How it Works
Topcom
Loading...
WBR 7101GMR
User Manual
98 pgs3.19 Mb0

Topcom WBR 7101GMR User Manual

Skyr@cer WBR 7101gmr
Full User Guide
1
Introduction....................................................................................................................... 4
Features.............................................................................................................................. 4
Minimum Requirements .................................................................................................. 4
Package Content ............................................................................................................... 4
Note .................................................................................................................................... 4
Get to know the Broadband Router................................................................................ 5
Front Panel ........................................................................................................................ 6
Setup Diagram...................................................................................................................7
Getting started................................................................................................................... 8
Quick Setup .....................................................................................................................16
Step 1) Time Zone........................................................................................................... 16
Step 2) Broadband Type................................................................................................. 17
1.1 Cable Modem ............................................................................................................ 18
1.2 Fixed-IP xDSL........................................................................................................... 19
1.3 PPPoE ........................................................................................................................ 20
1.4 PPTP .......................................................................................................................... 22
1.5 L2TP........................................................................................................................... 24
1.6 Telstra Big Pond........................................................................................................ 27
General Settings .............................................................................................................. 28
2.1 System ........................................................................................................................ 30
2.1.1 Time Zone............................................................................................................... 31
2.1.2 Password Settings .................................................................................................. 31
2.1.3 Remote Management............................................................................................. 33
2.2 WAN........................................................................................................................... 35
2.2.1 Dynamic IP ............................................................................................................. 36
2.2.2 Static IP Address.................................................................................................... 36
2.2.3 PPPoE (PPP over Ethernet).................................................................................. 36
2.2.4 PPTP ....................................................................................................................... 36
2.2.5 L2TP........................................................................................................................ 36
2.2.6 Telstra Big Pond..................................................................................................... 36
2.2.8 DDNS....................................................................................................................... 38
2.3 LAN ............................................................................................................................ 39
2.4 Wireless...................................................................................................................... 41
2.4.1 Basic Settings.......................................................................................................... 42
2.4.2 Advanced Settings.................................................................................................. 47
2.4.3 Security ................................................................................................................... 49
2.4.3.1 WEP only ............................................................................................................. 49
2.4.3.2 802.1x only ........................................................................................................... 51
2.4.3.3 802.1x WEP Static key........................................................................................ 52
2.4.3.4 WPA Pre-shared key .......................................................................................... 53
2.4.3.5 WPA Radius ........................................................................................................ 55
2.4.4 Access Control........................................................................................................ 56
2
2.5 QoS ............................................................................................................................. 56
2.6 NAT ............................................................................................................................ 60
2.6.1 Port Forwarding .................................................................................................... 62
2.6.2 Virtual Server......................................................................................................... 64
2.6.3 Special Applications............................................................................................... 67
2.6.4 UPnP Settings......................................................................................................... 70
2.6.5 ALG Settings .......................................................................................................... 71
2.6.6 Static Routing......................................................................................................... 72
2.7 Firewall ...................................................................................................................... 74
2.7.1 Access Control........................................................................................................ 75
2.7.2 URL Blocking......................................................................................................... 80
2.7.3 DoS (Denial of Service).......................................................................................... 81
2.7.4 DMZ ........................................................................................................................ 82
Status................................................................................................................................ 83
3.1 Status and Information ............................................................................................ 84
3.2 Internet Connection.................................................................................................. 85
3.3 Device Status ............................................................................................................. 86
3.4 System Log................................................................................................................. 87
3.5 Security Log............................................................................................................... 88
3.6 Active DHCP Client.................................................................................................. 89
3.7 Statistics ..................................................................................................................... 90
Tool................................................................................................................................... 91
4.1 Configuration Tools.................................................................................................. 92
4.2 Firmware Upgrade ................................................................................................... 93
Appendix A......................................................................................................................95
Glossary ......................................................................................................................... 96
3
Introduction
Congratulations on purchasing this Wireless Broadband Router. This Wireless Broadband Router is a cost-effective IP Sharing Router that enables multiple users to share the Internet through an ADSL or cable modem. Simply configure your Internet connection settings in the Wireless Broadband Router and plug your PC to the LAN port and you're ready to share files and access the Internet. As your network grows, you can connect another hub or switch to the router’s LAN ports, allowing you to easily expand your network. The Wireless Broadband Router is embedded with a IEEE 802.11g/b MIMO access point that allows you to build up a wireless LAN. The Wireless Broadband Router provides a total solution for the Small and Medium-sized Business (SMB) and the Small Office/Home Office (SOHO) markets, giving you an instant network today, and the flexibility to handle tomorrow's expansion and speed.
