DPF100
Digital Picture Frame
1
2
27
3
26
4
Table of Content
Important Safeguards
Frequently Asked Questions
Quick Start Guide
Controls
Connecting to a TV Set
Remote Control
Insert the memory card
Control Functions
System setup
Glossary of Terms
Appendix (Troubleshooting Guide)
Technical Specifications
Service Providers in Australia
1
5
8
9
10
11
12
13
14
14
20
21
22
23
Warranty registration
25
5
Important Safeguards
IMPORTANT SAFEGUARDS
Signal Word Definitions
DANGER Indicates an imminently hazardous situation, which, if not avoided, will result in death
or serious injury. Usage of this signal word is limited to the most extreme situations.
WARNING Indicates a potentially hazardous situation, which, if not avoided, could result in
death or serious in jury.
CAUTION Indicates a potentially hazardous situation, which, if not avoided may result in
minor/moderate injury or product/property damage. It also alerts against unsafe practices.
WARNING: To reduce the risk of fire or shock hazard,do not expose this product to rain or moisture.
WARNING: To prevent the risk of electric shock, do not remove cover. No user-serviceable parts
inside. Refer servicing to qualified personnel.
WARNING--To reduce the risk of fire, electric shock, or serious personal injury:
• HEED WARNINGS. Adhere to all warnings in the operating instructions and on the Digital Picture
Frame itself.
• WATER AND MOISTURE. Do not use the unit near water or expose to rain or moisture.
• ATTACHMENTS. Use only manufacturer-recommended attachments or accessories.
• ACCESSORIES. Do not place the Digital Picture Frame on unstable cart, stand , tripod, bracket,
or table. The unit may fall, causing injury to you and serious damage to the product.
• VENTILATION. Position the Digital Picture Frame so that its location does not interfere with its
proper ventilation. For example, the unit should not be situated on a bed, sofa, rug or similar
surface that may block the ventilation opening, or placed in a built-in installation, such as a
book-case or cabinet, that may impede the plow of air through the ventilation openings.
• HEAT. Position the Digital Picture Frame away from sources of high heat such as radiators or
stoves.
• POWER SOURCE. Connect the Digital Picture Frame to a power supply only of the type
described in the operating instructions or as marked on the unit.
• GROUNDING OR POLARIZATION. This product may be equipped with a polarized alternating
current line plug (a plug having one blade wider than the other). This plug will fit into the power
outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet,
try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your
obsolete outlet. Do not defeat the safety purpose of the polarized plug.
• POWER CORD PROTECTION.
-Mains plug is used as the disconnect device. It shall remain readily operable and should not be
obstructed during intended use.
-Route power cords so that they are not likely to be walked on or
pinched by items placed on or against them, paying particular attention to the point where the cord
attaches to the Digital Picture Frame.
• OUTDOOR ANTENNA GROUNDING .If an outside antenna or cable system is connected to the
product, be sure the antenna or cable system is grounded so as to provide some protection against
voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA
70, provides information with regard to proper grounding of the mast and supporting structure,
READ ALL INSTRUCTIONS BEFORE USE.
24
6
Important Safeguards
grounding of the lead-in wire to an antenna
discharge unit, size of grounding conductors,
location of antennadischarge unit, connection
to grounding electrodes, and requirements
for the grounding electrode. See figure below.
•
•
LIGHTNING. For added protection for this
product during a lightning storm, or when it is
left unattended and unused for long periods of
time, unplug it from the wall outlet and disconnect
the antenna or cable system. This will prevent
damage to the product due to lightning and power
lines surges.
POWER LINES. An outside antenna system should not be located in the vicinity of overhead power
lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When
installing an outside antenna system, extreme care should be taken to keep from touching such power
lines or circuits as contact with them might be fatal.
• NON-USE. Unplug the power from the outlet when the unit is not in use.
• AVOIDING SURGES. For added protection during a lightning storm, unplug the Digital Picture Frame
from the wall outlet to prevent damage to the product due to power line surges.
• OVERLOADING. Do not overload wall out lets or extension cords.
