Toshiba D-VRW1 Owner's Manual
Hi-Fi VCR & DVD VIDEO RECORDER
D-VRW1SU
OWNER’S MANUAL
2
23
33
48
52
61
Introduction
Various settings
Disc playback
Tape playback
Recording
Editing the disc
DIGITAL VIDEO
©2005 Toshiba Corporation
76
79
Dubbing
Additional information
This device does not tape-record copy protected DVD Video Discs.
W1
2G00101A Cover 3/7/05, 5:13 PM1
Introduction
2
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, do not expose this appliance to rain
or moisture.
CAUTION: TO PREVENT ELECTRIC SHOCK DO NOT USE THIS POLARIZED PLUG WITH AN
EXTENSION CORD, RECEPTACLE OR OTHER OUTLET UNLESS THE BLADES CAN
BE FULLY INSERTED TO PREVENT BLADE EXPOSURE.
FCC NOTICE:This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
-
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Changes or modifications not expressly approved by the partly responsible for compliance with the
FCC Rules could void the user's authority to operate this equipment.
CAUTION: THIS DIGITAL VIDEO PLAYER EMPLOYS A LASER SYSTEM.
TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS USER'S GUIDE CAREFULLY AND RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE MAINTENANCE, CONTACT AN AUTHORIZED SERVICE LOCATION.
USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHER
THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
TO PREVENT DIRECT EXPOSURE TO LASER BEAM, DO NOT TRY TO OPEN THE ENCLOSURE. VISIBLE LASER RADIATION MAY BE PRESENT WHEN THE ENCLOSURE IS OPENED.
DO NOT STARE INTO BEAM.
The lightning flash with arrowhead symbol, within an
equilateral triangle is intended to alert the user to the
presence of uninsulated dangerous voltage within the
product's enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the appliance.
Location of the required Marking
The rating sheet and the safety caution are on the rear of the unit.
CERTIFICATION: COMPLIES WITH FDA RADIATION PERFORMANCE
STANDARDS, 21 CFR SUBCHAPTER J.
SAFETY PRECAUTIONS
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER
(OR BACK). NO USER-SERVICEABLE
PAR TS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
2G00101A P02-P07 3/8/05, 7:07 PM2
Introduction
3
1. READ INSTRUCTIONS
All the safety and operating instructions should be read before the unit is operated.
2. RETAIN INSTRUCTIONS
The safety and operating instructions should be retained for future reference.
3. HEED WARNINGS
All warnings on the unit and in the operating instructions should be adhered to.
4. FOLLOW INSTRUCTIONS
All operating and use instructions should be followed.
5. CLEANING
Unplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a soft dry cloth for cleaning the exterior cabinet only.
6. ATTACHMENTS
The manufacturer of this unit does not make any recommendations for attachments, as they may cause
hazards.
7. WATER AND MOISTURE
Do not use this unit near water. For example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet
basement, or near a swimming pool.
8. ACCESSORIES
Do not place this unit on an unstable cart, stand, tripod, bracket, or table.
The unit may fall, causing serious injury, and serious damage to the unit.
8A. An appliance and cart combination should be moved with care. Quick stops,
excessive force, and uneven surfaces may cause the appliance and cart
combination to overturn.
9. VENTILATION
Slots and openings in the cabinet back or bottom are provided for ventilation,
to ensure reliable operation of the unit, and to protect it from overheating.
These openings must not be blocked or covered. The openings should never be blocked by placing the unit
on a bed, sofa, rug, or other similar surface. This unit should never be placed near or over a radiator or heat
source. This unit should not be placed in a built-in installation such as a bookcase or rack unless proper
ventilation is provided and/or the manufacturer’s instructions have been adhered to.
10. POWER SOURCE
This unit should be operated only from the type of power source indicated on the rating plate. If you are not
sure of the type of power supply to your home, consult your appliance dealer or local power company.
11. GROUNDING OR POLARIZATION
This unit is equipped with a polarized alternating-current line plug (a plug having one blade wider than the
other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert
the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to
replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.
12. POWER-CORD PROTECTION
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point
where they exit from the appliance.
S3125A
PORTABLE CART WARNING
(symbol provided by RETAC)
IMPORTANT SAFEGUARDS
2G00101A P02-P07 3/7/05, 5:13 PM3
Introduction
4
IMPORTANT SAFEGUARDS
13. LIGHTNING
To protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time,
unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the
unit due to lightning and power line surges.
14. POWER LINES
An outside antenna system should not be located in the vicinity of overhead power lines or other electric
light or power circuits, or where it can fall onto or against such power lines or circuits. When installing an
outside antenna system, extreme care should be taken to keep from touching such power lines or circuits,
as contact with them might be fatal.
15. OVERLOADING
Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.
16. OBJECT AND LIQUID ENTRY
Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short
out parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.
17. OUTDOOR ANTENNA GROUNDING
If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is
grounded to provide some protection against voltage surges and built-up static charges, Section 810 of the
National Electrical Code, ANSI/NFPA 70, provides information with respect to proper grounding of the mast
and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding
conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for
the grounding electrode.
EXAMPLE OF ANTENNA GROUNDING AS PER THE
NATIONAL ELECTRICAL CODE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ANTENNA LEAD IN WIRE
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
GROUND CLAMP
ELECTRIC SERVICE
EQUIPMENT
NEC-NATIONAL ELECTRICAL CODE
S2898A
18. SERVICING
Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified service personnel.
For example:
a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the unit.
c. If the unit has been exposed to rain or water.
d.
If the unit does not operate normally by following the operating instructions. Adjust only those controls that
are covered by the operating instructions, as an improper adjustment of other controls may result in damage
and will often require extensive work by a qualified technician to restore the unit to its normal operation.
e. If the unit has been dropped or the cabinet has been damaged.
f . When the unit exhibits a distinct change in performance, this indicates a need for service.
2G00101A P02-P07 3/7/05, 5:13 PM4
Introduction
5
CONDENSATION
Moisture will form in the operating section of the DVD/VCR if the unit is brought from cool surroundings into a warm
room or if the temperature of the room rises suddenly. When this happens, the DVD/VCR’s performance will be
impaired.
To prevent this, let the DVD/VCR stand in its new surroundings for about an hour before switching it on, or make
sure that the room temperature rises gradually.
Condensation may also form during the summer if the DVD/VCR is exposed to the breeze from an air conditioner.
In such cases, change the location of the DVD/VCR.
* This product incorporates copyright protection technology that is protected by method claims of certain U.S.
patents and other intellectual property rights owned by Macrovision Corporation and other rights owners.
Use of this copyright protection technology must be authorized by Macrovision Corporation and is intended
for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation.
Reverse engineering or disassembly is prohibited.
Consumers should note that not all high definition television sets are fully compatible with this product and
may cause artifacts to be displayed in the picture. In case of 525 progressive scan picture problems, it is
recommended that the user switch the connection to the “STANDARD DEFINITION” output. If there are
questions regarding our TV set compatibility with this model 525p DVD player, please contact our customer
service center.
* Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of
Dolby Laboratories.
* “DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.
* Unauthorized recording of copyrighted television programs, films, video cassettes and other materials may
infringe the rights of copyright owners and be contrary to copyright laws.
* Certain audio features of this product manufactured under a license from Desper Products, Inc. Spatializer
®
,
N-2-2™ and the circle-in-square device are trademarks owned by Desper Products, Inc.
* Windows Media and the Windows logo are either registered trademarks or trademarks of Microsoft
Corporation in the United States and/or other countries.
19. REPLACEMENT PARTS
When replacement parts are required, be sure the service technician uses replacement parts specified by
the manufacturer or those that have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock or other hazards.
20. SAFETY CHECK
Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to
determine that the unit is in proper operating condition.
21. HEAT
The product should be situated away from heat sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.
22. DISC TRAY
Keep your fingers well clear of the disc tray as it is closing. It may cause serious personal injury.
23. CONNECTING
When you connect the product to other equipment, turn off the power and unplug all of the equipment from
the wall outlet. Failure to do so may cause a product damage. Read the owner's manual of the other equipment carefully and follow the instructions when making any connections.
24. LASER BEAM
Do not look into the opening of the disc tray or ventilation opening of the product to see the source of the
laser beam. It may cause sight damage.
