Toshiba IK-VR01A User Manual

Page 1
INSTRUCTION MANUAL
CCD COLOR CAMERA
IK-VR01A
Please read this manual thoroughly before use, and keep it handy for future reference.
Record in space provided below the Model No. and the Serial No. as found on the label on the bottom of this unit. Model. No. IK-VR01A Serial No. Retain this information for future reference.
TABLE OF CONTENTS
Important safeguards
1. Features & Description ................................................. 3
3. Components ................................................................. 3
4. Part Names & Functions............................................... 4
5. Connections and Operations ........................................ 5
6. Installations................................................................... 7
7. Line Lock Phase ........................................................... 12
8. Note on use and Installation ......................................... 12
9. In Case of Problems ..................................................... 13
10. Specifications................................................................ 14
11. Exterior View................................................................. 15
Page 2
IMPORTANT SAFEGUARDS
1. Read Instructions
All the safety and operating instructions should be read before the product is operated.
2. Retain Instructions
The safety instructions and instruction manual should be retained for future reference.
3. Heed Warnings
All warnings on the product and in the instruction manual should be adhered to.
4. Follow Instructions
All operating and use instructions should be followed.
5. Cleaning
Disconnect this video product from the power supply before cleaning.
6. Attachments
Do not use attachments not recommended by the video product manufacturer as they may cause hazards.
7. Water and Moisture
Do not use this video product near water-for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool and the like.
8. Accessories
Do not place this video product on an unstable cart, stand, tripod, bracket or table. The video product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with stand, tripod, bracket, or table recommended by the manufacturer, or sold with the video product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.
9. Ventilation
This video product should never be placed near or over a radiator or heat register. This video product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.
10.Power Sources
This video product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your location, consult your product dealer.
11.Power-Cord Protection
Power-Supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, screws and the point where they exit from the product.
12.Installation
This video product should be installed on a firm and solid part of the ceiling or wall. If installed on a soft and weak place, the camera unit may fall. A person under it may be injured and things under it may be damaged.
13.Lightning
For added protection for this video product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the power supply and cable system. This will prevent damage to the video product due to lightning and power-line surges. However, if there is thunder or lightning now, do not touch the unit and any connected cable. This will for you not to receive the electric shock by the serge of thunder.
14.Overloading
Do not overload power supply and extension cords as this can result in a risk of fire or electric shock.
15.Object and Liquid Entry
Never push objects of any kind into this video product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electrical shock. Never spill liquid of kind on the video product.
16.Servicing
Do not attempt to service this video product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
17.Damage Requiring service
Disconnect this video product from the power supply and refer servicing to qualified service personnel under the following conditions. a. When the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the video product. c. If the video product has been exposed to rain or water. d. If the video product does not operate normally by following the operating instructions in the instruction manual. Adjust only those controls that are covered by the instruction manual as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the video product to its normal operation. e. If the video product has been dropped or the cabinet has been damaged. f. When the video product exhibits a distinct change in performance-this indicates a need for service.
18.Replacement Parts
When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer with the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock or other hazards.
19.Safety Check
Upon completion of any service or repairs to this video product, ask the service technician to perform safety checks to determine that the video product is in proper operating condition.
- 1 -
Page 3
The CAUTION label, shown on the left,
is attached on the camera.
CAUTION TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightening flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage within the products enclosure
WARNING :
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE. that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
CAUTION :
CONNECT 24V AC UL LISTED CLASS 2
POWER SUPPLY.
FIELD INSTALLATION :
WORDED : THIS INST ALLA TION SHOULD
BE MADE BY A QUALIFIED SERVICE
PERSON AND SHOULD CONFORM TO
ALL LOCAL CODES.
FCC NOTICE
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
USER-INSTALLER CAUTION : Your authority to operate this FCC verified equipment could be voided if you make changes or modifications not expressly approved by the party.
Serial No Label The serial No. label is located here.
- 2 -
Page 4
1. FEATURES & DESCRIPTION
IK-VR01A has the following features: (1) Flush/Surface mount. (2) IP66 Standard for dust and water resistance. (3) Built in vari-focal lens with auto-iris
Focal length 3.0~8.0mm.
