Thetford Spinflo 960, Spinflo 930, Spinflo 162, Spinflo 160, Spinflo 921 User And Installation Instructions Manual
...
BUILD-IN COOKING HOB
–
FOR USE WITH PROPANE GAS
SERIES 160 SERIES 167 SERIES 162 SERIES 960
SERIES 920 SERIES 930 SERIES 921 SERIES 910
USER AND INSTALLATION INSTRUCTIONS
READ AND RETAIN FOR FUTURE REFERENCE
FOR USE IN USA & CANADA
Issue 8
PCC 1272Y
THETFORD CONSUMER HOT LINE 1-800-543-1219
SPINFLO LIMITED, 19 Oakham Drive, Parkwood Industrial Estate
Rutland Road, Sheffield S3 9QY, ENGLAND.
TEL: + 44 (0) 114 273 8157 FAX: + 44 (0) 114 275 3094
j
If the information in this manual is not
followed exactly, a fire or explosion may
result causing property damage, personal
WARNING:
ury or death.
in
- Do not store or use gasoline or other
flammable vapors and liquids in the vicinity of
this or any other appliance.
- WHAT TO DO IF YOU SMELL GAS
• Do not try to light any appliance
• Do not touch any electrical switch
• Do not use any phone in your recreational
vehicle
• Clear the recreational vehicle of all occupants.
• Turn off the gas supply tank valve(s) or main
gas supply.
• Immediately call your gas supplier for
instructions.
• If you cannot reach your gas supplier, call the
fire department.
- Have the gas system checked and leakage
source corrected by a qualified installer,
service agency, manufacturer or dealer or the
gas supplier.
2
3
4
5
CONTROL POSITIONS – ALL MODELS
For either inset or worktop mounted appliances the minimum allowable
horizontal distance to combustible materials is as shown below.
APPLIANCE LOCATION
Note:
30 inches is the
minimum vertical distance
to combustible material above
the cooktop. This distance may be reduced
by using non-combustible construction in
accordance with table 5.6.6.5 Vertical Clearances
to Combustible Material or Metal Cabinets in
ANSI 119.2 2005.
6
WORKTOP CUTOUT DETAILS
( All dimensions in inches )
7
WORKTOP CUTOUT DETAILS
( All dimensions in inches )
8
WORKTOP CUTOUT DETAILS
( All dimensions in inches )
SERIES 162 & 167 – WORKTOP CUTOUT FOR SURFACE MOUNT SEAL
9
10
INTRODUCTION
In your own interest of safety, gas appliances should be installed by competent persons. Failure
to install the appliance correctly could invalidate any warranty or liability claims. This appliance
shall be installed in accordance with the manufacturers installation instructions, local and state
codes or, in the absence of such codes, with the Standard for Recreational Vehicles, ANSI
A119.2.
Data label
The data label is located on the underside of the hob. Ensure that the gas supply is Propane.
This appliance is designed for use with Propane gas and should not be converted for use with
any other gas.
Provision of Ventilation
The use of a gas cooking appliance results in the production of heat and moisture in a room in
which it is installed. Ensure that the kitchen is well ventilated and in accordance with local and
state codes. Do not obstruct the flow of combustion or ventilation air. In general, the appliance
should have adequate ventilation for complete combustion of gas, proper flueing and to
maintain temperature of immediate surroundings within safe limits.
Location
This appliance maybe installed in a kitchen/kitchen diner but NOT in a room containing a bath
or a shower. LP gas appliances must not be fitted below ground level. e.g. in a basement.
Choose a location free of drafts, open doors and clear of combustible materials and other fire
hazards. The location should ensure convenience of operation and service. Any adjoining wall
surface situated within 4
1
/2 in from cooker side (see page 6) must be made from a suitable non-
combustible material for a height of 6 in for the entire length of the hotplate.
Gas Category – All Models
PROPANE gas only 11 in wc ( 27.4mbar )
IMPORTANT
• THIS APPLIANCE IS SUITABLE FOR USE WITH PROPANE AND
SHOULD NOT BE USED ON ANY OTHER GAS.
• USE ONLY THE GAS PRESSURES SPECIFIED ABOVE
• IF NOT INSTALLED TO INSTRUCTIONS DETAILED HEREIN, WE THE
MANUFACTURER CAN NOT BE HELD RESPONSIBLE FOR ANY
PROBLEMS THAT OCCUR, OR POOR PERFORMANCE EITHER
PERCEIVED OR WITNESSED.
11
Loading...