Features
x High Internet Access throughput (50M) x Allow multiple users to share a single Internet line x Supports up to 253 users x Internet Access via Cable or xDSL modem x Access Private LAN Servers from the Public Network x Equipped with four LAN ports (10/100M) and one WAN port (10/100M) x Provides IEEE 802.11g/b MIMO wireless LAN access point x Support DHCP (Server/Client) for easy setup x Support advance features such as: Special Applications, DMZ, Virtual Servers, Access
Control, Firewall.
x Allow you to monitor the router’s status such as: DHCP Client Log, System Log, Security
Log and Device/Connection Status
x Easy to use Web-based GUI for configuration and management purposes
x Remote Management allows configuration and upgrades from a remote site (over the
Internet)
Minimum Requirements
x One External xDSL (ADSL) or Cable modem with an Ethernet port (RJ-45) x Network Interface Card (NIC) for each Personal Computer (PC)
x PCs with a Web-Browser (Internet Explorer 4.0 or higher, or Netscape Navigator 4.7 or
higher)
Package Content
x One 4-port Broadband router unit x One Quick Installation Guide x One User Manual CD x One Power Adapter
x Accessories
Note
The WAN “idle timeout” auto-disconnect function may not work due to abnormal activities of some network application software, computer virus or hacker attacks from the Internet. For example, some software sends network packets to the Internet in the background, even when you are not using the Internet. So please turn off your computer when you are not using it. This function also may not work with some ISP. So please make sure this function can work properly when you use this function in the first time, especially your ISP charge you by time used.
4
Get to know the Broadband Router
Back Panel
The diagram (fig1.0) below shows the broadband router’s back panel. The router’s back panel is divided into three sections, LAN, WAN and Reset:
Figure 1.0
1) Local Area Network (LAN)
The Broadband router’s 4 LAN ports are where you connect your LAN’s PCs, printer servers,
hubs and switches etc.
2) Wide Area Network (WAN)
The WAN port is the segment connected to your xDSL or Cable modem and is linked to the Internet.
3) Reset
The Reset button allows you to do one of two things.
1) If problems occur with your router, press the router’s reset button with a pencil tip (for less than 4 seconds) and the router will re-boot itself, keeping your original configurations.
2) If problems persist or you experience extreme problems or you forgot your password, press the reset button for longer than 4 seconds and the router will reset itself to the factory default settings (warning: your original configurations will be replaced with the factory default settings)
5
Front Panel
On the router’s front panel there are LED lights that inform you of the router’s current status. Below is an explanation of each LED and its description.
LED Light Status Description
PWR
WAN 10/100M
ON Router’s power supply is on
ON WAN port 100Mbps is connected Off WAN port 10Mbps is connected
WAN LNK/ACT ON WAN is connected
Off No WAN connection
Flashing WAN port has Activity (ACT), data being sent
LAN 10/100M ON
(Port 1-4) Off LAN port 10Mbps is connected
LAN port 100Mbps is connected
LAN LNK/ACT ON LAN is connected
(Port 1-4)
WLAN-G ON Wireless LAN has been activated Off Wireless LAN is disabled
Off No LAN connection
Flashing LAN port has Activity (ACT), data being sent
Flashing Wireless LAN has Activity (ACT) data being sent
6
Setup Diagram
Figure 1.2 below shows a typical setup for a Local Area Network (LAN).
Figure 1.2
7
Getting started
This is a step-by-step instruction on how to start using the router and get connected to the Internet.
1) Setup your network as shown in the setup diagram above (fig 1.2).
2) You then need to set your LAN PC clients so that it can obtain an IP address automatically.
