DUAL VOLTAGE REFRIGERATORS
120 VOL TS AC AND 12/24 VOL TS DC
INST ALLATION AND OWNER’S
MANUAL
Service Information
If service or parts are required, contact the nearest Norcold Service Center . To find an
authorized Norcold Service Center near you, please telephone the Norcold Customer
Support Dept. at 800-543-1219 (option-1) or visit our web site at www.norcold.com.
Norcold Customer Support Dept.
Telephone : 800-543-1219
Fax : 937-497-3183
Web Site: www.norcold.com
Model No. Serial No.
Part No. 622089F
7/06
#5490-301-0100
NORCOLD AC/DC Models - Two Year Limited Warranty Policy
Norcold, Inc. warrants that when properly installed and placed under normal service and
use its refrigeration equipment is free from defects in material and workmanship for two
years commencing from
Limitations of Warranty
1. This Warranty is the only warranty for a Norcold AC/DC refrigerator . This Warranty
does not extend to glassware, electric light bulbs, and replaceable fuses.
2. This warranty does not apply to parts and assemblies that have been subjected to
misuse, improper installation, abnormal service, transit damage, recharging of cooling
system,
accident, fire, improper repair, tampering or abuse.
the original date of purchase of the new equipment.
3. Irrespective of the nature of the warranty protection offered or claimed, the period of
warranty shall in no case extend beyond two years commencing from
of purchase of the new equipment.
the original date
Limitation of Remedy
1. The responsibility of NORCOLD under this or any warranty is limited to the repair or
replacement (at NORCOLD’S option) of the defective part or assembly .
2. In no event and under no circumstances shall NORCOLD be responsible under this
Limited Warranty for any other charge whatsoever , including but not limited to charges
or claims for labor, lost business, lost time, lost profit s, loss of use, or any kind of
incidental or consequential damages, however denominated or described. The remedy
under this warranty is limited to repair or replacement.
3. Some states do not allow the exclusion or limitation of incidental or consequential
damages, so the above exclusion may not apply to you.
Disclaimer of Other Warranties
This Warranty is expressly in lieu of all other warranties either expressed or implied. All
other warranties, expressed or implied, including any warranty of merchantability or fitness
for a particular purpose, are hereby disclaimed and excluded.
Legal Rights
This Warranty gives you specific legal rights, and you may have other legal rights which
vary from state to state.
2
Safety Awareness
Read this manual carefully and understand the contents before you install the refrigerator .
Be aware of possible safety hazards when you see the safety alert symbol on the
refrigerator and in this manual. A signal word follows the safety alert symbol and identifies
the danger of the hazard. Carefully read the descriptions of these signal words to fully
know their meanings. They are for your safety .
WARNING: This signal word means a hazard, which if ignored, can cause
dangerous personal injury, death, or much property damage.
CAUTION: This signal word means a hazard, which if ignored, can cause small
personal injury or much property damage.
Model No. and Serial No.
The model and serial number are on a label which is inside the refrigerator on the left
side and on the cover of this manual.
Operation
This refrigerator is made for refrigerating purposes and operates on120 volts AC and
12/24 volts DC power supplyieswhen installed as written in this manual.
NOTE: The refrigerator operates automatically on AC or DC power . When both
power sources are supplied to the refrigerator, it defaults to AC. When the
refrigerator is disconnected from the shoreline power (when AC power is
no longer available), the refrigerator switches to DC operation.
CAUTION: Never store combustible materials near the refrigerator. S toring
combustible materials near the refrigerator creates a safety hazard and also
decreases the ventilation of the cooling system which decreases the refrigerator
performance.
Do not touch the evaporator or other metal parts inside the refrigerator cabinet with
wet hands because they can freeze to the refrigerator.
Always disconnect all power sources from the refrigerator when doing routine
maintenance. Have service work done only by a qualified service technician.
The refrigerator temperature is controlled by a thermostat, located on the panel above the
door. A green power light, located on the p anel comes on when the refrigerator is “ON”.
Number “1” is the warmest and number “5” is the coldest thermostat position. For
efficient operation, change the thermostat according to the types of food stored and the
ambient temperature.
If you are not going to use the refrigerator for an extended period of time, put the thermostat to the “OFF” position.
3
Over Heating Shut-off Device Operation (DE0240T & DE0251T)
Operating the refrigerator in high ambient temperatures can over heat the cooling unit and
cause premature failure of the compressor. (See the label inside the refrigerator .)