25. DISC
Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious
personal injury and product malfunction.
26. NOTE TO CABLE TV SYSTEM INSTALLER
This reminder is provided to call the Cable TV system installer’s attention to Article 820-40 of the NEC that
provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.
IMPORTANT SAFEGUARDS
2G00101A P02-P07 3/7/05, 5:13 PM5
Introduction
6
Introduction
•
SAFETY PRECAUTIONS .................................... 2
•
IMPORTANT SAFEGUARDS .............................. 3
•
Contents ............................................................. 6
•
Features ..............................................................8
•
Disc ..................................................................... 9
Handling discs ................................................... 9
Discs which can be played back ........................ 9
Discs on which video can be recorded ............ 10
DVD-RW .......................................................... 10
DVD-R .............................................................. 10
Recording format ............................................. 10
Disc playback in other players ......................... 11
On Video CDs ..................................................11
•
Parts and functions ......................................... 12
Front ................................................................ 12
Rear .................................................................12
Display window ................................................ 13
Remote control ................................................ 14
Power Source .................................................. 15
•
Antenna connections ...................................... 16
•
Cable TV connections ...................................... 18
•
Connections with the TV or audio
component ........................................................ 20
•
Auto clock setting ............................................ 22
•
Setting the video channel ............................... 22
Various settings
•
SETUP MENU ................................................... 23
Using the SETUP MENU .................................23
•
Setting the language........................................ 24
OSD LANGUAGE ............................................24
DVD MENU ...................................................... 24
AUDIO .............................................................. 24
SUBTITLE........................................................ 24
•
Setting the parental control ............................ 25
Selecting parental control ................................ 25
Temporarily cancelling parental control ........... 25
•
Setting the clock .............................................. 26
CLOCK (manually) ........................................... 26
AUTO CLOCK ..................................................26
STANDARD TIME (Time zone) ........................ 26
DAYLIGHT SAVING TIME ............................... 26
•
Setting the disc ................................................ 27
REFORMAT ..................................................... 27
NEW DISC FORMAT ....................................... 27
FINALIZE .........................................................27
PROTECT DISC .............................................. 28
UNDO FINALIZE ............................................. 28
•
Other (SYSTEM SETUP) .................................. 28
DIMMER (Brightness of the display window) ... 28
DISPLAY/CALL (Turning the screen display
“ON” or “OFF”) ................................................. 28
Contents
•
Setting the screen ............................................ 29
TV SCREEN .................................................... 29
STILL MODE ................................................... 29
LINE1 INPUT/LINE2 INPUT ............................ 29
•
Setting the image quality ................................ 30
BRIGHTNESS ................................................. 30
E.B.L. ...............................................................30
•
Setting the audio .............................................. 30
DRC .................................................................30
VIRTUAL SURROUND (Spatializer N-2-2TM) ...30
EXTERNAL AUDIO INPUT ..............................30
SAP (Second Audio Program) ......................... 31
•
Setting the recording ....................................... 31
INITIAL REC TO .............................................. 31
INITIAL REC MODE ........................................ 31
AUTO CHAPTER ............................................. 31
INDEX PICTURE .............................................31
BLACK LEVEL (REC) ...................................... 31
•
Setting the channel .......................................... 32
TV/CABLE SELECT ........................................ 32
AUTO CH MEMORY ........................................32
ADD/DELETE (channels) ................................ 32
•
Setting other items .......................................... 32
JPEG INTERVAL ............................................. 32
Disc playback
•
Playback procedure .........................................33
•
Playback by selecting a title ........................... 34
•
Checking media information ........................... 35
•
Special playback .............................................. 36
Fast forward playback ...................................... 36
Review playback .............................................. 36
Still playback .................................................... 36
Frame advance ................................................ 36
Slow motion playback ...................................... 36
Locating a chapter or track .............................. 36
•
Instant skip .......................................................37
•
Locating a specific scene ............................... 37
•
Repeat playback ............................................... 38
Instant replay ................................................... 38
A-B repeat playback ........................................ 38
Title, Chapter repeat playback .........................38
•
Title selection ................................................... 39
•
DVD menu .........................................................39
•
Changing angles ..............................................40
•
Zooming ............................................................ 40
•
Karaoke playback ............................................ 40
•
Changing soundtrack language ..................... 41
•
Subtitles ............................................................ 41
Changing soundtrack language ....................... 41
Turning the subtitles On and Off ......................41
•
To turn off the PBC (VIDEO CD Version 2.0) .....
41
•
Various operations on CD ............................... 42
•
MP3/WMA/JPEG playback ............................... 44
•
Progressive scan ............................................. 47
2G00101A P02-P07 3/8/05, 7:07 PM6
Introduction
7
Media mark
Each applicable media are indicated using the symbol shown below.
•
Changing a disc name ..................................... 73
Changing a disc name .....................................73
Using the keyboard screen ..............................74
Dubbing
•
Dubbing a tape onto a disc .............................76
•
Dubbing a disc onto a tape .............................77
•
Dubbing using other equipment..................... 78
Additional information
•
Glossary ........................................................... 79
•
Language code list .......................................... 81
•
Problems and troubleshooting ....................... 82
•
Video head cleaning ........................................83
•
Error/Warning message list ............................ 84
•
Specifications................................................... 85
Tape playback
•
Loading and unloading a cassette tape ........ 48
•
Cassette tape playback ................................... 49
•
Special playback ..............................................50
Picture search .................................................. 50
Still picture ....................................................... 50
Slow motion ..................................................... 50
Frame by frame picture ....................................50
Adjusting tracking condition .............................50
Repeat playback ..............................................50
Instant skip....................................................... 50
To display VCR operation status ...................... 50
•
ZERO RETURN function .................................. 51
•
Video index search system .............................51
Recording
•
Read this before recording on disc................ 52
Types of disc .................................................... 52
Recording modes............................................. 52
Disc remaining time ......................................... 52
Images that cannot be recorded ......................53
•
Recording a TV program ................................. 54
•
One-touch Timer Recording (OTR) .................56
•
Timer recording ................................................57
•
Stereo recording and playback....................... 60
Editing the disc
•
Editing the disc ................................................ 61
•
Editing a playlist .............................................. 62
Creating a playlist ............................................ 62
Changing a title name ...................................... 63
Erasing a scene (Edit title) ............................... 64
Combining the title ...........................................66
Erasing a playlist.............................................. 67
•
Editing an original title .................................... 68
Adding a chapter mark .................................... 68
Combining chapters ......................................... 69
Changing an original title name ....................... 70
Erasing a scene (Edit title) ............................... 71
Erasing an original title .................................... 72
Contents
: DVD-Video : DVD-R
: DVD-RW in VR mode
: Audio/Video CD and CD-R/CD-RW
: DVD-RW in Video mode : Video tape
2G00101A P02-P07 3/7/05, 5:13 PM7
Introduction
8
Features
Playback function
Title menu
Video CD/SVCD/MP3/WMA/JPEG playback
Video CD/SVCD/MP3/WMA files can be played back.
Also, you can display JPEG files on the TV screen and
enjoy them as a slide show.
Progressive scan
This unit supports the progressive scanning system. If
your TV is equipped with component video input jacks
which support the progressive video input, you can
enjoy high quality picture.
Thumbnail image will not appear after finalizing DVDRW (recorded in the Video mode) and DVD-R.
•
Not only can you playback and record video tapes, but
you can also playback DVD discs or make recordings
using DVD-RW or DVD-R discs with this unit. In addition,
you can enjoy editing the programs you record.
A realistic, powerful, Movie Theater sound
When connected to Dolby Digital and DTS compliant
devices, you can enjoy realistic, powerful surround
sound.
Playback the scene you want to see immediately
As DVD’s do not require rewinding like video tapes, you
can get to the scene you wish to watch immediately. A
variety of search functions allow you to find the scene
you wish to watch.
As thumbnail images are displayed in the title menu,
you can find the title you want to play back quickly.
Recording function
Timer recording
The timer recording system allows you to select the
date, time and channel and record the desired programs. Up to 12 timer programs within a month can be
stored in this unit.
One-touch Timer Recording (OTR)
The One-touch Timer Recording feature provides a
simple and convenient way to make a timed recording.
