Toastmaster PRO-OE3B3 User Manual

TRANSMITTER PROGRAMMING GUIDE

Model : PRO-OE3B3

The transmitters included with the security system have been pre-programmed
at the factory, with each button pre-assigned to control a specific function of the
security system. Although the security system in the vehicle has either a 3 or 4
channel receiver, depending on the model, the transmitters included with the
system are capable of transmitting 7 distinct signals. This allows you to program
each transmitter to more than one vehicle in two car families and also allows you
to change which button(s) control certain functions of the system.
(Example: Transmitter channel 5 can be programmed to activate Receiver
channel 2.) Refer to the chart below for access to each of the transmitter channels,
and for the standard factory button assignments.

TRANSMITTER SYSTEM RECEIVER

CHANNEL BUTTON CHANNEL FUNCTION

1 1 Remote Emergency Panic

2 2 Remote Emergency Panic

33

4& 4

Remote Arm
Remote Door Lock

Remote Disarm

Remote Door Unlock/Unlock 2

Single Push Pulsed Output for Optional Accessory
Or Double Push For Additional Optional Accessory

Single Push Pulsed Output for Optional Accessory
Or Push And Hold For Extended Output

5& 5

6 & 6 RF Channel For Options

7 7 RF Channel For Options

Some of the more common accessories for these additional channels are;

All 3

Buttons

AS 9554 Remote Garage Door Interface
AS 9075 Remote car starter
AS 9153 Remote window roll up
AS 9256 Remote trunk release relay

Released 7-17-01.

Single Push Pulsed Output for Optional Accessory
Or Push And Hold For Extended Output

128-6121

1 of 4

PROGRAMMING THE TRANSMITTERS

It is important to remember that during programming, each individual step of
the procedure must be executed within 15 seconds of the previous step.

When the 15 second time limit is allowed to expire, the system will automatically
terminate the programming mode. This is indicated by a long chirp from the
siren.

NOTE: Some keyless entry systems will flash the interior light to indicate a

stored code. Substitute the words light flash below where indicated
sounding device will beep.

Additionally, the system will store codes from up to four different transmitters.
If a 5th transmitter is programmed to any receiver channel, then the first
transmitter programmed to that channel will be erased from the system's
memory.

To Program replacement or additional transmitters:

1. Enter the vehicle, and turn the ignition key to the "on" position.

2. Press and release the valet push-button switch 3 times.

3. The dash LED will flash one time and the sounding device will beep one
time, indicating the system is ready to accept programming for receiver's
Lock channel 1.

4. Press and hold the Lock transmitter button until the sounding device emits
a long beep, indicating the signal has been stored into memory.

5. If you have additional transmitters (up to 4) that need to be programmed,
repeat step 4 for each transmitter.

6. Press and release the valet push-button switch once.

7. The dash LED will flash two times and the sounding device will beep two
times, indicating the system is ready to accept programming for receiver's
Unlock channel 2.

8. Press and hold the Unlock transmitter button until the sounding device
emits a long beep, indicating the signal has been stored into memory.

9. If you have additional transmitters (up to 4) that need to be programmed,
repeat step 8 for each transmitter.

10. Press and release the valet push-button switch once.

11. The dash LED will flash three times and the sounding device will beep
three times, indicating the system is ready to accept programming for
receiver's channel 3.

12. Press and hold the selected Option transmitter button until the sounding
device emits a long beep, indicating the signal has been stored into
memory.

13. If you have additional transmitters (up to 4) that need to be programmed,
repeat step 12 for each transmitter.

128-6121

2 of 4