T o protect the cooling unit from over heating, the refrigerator will automatically shut-off when
the vehicle air temperature is higher than approximately 130° F. If shut off occurs, an
audible alarm tone (an intermittent beeping) operates from the refrigerator.
T o stop the audible alarm tone and restart the refrigerator , turn the thermostat counterclockwise to the “OFF” position and then clockwise to the desired thermostat position.
The refrigerator will not restart until the air temperature is lower than approximately
130° F.
Protection System
Your refrigerator has an over current protection system in the electronic circuit to
prevent damage to the inverter which may occur due to a reverse polarity connection.
If the refrigerator does not operate and the green power light does not come on, check
the fuse, which is located on the side of the inverter case, and the polarity of the DC
power supply. If the refrigerator still does not operate, another problem can exist in
the inverter. Have an authorized Norcold Service Center check the refrigerator.
Cleaning and Defrosting
Defrosting
It is normal for frost to collect on the freezer plate inside the refrigerator. Excess frost
decreases the cooling performance of the refrigerator. Defrost the refrigerator as necessary.
CAUTION: Do not use sharp objects, a hair dryer , a heat gun, etc. to defrost the
refrigerator. Damage to the interior of the refrigerator can occur .
- Turn the thermost at to “OFF”.
- Remove all food from the refrigerator.
NOTE: Defrosting the refrigerator makes excess water inside the refrigerator.
- Put dry towels (etc.) inside the refrigerator to absorb the excess water.
- Put trays of hot water in the freezer until the frost is melted.
4
- Empty the drip tray .
- Remove the wet towels (etc.) and dry the inside of the refrigerator
- Turn the thermost at to the desired setting.
- Put the drip tray and all food in the refrigerator.
Cleaning
A good time to clean the refrigerator is just af ter you defrost it.
Clean the inside of the refrigerator as often as necessary to avoid food odors:
- Remove all food from the refrigerator.
NOTE: Do not use abrasive cleaners, chemicals, or scouring pads because they can
- Wash the inside of the refrigerator and the door gasket with a solution of liquid dish
- Rinse with clean water and dry.
- Af ter cleaning, put a thin coating of petroleum jelly on the hinge side of the gasket to
damage the inside of the refrigerator.
detergent and warm water.
keep it soft and to prevent it from rolling.
Battery Maintenance
Over cooling drains your battery
- When the ambient temperature is between 70° and 90° F, keep the thermostat at the “3“
position to avoid an excessive drain of the battery . When making ice, or storing frozen
foods, turn the thermostat to the coldest setting “5“.
Maintain the battery
If the charge of your battery is not sufficient, the cooling performance of your refrigerator
decreases.
CAUTION: Only use a “quick charger” on the battery if the thermostat is turned to
“OFF”.
Check the Battery charge Level
A fully charged battery will have a specific gravity reading of between 1.260 and 1.280. The
battery voltage is best indicated when the refrigerator is “ON” and the battery charging system is “OFF”. Charge the battery when the specific gravity reading is less than 1.200.
5
For your reference
The wiring diagram shown below is recommended for dual battery hookup (See
Art01516)
.
*Recommended source:
Sure Power Industries, Inc.
1-800-845-6269
www.Surepower.com
Installation
The refrigerator should be located and secured on a solid surface in the vehicle.
Before installing the refrigerator into the opening, make sure the DC supply is properly
connected. In many cases, the DC supply can be connected from outside the vehicle
by means of the baggage or access door.
Measure the opening to determine if you have proper clearance for installation.
Additional insulation space around the refrigerator is not necessary .
6
Be sure the refrigerator is not in direct sunlight or near a gas stove, a heater, or other
heat-generating appliances. Avoid inst alling your refrigerator close to warm water lines
or warm air ducts.
Y our refrigerator was thoroughly cleaned before shipment from the factory .
It is advisable, however, to clean the interior once more before using. Wipe the interior
with a cloth and warm water. Then wipe with a dry cloth.
Ventilation
Sufficient ventilation (airflow) over the rear mounted condenser of the refrigerator is
necessary for the refrigerator to operate correctly (See Art01582).
* NOTE: The fan will operate only when
the ambient temperature is
higher than approximately 95° F .
CAUTION: Do not remove the
bottom rails from the refrigerator
cabinet. The rails supply space
under the refrigerator that is necessary for correct ventilation.
If you do not make sure that the
ventilation is correct, a shortened
refrigerator life expectancy , poor
refrigeration, continuous operation,
accelerated battery discharge and a
void warranty will result.