All LAN clients require an IP address. Just like an address, it allows LAN clients to find one another. (If you have already configured your PC to obtain an IP automatically then proceed to step 3, page 11)
Configure your PC to obtain an IP address automatically
By default the broadband router’s DHCP is on, this means that you can obtain an IP address automatically once you’ve configured your PC to obtain an IP address automatically. This section will show you how to configure your PC’s so that it can obtain an IP address automatically for either Windows 95/98/Me, 2000 or NT operating systems. For other operating systems (Macintosh, Sun, etc.), follow the manufacturer’s instructions. The following is a step-by-step illustration on how to configure your PC to obtain an IP address automatically for 2a) Windows 95/98/Me, 2b) Windows XP, 2c) Windows 2000 and 2d)
Windows NT.
2a) Windows 95/98/Me
1: Click the Start button and select Settings, then click Control Panel. The Control Panel window will appear.
2: Double-click Network icon. The Network window will appear.
3: Check your list of Network Components. If TCP/IP is not installed, click the Add button to install it now. If TCP/IP is installed, go to step 6.
4: In the Network Component Type dialog box, select Protocol and click Add button.
5: In the Select Network Protocol dialog box, select Microsoft and TCP/IP and then click the
OK button to start installing the TCP/IP protocol. You may need your Windows CD to complete the installation.
6: After installing TCP/IP, go back to the Network dialog box. Select TCP/IP from the list of
Network Components and then click the Properties button.
7: Check each of the tabs and verify the following settings:
x Bindings: Check Client for Microsoft Networks and File and printer sharing for
Microsoft Networks.
x Gateway: All fields are blank. x DNS Configuration: Select Disable DNS. x WINS Configuration: Select Disable WINS Resolution.
x IP Address: Select Obtain IP address automatically.
8
8: Reboot the PC. Your PC will now obtain an IP address automatically from your Broadband Router’s DHCP server.
Note: Please make sure that the Broadband router’s DHCP server is the only DHCP server
available on your LAN.
Once you’ve configured your PC to obtain an IP address automatically, please proceed to Step 3
2b) Windows XP
1: Click the Start button and select Settings, then click Network Connections. The Network
Connections window will appear.
2: Double-click Local Area Connection icon. The Local Area Connection window will
appear.
3: Check your list of Network Components. You should see Internet Protocol [TCP/IP] on
your list. Select it and click the Properties button.
4: In the Internet Protocol (TCP/IP) Properties window, select Obtain an IP address
automatically and Obtain DNS server address automatically as shown on the following screen.
9
5: Click OK to confirm the setting. Your PC will now obtain an IP address automatically
from your Broadband Router’s DHCP server.
Note: Please make sure that the Broadband router’s DHCP server is the only DHCP server
available on your LAN.
Once you’ve configured your PC to obtain an IP address automatically, please proceed to Step 3.
2c) Windows 2000
1: Click the Start button and select Settings, then click Control Panel. The Control Panel window will appear.
2: Double-click Network and Dial-up Connections icon. In the Network and Dial-up
Connection window, double-click Local Area Connection icon. The Local Area Connection window will appear.
3: In the Local Area Connection window, click the Properties button.
4: Check your list of Network Components. You should see Internet Protocol [TCP/IP] on
your list. Select it and click the Properties button.
5: In the Internet Protocol (TCP/IP) Properties window, select Obtain an IP address
10
automatically and Obtain DNS server address automatically as shown on the following
screen.
6: Click OK to confirm the setting. Your PC will now obtain an IP address automatically
from your Broadband Router’s DHCP server.
Note: Please make sure that the Broadband router’s DHCP server is the only DHCP server
available on your LAN.
Once you’ve configured your PC to obtain an IP address automatically, please proceed to Step 3.
2d) Windows NT
1: Click the Start button and select Settings, then click Control Panel. The Control Panel window will appear.
2: Double-click Network icon. The Network window will appear. Select the Protocol tab from
the Network window.
3: Check if the TCP/IP Protocol is on your list of Network Protocols. If TCP/IP is not installed, click the Add button to install it now. If TCP/IP is installed, go to step 5.
4: In the Select Network Protocol window, select the TCP/IP Protocol and click the Ok
11
button to start installing the TCP/IP protocol. You may need your Windows CD to complete the installation.
5: After you install TCP/IP, go back to the Network window. Select TCP/IP from the list of
Network Protocols and then click the Properties button.
6: Check each of the tabs and verify the following settings:
x IP Address: Select Obtain an IP address from a DHCP server. x DNS: Let all fields are blank. x WINS: Let all fields are blank. x Routing: Let all fields are blank.
