TomTom LINK 105 Installation Manual

TomTom LINK 105

Installation Guide

2

Contents

Read me first 3

Read the Addendum and Safety notices........................................................................................... 3

Welcome ............................................................................................................................................. 3

Safety first 4

Important safety notices and warnings ............................................................................................. 4

Before the installation 5

Notice for maintenance work ............................................................................................................. 5

Components ....................................................................................................................................... 5

Requirements ..................................................................................................................................... 5

Installing your LINK 105 7

Configuring a Bluetooth connection with WEBFLEET ...................................................................... 7

Configuring a Bluetooth connection with the Activation Tool ......................................................... 9

Installing LINK 105 in your vehicle .................................................................................................. 10

Diagnostics 12

Understanding your LINK 105.......................................................................................................... 12

Resetting your LINK 105 ................................................................................................................... 12

Technical data ................................................................................................................................... 13

Addendum 14

TomTom Telematics Limited Warranty 20

3

Before operating this product please read the Installation Guide.

Read the Addendum and Safety notices

IMPORTANT - BEFORE INSTALLING AND USING YOUR TomTom LINK 105 READ THE

ADDENDUM AND THE INSTRUCTIONS CONTAINED THEREIN! ALSO READ THE IMPORTANT
SAFETY NOTICES AND WARNINGS INCLUDED IN THIS DOCUMENT! READ THE INSTRUCTIONS
IN THIS DOCUMENT THOROUGHLY!

Welcome

With the TomTom LINK 105TM you can retrieve fuel consumption data over the OBD-II connector in
your vehicle and see this in WEBFLEET in real time. TomTom LINK 105 works together with the
TomTom LINK 5xx/4xx via Bluetooth and therefore requires minimal installation effort. This
document shows how to set up your LINK 105.

Read me first

4

Important safety notices and warnings

Important: Read the following safety instructions carefully. Read the instructions in this document

carefully.

TomTom Telematics accept no liability for damage that results from disregarding the safety
instructions. This document is part of the product. Keep it in a safe place. If you pass the unit on to
a new user, make sure you give them this document as well.

Danger of explosion

Parts of the TomTom LINK 105 can cause sparks that can lead to explosions. This may endanger
human health and life. Do not use the unit in areas with high risk of explosion. When using a
TomTom LINK 105 in a vehicle fuelled by liquefied gas, follow the safety regulations of the country
in which the vehicle is operated.

Damage caused through improper installation

The installation and initial operation of the unit must be performed by authorised personnel only
for example, a qualified radio dealer or an automotive electronics workshop.

Risk of injury in case of accidents

Do not mount the unit or accessories in the inflation area of airbags or in the impact area for the
head or knees. Choose an installation location that will avoid interference with displays, safety
equipment and controls.

Damage to the chassis

Make sure you do not drill into parts of the chassis that have structural or security-related
functions. This is because you cannot be certain that they will function properly after modification.

Risk of fire

Make sure you do not drill into covered wiring harnesses, fuel lines or similar components. Drilling
into these can cause fire.

Repair and replacement

Repairs must be carried out by authorised and qualified personnel only. Never replace damaged
parts of the unit yourself. Send the defective unit to TomTom Telematics for repair. Only the
qualified staff of TomTom Telematics are authorised to repair or replace parts.

Damage to the device

Short-circuits inside the unit can be caused by contact with water or other liquids. The unit may be
damaged by contact with water. Use and store the unit in an area protected from water.

Safety first

5

Notice for maintenance work

If you need the OBD-II connector in your vehicle, for example for maintenance, remove your LINK
105 from the connector and reconnect it afterwards.

Important: To remove the LINK 105 from the OBD-II connector, pull on the handle of the LINK 105
and not the device itself as this may cause damage.

Components

The following figure shows the different parts of the LINK 105.

1. Handle

2. Reset button

3. Bluetooth LED (Blue)

4. Power LED (Green)

5. Body

6. Bluetooth address

7. OBD-II plug

Requirements

Before installing your LINK 105 make sure you fulfil the following requirements:

 Your vehicle is fitted with a LINK 5xx/4xx with the firmware version 5.0 or higher.
 The LINK 5xx/4xx must be activated in WEBFLEET.
 Your vehicle has an OBD-II connector. If the OBD-II connector of your vehicle does not provide

enough space to insert the LINK 105, you can use the OBD-II extension cable from TomTom
Telematics.

 To use the Activation Tool for your LINK 5xx/4xx, you need a laptop with the Activation Tool

installed, the Mini USB cable and the activation code, which you can find in your WEBFLEET
contract confirmation.

Before the installation

6

Download the latest version of the Activation Tool from the Partner Portal. Go to telemat-

ics.tomtom.com/support and select Activation and Diagnostics.

7

There are two steps to setting up your LINK 105:

1. Configure a Bluetooth connection between your LINK 105 and your LINK 5xx/4xx.

There are two ways to establish a Bluetooth connection between your LINK 105 and your LINK
5xx/4xx:

 By configuring a Bluetooth connection with WEBFLEET
 By configuring a Bluetooth connection with the Activation Tool

Make sure you have properly noted and entered the Bluetooth address of your LINK 105,
which you can find on the label on the OBD-II plug.

2. Install your LINK 105 in your vehicle.

Important: If the LINK 105 has been used in another vehicle before, you need to reset the device
before you start the engine of your vehicle, otherwise the calculation of the fuel consumption may
be incorrect.

Configuring a Bluetooth connection with WEBFLEET

This section describes how to pair your LINK 105 with the LINK 5xx/4xx installed in your vehicle
using WEBFLEET. You can also configure a Bluetooth connection using the Activation Tool
instead.

Note: Make sure your vehicle is properly fitted with a LINK 5xx/4xx according to the require-

ments for the installation.

1. Log in to WEBFLEET here telematics.tomtom.com/login.

2. Click Vehicles.

3. Select your vehicle from the list.

4. In the details panel on the right, click Contract/Device.

Installing your LINK 105