(4) Incorporated 1/3" type CCD image sensor gives high resolution and excellent
sensitivity 480 lines horizontal resolution
0.4 lx minimum illumination with tint dome cover (5) 50dB Signal-To Noise Ratio (6) Power supply- AC24V or DC12V - This camera automatically detects the power. (7) BLC, AGC, and Line-Lock (AC24V)
2. CAUTIONS
(1) Avoid touching the lens glass with your fingers. If necessary, use a soft cloth
moistened with alcohol to wipe off any dust. (2) Avoid aiming the camera at the sun. (3) Avoid shooting the camera at intense light. Intense light such as a spotlight may
cause a bloom or smear. A vertical stripe may appear on the screen.
However, this is not a malfunction. (4) Install the camera away from video noise. If cables are wired near electric lighting
wires or a TV set, noise may appear in images. In this event, relocate cables or
reinstall equipment.
3. COMPONENTS
(1) Camera (with Tint Dome Cover installed) 1 pc. (2) Accessories
(a) Mounting Base 1 pc.
(b) Bracket 1 pc.
(c) Screw A 3 pcs.
(d) Screw B 3 pcs.
(e) Clear Dome Cover 1 pc.
(f) Special Hexangular Wrench 1 pc.
(g) Monitor Out Harness Wire 1 pc.
(h) Power Connector 1 pc.
(i) Instruction Manual 1 pc.
- 3 -
Page 5
4. PART NAMES & FUNCTIONS
Mode Setting Switch
LL
ON
OFF
BLC (Backlight Compensation Switch
BLC
With the switch on, it adjusts the backlight automatically to obtain the best possible image. LL Sets camera synchronization to line lock with the switch on. Available only with AC24V.
Lens Iris ADJ
Counterclockwise: The picture becomes
)
darker. Clockwise: The picture becomes brighter. "Optimum Value" is at default setting.
Line Lock Phase ADJ
Adjusts the phase of the line lock.
Monitor Out Connector
Connect with the supplied monitor out harness wire. Used to adjust the angle of view when installing the camera.
- 4 -
Page 6
5. CONNECTIONS AND OPERATIONS
Notes on connecting
Power plugs to connected equipment must be disconnected before installation.
A 75-ohm coaxial cable (3C-2V or 5C-2V) is required for standard connection.
For details of wiring and operation of equipment to be connected, refer to their
operation manuals.
Coaxial cables for video signals and the power cord are not supplied with the camera.
Refer to the operations manuals of connected equipment for detailed wiring and overall operation instructions.
5-1 Basic connection single system configuration
Video Monitor
BNC Connector
Supplied Power Connector
( ) POWER CORD (twisted pair line) minimum wire size of 18 AWG is recommended.
24V AC UL Listed Class 2 power supply / 12V DC power supply
CAUTION : Never input 24V AC and 12V DC at the same time.
In case of DC12V , connect “+12” to red cable and “GND” to black cable.
12V DC
AC 120V
Do not overload power supply
Since this camera uses 24V AC UL Listed Class 2 power supply or 12V DC power supply, it should be connected to a power supply that allows for at least 5w consumption. Because the IK-VR01A uses a mechanism, a sufficient power supply with adequate current specifications is required.
- 5 -
Page 7
5-2 Line-Lock Control
Matching the vertical synchronization with the power frequency is called the Line­Lock.
This function is activated when the LL of Mode Setting Switch is on.
When two or more cameras are switched by the video switcher for viewing by a monitor
TV, the vertical sync. phase can be locked with the power frequency, and a stable vertical sync. is obtained without being disturbed at the time of switching.
Video Monitor
VIDEO SWITCHER
CAMERA1
TO AC 24V UL Listed class 2 power supply
When connecting to DC power supply, the Line-Lock function is not activated.
CAMERA2
Note :
The camera is synchronized to the power frequency of 60±1Hz covering a normal fluctuation of the power frequency. However, the camera may not cover a large fluctuation caused from the power generated by an engine generator, etc.
It takes about 10 seconds or more until a stable synchronization is obtained after the power is turned on. This is normal, because several seconds are required to stabilize the camera against power noise.
Refer to 7. LINE-LOCK PHASE for adjustment.
- 6 -
Page 8
6. INSTALLATIONS
Connect the cable of the camera and the cable from the designated power supply with respective connectors.