• OBJECT AND LIQUID ENTRY. The apparatus shall not be exposed to dripping or Splashing and that
no objects filled with liquids, such as Vases, shall be placed the apparatus.
• DAMAGE REQUIRING SERVICE. Seek service by qualified service personnel when:
- The power supply has been damaged.
- Liquid has been spilled onto the Digital Picture Frame.
- The unit has been exposed to rain.
- The unit does not operate normally, or exhibits a marked change in performance.
- The unit has been dropped or physically damaged.
•
•
•
• SERVICING. Do not attempt to service the Digital Picture Frame beyond those means described in
these operating instructions. All other servicing should be referred to qualified service personnel.
REPLACEMENT PARTS. When replacement parts are required, be sure the service technician has
used replacement parts specified by the manufacturer or have the same characteristics as the original
part. Unauthorized substitutions may result in fire, electric shock, or other hazards.
SAFETY CHECK. Upon completion of any service or repairs to this product, ask the service
technician to perform safety checks to determine that the product is in proper operating condition.
WALL OR CEILING MOUNTING. The product should be mounted to a wall or ceiling only as
recommended by the manufacturer.
CAUTION-- To reduce the risk of personal injury or product/property damage:
• CLEANING. Clean the outer surface of the Digital Picture Frame (excluding the screen) gently
using a soft cloth dampened with water. Clean the screen only with a specified cleaning solution
for use with products such as laptops and computer monitors. These are available at most retail
consumer electronics stores. Do not clean the inside of the unit.
23
7
Condensation
If cold water is poured into a glass, water droplets form on the outside of the glass. This is called
condensation. Condensation may occur on internal operating parts of the product. Condensation
occurs:
• When the product is brought from the outdoors into a warm room, or if it is in a cold room which
is heated quickly.
• If the unit is moved suddenly from an air-conditioned room or car to a hot or humid location.
Should condensation occur, the product may not operate properly. WAIT 1-2 hours (to allow the
internal parts to adjust to the surrounding temperature) before using the product.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
Important Safeguards
This symbol alerts the user of the presence of non-insulated “dangerous voltage”
within the product’s enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to persons.
This symbol alerts the user of the presence of important operating and
maintenance (servicing) instructions in the Digital Picture Frame user guide.
CAUTION
TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT EXPOSE
THIS UNIT TO RAIN OR MOISTURE.
- CAUTION -
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING
TO QUALIFIED PERSONNEL.
Technical Specifications
Input Formats
®®,
Compact Flash (CF type I&II), Micro Driver (MD), Memory Stick
®
Memory Stick PRO , Multimedia Card (MMC), Secure Digital (SD),
USB Pen Drive.
Supported File
Formats
JPEG, Motion JPEG, AVI
Display
7"LCD monitor:480x234 resolution
Power Input
100V-240V AC, 50-60Hz
Power Output
12V DC, 1.5A
Weight 0.75 kg
Dimensions
26(W)x18(H)x3.5(D)cm
Image Effects
Rotate, zoom, pan, transitions, slide duration
Viewing Modes
Full frame 16:9/4:3 Standard Aspect Ratio, slide show or thumbnail
USB Host
V1.1
Output
Composite video output
System: PAL/NTSC
Analog 2-channel audio out
Earphone
Stereo Speakers(1Wx2)
22
8
Frequently Asked Questions
Q: How do 1 set up my Digital Picture Frame?
A: The Digital Picture Frame setup is very easy from “out-of-the-box” to “up-and-running” in a few
short minutes. Just plug the power adapter into the Power In jack on the back of the Digital Picture
Frame and plug the power cord into a standard 100-240 volt AC electrical outlet. Next, insert a
memory card into the appropriate slot on the side and slide the Power Switch to ON.
Q: What memory cards can the Digital Picture Frame read?
A: The Digital Picture Frame can read all popular memory cards in all sizes including the current
large capacity 2 GB cards and above, and 7card types including:
® TM ( ® ®
Compact Flash (CF type I & II), Micro Drive MD), Memory Stick (MS), Memory Stick PRO ,
TM TM
Multi Media Card (MMC), Secure Digital (SD).
Q: What media formats does the Digital Picture Frame support?