Edit function
Editing recorded material without changing
the original titles
You can create a playlist based on the original titles.
The playlist won’t affect the original titles. If you erase
the playlist, the original titles remain. It is recommended
to create and edit the playlist to prevent important titles
from being erased accidentally.
Chapter mark
You can add (or delete) a chapter mark to (from) the
original title. This function is useful when searching for
the scene you wish to watch that you have marked with
the Chapter mark function.
Erasing scenes
You can erase an unnecessary scene from the created
playlist or the original titles.
Combining titles
You can combine several original titles or playlists to a
separate playlist.
Dubbing function
Dubbing a tape onto a disc or a disc onto a
tape
•
Dubbing cannot be carried out when attempting to
copy a “copy guarded” video tape or disc.
With just this one unit, you can dub whatever you like,
from video tape to disc, or from disc to video tape.
2G00101A P08-P11 3/7/05, 5:13 PM8
Introduction
9
Disc
Handling discs
Removing the Disc from its case
Be sure to hold the disc by its edges.
Do not touch the surface of the disc.
Ta ke the disc carefully from its case.
• Do not scratch the disc.
• Do not get dirt on the surface of the disc.
• Do not stick labels or adhesive tapes on the disc.
• Do not drop or bend the disc.
Storing discs
• Store the disc in the case to avoid any risk of
scratches, dirt or damage.
• Do not leave the disc exposed to direct sunlight or in
hot or humid places.
Cleaning discs
Wipe the disc with a clean, dry cloth from the center
outward toward the edges.
• Do not wipe the disc in a circular motion around the
center.
• Do not use liquid or aerosol cleaners.
Region management information
This unit is designed and manufactured to support the
region management information that is recorded on a
DVD disc. If the region number written on the DVD disc
does not correspond to the region number of this unit,
this unit cannot play that disc.
• The region number of this unit is “1”.
• The unit will play DVD-Video discs marked with labels containing “1” or “ALL”.
Example:
1
Operating DVD-Video
• Some operations of DVD-Video may be prohibited
by the manufacturer, or some operation methods or
functions of the DVD-Video may be different from the
description in this manual.
• If you attempt an operation that is prohibited by either the disc or the unit, a “
” mark will appear on the
TV monitor. For operations prohibited by the disc, see
the information that came with the disc.
• When the menu screen or the operation guide appears during disc playback, follow the displayed information.
Discs which cannot be played back
The discs listed below cannot be played back in general. Even if one of these can be played back, it may
not be played back correctly. If a disc is played back by
mistake, extensively loud sounds may blow the speak
ers or may damage the hearing of those in hearing
range. Do not playback the discs listed below.
CDG, Photo-CD, CD-ROM, CD-TEXT, CD-EXTRA,
SACD, PD, CDV, DVD-ROM, DVD-RAM, DVD+R/
RW, DVD audio, etc.
Notes on DVDs and Video CDs
Because of problems and errors that can occur during
the creation of DVD and Video CD software and/or the
manufacture of DVD and Video CD discs, Toshiba
cannot guarantee that this DVD/VCR will play every feature
of every DVD bearing the DVD logo and/or every Video
CD bearing the CD logo. As one of the creators of DVD
technology, Toshiba DVD players are manufactured
using the highest standards of quality, and as a result,
such incompatibilities are rare. If you happen to
experience any difficulty playing a DVD or a Video CD on
this DVD/VCR, please feel free to call our Consumer
Solution Center (see page 87).
The below DVD-Video may not be played back.
•DVD-Video that do not have the region number “1” or
“ALL”.
•PAL or SECAM DVD-Video.
• Prohibited or business-use DVD-Video.
CD-R/CD-RWs cannot be played back for the following reasons.
• Compatibility of the disc and this unit.
• Compatibility of the disc and the recorder used.
• Unfinalized discs.
Do not playback the following discs. Playback of
these discs may cause a failure.
• Discs on which paper, labels or stickers are affixed.
• Discs that have sticky areas left by adhesive tape.
• Special-shaped discs.
* This unit is designed to playback music Compact Discs (CD) that
conform to the CD standard. CDs that contain (copy-restriction) signals to protect copyrights cannot be played back.
Media type
Logo mark
l
DIGITAL VIDEO
Discs which can be played back
In this unit, use only discs that meet the standard, such
as those bearing the below logo marks on the disc label
surface. If you use a non-standard disc, we cannot guarantee playback. Even if such a disc can be played back,
we cannot guarantee the image or sound quality.
The DVD logo is a registered trademark.
DVD-R Ver.2.0(Ver.2.0/4x/8x)
Audio CD*
Video CD
SVCD
CD-R/CD-RW
DVD-Video
DVD-RW
Ver.1.0 Ver.1.1 Ver.1.2
Ver.1.1 CPRM support
2G00101A P08-P11 3/7/05, 5:14 PM9
Introduction
10
Disc
Recording format
This unit has two modes for formatting discs for recording: VR mode and Video mode.
When a blank, new disc is loaded into this unit, the automatic format function starts to format the disc. (For
the disc format setting in this step, see page 27.)
VR mode
• This mode can be used for DVD-RW.
• In this mode, the discs can be recorded and edited
repeatedly.
• The disc recorded in this mode can be played back
with other DVD-RW-compatible players.
• When a Ver.1.1 CPRM or Ver. 1.2 disc is used, you
can record a “Copy Once” program (see page 53).
Video mode
• This mode can be used for DVD-R and DVD-RW
(Ver.1.1/1.2).
• When you finalize the disc after recording, the disc
recorded with this unit can be played back with other
DVD players.
• Recording, editing or playback of an unfinalized disc
can be done only with this unit. However, there are
some limitation to editing operations.
• In this mode, you cannot record a “Copy Once” program (see page 53).
• When you record a TV program of a bilingual broadcast, only one of the audio modes can be recorded.
You have to select it.
Format modes that can be used with each disc
The usable format depends on the media type as shown
in the below table.
Media type Logo mark
DVD-RW Ver.1.0 Ver.1.1 Ver.1.2
Ver.1.1CPRM support
DVD-R Ver.2.0 (Ver.2.0/4x/8x)
DVD-RW
• The disc can be erased and used again about 1,000
times.
• Only the VR mode can be used for Ver.1.0 discs.
• With Ver.1.1/1.2 discs, you can record by selecting
the VR mode or Video mode.
• When you record in the VR mode, you can repeatedly record and erase. By erasing unnecessary titles,
you effectively increase remaining time.
• When you record in the Video mode, you can record
until the disc becomes full.
• When you use the Video mode, you can newly record
on the disc by formatting the disc. However, if the
disc is formatted, all the recorded contents will be
erased.
DVD-R
•You can record on the disc only in the Video mode.
•You can record until the disc becomes full.
• Finalizing the discs allows playback on other DVD
players. However, the finalized discs can no longer
be recorded.
• Discs can be recorded to repeatedly until they are
finalized.
NOTES:
• There are some players that cannot playback discs
that were recorded with this unit. We cannot guarantee the playback with other units.
• This unit cannot record on DVD-RW/R discs that are
8 cm in diameter.
• This unit cannot record on CD-RW/R.
Discs on which video can be recorded
To record video with this unit, use the discs below:
Media type
Format
DVD-RW
(Ver.1.0)
DVD-RW
(Ver.1.1 and
1.2)
DVD -R
(Ver.2.0/4x/8x)
Available functions
VR mode
VR mode
Video mode
Video mode
Playback, recording and
editing (Original/playlist)
Playback, recording and
editing (Original/playlist)
Playback and recording
Editing (with limitation)
Playback and recording
Editing (with limitation)
2G00101A P08-P11 3/7/05, 5:14 PM10
Introduction
11
Disc
CHAPTER 1
TITLE1 TITLE2
DVD DISC
CHAPTER 2 CHAPTER 2 CHAPTER 3CHAPTER 1
TRACK 1 TRACK 2 TRACK 3 TRACK 4 TRACK 5
Audio-CD
When recording in the Video mode
When a disc recorded in the Video mode is finalized, it
cannot be recorded onto any more. Therefore, before
finalization, be sure to perform all desired recording.
After finalization, a title list that can be used by the DVD
player is automatically created.
