Telefunken TF-1508 User Manual
RADIO WITH ALARM /
РАДИОПРИЁМНИК C БУДИЛЬНИКОМ
TF-1508
Instruction manual
Руководство по
эксплуатации
Instruction manual
Dear customer!
Thank you for purchasing our product. For safety, it is strongly recommended to read
this manual carefully before connecting, operating and/or adjusting the product and keep
the manual for future reference.
Description
Front panel
1. MODE button
2. SET button
3. ALARM button
4. VOL+ button
5. VOL- button
6. SNOOZE button
7. TURN- button
8. TURN+ button
9. RADIO button
MODE
RADIO
TURN+
SET
ALARM
VOL+
Back panel
1. Battery compartment
2. DISPLAY ON/OFF switch
3. AUX input
4. Power (DC6V) input
2
TURN-
S
NO OZ E
VOL-
Instruction manual
Utilization of the product
If you want to dispose of this product, do not
mix it with general household waste. There is a
separate collection system for used electronic
products in accordance with legislation that
requires proper treatment, recovery and
recycling.
Please contact your local authorities for
the correct method of disposal. By doing so,
you will ensure that your disposed product
undergoes the necessary treatment, recovery
and recycling and thus prevent potential
negative effects on the environment and
human health.
Important safeguards
• The instruction manual contains important
operating and maintenance instructions. For
your safety, it is necessary to refer to this
manual. Keep the manual for future use.
• Do not hit or drop the unit.
• Do not expose the unit to vibration, direct
sunlight, too high or low temperatures or
humidity.
• Do not disassemble the unit yourself.
Refer servicing to qualified service personnel.
• When the battery is exhausted, it should
be removed from the set to prevent leakage.
Power supply
Battery power
• Open the battery compartment cover.
Insert 4 x AA (1.5 V) batteries (not included).
Please observe correct battery polarities
or the unit will not work. Close the battery
compartment cover.
• When the batteries are exhausted, they
should be replaced.
• Do not use new and old batteries together.
Additional power
• Included with the receiver are 2 AG13
(1.5 V) batteries. The batteries are packed
separately and not inserted in the battery
compartment. This is an additional power
intended for saving the clock and alarm
settings. Without the additional power the time
and alarm settings will not be stored if the
power is switched off.
• When the batteries are exhausted they
should be replaced. New batteries should be
aquired by the user. Replace the batteries only
with batteries of the same type.
ATTENTION: The AG13 batteries are
consumables not covered by warranty, and
their failure (discharge) is not a ground for
addressing service and repair centers.
AC adaptor power
• Plug the supplied AC/DC power adaptor
into the power input on the back of the unit.
Connect the power cord to a power outlet.
Make sure the voltage is compatible.
• Always remember to disconnect the
power cord from the electrical mains before
unplugging it from the unit.
• Unplug the power cord from the mains
when not in use.
General operations
Clock
• In the clock mode press and hold the
SET button to enable the time setting mode.
Repeatedly press the SET button to set the
parameters in the following sequence: hours
=> minutes => year => month => date => exit.
The selected parameter will blink meaning
readiness for adjustment.
• Press the TURN+ button to adjust the
parameter up. Press the TURN- to adjust the
parameter down.
• Day of week will be set automatically.
• In the time setting mode, if no button is
pressed within 10 seconds after a parameter is
3
Instruction manual
selected, the unit will automatically go to
clock mode.
• In the time setting mode, press the MODE
button to return to the clock mode.
AUX input
To connect an external audio device (e.g.
an MP3-player), please use a standard stereo
cable with 3.5 mm to 3.5 mm plugs to connect
the audio line-out of the external device to the
AUX input socket of this unit (the cable should
be aquired separately).
LED display functions
• To save energy (when working on the
AC/DC adapter) or battery life (when working
on batteries), you can turn the display off by
switching the DISPLAY ON/OFF switch to the
OFF position. While in this mode you can turn
it on for 10 seconds by pressing any button or
by a loud sound (e.g. clapping your hands).
• The brightness of the display is set to half
from 22:00 to 6:59:59. Alternatively, press the
snooze button to adjust brightness manually.
Radio operation
• In the clock mode press the RADIO button
to switch the radio on.
• Press TURN+/TURN- buttons on the unit
to change the current frequency upwards
or downwards by 100 KHz. Press and hold
TURN+/TURN- buttons to search the nearest
strong signal station upwards or downwards
automatically.
• Hold MODE button, P01 will blink on
the screen. Press repeatedly TURN+/TURNbuttons to select the preset number for the
current frequency. Press MODE to save the
frequency in selected position (P01-P20).
• Press and hold the ALARM button: the
device will start scanning from the lowest
frequency and automatically save all available
stations in positions (up to 20). When stations
are saved in the memory, repeatedly press
TURN+/TURN- buttons to select the saved
stations.
Sleep Timer
• Press the SNOOZE button to set the
sleeping time of the radio, repeteadly press to
change the sleeping time interval from 10 to 90
minutes. When the time expires, the radio will
turn off.
During program saving, if no button is
pressed within several seconds, the unit will
return to the normal radio mode.
• To adjust volume, repeatedly press the
VOL+/VOL- buttons in the radio mode.
• Press MODE to switch the radio off.
Alarm operation
Alarm mode
• In clock mode, hold the ALARM button to
set the alarm time.
• Repeatedly press the ALARM button to
set the parameters in the following sequence:
hours => minutes => exit. While setting, the
digits will flash. Press the TURN+ or the
TURN- buttons to adjust the time. If no button
is pressed within 10 seconds after a parameter
is selected, the unit will automatically set the
alarm.
• If no button is pressed within 10 seconds in
the alarm mode, the unit will exit to the clock
mode.
Alarm ringing
• When setting the alarm, press RADIO,
then the playing radio station will be set as the
alarm (the playing radio frequency is set as the
last played radio frequency),
The alarm will ring for 15 minutes.
• If no radio station was set as an alarm
signal, then the unit will beep periodically.
• After setting the alarm, press the MODE
button to exit to the clock mode.
When setting radio as an alarm signal,
make sure the DISPLAY ON/OFF switch on the
back panel is switched to ON. Otherwise the
alarm will go off in standard beeping mode.
• Press the ALARM button to enter the alarm
mode, the “ALARM” indicator will appear on
4
4
Loading...