A: The Digital Picture Frame supports JPEG picture files, Motion JPEG, AVI video files WMA
audio files.
Q: I set up the Digital Picture Frame; why is it not powered on?
A: The adapter is not securely connected to the picture Frame or the Power Switch is not in the ON
position.
Q: I have a memory card in the Digital Picture Frame; why can’t I view the images?
A: First, make sure that the memory card is one of the card formats listed above and that the files
on the card are in one of the supported formats as listed above. Second, turn the Digital Picture Frame
OFF and make sure that the memory card is inserted all the way into the card slot and is facing the
correct direction. Third, turn the frame ON and from the initial card selection menu make sure that
you can select the card. Finally, make certain you are selecting the correct Mode from the next menu:
Picture for still images, Music for WMA music, or Video for AVI videos.
NOTE:
1. Some digital cameras save images in non-standard formats. Please refer to your camera’s
instruction manual for details.
Q: Why is the picture display slower with some pictures and faster with others?
A: Higher resolution pictures load more slowly. Try using lower resolution pictures or down sample
your images. See your camera’s operating manual for details on down sampling images.
Q: Can I insert multiple memory cards?
A: Yes. Turn on the unit after inserting memory cards. The first screen will display which types of
memory cards are in the slots. Use the Remote Control to the desired memory card.
Q: Does the Digital Picture Frame have built-in memory?
A: No, a compatible memory card must be used.
21
Appendix (Troubleshooting Guide)
Before contacting service personnel, please check possible causes according to the following
instructions.
Symptom Possible Cause Remedy
No power
1.Power supply not connected;
2.Bad contact between the power plug
and the receptacle;
3.The power of the receptacle is off;
4.Power switch is in the off position.
1.Incorrect signal connection;
2.The system is in the mute status.
No sound
No picture
No color
1.Incorrect signal connection;
2.Incorrect TV status;
1.Wrong selection of TV system;
2.Improper color adjustment;
3.Incorrect video output settings.
1.The remote control is not directed
at the sensor;
2.Low voltage of the RC batteries;
3.There is an obstacle between the
unit and RC.
Remote
control
malfunction
1.Connect to the power supply.
2.Plug again or replace a receptacle.
3.Switch on the receptacle.
4.Slide the power switch to on position.
1.Connect the signals properly.
2.Press the "Mute" button again.
1.Connect the signals properly.
2.Adjust the TV/AV status.
1.Setup the TV system see"system
setup/preference page/TV type" for
reference
2.Readjust the color.
3.Check if the video output settings are
correct.
1.Direct the remote control at the
sensor.
2.Change to a new battery.
3.Remove the obstacle.
No reader
memory card
1.The memory card is inserted all the
way into the card slot and is facing the
wrong direction;
2.The memory card did not insert
completely.
1.Insert the memory card with the
correct direction.
2.Insert the memory card completely.
9
Quick Start Guide
To begin using the Digital Picture Frame, follow these instructions:
1. Plug one end of the AC Adapter into the Digital Picture Frame
and plug the other end into a standard 100-240 volt AC electrical
outlet.
2. Insert a memory card into the appropriate slot.
NOTE: The card will only fit in one direction; do not force it. The
card should have a firm, snug fit if properly inserted.
3. Slide the Power Switch to the ON position.
4. If not already selected, scroll to the appropriate memory card
type on the first menu screen by using the Arrow Buttons on the
Remote Control.
5. Press the ENTER Button to confirm the selection.
6. On the next menu, scroll using the Arrow buttons to select
PHOTOS.
7. On the next menu, press SLIDESHOW on the Remote Control
to display images. For more details or instructions on using the
MUSIC, MOVIES, or FILES menus, refer to the “Control Functions”
section.
ON/OFF
20
Glossary of Terms
Aspect Ratio
The ratio of the length of an image to its width. Most computer screes and digital shoot
images that have an aspect ratio of 4:3.35mm film and some digital cameras shoot images
that have aspect ratio of 3:2.
AVI
®
Audio Video interleave; a Microsoft - specified format for saving audio and/ or video clips.
Flash Drive (Pen Drive)
A storage module made of flash memory chips that allow data to be easily transferred from
one device to another.