NOTES:
• The finalization process may require from a few minutes up to 1 hour depending on the disc type and the
amount of free space on the disc.
•A DVD-RW Ver.1.1/1.2 recorded in the Video mode
cannot be recorded or edited after finalization, but if
you format the disc by erasing all the content, you
can again record on this disc.
•A finalized disc may not play because of the condition of the DVD or the compatibility with the player
used for playback.
• Some players may not playback the discs recorded
with this unit. We cannot guarantee the playback using other players.
On Video CDs
This DVD supports Video CDs equipped with the
PBC (Version 2.0) function. (PBC is the abbreviation
of Playback Control.) You can enjoy two playback
variations depending on types of discs.
• Video CD not equipped with PBC function
(Version 1.1)
Sound and movie can be played on this DVD in the
same way as an audio CD.
• Video CD equipped with PBC function
(Version 2.0)
In addition to operation of a Video CD not equipped
with the PBC function, you can enjoy playback of
interactive software with search function by using
the menu displayed on the TV screen (Menu
Playback). Some of the functions described in this
owner’s manual may not work with some discs.
Title/Chapter/Track
A DVD-Video has large partitions called “Titles”, and
smaller partitions within them called “Chapters”.
A music CD has other partitions called “Tracks”. A number is allotted to each partition and these numbers are
called “title numbers”, “chapter numbers” or “track numbers”.
When recording in the VR mode
One-time recording is set to 1 title (1 chapter). However, if you stop recording temporarily or erase scenes
by editing, the chapter will automatically be partitioned.
The interval between chapters can be specified. (See
page 31.)
When recording in the Video mode
One-time recording is set to 1 title. In recording, chapters are set automatically. The interval between chapters can be specified. (See page 31.)
NOTES:
• The title, chapter and track are numbered, but some
discs may not record the numbers.
• Recording on DVD-R/RW in the Video mode is a new
standard approved at the 2000 DVD forum. Conformity to this standard varies with each DVD player
manufacturer. Some models of DVD player or DVDROM drive, therefore, will not playback recorded videos.
•Toshiba is not liable for any damage or loss caused
directly or indirectly by the malfunction of this DVD/
VCR, including, without limitation, any one of the
following:
•Failure to record contents intended to be recorded
by the consumer.
•Failure to edit contents as intended by the consumer.
• When a DVD-R disc created on this recorder is used
(e.g., insertion, playback, recording or editing) in
another DVD player, recorder or personal computer
drive.
• When a DVD-R disc that is used in the manner
described in the immediately preceding bullet point
is used again in this recorder.
• When a DVD-R disc that was recorded in another
DVD recorder, or in a personal computer drive is
used in this recorder.
• Discs recorded in this recorder may not operate as
expected on other DVD players, recorders or
personal computer drives.
Disc playback in other players
DVD-RW/R recorded in this unit can be finalized. The
disc can be played back in other players that can
playback DVD-RW and DVD-R.
For more information on finalization, see “FINALIZE” in
“Setting the disc” (page 27).
When recording in the VR mode
Even if a DVD-RW disc recorded in the VR mode is
finalized, you can record or edit by cancelling the
finalization. (See “UNDO FINALIZE” on page 28.)
When you playback the disc with another player, make
sure that the DVD player supports DVD-RW.
2G00101A P08-P11 3/7/05, 5:14 PM11
Introduction
12
Parts and functions
Rear
Front
AC power cord
DVD COAXIAL DIGITAL
AUDIO OUT jack
DVD/VCR common
AUDIO (L/R)/VIDEO OUT jacks
DVD AUDIO (L/R)
OUT jacks
DVD/VCR common
AUDIO (L/R)/VIDEO
IN (LINE 1) jacks
DVD S-VIDEO
IN (LINE 1) jack
DVD/VCR common
S-VIDEO OUT jack
DVD COMPONENT
OUT jacks
DVD OPTICAL DIGITAL
AUDIO OUT jack
RF IN jack
RF OUT jack
POWER button
EJECT button
OPEN/CLOSE button
PLAY button
STOP button
FF (Fast Forward) button
REW (Rewind) button
REC/OTR button
CHANNEL
/ buttons
Disc tray
Cassette Loading Slot
DVD button/
DVD indicator
DUBBING button
VCR button/
VCR indicator
Display window
VIDEO IN (INPUT 2) jack
S-VIDEO IN jack
AUDIO (L/R) IN jacks
* This unit has a door on the front panel.
Please open it to access the S-VIDEO jack and the AUDIO (L/R)/VIDEO IN (INPUT 2) jacks.
Remote senser
2G00101A P12-P21 3/7/05, 5:14 PM12
Introduction
13
No. Display Description
Lights during video tape playback.
1
Parts and functions
NOTE:
Some discs may not playback correctly, or chapter number, playback time, etc may not be displayed.
Display window
Video tape is temporarily stopped.
Lights during video tape recording.
Progressive scanning mode.
Timer recording display.
P
P
2
1 3
4
2
4
Appears when a CD is inserted.
Appears when a CD-R is inserted.
Appears when a DVD-Video is inserted.
Appears when a DVD-R is inserted.
Appears when a DVD-RW is inserted.
Appears when a DVD-RW in VR mode is inserted. When the disc is set to video mode, VR does not appear.
Video tape is in the unit.
Clock display (Colon [ : ] flashes).
Counter display in hour/minute/second for VCR/DVD, minute/second for CD.
Cable TV channel display.
TV channel display.
Tr ack number display for CD.
Display for afternoon (out in the morning).
The external input channel (L1 or L2) display.
Error display.
Lights during playback of DVD and CD. Flashes in auto resume.
DVD or CD is temporarily stopped.
Lights during DVD recording.
CD
CD-R
DVD
DVD-R
DVD-RW
VR
10:00
01
H00M00S
C 36CH
2CH
TRK 002
PM
L1/L2
Err
3
4 DVD recording modes. XP, SP, LP or SLP can be selected in turn by pressing the REC MODE/SPEED repeatedly.
2 VCR recording modes. SP or SLP can be selected in turn by pressing the REC MODE/SPEED repeatedly.
SP/SLP
XP/SP/LP/SLP
Appears when a CD-RW is inserted.
CD-RW
Appears when the tuner built into this unit is not selected. When you press TV/VIDEO disappears.
TV
2G00101A P12-P21 3/7/05, 5:14 PM13
Introduction
14
OPEN/CLOSE
Opens or Closes the tray. 33
EJECT
Ejects the cassette tapes 48
PROGRESSIVE Activates the progressive scanning mode. 47
TV/VIDEO Select to operate TV/VIDEO 22, 55
ON/STANDBY Turns power on/off. 22
0-9 Direct channel selection of TV 54
Setting input 37, 74
Entering a password 25
INSTANT REPLAY Repeats playback between the section played
10 seconds before and present section. 38
INSTANT SKIP Skips commercial breaks. 37, 50
DISPLAY Displays VCR or DVD operation status. 35, 51
DVD
VCR
CH / Channel selection for the connected TV or VCR 54
DUBBING Copies VCR to DVD or DVD to VCR. 76
DVD MENU Displays the menu of the DVD disc. 39
INPUT SELECT Switches the connected TV to external inputs. 78
TOP MENU/TITLE MENU
Selects titles of a DVD disc. 34, 39, 42, 62
SETUP Display the setup menu 23,57
/ Cursor buttons 23, 33, 37, 57
TRK +/– Manual tracking in the playback mode for VCR 50
/ Cursor buttons 33, 37
ENTER Option selection in the menu 23, 33, 37, 57
RETURN Close the menu window. 23, 45
CANCEL Deletes the Timer recording program. 59
Cancels input data in the setting mode. 25
PAUSE/STILL Still picture/Recording pause on/off 36, 50
PLAY Playback 33, 49
STOP Stop 33, 49, 55
SKIP / Skips chapters in the forward or reverse direction 36
INDEX – / + Searches for the INDEX mark of a tape 51
SEARCH /REW
Rewind/Review playback 36, 49, 50
SEARCH /F.FWD
Fast Forward/Forward search playback 36, 49, 50
REC MODE/SPEED Selects the recording mode. 54, 56
REC/OTR Recording 54, 56, 78
TIMER REC Sets the unit to start recording at a preset time. 59
SLOW Slow motion playback 36, 50
ANGLE Changes playback angle. 40
COUNTER RESET Resets the counter to 00H 00M 00S . 51
AUDIO Switches sound between mono and stereo. 60
AUDIO SELECT Changes the language of the DVD. 41
SUBTITLE Selects subtitles of the DVD disc. 41
AT R Digital AUTO TRACKING 50
CLOCK/COUNTER Changes the front panel display mode. 51
ZOOM Zoom (for DVD/Video CD) 40
ZERO RETURN Stops the tape when the counter reaches 00H 00M 00S . 51
A-B REPEAT Repeats playback between A and B. 38
PLAY MODE Selects the playback mode. 37
REPEAT Repeats playback. 38, 50
Remote control
Page
Parts and functions
Switches to operation between VCR and DVD. 33,49,76,77
2G00101A P12-P21 3/7/05, 5:14 PM14
Introduction
15
Inserting Batteries into the Remote Control:
Parts and functions
3
Replace the compartment cover.