7: Click OK to confirm the setting. Your PC will now obtain an IP address automatically
from your Broadband Router’s DHCP server.
Note: Please make sure that the Broadband router’s DHCP server is the only DHCP server
available on your LAN.
Once you’ve configured your PC to obtain an IP address automatically, please proceed to Step 3.
12
3) Once you have configured your PCs to obtain an IP address automatically, the router’s DHCP server will automatically give your LAN clients an IP address. By default the Broadband Router’s DHCP server is enabled so that you can obtain an IP address automatically. To see if you have obtained an IP address, see Appendix A.
Note: Please make sure that the Broadband router’s DHCP server is the only DHCP server available on your LAN. If there is another DHCP on your network, then you’ll need to switch one of the DHCP servers off. (To disable the Broadband router’s DHCP server see chapter 2 LAN Port)
4) Once your PC has obtained an IP address from your router, enter the default IP address
192.168.1.1 (broadband router’s IP address) into your PC’s web browser and press <enter>
5) The login screen below will appear. Enter the “User Name” and “Password” and then click <OK> to login.
Note: By default the user name is “admin” and the password is “admin”. For security reasons it is recommended that you change the password as soon as possible (in General setup/system/password, see chapter 2)
6) The HOME page screen below will appear. The Home Page is divided into four sections,
Quick Setup Wizard, General Setup, Status Information and Tools.
Quick Setup Wizard (Chapter 1)
If you only want to start using the broadband router as an Internet Access device then you ONLY need to configure the screens in the Quick Setup Wizard section.
13
General Setup (Chapter 2)
If you want to use more advanced features that the broadband router has to offer, then you’ll need to configure the Quick Setup Wizard and the General Setup section. Alternatively, you can just configure the General Setup section, since the General Setup/WAN and the Quick Setup Wizard contain the same configurations.
Status Information (Chapter 3)
The Status Information section is for you to monitor the router’s current status information only.
Tools (Chapter 4)
If you want to Reset the router (because of problems) or save your configurations or upgrade the firmware then the Tools section is the place to do this.
Menu Description
Quick Setup Wizard (Chapter 1) Select your Internet connection type and then
input the configurations needed to connect to your Internet Service Provider (ISP).
General Setup (Chapter 2) This section contains configurations for the
Broadband router’s advance functions such as:
Address Mapping, Virtual Server, Access Control, Hacker Attack Prevention, DMZ, Special applications and other functions to meet your LAN requirements.
Status Information (Chapter 3) In this section you can see the Broadband
router's system information, Internet Connection,
14
Device Status, System Log, Security Log and DHCP client information.
Tools (Chapter 4)
This section contains the broadband router’s Tools - Tools include Configuration tools, Firmware upgrade and Reset. Configuration tools allow you to Backup (save), Restore, or Restore to Factory Default configuration for your Broadband router. The Firmware upgrade tool allows you to upgrade your Broadband router's firmware. The RESET tool allows you to reset your Broadband router.
Logout Selecting logout will return you to the LOGIN
page
7) Click on Quick Setup Wizard (see chapter 1) to start configuring settings required by your ISP so that you can start accessing the Internet. The other sections (General Setup, Status Information and Tools) do not need to be configured unless you wish to implement/monitor more advance features/information.
Select the section (Quick Setup Wizard, General Setup, Status Information and Tools) you wish to configure and proceed to the corresponding chapter. Use the selections on the web management’s top right hand page (see below) to navigate around the web-based management User Interface.
15
Chapter 1
Quick Setup
The Quick Setup section is designed to get you using the broadband router as quickly as possible. In the Quick Setup you are required to fill in only the information necessary to access the Internet. Once you click on the Quick Setup Wizard in the HOME page, you should see the screen below.
Step 1) Time Zone
The Time Zone allows your router to base its time on the settings configured here, this will affect functions such as Log entries and Firewall settings.
Parameter Description
Set Time Zone Select the time zone of the country you are currently in.
The router will set its time based on your selection.
Time Server Address You can manually assign time server address if the
default time server dose not work.
Enable Daylight Savings The router can also take Daylight savings into
account. If you wish to use this function, you must check/tick the enable box to enable your daylight saving configuration (below).
Start Daylight Savings Time Select the period in which you wish to start daylight
Savings Time
End Daylight Savings Time
Select the period in which you wish to end daylight Savings Time
16
Click on NEXT to proceed to the next page (step 2) Broadband Type.