Installation Options
Install a decorative door panel
NOTE: The decorative door panel must be
4 mm or less in thickness.
1. Remove the door from the refrigerator
by removing the two (2) bolts that attach
the door hinge to the bottom of the
refrigerator (See Art01583).
Air outlet
Air inlet
Rails
Fan*
Art01582
7
2. Remove the panel retainer by removing
the two (2) screws that attach the panel
retainer (See Art0151 1).
3. Gently pull the door panel out of the
door (Art01512).
4. Push a new door panel into the door
slot.
CAUTION: Do not overtighten the
screws and bolts.
5. Put the panel retainer in the original
location and attach with two (2) screws.
6. Put the door in the original location and
tighten the two (2) bolts.
Reverse the door swing:
1. Remove the door from the refrigerator
by removing the two (2) bolts that attach
the door hinge to the bottom of the
refrigerator
2. Remove the two (2) bolts that attach the
upper hinge.
Door latch plate
Bolts
3. Remove the bolt that attaches the door
latch plate to the top of the refrigerator
(See Art01513).
4. Remove the upper hinge and the door
latch plate from the refrigerator.
5. Att ach the upper hinge and the door
latch plate to the opposite sides of the
refrigerator.
Art01513
8
6. Move the latch to the opposite side of
the door (See Art01514):
- Remove the screw that attaches the
hinge insert to the door.
- Remove the hinge insert, the latch
handle, and the coil spring from the
door.
- Pull the latch handle pin out of the
recess in the latch handle.
- Move the latch handle pin to opposite
side of the latch pin (See Art01515).
- Turn the latch handle up side down and
push the latch handle pin into the
recess of the latch handle.
- Make sure the angled top faces
the door latch plate.
- Assemble the coil spring, the latch
handle, and the hinge insert into the
opposite side of the door.
- Install and tighten the screw that
attaches the hinge insert to the door.
7. Put the door onto the refrigerator
8. Install and tighten the two (2) screws
that attach the door hinge to the bottom
of the refrigerator.
9
Connect the 120 volts AC and 12 volts DC supplies
r
A
This refrigerator operates on 120 volts (60 hertz) AC current and 12/24 volts DC current
from a battery .
CAUTION: Only connect the refrigerator directly to the battery. Because they
often generate high voltage pulses and cause transistor defects in the inverter , no
other switches, lead wires, or electrical equipment should share the wiring between
the refrigerator and battery. Do not use an extension cord.
When using either a converter or a battery charger, make sure that they are connected in
parallel between the battery and the refrigerator . Do not use a converter or battery charger
to supply the DC power directly to the refrigerator because these two devices do not
supply filtered DC power (See Art01521).
Refrigerator Refrigerator
Transisterized
Battery charger or
AC/DC converter etc.
DC power supply
INCORRECT
Refrigerator
Transisterized
Battery charger or
C/DC converter etc.
CORRECT CORRECT
As the distance from the vehicle battery to the refrigerator increases, the correct AWG wire
size also increases. If he wire size is too small for the distance, a voltage drop occurs.
The voltage drop decreases the cooling performance of the refrigerator.
1. Norcold recommends that you use the following wire and fuse sizes:
- Measure the distance from the vehicle battery to the refrigerator:
- If the distance is less than 12 feet, use 16 A WG wire and a 10 Amp fuse.
- If the distance is between 12 and 20 feet, use 14 A WG wire and a 10 Amp fuse.
- If the distance is more than 20 feet, use 12 A WG wire and a 10 Amp fuse.
DC power supply
INCORRECT
Refrigerato
Art01521
10
- T wist the lead wires to reduce the radio interference and induction of a high voltage
surge from the outside (See Art01518).
INCORRECT CORRECT
Electrical equipment
Battery
Refrigerator Refrigerator
Art01518
2. Connect the DC power supply (See
Art01509):
- Remove the two (2) screws that attach
the junction cover.
- Remove the junction cover.
- Put each of the two (2) wires from the
battery through the ferrite core.
- Make a loop of the two (2) around and
back through the ferrite core.
- Put the two (2) wires through the
bushing of the junction cover.
- Push the DC input wires onto the DC
input terminals.
- Refer to the positive (+) and
negative (-) markings to make sure
that the connections are correct.
- Att ach the junction cover with the two
(2) screws.
Battery
Twist lead wires
- Put the two (2) wires through the wire
strain relief.
- Att ach the wire strain relief to the refrigerator cabinet with the self-tapping screw .
11
12
Loading...