2
Install two “AAA” batteries, paying attention to the polarity diagram in the battery compartment.
1
Open the battery compartment
cover in the direction of the arrow.
Caution:
Never throw batteries into a fire.
Note:
• Be sure to use AAA size batteries.
• Dispose of batteries in a designated disposal area.
• Batteries should always be disposed of with the environment in mind. Always dispose of batteries in
accordance with applicable laws and regulations.
• If the remote control does not operate correctly, or if the operating range becomes reduced, replace batteries
with new ones.
• When necessary to replace batteries in the remote control, always replace both batteries with new ones.
Never mix battery types or use new and used batteries in combination.
• Always remove batteries from remote control if they are dead or if the remote control is not to be used for an
extended period of time. This will prevent battery acid from leaking into the battery compartment.
Remote control basics
• Press ON/STANDBY to turn the DVD/VCR on or off.
• Press CH
or CH to move through the channels one channel at a time.
• The
/ / / are also used to navigate on-screen menu system.
• You can directly access specific channels using numeric keys.
• Each press of DVD or VCR, switches the screen between the DVD screen (DVD mode) and the VCR screen
(VCR mode).
Operation
• Aim the remote control at the remote sensor and press control buttons to
operate.
• Operate the remote control within 30° angle on either side of the remote
sensor, up to a distance of approximately 7 meters (23 feet).
Polarized AC Cord Plug
(One blade is wider than the other.)
AC Outlet
Wider Hole
and Blade
Power Source
TO USE AC POWER SOURCE
Use the AC polarized line cord provided for operation on AC. Insert the AC
cord plug into a standard 120V 60Hz polarized AC outlet.
NOTES:
•Never connect the AC line cord plug to other than the specified voltage
(120V 60Hz). Use the attached power cord only.
• If the polarized AC cord does not fit into a non-polarized AC outlet, do not
attempt to file or cut the blade. It is the user’s responsibility to have an
electrician replace the obsolete outlet.
• If you cause a static discharge when touching the unit and the unit fails to
function, simply unplug the unit from the AC outlet and plug it back in. The
unit should return to normal operation.
• If the AC cord plug is plugged in for the first time, wait for approximate 3
minutes before operating the unit.
Approx.7 meters (23 feet)
2G00101A P12-P21 3/7/05, 5:14 PM15
Introduction
16
NOTES: • A clear picture will not be obtained by the DVD/VCR unless the antenna signal is good. Connect the
antenna to the DVD/VCR properly.
• For better quality recording, an indoor antenna or a telescopic antenna is not recommended. The use
of an outdoor type antenna is required.
• If you are not sure about the connection, please refer to qualified service personnel.
If you are using an antenna system, follow these instructions. If you are a Cable TV subscriber, skip ahead
to page 18 for the proper connections.
ANTENNA TO DVD/VCR CONNECTION
The DVD/VCR must be connected “between” the antenna and the TV. First, disconnect the antenna from the TV
and connect it to the DVD/VCR. Then connect the DVD/VCR to the TV. Below are 3 common methods of connecting an antenna system to a DVD/VCR. Find the type of antenna system you are using and follow the connection
diagram.
If both UHF and VHF antennas have 300 ohm twin lead (flat) wires,
use a combiner having two 300 ohm inputs and one 75 ohm output.
NOTE:
Antenna connections
Combination UHF/VHF antenna with 75 ohm coaxial cable
Combination UHF/VHF antenna with 300 ohm twin lead (flat) wire
Separate UHF and VHF antennas
1
2
3
DVD/VCR
300 ohm twin lead (flat) wire
75
(su
Matching transformer
300 ohm input
75 ohm output
(not supplied)
DVD/VCR
300 ohm twin lead (flat) wire
75 ohm coaxial cable
UHFVHF
7
(s
Combiner
75/300 ohm input
75 ohm output
(not supplied)
DVD/VCR
75 ohm coaxial cable
75
2G00101A P12-P21 3/7/05, 5:14 PM16
Introduction
17
NOTE: If a UHF or VHF antenna is used,
set the TV/CABLE menu option
to the “TV” mode.
TV with single 75 ohm UHF/VHF antenna
input
NOTE: If a UHF or VHF antenna is used,
set the TV/CABLE menu option
to the “TV” mode.
TV with 300 ohm UHF and 75 ohm VHF
antenna inputs
NOTE: If a UHF or VHF antenna is used,
set the TV/CABLE menu option to
the “TV” mode.
TV with 300 ohm UHF and 300 ohm VHF
antenna inputs
DVD/VCR TO TV CONNECTION
After you have connected the antenna to the DVD/VCR, you must connect the DVD/VCR to the TV.
Below are 3 common methods of connecting your DVD/VCR to a TV. Find the type of TV you are using and follow
the connection diagram.
This DVD/VCR has a single 75 ohm output for connection to a TV. If your TV has separate UHF and VHF antenna
inputs (numbers 2 and 3 below), use a splitter to connect the DVD/VCR to the TV for UHF and VHF reception.
Antenna connections
UHF
VHF
TV
75 ohm coaxial cable
(supplied)
Splitter
75 ohm input
75/300 ohm outputs
(not supplied)
UHF
VHF
TV
75 ohm coaxial cable
(supplied)
Splitter
75 ohm input
300 ohm outputs
(not supplied)
UHF/VHF IN
TV
75 ohm coaxial cable (supplied)
The unauthorized recording, use, distribution, or revision of television programs, videotapes, DVDs and other
materials, is prohibited under the Copyright Laws of the United States and other countries, and may subject
you to civil and/or criminal liability.
2G00101A P12-P21 3/7/05, 5:14 PM17
Introduction
18
UHF/VHF
IN (ANT)
TV
DVD/VCR
Incoming cable
Converter/
descrambler
UHF/VHF
IN (ANT)
TV
DVD/VCR
Incoming
cable
Converter/
descrambler
Many cable companies offer services permitting reception of extra channels including pay or subscription channels. This DVD/VCR has an extended tuning range and can be tuned to most cable channels without using a cable
company supplied converter box, except for those channels which are intentionally scrambled. If you subscribe to
a special channel which is scrambled, you must have a descrambler box for proper reception.
Cable TV connections
NOTE: Whenever a converter/descrambler box is placed before the DVD/VCR, you must tune the DVD/VCR to the
output of the converter/descrambler box, usually channel 3 or 4.
ALLOWS: • Recording of nonscrambled channels.
• Use of the programmable timer.
• Recording of one channel while watching another.
ALLOWS: • Recording of channels through the converter box
(scrambled and unscrambled).
• Using the programmable timer to record only the
channel selected at the converter box.
PREVENTS: • Recording one channel while watching another.
• Using the DVD/VCR tuner to select channels.
1
2
3
ALLOWS: • Recording of nonscrambled channels.
• Use of the programmable timer.
• Recording an unscrambled channel while watch-
ing any channel selected at the converter box.
PREVENTS: Recording scrambled channels.
NOTE:
If you are playing a tape or using the
tuner built into the DVD/VCR, the converter must be set to the video channel
output of the DVD/VCR (either 3 or 4).
NOTE:
To record from converter/descrambler,
DVD/VCR tuner must be tuned to the
converter output channel, usually channel 3 or 4.