Step 2) Broadband Type
In this section you have to select one of four types of connections that you will be using to connect your broadband router’s WAN port to your ISP (see screen below).
Note: Different ISP’s require different methods of connecting to the Internet, please check with your ISP as to the type of connection it requires.
Menu Description
1.1 Cable Modem
1.2 Fixed-IP xDSL
Your ISP will automatically give you an IP address
Your ISP has given you an IP address already
1.3 PPPoE Your ISP requires you to use a Point-to-Point Protocol over
Ethernet (PPPoE) connection.
1.4 PPTP Your ISP requires you to use a Point-to-Point Tunneling Protocol
(PPTP) connection.
1.5 L2TP Your ISP requires you to use a Layer Two Tunneling Protocol
(L2TP) connection.
17
1.6 Telstra Big Pond This Protocol only used for Australia’s ISP connection.
Click on one of the WAN type and then proceed to the manual’s relevant sub-section (1.1, 1.2,
1.3, 1.4, 1.5 or 1.6). Click on Back to return to the previous screen.
1.1 Cable Modem
Choose Cable Modem if your ISP will automatically give you an IP address. Some ISP’s may also require that you fill in additional information such as Host Name and MAC address (see screen below).
Note: The Host Name and MAC address section is optional and you can skip this section if your ISP does not require these settings for you to connect to the Internet.
Parameters Description Host Name If your ISP requires a Host Name, type in the host name
provided by your ISP, otherwise leave it blank if your ISP does not require a Host Name.
MAC Address
Your ISP may require a particular MAC address in order for you to connect to the Internet. This MAC address is the PC’s MAC address that your ISP had originally connected your Internet connection to. Type in this MAC address in this section or use the “Clone MAC Address” button to replace the WAN MAC address with the MAC address of that PC (you have to be using that PC for the Clone MAC Address button to work). To find out the PC’s MAC address see Appendix A. (see Glossary for an explanation on MAC address)
18
Click <OK> when you have finished the configuration above. Congratulations! You have completed the configuration for the Cable Modem connection. You can start using the router now, if you wish to use some of the advance features supported by this router see chapter 2, 3, 4.
1.2 Fixed-IP xDSL
Select Fixed-IP xDSL if your ISP has given you a specific IP address for you to use. Your ISP should provide all the information required in this section.
Parameters Description
IP This is the IP address that your ISP has given you.
Gateway IP
DNS
Subnet Mask
Click <OK> when you have finished the configuration above. Congratulations! You have completed the configuration for the Fixed-IP x DSL connection. You can start using the router now, if you wish to use some of the advance features supported by this router see chapter 2, 3, 4.
This is the ISP’s IP address gateway
This is the ISP’s DNS server IP address
Enter the Subnet Mask provided by your ISP (e.g. 255.255.255.0)
19
1.3 PPPoE
Select PPPoE if your ISP requires the PPPoE protocol to connect you to the Internet. Your ISP should provide all the information required in this section.
Parameter Description
User Name
Password
Service Name This is optional.
Enter the User Name provided by your ISP for the PPPoE connection
Enter the Password provided by your ISP for the PPPoE connection
Enter the Service name should your ISP
requires it, otherwise leave it blank.
MTU This is optional. You can specify the maximum size of your
transmission packet to the Internet. Leave it as it is if you to not wish to set a maximum packet size.
Connection Type If you select “Continuous”, the router will always connect
to the ISP. If the WAN line breaks down and links again, the router will auto-reconnect to the ISP. If you select “Connect On Demand”, the router will auto­connect to the ISP when someone want to use the Internet and keep connected until the WAN idle timeout. The router will close the WAN connection if the time period that no one is using the Internet exceeds the “Idle Time”.
20
If you select “Manual”, the router will connect to ISP only when you click “Connect” manually from the Web user interface. The WAN connection will not disconnected due to the idle timeout. If the WAN line breaks down and latter links again, the router will not auto-connect to the ISP.
Idle Time
Click <OK> when you have finished the configuration above. Congratulations! You have completed the configuration for the PPPoE connection. You can start using the router now, if you wish to use some of the advance features supported by this router see chapter 2, 3, 4.