Flash Memory
A type of non-volatile memory that holds onto is contents even when an electrical charge
is not applied. Flash memory is used in many applications including PDAs, hardware WMA
players, and some digital cameras.
JPEG
Joint Photographic Experts Group; the development group for a compressed 24-bit
color image storage format that also bears its name.
Memory Card
The system used to store images by most digital cameras. Unlike a computer memory card,
this card retains data even without electricity.
Mega Pixel
One million pixels. A high mega pixel rating typically equates to a high maximum
performance for graphics, or better quality pictures for digital cameras.
Mp4
A container format allows combining of different multimedia streams into one single file.
Mp4 supports multimedia content such as audio, video, subtitles, and pictures and
advanced content such as animated graphics and DVD-like menus.
Resolution
The amount of pixels that are displayed on a screen measured in pixels horizontal by pixels
vertical, such as 1024x768. The higher the resolution, the more pixels can be displayed
and greater detail is displayed. Lower resolutions are interpreted and may lose detail.
Slideshow
A display of a series of selected images.
Thumbnail
A small representation of a larger graphic often used to display several graphics at once
and allowing easy sorting through images.
USB (Universal Serial Bus)
A protocol for transferring data to and from digital devices. Many digital cameras and
memory card readers connect to the USB port on a computer.
10
Contents
MENU
ENTER
AV OUT
USB
CF
MS
SD / MMC
-
C +
DC 7-12V
ON/OFF
ENTER
PREV/UP ARROW
/LEFT ARROW
NEXT/DOWN ARROW/
RIGHT ARROW
MENU BUTTON
SD/MMC SLOT
CF/MD SLOT
PUT: FLASH DRIVE USB
AUDIO/VIDEO
OUTPUT
EARPHONE
MS, MS PRO
AC ADAPTER JACK
SPEAKERS POWER SWITCH
19
TV TYPE:
Select TV system. Option include PAL and NTSC, and multi.
AUDIO:
To select the Audio Language. Option include English, French, Spanish, Chinese,
Japanese, Korean, Russian.
Subtitle:
Select the Subtitle Language. Option include English, French, Spanish, Chinese,
Japanese, Korean, Russian.
Default:
Reset all the setting of DPF to init default state.
Exit setup menu
Preference page
System Setup
.. Preference Page ..
TV Type
Audio
Subtitle
Default
Go To Preference Page
PAI
ENG
Exit Setup Menu
Exit Setup Menu
MENU
ENTER
AV OUT
11
VIDEO IN
AUDIO IN
WHITERED Yellew
Connecting to a TV Set
18
Video Setup:
Quality:
Sharpness:
Select High, Medium, Low
Brightness:
tune the brightness with a progress bar by using LEFT/RIGHT.
Contrast:
tune the brightness with a progress bar by using LEFT/RIGHT.
Hue:
tune the Hue with a progress bar by using LEFT/RIGHT.
Saturation:
tune the Saturation with a progress bar by using LEFT/RIGHT.
System Setup
3. Slide Show:
Set the display duration for each image: 1S, 3S, 5S.
SETUP: General setup
1.TV DISPLAY
NORMAL: Use this mode for viewing standard picture in unaltered proportions.
Which is the standard still image aspect ratio from most Digital Cameras.
Black bars will appear on each side of the screen.
WIDE: Use this mode to standard picture will stretch to fit the screen.
NOTE: If enduser can not get full size of screen picture, they can have the solution
to go to setup - TV wide
2.OSD Language
Select the OSD( On Screen Display) language (The language for all menus and
on-screen displays). Option include English, French, Spanish, German, Italian.
.. General Setup page ..
TV Display
OSD Lang
Slide Show
Wide
ENG
3S
Go To General Setup Page
.. Video Setup Page ..
Sharpness
Brightness
Contrast
Hue
Saturation
Go To Video Setup Page
MID
00
00
00
00
Remote Control
DIGITAL PICTURE FRAME
ENTER
SLIDE SHOW
SETUP
MENU
ZOOM
4:3
16:9
AUDIO
SUBTITLE
DISPLAY
PROG REPEAT
MUTE
/
VOL
1 2 3 4
5
6
7
8
9
10
11
12
13
14
16
15
19
18
17
20
21
22
23
1. MENU: Press MENU Return to the previous
menu.