UHF/VHF
IN (ANT)
TV
DVD/VCR
Incoming cable
2G00101A P12-P21 3/7/05, 5:14 PM18
Introduction
19
UHF/VHF
IN (ANT)
TV
DVD/VCR
Incoming
cable
Splitter
Converter/descrambler
A/B switch
UHF/VHF
IN (ANT)
TV
DVD/VCR
Incoming
cable
Splitter
Converter/
descrambler
A/B switch
IMPORTANT: Make sure the TV/CABLE menu option is set to the “CABLE” mode.
This DVD/VCR cannot receive scrambled programs since it does not contain a descrambler. In order to receive scrambled
programs, your existing descrambler must be used. Descrambler boxes are available from cable companies. Consult your
local cable company for more information concerning connection to their descrambler equipment. There are many ways
to connect your DVD/VCR to a cable system. Below are six common methods of connection.
4
5
6
ALLOWS: • Recording of one channel while watching another.
• Using the programmable timer to record only the channel selected at the converter box.
• Recording of all channels through the converter box.
PREVENTS: • Watching scrambled channels while recording another channel.
• Using the DVD/VCR tuner to select channels.
ALLOWS: •Recording of nonscrambled channels.
•Recording of one channel while watching another.
•Watching premium channels through the converter while recording nonscrambled channels.
•Using the programmable timer.
PREVENTS: Recording scrambled channels.
ALLOWS: • Recording of all channels through the converter box.
• Recording a scrambled or unscrambled channel while watching another (scrambled or
unscrambled) channel.
• Using the programmable timer to record only the channel selected at the converter box.
PREVENTS: Using the DVD/VCR tuner to select channels.
Cable TV connections
UHF/VHF
IN (ANT)
TV
DVD/VCR
Incoming
cable
Splitter
Converter/descrambler
A/B switch
Converter/
descrambler
The unauthorized recording, use, distribution, or revision of television programs, videotapes, DVDs and other
materials, is prohibited under the Copyright Laws of the United States and other countries, and may subject
you to civil and/or criminal liability.
2G00101A P12-P21 3/7/05, 5:14 PM19
Introduction
20
Connections with the TV or audio component
The exact arrangement you use to interconnect various video
and audio components to the DVD/VCR is dependent on the
model and features of each component. Check the Owner’s
Manual provided with each component for the location of video
and audio inputs and outputs.
Connect to a TV with Audio/Video output
You can enjoy playback by connecting the unit to a TV.
Connect the unit to a TV equipped with audio input (L/R) and video input jacks using the supplied audio/video cable.
Connect to a TV with S-Video output
If your TV has an S-Video input, you can get higher quality by connecting it with the S-Video output of the unit using
the S-Video cable instead of connecting the video input of the TV to the video output jack of the unit.
Connect to a TV with Component video output (for DVD/CD playback)
You can enjoy the highest quality picture by connecting the unit’s component video out jacks to the component
video input jacks of your TV, with component video cables (not supplied).
NOTES:
• When connecting to a TV using the video or S-Video jack, make sure that the progressive indicator on the
display window is not lit. If it is lit, the video and S-Video outputs do not feed the correct signals and you cannot
see any picture. To turn off the progressive indicator, make the progressive scanning mode inactive (see page
47).
• If the component video input jacks on a TV are the BNC type, use an adapter to convert the RCA jacks from the
component video cables to BNC (not supplied).
To Audio (R) input
Audio/video cable (supplied)
Audio (R) output
To Audio (L) input
Audio (L) output
To Video input
Video output
TV
DVD/VCR
To Audio (R) input
Audio cable (not supplied)
DVD audio (R) output
DVD audio (L) output
S-Video output
To S-Video
input
S-Video cable (not supplied)
To Audio (L) input
TV
DVD/VCR
To Audio (R) input
Audio cable (not supplied)
DVD audio (R) output
To Audio (L) input
DVD audio (L) output
TV
DVD/VCR
Component video cable (not supplied)
Component
video output
To Component
video input
The unauthorized recording, use, distribution,
or revision of television programs, videotapes,
DVDs and other materials, is prohibited under
the Copyright Laws of the United States and
other countries, and may subject you to civil
and/or criminal liability.
2G00101A P12-P21 3/7/05, 5:14 PM20
Introduction
21
Connections with the TV or audio component
Connect to a stereo amplifier with audio output
You can enjoy high quality audio by connecting the audio output to your amplifier.
Connect the audio output jacks to any line-level inputs (such as AUX, DVD, CD, etc.) of an audio amplifier.
Connect to an AV Amplifier with built-in digital surround
If you are using an Amplifier with a built-in digital surround as follows, you can enjoy the various audio systems
such as Dolby Digital and DTS by using the optical or coaxial digital output.
Use this connection to connect an:
•AV amplifier with built-in *Dolby Digital decoder
•AV amplifier with built-in *DTS decoder
Connecting the optical digital cable
You may connect to an AV Amplifier with an optical digital cable (not supplied) instead of a coaxial digital
cable.
When you connect the optical digital cable (not supplied), remove the dust protection cap from the rear panel.
When not using the optical digital cable, attach the dust protection cap to protect against dust.
NOTES:
• The DVD OUTPUT jacks (OPTICAL, COAXIAL, AUDIO L/R and COMPONENT) are useful only for DVD
section. The VHS signal is output only from the S-Video output jack, composite jacks (DVD/VCR OUTPUT)
and UHF/VHF OUT.
• When you make the connections above, do not set DOLBY DIGITAL to DOLBY DIGITAL or DTS to ON on the AV
amplifier. If you do, a loud noise will suddenly come out from the speakers, affecting your ears or causing the
speakers to be damaged.
• Caution for the optical digital audio output connector: Do not connect to an amplifier (with an optical digital input
connector) which does not contain a Dolby Digital or DTS decoder. Otherwise, any attempt to play DVDs may
cause such a high level of noise that it may be harmful to your ears and damage your speakers.
• DTS audio will be output only from the COAXIAL or OPTICAL output. To hear DTS audio, DTS-Decoder is
necessary.
• When playing DTS-encoded CDs, only noise will be heard from the speakers or analog stereo outputs.
• Some DTS decoders which do not support DVD-DTS interface may not work properly with the unit.
• The optical or coaxial digital output jack output sounds in the bitstream.
NOTE:
You may connect to a TV with a component
video cable (not supplied) or S-Video cable
(not supplied) instead of a video cable (not
supplied).
To Audio (R) input
Audio cable (not supplied)
Audio (R) output
To Audio (L) input
Audio (L) output
Stereo Amplifier
DVD/VCR
DVD/VCR
AV Amplifier with built-in various
decoder as above
Video output
To Video intput
Coaxial digital audio output
Coaxial digital
cable (not supplied)
Video cable (not supplied)
TV
2G00101A P12-P21 3/7/05, 5:14 PM21
22
Introduction
Auto clock setting / Setting the video channel
NOTES:
• When shipped from factory, the
video channel is set to CH 3.
• If the unit does not operate properly, or there is no key operation
from the unit and/or the remote
control: Static electricity, etc., may
affect the operation. Disconnect
the AC power cord once, then connect it again.
Auto clock setting
Preparation:
You must connect the antenna or cable before connecting the AC cord
to the power source.
Wait at least 3 minutes with the power turned off, after the antenna or
cable is connected, for the auto clock feature to activate.
After the clock is set automatically, you may have to set the time zone
and daylight saving time. (See page 26.)
Press ON/STANDBY to turn on the DVD/VCR after the auto clock op-
eration completed.
• When shipped from factory, the “AUTO CLOCK” option is set to “ON”
position.
• If you turn the DVD/VCR on during auto clock setting, the clock is not
set.
• Dependimg on the reception condition, auto clock setting may take
approx. 30 minutes.
• After a power failure or disconnection of the power plug, the clock will
be lost. In this case, wait 3 minutes before turning the DVD/VCR on.
• With cable box connection, if the auto clock setting is unsuccessful,
select the PBS channel carrying the XDS information, then turn the
DVD/VCR off. After 3 minutes, turn the DVD/VCR on.
• If the clock is not set automatically, set the clock manually. (See page
26.)
Setting the video channel
To view playback of a recorded tape or DVD disc, or to watch a
program selected by the VCR’s channel selector, the TV must be
set to channel 3 or 4 (video channel).