You can specify an idle time threshold (minutes) for the WAN port. This means if no packets have been sent (no one using the Internet) during this specified period, the router will automatically disconnect the connection with your ISP. Note: This “idle timeout” function may not work due to abnormal activities of some network application software, computer virus or hacker attacks from the Internet. For example, some software sends network packets to the Internet in the background, even when you are not using the Internet. So please turn off your computer when you are not using it. This function also may not work with some ISP. So please make sure this function can work properly when you use this function in the first time, especially your ISP charge you by time used.
21
1.4 PPTP
Select PPTP if your ISP requires the PPTP protocol to connect you to the Internet. Your ISP should provide all the information required in this section.
Parameter Description
Obtain an IP address The ISP requires you to obtain an IP address by DHCP automatically before connecting to the PPTP server.
Use the following IP address The ISP give you a static IP to be used to connect to the PPTP server.
IP Address This is the IP address that your ISP has given you to
establish a PPTP connection.
Subnet Mask
Gateway
User ID
Enter the Subnet Mask provided by your ISP (e.g. 255.255.255.0)
Enter the IP address of the ISP Gateway
Enter the User Name provided by your ISP for the PPTP connection. Sometimes called a Connection ID
22
Password
Enter the Password provided by your ISP for the PPTP connection
PPTP Gateway If your LAN has a PPTP gateway, then enter that PPTP gateway
IP address here. If you do not have a PPTP gateway then enter the ISP’s Gateway IP address above
Connection ID This is the ID given by ISP. This is optional.
BEZEQ-ISRAEL Select this item if you are using the service provided by
BEZEQ in Israel.
Connection Type If you select “Continuous”, the router will always connect
to the ISP. If the WAN line breaks down and links again, the router will auto-reconnect to the ISP. If you select “Connect On Demand”, the router will auto­connect to the ISP when someone want to use the Internet and keep connected until the WAN idle timeout. The router will close the WAN connection if the time period that no one is using the Internet exceeds the “Idle Time”. If you select “Manual”, the router will connect to ISP only when you click “Connect” manually from the Web user interface. The WAN connection will not disconnected due to the idle timeout. If the WAN line breaks down and latter links again, the router will not auto-connect to the ISP.
Idle Time You can
port. This means if no packets have been sent (no one using the Internet) throughout this specified period, then the router will automatically disconnect the connection with your ISP. Note: This “idle timeout” function may not work due to abnormal activities of some network application software, computer virus or hacker attacks from the Internet. For example, some software sends network packets to the Internet in the background, even when you are not using the Internet. So please turn off your computer when you are not using it. This function also may not work with some ISP. So please make sure this function can work properly when you use this function in the first time, especially your ISP charge you by time used.
Click <OK> when you have finished the configuration above. Congratulations! You have completed the configuration for the PPTP connection. You can start using the router now, if you wish to use some of the advance features supported by this router see chapter 2, 3, 4.
specify an idle time threshold (minutes) for the WAN
23
1.5 L2TP
Select L2TP if your ISP requires the L2TP protocol to connect you to the Internet. Your ISP should provide all the information required in this section.
Parameter Description
Obtain an IP address The ISP requires you to obtain an IP address by DHCP automatically before connecting to the L2TP server.
MAC Address Your ISP may require a particular MAC address in order
for you to connect to the Internet. This MAC address is the PC's MAC address that your ISP had originally connected your Internet connection to. Type in this MAC address in this section or use the "Clone MAC Address" button to replace the WAN MAC address with the MAC address of that PC (you have to be using that PC for the Clone MAC Address button to work). To find out the PC's MAC address see Appendix A. (see Glossary for an explanation on MAC address)
Use the following IP address The ISP gives you a static IP to be used to connect to the L2TPserver.
24
IP Address This is the IP address that your ISP has given you to
establish a L2TP connection.
Subnet Mask Enter the Subnet Mask provided by your ISP
(e.g. 255.255.255.0)
Gateway Enter the IP address of the ISP Gateway
User ID
Password
Enter the User Name provided by your ISP for the PPTP connection. Sometimes called a Connection ID
Enter the Password provided by your ISP for the PPTP connection
L2TP Gateway If your LAN has a L2TP gateway, then enter that L2TP gateway
IP address here. If you do not have a L2TP gateway then enter the ISP’s Gateway IP address above
MTU This is optional. You can specify the maximum size of your
transmission packet to the Internet. Leave it as it is if you to not wish to set a maximum packet size.
