A
B
K
J
E D C I H F
G
A:Modem Clips
B:Top Plate
C:Video Input (SDI or HDMI)
D:Mic/Line Audio Input
E:Headphone Output
F:Power Input
G:Power Switch
H:OLED Display
I:Status LEDs
J:Antennas
K: Modem Activity LEDs
*Modems not included
L |
|
P |
|
|
|
L: Video Input |
O: Fault/Error |
||
M |
||||
M: Encoder Status |
P: Stream Joystick |
|||
N |
|
|||
|
N: Broadcast/Record |
Q: Menu Joystick |
||
O |
||||
Q |
|
|||
|
|
|
||
Stream Joystick: |
|
|
||
▲, |
▲: Selects options from streaming/recording prompts |
|
WEB UI LOGIN |
|
● (button press): Returns to main status screen, start/stop recordings and broadcasts |
||||
username: admin |
||||
Menu Joystick: |
|
|||
|
password: admin |
|||
▲,▼: Select menu items, change status screen on main display, select characters |
|
|||
▲ |
: Back, move to higher menu level |
|
|
|
▲,● (button press): Confirm selection, open selected menu |
|
|
||
SETUP |
1 |
|
Connect a power source to Bond II’s DC input (F) and a video input to (C).
Connect one or more modems to Bond II’s USB ports. If desired, attach top plate, modem clips and velcro to secure the modems.
AC adapter |
HDMI |
SDI |
Use the included ¼"-20 and hot shoe mount to
attach Bond II to your camera.
DEVICE CONFIGURATION |
2 |
|
|
CONNECT TO BOND II |
|
•Via WiFi – Attach antennas to (J). Open your computer’s wireless network configuration and find Bond II’s WiFi network (Teranet – XXXX, where XXXX is the last four digits of Bond II’s serial number)
•Via Ethernet – Connect Bond II to a wired network or directly to your computer.
1.Open a web browser and enter the IP address of Bond II. View the WiFi IP address by pressing ▼ once and the Ethernet IP address by pressing ▼ twice.
2.Log into Bond II – The username is admin and the default password is admin.
CONFIGURE BONDING SETTINGS
1.Navigate to Video Setup > Bonding.
2.Enter a Sputnik Host Address. For Sputnik server setup instructions please see the Sputnik Setup Guide (http://www.teradek.com/pages/downloads).
3.Confirm the Sputnik Port matches your Sputnik server’s configured inbound port. The default value is 5111.
4.Adjust the Max Bitrate and Max Buffer Length settings, if desired.
5.Click Apply.
6.Confirm that data is reaching Sputnik by navigating to the server’s Dashboard, or by verifying activity on the modem activity LEDs (K).
BROADCAST CONFIGURATION |
3 |
|
|
||
Configure the following from the Video Setup > Stream Settings page. |
|
|
MPEG TRANSPORT STREAM |
|
|
1. Configure the following settings on Bond II. |
2. Configure the following settings on your decoder. |
|
|
|
Decoder |
|
Sputnik |
|
|
|
|
Primary Stream |
|
Decoder Settings |
Mode: MPEG Transport Stream |
|
Mode: MPEG Transport Stream |
Transport Stream Server: Enabled |
|
Protocol: TCP Pull |
Listening Port: 5000 |
|
Host: Your Sputnik Server Address Port: 5000 |
|
|
|
LIVESTREAM/USTREAM
1.Select Live Internet Streaming as the Stream Mode.
2.Select your provider.
3.Enter your user name and password, click login.
4.Select your Channel and click Apply.
5.Start/stop the stream with the buttons on the Stream Settings page or with the Stream Joystick.
RTMP STREAMING
1.Select RTMP as the Stream Mode.
2.Enter the server URL. Depending on your destination (local server or CDN), this will look similar to rtmp://server.address:1935/live.
3.Enter the stream name. For many platforms this is found with the server URL.
4.Click Apply.
5.Start/stop the stream with the buttons on the Stream Settings page or with the Stream Joystick.
NEED MORE HELP?
1.Support forum: http://support.teradek.com →Contains tips, information and all the latest firmware & software updates.
2.Training videos: http://www.teradek.com/training
TERADEK SUPPORT STAFF: support@teradek.com or call 888−941−2111 ext2 (Mon−Fri 7am to 6pm PST)
Loading...