Page 1
Home » THOMSON » THOMSON WHP3001BK Wireless UHF Headphones Instruction Manual
THOMSON WHP3001BK Wireless UHF Headphones Instruction Manual
Thank you for choosing a Thomson product.
Take your time and read the following instructions and information completely.
Please keep these instructions in a safe place for future reference. If you sell the device, please pass these
operating instructions on to the new owner.
THOMSON WHP3001BK Wireless UHF Headphones
Instruction Manual
Manuals+ — User Manuals Simplified.
Page 2
Contents
1 Explanation of Warning Symbols and
Notes
2 Controls and displays, Fig. 1+3
3 Package contents
4 Safety Notes
5 Technical specifications
6 Installing the transmitter/charging station,
7 Installing the receiver/headphones, Fig. 2
8 Getting started
9 Charging, Fig. 3
10 Troubleshooting
11 Care and Maintenance
12 Warranty Disclaimer
13 Service and Support
14 Documents / Resources
15 Related Posts
Explanation of Warning Symbols and Notes
Risk of electric shock
This symbol indicates product parts energized with a dangerous voltage of sufficient magnitude to constitute a risk
of electric shock.
Warning
This symbol is used to indicate safety instructions or to draw your attention to specific hazards and risks.
Note
This symbol is used to indicate additional information or important notes.
Controls and displays, Fig. 1+3
Page 3
Page 4
1. Charge status LED indicator (green)
2. Power/signal LED indicator (red)
3. Power button
4. Volume control
5. Auto-Tune button
6. Frequency channel switch
7. Power LED indicator (green)
Package contents
1 WHP3001BK UHF wireless headphones
1 transmitter with charging station
2 NiMH AAA batteries
1 power supply unit
1 audio adapter cable, RCA stereo to 3.5 mm jack
1 jack adapter 6.3 mm/3.5 mm
Page 5
Safety Notes
The product is intended for private, non-commercial use only.
Use the product for its intended purpose only.
Children should be supervised to ensure that they do not play with the device.
Do not use the product in areas where the use of electronic devices is not permitted.
Lay all cables so that they do not pose a tripping hazard.
Do not bend or crush the cable.
Do not drop the product and do not expose it to any major shocks.
Dispose of packaging material immediately according to locally applicable regulations.
Do not modify the product in any way. Doing so voids the warranty.
The batteries and charging station included in the delivery go together and should always be used in
combination.
The product is intended for indoor use only.
Protect the product from dirt, moisture and overheating, and only use it in a dry environment.
Use the item only in moderate climatic conditions.
Keep this product, as all electrical products, out of the reach of children!
Do not operate the product outside the power limits given in the specifications.
Do not use the product in moist environments and avoid splashes.
Do not place any objects on the device and never use it to keep things on.
Risk of electric shock
Do not open the device or continue to operate it if it becomes damaged.
Do not use the product if the AC adapter, the adapter cable or the mains cable are damaged.
Do not attempt to service or repair the product yourself. Leave any and all service work to qualified experts.
Warning – Batteries
When inserting batteries, note the correct polarity (+ and – markings) and insert the batteries accordingly.
Failure to do so could result in the batteries leaking or exploding.
Only use batteries (or rechargeable batteries) that match the specified type.
Before you insert the batteries, clean the battery contacts and the polar contacts.
Do not allow children to change batteries without supervision.
Do not mix old and new batteries or batteries of a different type or make.
Remove the batteries from products that are not being used for an extended period (unless these are being
kept ready for an emergency).
Do not short-circuit batteries.
Do not charge batteries.
Do not throw batteries in a fire.
Keep batteries out of the reach of children.
Never open, damage or swallow batteries or allow them to enter the environment. They can contain toxic,
Page 6
environmentally harmful heavy metals.
Immediately remove and dispose of dead batteries from the product.
Avoid storing, charging or using the device in extreme temperatures and extremely low atmospheric pressure
(for example, at high altitudes).
Warning – High volumes
High sound pressure level!
There isarisk of hearing damage.
To prevent hearing loss, avoid listening at high volume levels for long periods.
Always keep the volume at a reasonable level. Loud volumes, even over short periods, can cause hearing loss.
Using this product limits your perception of ambient noise. For this reason, do not operate any
vehicles or machines while using this product.
Technical specifications
Transmitting mode UHF stereo
Frequency band(s) 863.53 – 864.53 MHz
Maximum radio-frequency power transmitte
d
<5dBm
Operating voltage Transmitter: 8 V, 70 mA Receiver: 2.4 V, (2 x 1.2 V NiMH AAA)
Frequency range 20 Hz – 20 KHz
Distortion < 2%
Signal-to-noise ratio > 54 dB
Range 100 m max. (outdoors) 20–30 m (indoors)
Operating time 8 hrs (at medium volume)
Specifications in accordance with Regulation (EU) 2019/1782
Page 7
Manufacturer’s name or trade mark, comme
rcial registration number and address
Thomson, HRA12159, Dresdner Str. 9, 86653 Monheim
Model identifier YLS0056A-E080040
Input voltage 100-240 V
Input AC frequency 50/60 Hz
Output voltage / Output current/ Output pow
er
8.0 V DC / 0.4 A / 3.2 W
Average active efficiency 76.8 %
Efficiency at low load (10 %) 65.1 %
No-load power consumption 0.04 W
Installing the transmitter/charging station,
Fig. 3
Warning
Only operate the product from a socket that has been approved for the device. The socket must be installed
close to the product and must be easily accessible.