Connection Type If you select “Continuous”, the router will always connect
to the ISP. If the WAN line breaks down and links again, the router will auto-reconnect to the ISP. If you select “Connect On Demand”, the router will auto­connect to the ISP when someone want to use the Internet and keep connected until the WAN idle timeout. The router will close the WAN connection if the time period that no one is using the Internet exceeds the “Idle Time”. If you select “Manual”, the router will connect to ISP only when you click “Connect” manually from the Web user interface. The WAN connection will not be disconnected due to the idle timeout. If the WAN line breaks down and latter links again, the router will not auto-connect to the ISP.
Idle Time Out
The WAN "idle timeout" auto-disconnect function may not work due to abnormal activities of some network application software, computer virus or hacker attacks from the Internet. For example, some software sends network packets to the Internet in the background, even when you are not using the Internet. This function also may not work with some ISP. So please make sure this function can work properly when you use this function in the first time, especially your ISP charge you by time used. Due to the many uncontrollable issues, we do not guarantee the WAN "idle timeout" auto-disconnect function will always work. In order to prevent from extra fee charged by ISP, please TURN OFF THE ROUTER WHEN YOU FINISHED USING THE INTERNET.
25
Click <OK> when you have finished the configuration above. Congratulations! You have completed the configuration for the L2TP connection. You can start using the router now, if you wish to use some of the advance features supported by this router see chapter 2, 3, 4.
26
1.6 Telstra Big Pond
Select Telstra Big Pond if your ISP requires the Telstra Big Pond protocol to connect you to the Internet. Your ISP should provide all the information required in this section. Telstra Big Pond protocol is used by the ISP in Australia.
Parameter Description
User Name
Enter the User Name provided by your ISP for the Telstra Big Pond connection
Password Enter the Password provided by your ISP for the Telstra Big
Pond connection
User deside login server Select if you want to assign the IP of Telstra Big Pond’s login manually server manually.
Login Server The IP of the Login Server.
Click <OK> when you have finished the configuration above. Congratulations! You have completed the configuration for the Telstra Big Pond connection. You can start using the router now, if you wish to use some of the advance features supported by this router see chapter 2, 3, 4.
27
Chapter 2
General Settings
Once you click on the General Setup button at the Home Page, you should see the screen below.
If you have already configured the Quick Setup Wizard you do NOT need to configure anything thing in the General Setup screen for you to start using the Internet.
The General Setup contains advanced features that allow you to configure the router to meet your network’s needs such as: Wireless, Address Mapping, Virtual Server, Access Control,
Hacker Attack Prevention, Special Applications, DMZ and other functions.
Below is a general description of what advance functions are available for this broadband router.
Menu Description
2.1 System
2.2 WAN
2.3 LAN
This section allows you to set the Broadband router’s system Time Zone, Password and Remote Management Administrator.
This section allows you to select the connection method in order to establish a connection with your ISP (same as the Quick Setup Wizard section)
You can specify the LAN segment’s IP address, subnet Mask, enable/disable DHCP and select an IP range for your LAN
28
2.4 Wireless You can setup the wireless LAN’s SSID, WEP key, MAC
filtering.
2.5 QoS You can setup the QoS bandwidth control policy.
2.6 NAT
2.7 Firewall
Select one of the above five General Setup selections and proceed to the manual’s relevant sub­section
You can configure the Address Mapping, Virtual Server and Special Applications functions in this section. This allows you to specify what user/packet can pass your router’s NAT.
The Firewall section allows you to configure Access Control, Hacker Prevention and DMZ.
29
2.1 System
The system screen allows you to specify a time zone, to change the system password and to specify a remote management user for the broadband router.
Parameters Description
System Settings
2.1.1 Time Zone Select the time zone of the country you are currently in.
The router will set its time based on your selection.
2.1.2 Password Settings
Allows you to select a password in order to access the web-based management website.
2.1.3 Remote Management You can specify a Host IP address that can perform
remote management functions.
Select one of the above three system settings selections and proceed to the manual’s relevant sub-section
30
Loading...
+ 68 hidden pages
Buy Points How it Works FAQ Contact Us Questions and Suggestions Privacy Policy Cookie Policy Terms of Use