2. MUTE: Press MUTE to temporary turns off
sound.
3. Display: Press Display to choose the"single
elapsed", "single remain" or "display off".
4. 4:3/16:9 : Press 4:3/16:9 to adjust aspect
ratio of screen display.
5.7.8.9.22: UP/DOWN/LEFT/RIGHT/ENTER:
USE UP/DOWN/LEFT/RIGHT Keys to
navigate all on-screen display, Press ENTER
to confirm selections.
Stop: Press STOP to stop video playback.
SETUP: Press SETUP to access setup menu.
Repeat: Press Repeat to Repeat file or folder.
6.
10.
11.PREV:Press PREV to previous file.
12.NEXT:Press NEXT to next image/VIDEO.
13.
14.PROG: Press PROG to show by file browse.
15.SUBTITLE:Press the SUBTITLE to select
the subtitle language.
12
1
2
CR2025
HOW TO REPLACE THE BATTERY
STEP 1: PUSH THE BUTTON TOWARD LEFT;
STEP 2: PULL THE BATTERY LOADER OUT.
BATTERIES
INCORRECT USE OF BATTERIES MAY CAUSE THEM TO LEAK, CORRODE OR EXPLODE.
Be sure to place the batteries in the correct direction.
It is dangerous to charge/heat/open or short-circuit the batteries.
Do not leave dead or expired batteries or mix old/new batteries.
When not using the remote control for a long duration of time, remove the batteries. When operating
range becomes reduced, replace all batteries with new, fresh ones.
If leakage from the battery occurs, wipe the battery liquid from the battery compartment, then replace.
16.AUDIO: Press AUDIO to select the audio language.
17. :Press" " to reverse at different times during.
18. : Press" " to forward at different times during.
19.
20.Zoom: Press Zoom to zoom in/out to magnify or reduce you view.
21.
23.
Slide Show: Press Slide Show to begin displaying picture in a slide show
Volume Controls: Adjust volume for audio and video file
Play/Pause: Press Play/Pause once to Pause video playback and press Play/Pause
again to resume Playback.
17
Control Functions Continue/System Setup
[ZOOM]:1.Press 'ZOOM' button repeatedly during playback, then the size of image
will change each press in the sequence as: 2X,3X,4X,1/2X,1/3X,1/4X,normal.
2.Use' , , , 'keys to move the zoomed image sa you like. There is a box on
the button right of the screen to indicate the zoom size and corresponding position
of the image.
3. To resume normal playback, press 'ZOOM' repeatedly until the image is in
normal size.
[VOLUME +,-]: Press "VOL+,VOL-"keys to decrease/ increase sound volume.
1.Use left/right keys to highlight "file" icam is in the "select mode" inside. Press
ENTER keys to file list background music play.
2.Press "PROG" key to make all documents compositor according to the document type.
3.Use UP/DOWN and / keys to highlight desired Audio file, then press ENTER
to start to playback the Audio file, and use "REPEAT" keys to setup repeat mode.
4.Use UP/DOWN and / to highlight image file then. Press ENTER to start to
playback image file, and "slide show" keys to play all image.
Background music play
VIDEO CONTROL
1.Use ' ' Keys to highlight VIDEO icon, Press 'Enter' Button enter VIDEO play
menu.
2.Use / keys to highlight a VIDEO file , then press PLAY button to start to play back the VIDEO file.
[PAUSE]: Press ' ' to pause during playback, and press Pause again to resume.
[STOP]: Press ' ' to stopping playing and press' ' again return to VIDEO file
browse menu.
[FORWARD /REVERSE ] : Press FORWARD/REVERSE to forward /reverse during
playback , and the playback speed will cycle with each press as : 2x, 4x, 8x, 16x,
32x, normal. Press' ' to pause and press' ' again to resume.
[ / ]: Press' / ' to switch playback to previous file .next to next file.