Screws for fixing the camera and mounting base to the ceiling or wall are not supplied with the unit. Use appropriate screws.
Note :
The weight (camera body only) is about 1.3kg. The camera unit including the mounting base and the bracket weighs 2.1kg.
When installing to surfaces of other materials, use the screws to fix it firmly.
6-1 Adjust the Angle of View
Security screws
Top Cover
a
Camera Base
(1) Loosen the three security screws by the supplied special hexangular wrench and
remove the top cover.
Important Notice :
a
Be sure to remove three silver screws cover. The screws are used to temporarily fix the top cover for transportation.
immediately after removing the top
- 7 -
Page 9
Tilt rotation
a
Horizontal rotation
1
Pan Lock
2
Tilt Lock
4
Focus lock lever
FAR
NEAR
3
WIDE
Zoom lock lever
TELE
1
a
a
Pan
a
Transport Protection Screws (silver)
Remove three silver screws transport protection.
(2) The lens direction in pan direction can be adjusted by turning pan lock
counterclockwise to unfasten it without moving the lens. After adjustment, turn pan lock 1 clockwise to fasten it.
Note :
Do not turn the lens over 360°. Otherwise the inner connector may be broken and the image may not appear.
(3) The lens tilt angle can be adjusted by loosening the tilt lock 2. After adjusting,
tighten the tilt lock 2.
(4) Adjust the zoom position by loosening the zoom lock lever 3. After adjusting,
tighten the zoom lock lever 3.
(5) Adjust the focus by loosening the focus lock lever 4. After adjusting, tighten the
focus lock lever 4.
(6) Repeat the adjustments from step (1) to step (5) till the optimum image appears.
- 8 -
Page 10
6-2 Installing the Camera Unit
6-2-1
Installation to Wall or Ceiling with Mounting Base (Surface Mount Installation)
When installing the camera unit on the wall, mount it with the drain groove on the downside. Do not block the drain groove.
When installing the camera unit outdoor, make waterproof for the cables. The camera body is water-resistant but the brackets are not water-resistant.
Mounting Base center
Mounting Base
Drain groove
Screws (not supplied) x4
Fix firmly.
Drain groove
A
Cable exit (sideway)
Rear cable hole
85 mm
Cable access hole ø27 mm
Mounting Base center
46 mm
B
85 mm
7
55 mm
With female screw for piping
Cable access hole ø27 mm
In case of using the variable mounting holes
46 mm
C
55 mm
83.5 mm
, Wall or Ceiling
C
A
, Junction Box
D
B
D
83.5 mm
7
Screws x3
Mount camera base with three supplied screws A. (Longer screw(M4x16)) Tighten and lock the screws firmly.
Top Cover
Camera Base
Align to this mark.
- 9 -
Mount the top cover (the assembly of the dome cover) and secure it firmly with three security screws by the supplied special hexangular wrench.
Align to this mark.
Page 11
6-2-2 Installation to Junction Box with Bracket (Flush Mount Installation)
Screws (not supplied) x4
Screws x3
46 mm
Bracket
Junction Box
83.5 mm
Note the direction of the bracket, which has two sides.
Align the marks.
Mount camera base with three supplied screws B. (Shorter screw(M4x10)) Tighten and lock the screws firmly.
- 10 -
Mount the top cover (the assembly of the top dome cover) and secure it firmly with three security screws by the supplied special hexangular wrench.
Align to this mark.
Page 12
6-2-3 Change of Dome Cover
Screws (x3)
Retainer plate Put the protruding side downward.
The protruding portion should be set in the groove of the shock damper.
Shock damper cushion Note the direction of the damper
cushion. The groove should be face up.
Dome cover
Gasket
Top cover
Dome replacement
When the dome cover is damaged or to be replaced by a transparent cover, call your distributor or sales person. Firmly tighten three mounting screws. Take care not to let dirt or foreign object enter between the parts.
- 11 -
Page 13
7. LINE LOCK PHASE
When a video switcher switches two or more cameras, the picture may fluctuate on the video monitor due to the different AC line phase of each camera. In this case, adjust the V PHASE controller to get a stable image.