When a TV is connected with the 75 ohm coaxial cable only:
1
Press and hold 3 or 4 on the remote control for 3 seconds in the
standby mode to select CH 3 or 4. The selected channel number
will flash on the display for about 4 seconds.
2
Tu rn ON the TV and set to CH 3 or 4 to correspond with the chan-
nel selected in step 1.
3
Press ON/STANDBY to turn on the DVD/VCR.
4
Press TV/VIDEO to select the VIDEO position.
The TV indicator will disappear in the display.
5
Select any channel to receive a TV station in your area.
The channel number will appear on the screen for about 4 seconds.
For a push-button TV tuner
If CH 3 or 4 corresponding to the video channel cannot be tuned on
your TV, proceed as follows: set the VCR 3/4 channel selector and the
TV to CH 3 or 4, playback a prerecorded tape and tune the TV to receive a sharp color picture from the video cassette recorder. Refer to
your TV owner’s manual for details.
2G00101A P22-P32 3/7/05, 5:14 PM22
23
Various settings
SETUP MENU
The SETUP MENU consists of several menus where
you can make various settings concerning language, audio functions, and images. In addition, this
menu includes a clock, channel and other things
that require setting just after purchase.
For details of each menu, see the corresponding
section in this chapter.
Using the SETUP MENU
The following example shows the basic setting procedure of the SETUP MENU. The remote control keys
that operate the SETUP MENU are displayed at the
bottom of the screen.
1
Press SETUP while the DVD or video tape is
stopped.
The SETUP MENU screen will appear.
2
Press or to select the desired menu and press
ENTER.
The submenu screen of the selected menu will appear.
3
Press or to select the desired submenu and
press ENTER.
The screen for the selected submenu will appear.
4
Press or to select the desired item you want,
and press ENTER.
Selectable items will be listed.
5
Press or to select the desired item and press
ENTER.
This completes the setting procedure.
• To return to the previous screen, press RETURN.
• To close the SETUP MENU, press SETUP.
NOTES:
• For items that require different operations from the
basic setting procedure, the setting procedure is described in each individual section.
• The item which is indicated by blue color cannot be
selected.
• “TIMER REC SET” cannot be selected when the
clock is not set.
TIMER REC SET
SYSTEM SETUP
AV SETUP
REC SETUP
CH SETUP
OTHER
SETUP MENU
RETURN SETUPENTERENTER BACK END
SELECT
TIMER REC SET
SYSTEM SETUP
AV SETUP
REC SETUP
CH SETUP
OTHER
LANGUAGE
PARENTAL
CLOCK
DISC SETUP
OTHER
SETUP MENU
RETURN SETUPENTER BACK END
SELECT
ENTER
TIMER REC SET
SYSTEM SETUP
AV SETUP
REC SETUP
CH SETUP
OTHER
LANGUAGE
OSD LANGUAGE
DVD MENU
AUDIO
SUBTITLE
SETUP MENU
RETURN SETUPENTER BACK END
ENGLISH
ENGLISH
AUTOMATIC
ENGLISH
SELECT
ENTER
TIMER REC SET
SYSTEM SETUP
AV SETUP
REC SETUP
CH SETUP
OTHER
LANGUAGE
OSD LANGUAGE
DVD MENU
AUDIO
SUBTITLE
SETUP MENU
RETURN SETUPENTER BACK END
ENGLISH
ENGLISH
AUTOMATIC
ENGLISH
SELECT
ENGLISH
FRANCAIS
ESPANOL
OTHER
AUTOMATIC
OFF
----
ENTER
Various settings
2G00101A P22-P32 3/7/05, 5:14 PM23
Various settings
24
Setting the language
You can choose the language of the menu screen,
DVD menu, DVD audio and subtitles.
Preparation:
• Turn ON the TV and set it to the video input mode.
• Select “LANGUAGE” from “SYSTEM SETUP”. For
the procedure, see steps 1 to 3 in “Using the SETUP
MENU” on page 23.
Selectable languages:
ENGLISH, FRANCAIS, ESPANOL
The language you have selected will play if it is recorded on the disc.
ORIGINAL
The unit will select the first priority language of each
disc.
OTHER
If you want to select another language, before pressing ENTER, input the language code by using the
numeric keys. (See the Language code list on page
81). Then press ENTER.
• If you input a wrong number, press CANCEL.
NOTE:
If the selected language is not recorded on the disc,
the first-priority language is selected.
SUBTITLE
When several subtitles languages are recorded on DVD,
you can select the language to be used for the subtitles. The selected language remains in effect after the
power is turned off or the disc is replaced.
Select “SUBTITLE” and select the menu language from
the below.
Selectable languages:
ENGLISH, FRANCAIS, ESPANOL
The subtitle is displayed with the selected language
if it is recorded on the disc.
OTHER
If you want to select another language, before pressing ENTER, input the language code by using the
numeric keys. (See the Language code list on page
81). Then press ENTER.
• If you input a wrong number, press CANCEL.
AUTOMATIC
• The unit will automatically select the same language in the AUDIO setting.
• When the unit selects the same language as the
AUDIO setting, the subtitles will not appear during playback.
• When you do not use the same language as the
AUDIO setting, the subtitles will appear during
playback.
OFF
Subtitles do not appear.
NOTE:
If the selected language is not recorded on the disc,
the first-priority language is selected.
OSD LANGUAGE
You can set the language for on screen display.
Select “OSD LANGUAGE” and select the language from
the below.
Selectable languages:
ENGLISH, FRANCAIS, ESPANOL
DVD MENU
When several menu languages are recorded on a DVD,
you can select the language to be used for the DVD
menu.
Select “DVD MENU” and select the language from the
below.
Selectable languages:
ENGLISH, FRANCAIS, ESPANOL
The selected language is the first priority menu language.
OTHER
If you want to select another language, before pressing ENTER, input the language code by using the
numeric keys. (See the Language code list on page
81). Then press ENTER.
• If you input a wrong number, press CANCEL.
AUDIO
When several audio languages are recorded on a DVD,
you can select the audio language to be played back.
The selected language remains in effect after the power
is turned off or the disc is replaced.
Select “AUDIO” and select the audio language from the
below.
TIMER REC SET
SYSTEM SETUP
AV SETUP
REC SETUP
CH SETUP
OTHER
LANGUAGE
OSD LANGUAGE
DVD MENU
AUDIO
SUBTITLE
SETUP MENU
RETURN SETUPENTER BACK END
ENGLISH
ENGLISH
AUTOMATIC
ENGLISH
SELECT
ENTER
2G00101A P22-P32 3/7/05, 5:14 PM24
25
Various settings
Setting the parental control
Some discs are specified as not suitable for children. This unit can prevent playback of such discs.
Preparation:
• Turn ON the TV and set it to the video input mode.
• Select “PARENTAL” from “SYSTEM SETUP”. For
the procedure, see steps 1 to 3 in “Using the SETUP
MENU” on page 23.
NOTES:
• The selected level will apply to operations executed
after this.
• The unit cannot restrict playback of some discs.
• Some discs may not be encoded with specific rating
level information though its disc jacket says “adult”.
Parental control will not work with those discs.
• If you forget your password, open the disc tray; if there
is a disc inside then remove it and close the tray. To
reset the code press and hold number 7 on the remote control, then press and hold STOP on the front
panel at the same time. The On-Screen Display will
show “PARENTAL UNLOCK”. You can now set a new
password.
Temporarily cancelling parental control
Parental control can temporarily be cancelled with some
DVDs.
1
Playback a DVD. (See page 33.)
2
If the DVD disc has been designed to temporarily
cancel the rating level, the screen that follows the
“READING” screen will change. If you select “YES”
with the ENTER, the message “YOUR DISC EXCEEDS THE PARENTAL CONTROL LEVEL
1.”(e.g.) will then appear.
3
If you wish to cancel the set rating level temporarily,
select “PARENTAL CONTROL LEVEL” with
or
, then press ENTER. If the password has been
selected, the password input screen will appear.
Alternatively, if the password has not been set, playback will commence. If you don’t know (or have
forgotten) the password, select “CANCEL PICTURE”.
The setting screen will disappear. Press OPEN/
CLOSE to remove the disc.
