Thetford ELECTRA MAGIC Owner's Manual

13

Because We Take Your Leisure Seriously

ELECTRA MAGIC

®

Owner’s Manual

RV and Marine

Recirculating Toilets

2

Operating Instructions

1. Initial Flush Charge

A. Fill until water reaches slightly above

the charge level (blue line) on indica­tor dial.

B. Add Thetford Aqua-Kem

®

Liquid
Holding Tank Deodorant as per
instructions on package.

2. To Flush

Depress ush button. (Note: Do not

depress button when unit is empty.)

To Empty RV Model

The Electra Magic is tted with a ter­mination valve on the bottom of the
unit. Depending on the installation, follow one of these

procedures:

A. Without holding tank – attach discharge hose to outlet

and open termination valve.

B. With holding tank – open termination valve. This dumps

contents of unit into the holding tank.

To Evacuate Marine Model

See your boat owner’s manual.

Congratulations!

…on your purchase of Thetford’s Electra Magic recirculat

ing

toilet, the most popular recirculating toilet in the world.

This unit is a 100% self-contained sanitation system which
requires no pressure water connection or holding tank
installation (an optional holding tank may be installed to
increase total capacity). The Electra Magic is operated by
a simple D.C. hookup, available in a 12-Volt or a 24-Volt
model, and may be discharged directly into the sewer or
into an optional holding tank.

Unique Filtration

Thetford’s unique ltration system puts an end to unpleasant
clogging. The exclusive lter cone assures that only ltered
uid is delivered to the recirculating pump.

Any Questions…

about your toilet or this Owner’s Manual?

Simply call Thetford’s

Customer Relations Department at

1-800-521-3032

1-800-543-1219

3

RV Installation Instructions continue on Page 5.

Installation

RV Model

1. Install the two closet bolts in closet ange.

2. While holding bolt up so the head touches underside

of closet ange, install one nut on each bolt and screw

nuts down until they
touch top of gauge. If
gauge is misplaced,
bottom surface of

nuts should be 1.34
in. (3.4 cm) above

oor.

5. Place unit on closet ange and locate position for plastic

locator disc by tracing around one of the front legs. Drill

5/32” dia. hole in oor and fasten disc to oor with at

sides oriented as shown. Use #10 screw provided.

Important: This disc prevents toilet from moving on
floor.

6. Lower toilet onto closet ange until nuts on closet bolts

go through rectangular holes in metal brackets, seal rests

on closet ange, and leg locates over locating disc.

4.

Make sure white
f o r k - s h a p e d
sl ides are in
forward posi­tion.

3. Turn the toilet upside-down and install closet ange seal
on Slide-EZ Valve with at side against toilet.

Electrical Hookup

RV and Marine Models

Connect your 12-Volt or 24-Volt model Electra Magic
directly to the appropriate D.C. source as a separate circuit.
Use minimum size #14 gauge wire. (Black wire to positive
[hot], white to negative [ground].)

Important – Be sure polarity of power supply has been
properly determined and correctly connected to lead wires
before operating.

4

MULTIPLE POSITIONS
SUMP DISCHARGE

Side Discharge

Rear Discharge

Installation

Marine Model

CAUTION: Toilet is not explosion proof and must not be

located in an area where an explosive atmosphere exists,
such as gasoline fumes, etc.

1. Install white fork­shaped slides on
brackets. Make one
right bracket as­sembly and one left
bracket assembly.

(Right bracket assembly shown.)

2. Mount bracket assemblies and sump to bottom of toilet
with four screws. Brackets are sandwiched between sump
and toilet.

3. Locate toilet position with template and install bolts

in oor drilling 7/32” dia. hole in oor, putting acorn
nut on screw, and driving bolts into oor with wrench.

Remove acorn nuts.

4. Also using template, locate position for plastic locator

disc. Drill 5/32” dia. hole in oor and fasten disc to oor
with at sides oriented parallel to sides of toilet.

Important: This disc prevents toilet from moving on
floor.

5. Install one nut on each bolt and screw nuts down until they

touch top of gauge. If
gauge is misplaced,
bottom surface of nuts
should be 1.34 in. (3.4

cm) above oor.

6. Lower toilet over bolts until nuts go through rectangular
holes in metal brackets, and the unit rests on its feet.

Marine Installation Instructions continue on Page 5.