Line Lock V PHASE CONTROL
8. NOTE ON USE AND INSTALLATION
• Do not aim the camera at the sun
Do not aim the camera at the sun or point it at sun even if you are not shooting.
• Do not shoot intense light
Intense light such as a spotlight may cause a bloom or smear. A vertical stripe may appear on the screen. However, this is not a malfunction.
• Treat the camera with care
Do not drop the camera or subject it to strong shock of vibration. Otherwise, the camera may malfunction.
• Never touch internal parts
Do not touch the internal parts of the camera other than the parts specified. Otherwise, the camera may malfunction.
• Do not splash water on the camera
Install the camera where the camera can be kept dry . If the camera gets wet, turn off the power and contact your dealer.
• Check the ambient temperature and humidity
Avoid using the camera where the temperature is hotter or colder than specified. Otherwise, the quality of images may deteriorate or internal parts may be affected. Special care is required to use the camera at high temperature and humidity.
• Should you notice any trouble
If any trouble occurs while you are using the camera, turn off the power and contact your dealer. If you continue to use the camera when there is something wrong with it, the trouble may much worse and an unpredictable accident may occur.
- 12 -
Page 14
9. IN CASE OF PROBLEMS
Condition
No image
Unnatural color
The image is out of focus.
The image is dark.
Check Points
Are the camera and connected equipment turned on?
Are cables connected correctly?
Is the monitor TV adjusted correctly?
Is the lighting too weak?
Is the lens focus adjusted?
Is the lens or cover dirty?
Are there any large barrier or bright illumination near the
camera?
Is the lens iris adjustment volume correctly set?
- 13 -
Page 15
10.SPECIFICATIONS
1. Image System
Image Device Pixel Elements
2. Electrical
TV System
Horizontal Resolution S/N Ratio Minimum Illumination
Auto Gain Control (AGC) Iris Control Mode White Balance White Balance Range Line lock Vertical phase adjustment Gamma compensation Backlight Compensation (BLC) Video Output Signal Synchronization System
3. Mechanical
Weight
Dimension
4. Optical
Built-in Lens
View Angle
Focus Length
5. Power
Input Voltage Power Consumption
6. Environmental
Operating Temperature Storage Temperature Water proof:IP66
7. Regulation
Safety Dust and Water Resistance Emission
Design and specifications are subject to change without notice.
1/3 IT CCD 771 (H) x 492 (V)
2:1 Interlace, 15.734KHz Horizontal, 59.94Hz Vertical
480 TV lines 50dB (TYP. White 100%, Weight On, SC TRAP ON)
0.2 lux (More than 10% of image output, Clear dome cover)
0.4 lux (More than 10% of image output, Tint dome cover) Average AGC (24dB) Auto Iris Lens Auto 2500°K ~ 10000°K Provided (VR : range 300deg)
0.45 On / Off (DIP-SW) VBS (1.0Vp-p, 75ohm unbalance, BNC) Internal for DC or Linelock for AC
Camera : 1.3kg, Mounting Base : 0.6kg, Bracket : 0.2kg
Camera : 170mm (D) x 150mm (H) with Mounting Base : 175mm (D) x 155mm (H)
Vari-focus Lens f=3.0 ~ 8.0mm, F1.0 (Wide) /F1.45 (Tele) : Auto Iris
Wide : 117.3° (D), 90.8° (H), 66.6° (V) Tele : 45.2° (D), 36.2° (H), 27.0° (V)
0.2m ~
DC12V or AC24V
3.0W
-10°C~50°C 90%RH max
-20°C~60°C 70%RH max
UL2044 IP66 FCC Class A / DOC ClassA
- 14 -
Page 16
11.EXTERIOR VIEW
)
45.5
SR
(
unit : mm
)175
( φ
()155
- 15 -
()48.5
()110
Page 17
(SR
45.5
unit : mm
)
()150
)170
( φ
()61.5
()147.5
- 16 -
()41
Page 18
Bracket
120
46
unit : mm
110
4-M4
120
83.5
Mounting Base
85
46
4.4
85
83.5
5
4- φ6.5
4- φ4.5
6- φ5.5
4- φ6.5
60
20
40 1515
7
φ
27
114
82
4-M6 Depth=10
40 1515
55
- 17 -
Page 19
- 18 -
Loading...