4
Use the numeric keys to input the password.
•To interrupt the input process, press RETURN.
5
Press ENTER.
6
Playback will commence if the entered password
was correct.
NOTE:
This temporary cancellation of the rating level will remain active until the disc is ejected.
When the disc is ejected, the original rating level will be
set again automatically.
Selecting parental control
Select “PARENTAL” and select the parental control level
from the below.
Level Off: Parental control is turned off.
Level 1:
Adult discs and general discs (R-rated
discs included) cannot be played back.
Level 2 to 3: Adult discs and R-rated discs cannot
be played back.
Level 4 to 7: Adult discs cannot be played back.
(Level 4 to 7 discs contain content children age 15 and younger may not see.)
Level 8:Virtually all discs can be played back
without restriction.
Select from level 1 to level 8.
On a scale of 1- 8, “1” is the most restrictive.
To lock the selected parental control level
1
To lock the selected parental control level, press
or to select “PASSWORD”.
2
Use the numeric keys to input a 4-digit password.
• If you input a wrong number, press CANCEL.
• Be sure to remember this number!
3
Press ENTER.
To cancel the locked parental control level
1
Select “PASSWORD” shown in step 1 of the above
section and use the numeric keys to input the password.
2
Press ENTER.
The locked mark
“
”
will change to an unlocked
mark “
”.
Then, you can change the parental control level,
or enter a new password.
TIMER REC SET
SYSTEM SETUP
AV SETUP
REC SETUP
CH SETUP
OTHER
LANGUAGE
PARENTAL
CLOCK
DISC SETUP
OTHER
PARENTAL
PASSWORD
PARENTAL
SETUP MENU
RETURN SETUPENTER BACK END
DELETECANCEL
- - - -
INPUT NO.
09
SELECT
PARENTAL
OFF
ENTER
----
change to
1234
YOUR DISC EXCEEDS THE PARENTAL
CONTROL LEVEL 1.
PARENTAL CONTROL LEVEL
CANCEL PICTURE
2G00101A P22-P32 3/8/05, 7:07 PM25
Various settings
26
Setting the clock
The clock is set to the correct time automatically,
but it can also be set manually. The clock can be set
for daylight saving time and time zone.
Preparation:
• Turn ON the TV and set it to the video input mode.
• Select “CLOCK” from “SYSTEM SETUP”. For the procedure, see steps 1 to 3 in “Using the SETUP MENU”
on page 23.
CLOCK (manually)
You can manually set the date, year and present time
with the remote control.
Ex.: Setting the clock to “10:20AM” March, 30th, 2005.
1
Select “CLOCK” and press ENTER.
2
Select the desired items using or (month,
date, year, hour, minute and AM/PM), then press
ENTER.
3
Press or to set the value of the selected item.
4
Repeat steps 2 and 3 to set the date, year and
present time, and press ENTER. The SETUP
MENU will close.
This completes clock time setting.
AUTO CLOCK
You can automatically set the clock by turning “ON” the
AUTO CLOCK function.
When you want to set the auto clock function to “OFF”,
select “AUTO CLOCK”, press ENTER and select “OFF” .
For more information see page 22.
/01/05 12:00AM 01
03/30/05 10:20AM
0
STANDARD TIME (Time zone)
In the rare event that you live within the broadcast range
of two stations in two different time zones, the DVD/
VCR may recognize the wrong station for the auto clock
set. To correct the situation:
Select “STANDARD TIME” and select the time zone from
the below.
Selectable time zones and correction times
ATLANTIC: GMT – 4 hours
(GMT: Greenwich Mean Time)
EASTERN: GMT – 5 hours
CENTRAL: GMT – 6 hours
MOUNTAIN: GMT – 7 hours
PACIFIC: GMT – 8 hours
ALASKA: GMT – 9 hours
HAWAII: GMT – 10 hours
AUTOMATIC:AUTO SET
NOTES:
• When shipped from the factory, the “STANDARD
TIME” is set to “AUTOMATIC”.
• After making the auto clock setting, in some cases
the clock may display another time zone. You can correct the clock by selecting your time zone setting
above.
• When the clock is not set or you set the clock manually, the time zone setting is not available.
DAYLIGHT SAVING TIME
You can set the clock to daylight saving time automatically or manually.
To select daylight saving time, select “DAYLIGHT SAVING TIME” and select “ON”, while to cancel the daylight saving time, select “OFF”.
ON:For manual setting (forward 1 hour)
OFF:For manual setting (back 1 hour)
AUTOMATIC:For automatic setting (read XDS in the
signal)
NOTES:
• When you want to set daylight saving time, on the
first Sunday in April you set it to “ON”, and on the last
Sunday in October you set it to “OFF”.
• When shipped from the factory, the “DAYLIGHT SAVING TIME” option is set to “AUTOMATIC”.
• When the clock is not set, the daylight saving time
setting is not available.
• When there is no daylight saving time in your area,
always select “OFF”.
TIMER REC SET
SYSTEM SETUP
AV SETUP
REC SETUP
CH SETUP
OTHER
CLOCK
CLOCK (MM/DD/YY)
AUTO CLOCK
STANDARD TIME
DAYLIGHT SAVING TIME
ON
AUTOMATIC
AUTOMATIC
01/01/05 12:00AM
SETUP MENU
RETURN SETUPENTER BACK END
SELECT
SELECT
ENTER
2G00101A P22-P32 3/7/05, 5:14 PM26
27
Various settings
Setting the disc
TIMER REC SET
SYSTEM SETUP
AV SETUP
REC SETUP
CH SETUP
OTHER
DISC SETUP
REFORMAT AS DVD VIDEO
REFORMAT AS DVD VR
NEW DISC FORMAT
FINALIZE
PROTECT DISC
UNDO FINALIZE
PROCEED
VR
PROCEED
OFF
PROCEED
PROCEED
SETUP MENU
RETURN SETUPENTERENTER BACK END
SELECT
REFORMAT
START CANCEL
FINALIZING
PLEASE WAIT
REFORMAT
FINALIZE
START CANCEL
NEW DISC FORMAT
START CANCEL
INITIALIZING DISC
You can format, protect, or finalize a disc.
Preparation:
• Turn ON the TV and set it to the video input mode.
• Select “DISC SETUP” from “SYSTEM SETUP”. For
the procedure, see steps 1 to 3 in “Using the SETUP
MENU” on page 23.
REFORMAT
You can format a recorded DVD-RW.
Check the content of the disc before format. If you format the disc, the recorded content of the disc will be
erased.
To format a disc in the Video mode, select “REFORMAT AS DVD VIDEO”, and to format it in the VR mode,
select “REFORMAT AS DVD VR”. The screen below
will appear.
• When you select “START” and press ENTER, format
will start. The screen below will appear.
• When you select “CANCEL” and press ENTER, the
DISC SETUP screen will appear.
NOTES:
•You cannot format Ver. 1.0 DVD-RW and DVD-R.
•You cannot format a disc if the disc protection is “ON”.
In such a case, be sure to cancel the disc protection
(see page 28) before format.
NEW DISC FORMAT
If you insert an unused DVD-RW disc, the disc is automatically formatted.
If you use the DVD-RW (Ver.1.1/1.2), you can select
the mode to be used for automatic format.
Select “NEW DISC FORMAT” and select the mode from
the list below.
VR:Format the disc in the VR mode.
VIDEO:Format the disc in the Video mode.
When you insert an unused disc, the following message screen will appear.
• When you select “START” and press ENTER, format
will start. The screen below will appear.
• When you select “CANCEL” and press ENTER, the
normal TV screen will appear.
NOTE:
If a recorded disc has scratches or contamination on it,
the “NEW DISC FORMAT” screen may appear.
If this happens, select “CANCEL”.
FINALIZE
To play a DVD disc recorded on this unit you must finalize
the disc to insure compatibility with other DVD players. In
addition if you are using a DVD-RW disc you must record
in Video mode.
When “FINALIZE” is selected, the screen below will
appear.
• When you select “START” and press ENTER, final-
ization will start. The screen below will appear.
• When you select “CANCEL” and press ENTER,
the DISC SETUP screen will appear.
2G00101A P22-P32 3/7/05, 5:14 PM27
Loading...