing.
OFF
: Set the desired OFF timer.
SET
: Set the timer.
CLR
: Cancel the timer.
SET
.
SET
button during the ( or )
Firstly, turn off the circuit breaker.
Filter Reset (Some models only)
FILTER lamp lights on; the fi lter must be cleaned.
To turn off the lamp, push the RESET button on the indoor unit or the FILTER
button on the remote control.
Indoor Unit and Remote Control
• Clean the indoor unit and the remote control with a wet cloth when needed.
• No benzine, thinner, polishing powder or chemically-treated duster.
Cleaning the air ionizer (Once every six months) (RAS-13SKVR Series Only)
. Turn off air conditioner using remote control and power supply.
2. Fully open the vertical air fl ow louvers by hand.
3. Use a toothbrush to rub the ends of metal pin three or four times.
Note: Do not use cotton swabs or other objects with fl uff.
Cleaning the plasma air purifi er unit (About 1000 hours performed)
(RAS-13SKVR
. Turn off air conditioner using remote control and power supply.
2. Take out the air inlet grille (See detail in installation manual).
3. Take out the plasma air purifi er by grasp the handle, and the pull it out.
4. Soak in hot water at 40
down, left, right and rub surface gently with a sponge.
5. Allow to dry thoroughly in the shade.
6.
Attach the plasma air purifi er by grasp the handle
and insert into the right and left guide rails.
7. Press both ends of the plasma air purifi er
until the protrusions on both sides of the
plasma air purifi er are completely inserted.
Attach the air fi lter, and then close the air inlet grille.
8.
20
SELF CLEANING OPERATION (COOL AND DRY OPERATION ONLY)
To protect bad smell caused by the humidity in the indoor unit.
. If the
to run for other 20 minutes, then it will turn off automatically. This will reduce the
moisture in the indoor unit.
2. To stop the unit immediately, press the
Note:
• SELF CLEANING operation is default setting from factory.
To cancel this function, press and hold the reset button on the indoor unit for 20 seconds.
•
The SELF CLEANING operation will be cancelled. (5 beep sound but OPERATION
lamp does not blink)
• Do the same to set this function again. (5 beep sound and OPERATION lamp
blink 5 time/sec for 5 seconds)
• AUTO RESTART operation will be cancelled by setting or cancellation of SELF
CLEANING operation. Set it again if necessary.
21
OPERATION AND PERFORMANCE
. Three-minute protection feature: To prevent the unit from being activated for 3
minutes when suddenly restarted or switched to ON.
Preheating operation: Warm up the unit for 5 minutes before the heating operation starts.
2.
3. Warm air control: When the room temperature reaches the set temperature,
the fan speed is automatically reduced and the outdoor unit will stop.
4. Automatic defrosting: Fans will stop during defrost operation.
5. Heating capacity: Heat is absorbed from outdoors and released into the room.
When the outdoor temperature is too low, use another recommended heating
apparatus in combination with the air conditioner.
Consideration for accumulated snow: Select the position for outdoor unit where it will
6.
not be subjected to snow drifts, accumulation of leaves or other seasonal debris.
7.
Some minor cracking sound may occur when unit operating. This is normal
because the cracking sound may be caused by expansion/contraction of plastic.
Note: Item 2 to 6 for Heating model
Air conditioner operating conditions
Operation
Heating –5°C ~ 24°C –0°C ~ 24°C Less than 28°C
Cooling –0°C ~ 46°C 5°C ~ 43°C 2°C ~ 32°C
Dry –0°C ~ 46°C 5°C ~ 43°C 7°C ~ 32°C
22
TROUBLESHOOTING (CHECK POINT)
The unit does not operate.
• The power main switch is turned off.
• The circuit breaker is activated to
cut off the power supply.
• Stoppage of electric current
• ON timer is set.
23
REMOTE CONTROL A-B SELECTION
To separate using of remote control for each indoor unit in case of 2 air conditioner
are installed nearly.
Remote Control B Setup.
. Press RESET button on the indoor unit to turn the air conditioner ON.
2. Point the remote control at the indoor unit.
3. Push and hold
be shown on the display.
4. Press
will disappear and the air conditioner will turn OFF. The Remote Control B is
memorized.
Note:
2. Remote Control A has not “A” display.
3. Default setting of Remote Control from factory is A.
Series
Only)
o
C to 50oC for about 0 to 5 minutes and rub up,
button is pressed once during “Cool” or “Dry” mode, the fan will continue
3 times within 30 seconds.
Temp.
Outdoor Temperature
RAS-13SKVR Series RAS-10SKV Series
Temperature
Cooling or Heating is abnormally low.
• The fi lters are blocked with dust.
•
The temperature has been set improperly.
• The windows or doors are opened.
• The air inlet or outlet of the outdoor
unit is blocked.
• The fan speed is too low.
• The operation mode is FAN or DRY.
CHK O
button on the Remote Control by the tip of the pencil. “00” will
MODE
during pushing
CHK O
. “B” will show on the display and “00”
. Repeat above step to reset Remote Control to be A.
EN
Room
025052.indb 3
2/5/09 2:2:27 PM
Loading...