Disconnect the product from the power supply using the On/Off switch – if this is not available, unplug the
power cord from the socket.
If using a multi-socket power strip, make sure that the total power consumption of all connected devices does
not exceed the power strip’s maximum throughput rating.
If you will not be using the product for a prolonged period, disconnect it from mains power.
Connect the power supply to the power socket on the rear side of the transmitter.
Connect the power supply to a mains socket.
Connect the RCA plugs of the audio adapter cable to the RCA sockets on the rear side of the transmitter.
Connect the other end (jack plug) to the headphone jack of your audio source (television, hi-fi system, DVD
player, MP3 player, etc.).
The red LED (2) lights up.
Installing the receiver/headphones, Fig. 2
Carefully pull off the earpad on the right-hand side.
Insert the two batteries supplied, making sure you observe correct polarity.
Reinsert the earpad until it audibly clicks into place.
Getting started
Switch on the audio source connected to the transmitter (TV or audio player).
Switch on the headphones by pressing the Power button (3). The LED (7) of the headphones lights up green.
Page 8
Make sure that the red LED (2) is lit. This confirms that the rechargeable batteries are charged.
Put the headphones on and set the volume to the desired level.
Before using the headphones for the first time, make sure that the battery is fully charged. Charge the battery
for at least 24 hours before the first use.
Switch off the headphones if they are not being used and put them back onto the transmitter’s charging
contacts.
Note
If you cannot get an optimum signal frequency, press the Auto Tune button (5) on the headphones.
If you cannot get an adequate frequency, change the frequency channel on the rear side of the transmitter.
Then confirm the corresponding channel on the headphones by pressing the Auto-Tune button.
To get the best sound experience with your headphones, you should set the volume of the sound source (TV,
stereo system, etc.) as high as possible and reduce the volume on the headphones themselves.
The transmitter will automatically switch off if it receives no audio signal for approximately 2 minutes, or if the
signal from the audio source is too weak for flawless reception. As soon as the signal strength is sufficient, the
transmitter will automatically switch back on. The headphones do not switch off automatically
Charging, Fig. 3
Switch off the headphones.
Place the headphones in the charging station as shown, and make sure that the charging contacts of both
devices properly touch each other.
The green LED (1) lights up. Charging begins automatically
Note
To prevent damage to the batteries, always switch off the headphones when they are not in use.
Before using the product for the first time, the batteries should be fully charged. To guarantee an acceptable
charge, the batteries should initially be charged for 24 hours. Subsequent charging cycles then last
approximately 10 hours.
The batteries will not be charged if the transmitter is off.
Troubleshooting
No sound
Check that the power supply plug is fully inserted into the mains socket and the other end is properly
connected to the power supply socket on the transmitter.
Make sure that the headphones are on.
The battery in the headphones may have insufficient remaining charge. Charge the battery.
Check that your TV, hi-fi system or audio source is switched on and a channel is correctly configured to send
Page 9
an audio signal.
Increase the volume using the control on the headphones.
The connected audio/video device may not be in playback mode. Please start the playback.
The output volume of the audio source may be too low. Adjust the volume accordingly.
Distortion
Press the Auto-Tune button.
Set a different frequency channel (1, 2 or 3). Then press the Auto-Tune button again.
The battery in the headphones may have insufficient remaining charge. Charge the battery.
Increase the volume using the control on the headphones.
The distance between the headphones and the transmitter may be too great. Move the two devices closer
together and turn the headphones in the direction of the transmitter.
The input level of the audio signal may be too low. Increase the volume of the audio source.
Care and Maintenance
Note
Disconnect the device from the power supply before cleaning it or if it is not going to be used for a long period of
time.
Only clean this product with a slightly damp, lint-free cloth and do not use aggressive cleaning agents.
Warranty Disclaimer
Hama GmbH & Co KG assumes no liability and provides no warranty for damage resulting from improper
installation/mounting, improper use of the product or from failure to observe the operating instructions and/or
safety notes.
Service and Support
Please contact Hama Product Consulting if you have any questions about this product. Hotline: +49 9091 502-0
(German/English) Further support information can be found here: www.hama.com
Recycling Information
Note on environmental protection
After the implementation of the European Directive 2012/19/EU and 2006/66/EU in the national legal
system, the following applies: Electric and electronic devices as well as batteries must not be disposed of with
household waste. Consumers are obliged by law to return electrical and electronic devices as well as batteries at
the end of their service lives to the public collecting points set up for this purpose or point of sale. Details to this
are defined by the national law of the respective country. This symbol on the product, the instruction manual or the
package indicates that a product is subject to these regulations. By recycling, reusing the materials or other forms
of utilising old devices/ Batteries, you are making an important contribution to protecting our environment.
Page 10
Declaration of Conformity
Hereby, Hama GmbH & Co KG declares that the radio equipment type [00131957] is in compliance with
Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following internet
address: www.hama.com->00131957-Downloads
Documents / Resources
THOMSON WHP3001BK Wireless UHF Headphones [pdf] Instruction Manual
WHP3001BK, Wireless UHF Headphones
Manuals+,
Loading...