[DISPLAY]: Press 'DISPLAY' to choose the "single elapsed", "single remain"or
"display off"
/
/ /
Insert the memory card
1. Insert the SD/MMC memory card with the
correct direction.
2. Insert the CF memory card with the correct
direction.
3. Insert the MS/MS-PRO memory card with
the correct direction.
13
16
Normal the aspect ratio the screen.
NOTE: For WIDE mode and NORMAL mode see' SETUP/TV DISPLAY'
[PAUSE]: Press ' ' to pause during playback, and press Pause again to resume.
[STOP]: Press ' ' to stopping playing. Then the time showing on the bottom right
will switch to 00:00/00:00
[FORWARD /REVERSE ] : Press FORWARD/REVERSE to forward /reverse during
playback , and the playback speed will cycle with each press as : 2x, 4x, 8x, 16x,
32x, normal. Press' ' to pause and press' ' again to resume.
[UP/DOWN]: Use / Keys to highlight an WMA file when the selected one is
playing by using / keys . Then press ENTER, the highlight WMA will be
played instead of the previous one.
[VOLUME +,-]: Press "VOL+,VOL-"keys to decrease/ increase sound volume.
MUSIC CONTROL
/
1.Use / Keys to highlight MUSIC icon, Press 'Enter' Button enter music play menu.
2.Use / keys to highlight a WMA file , then press PLAY button to start to playback
the WMA file.
/ /
Control Functions Continue
16:9
ZOOM Press "ZOOM" button repeatedly during playback, then the size of image will change
each press in the sequence as: 100%, 125%, 150%, 200%,50%, 75%.
After the image is enlarged, use the arrow buttons" , , , " to move the image
so that you can view different of the enlarged image.
To resume normal playback, press"ZOOM" repeatedly until the image is in normal size.
4:3/16:9 Switch the aspect ratio the screen .
In the WIDE mode , Change view to standard 4:3 aspect ratio. Use this mode for
viewing standard photos in unaltered proportions. Recommend to do not use this
mode is In the NORMAL mode.
4:3
4:3 16:9
CARD SELECT MENU
At startup, a menu screen appears for selection of the memory card:
: Use the Right and Left Arrows on the Remote control or on the control panel to select the
correct memory card type or USB Flash driver.
MODE SELECTION MENU
The next menu allows Selection of the playback mode.
NOTE:
1. Some digital cameras save images in non-standard formats. Please refer to your camera’s
instruction manual for details.
2. The SD icon not highlight is during SD memory card not insert. The MS/PRO,CF,USB icon is
same too.
ENTER: Press the Enter button to confirm.
Control Functions Continue
14
15
Control Functions Continue.
Use the Arrow Buttons on the Remote Control Panel to select an image.
ENTER Press the ENTER Button from the Remote Control or the Control Panel to view the
selected image at full screen size.
MENU Press "MENU" button return to main menu.
When viewing an image:
In PHOTO mode, a thumbnail screen will appear to enable easy selection of images. This mode
displays a set of up to 9 thumbnail image on the screen at a time.
Previous: Press the Previous Button on the Remote Control or the Control Panel to return
to the previous image.
NEXT: Press the NEXT Button on the Remote Control or the Control Panel to skip to the
NEXT image.
Slide show: In the press the SLIDE SHOW Button on the Remote Control to begin a
“slide show” style playback of all image on the selected memory card..
STOP: Press the STOP Button on the Remote Control or the Control Panel to stop image
playback and return to the Thumbnail Screen
MENU Press "MENU" button to image fire browse menu.
ROTATE When viewing a full screen, Press direction button on the remote: UP(vertically mirror);
DOWN(horizontally mirror),LEFT(90 degree clockwise),RIGHT(90 degree anti clockwise)
THUMBNAIL SCREEN
IMAGE CONTROLS
Prev Next
PHOTO: JPEG still image viewing and slide show playback.
MUSIC: WMA audio playback.
VIDEO: Video file Playback.
FILE: View the file structure on the memory card.
: Use the Left and Right Arrows on the Remote Control or on the Control Panel to
select a viewing mode.
MENU: Press"MENU" button return to main menu.
NOTE: This menu only have to just appear is the memory card contain two kind of above
the support document.
Loading...