»
DM -4800
Digital Mixing Console
D00959010A
EFFECT LIST
2
TASCAM DM- 4800 Effect list
Contents
Effect Parameter List .......................3
TASCAM FX2.0 Effect Parameters ............ 3
MONO CHORUS FX2.0 .................................. 3
STEREO CHORUS FX2.0 ................................. 4
MONO FLANGER FX2.0 ................................. 6
STEREO FLANGER FX2.0 ................................ 7
COMPRESSOR FX2.0 ...................................... 9
DE-ESSER FX2.0 ........................................... 10
MONO DELAY FX2.0 .................................... 11
STEREO DELAY FX2.0 .................................. 13
DISTORTION FX2.0 ....................................... 15
EXCITER FX2.0 .............................................. 16
PHASER FX2.0 .............................................. 17
PITCH SHIFTER FX2.0 ................................... 18
TC Reverb Parameters ............................. 19
Balance Settings .......................................... 19
High Cut Filter ............................................. 19
Space Editor ................................................. 19
Decay ........................................................... 19
Pre-Delay ...................................................... 20
Effect Preset List ............................21
TC Reverb Presets .................................... 21
TASCAM FX2.0 Presets ............................25
DISTORTION FX2.0 ....................................... 25
MONO DELAY FX2.0 .................................... 25
STEREO DELAY FX2.0 .................................. 26
PHASER FX2.0 .............................................. 26
MONO CHORUS FX2.0 ................................ 27
STEREO CHORUS FX2.0 ............................... 27
MONO FLANGER FX2.0 ............................... 27
STEREO FLANGER FX2.0 .............................. 28
COMPRESSOR FX2.0 .................................... 28
EXCITER FX2.0 .............................................. 29
DE-ESSER FX2.0 ........................................... 29
PITCH SHIFTER FX2.0 ................................... 30
TASCAM DM- 4800 Effect list
3
Effect Parameter List
TASCAM FX2.0 Effect Parameters
MONO CHORUS FX2.0
This chorus effect features mono-in (one input) and
stereo-out (two outputs).
Table 1.1: Mono Chorus parameters
Parameter Indicator Range Description Remarks
LFO rate LFO Rate Freeze, 0.01 Hz - 30.00 Hz (0.01 Hz steps) Specifies LFO frequency.
LFO depth LFO Depth 0.0% - 100.0% (0.1% steps) Specifies LFO modula
-
tion depth.
Pre-delay Pre-Delay 0 ms - 500 ms
(0 ms - 9.99 ms: 0.01 ms steps;
10 ms - 99 ms: 1 ms steps;
100 ms - 500 ms: 10 ms steps)
Specifies time between
onset of original sound
and onset of the effect
sound.
Using this parameter
enables you to make
interesting and detailed
settings based on subtle
changes due to phase
cancellation.
Feedback
amount
Feedback
Amt
0% - 90% (1% steps) Specifies amount of
delay line output signal
returned to delay line
input.
Feedback
inversion
InvertFbk Off, On Determines whether
or not feedback path
output signal will be
inverted.
LFO waveform
type
LFO Type Off, Sine, Triangle, Sawtooth Up, Sawtooth
Down, Square
Specifies LFO waveform
type.
LFO softening LFO Smooth 0.0% - 100.0% (0.1% steps) Specifies low-pass filter
coefficient applied to
LFO waveform.
This parameter improves
unnatural sound at
discontinuous points by
smoothening out edges
of sawtooth or square
waveform.
Dry delay DryDly
(Thru 0)
0.0% - 100.0% (0.1% steps) Specifies delay of dry
signal that simulates
“ through zero” flanging.
Low shelving
filter frequency
LoShelfFreq 20.000 Hz - 20.00 kHz (6 cents steps) Specifies low shelving
filter corner frequency.
This filter is applied to
feedback loops.
Low shelving
filter gain
LoShelfGain –20.0 dB - 0.0 dB (0.1 dB steps) Specifies low shelving
filter gain.
This filter is applied to
feedback loops.
High shelving
filter frequency
HiShelfFreq 20.000 Hz - 20.00 kHz (6 cents steps) Specifies high shelving
filter corner frequency.
This filter is applied to
feedback loops.
High shelving
filter gain
HiShelfGain –20.0 dB - 0.0 dB (0.1 dB steps) Specifies high shelving
filter gain.
This filter is applied to
feedback loops.
Effect parameter list
Effect parameter list
4
TASCAM DM- 4800 Effect list
Parameter Indicator Range Description Remarks
Wet signal
output pan
Wet Pan 100%L - Center - 100%R (1% steps) Specifies pan for wet
signal output to L and R
channels.
Dry signal
output pan
Dry Pan 100%L - Center - 100%R (1% steps) Specifies pan for dry
signal output to L and R
channels.
R output phase
inversion
Wide Mode Off, On Determines whether
or not phase of right
channel output will be
inverted.
STEREO CHORUS FX2.0
This chorus effect features stereo-in and stereo-out.
Table 1.2: Stereo Chorus parameters
Parameter Indicator Range Description Remarks
L channel LFO
rate
L LfoRate Freeze, 0.01 Hz - 30.00 Hz (0.01 Hz steps) Specifies LFO frequency.
L channel LFO
depth
L LfoDepth 0.0% - 100.0% (0.1% steps) Specifies LFO modula
-
tion depth.
L channel
pre-delay
L PreDly 0 ms - 500 ms
(0 ms - 9.99 ms: 0.01 ms steps;
10 ms - 99 ms: 1 ms steps;
100 ms - 500 ms: 10 ms steps)
Specifies time between
onset of original sound
onset of the effect
sound.
L channel
feedback
amount
L FbkAmt 0% - 90% (1% steps) Specifies amount of
delay line output signal
returned to delay line
input.
R channel LFO
rate
R LfoRate Linked, Freeze, 0.01 Hz - 30.00 Hz
(0.01 Hz steps)
Specifies LFO frequency.
R channel LFO
depth
R LfoDepth Linked, 0.0% - 100.0% (0.1% steps) Specifies LFO modula
-
tion depth.
R channel
pre-delay
R PreDly Linked, 0 ms - 500 ms
(0 ms - 9.99 ms: 0.01 ms steps;
10 ms - 99 ms: 1 ms steps;
100 ms - 500 ms: 10 ms steps)
Specifies time between
onset of original sound
and onset of the effect
sound.
R channel
feedback
amount
R FbkAmt Linked, 0% - 90% (1% steps) Specifies amount of
delay line output signal
returned to delay line
input.
L channel LFO
waveform type
L LfoType Off, Sine, Triangle, Sawtooth Up, Sawtooth
Down, Square
Specifies LFO waveform
type.
Effect parameter list
TASCAM DM- 4800 Effect list
5
Parameter Indicator Range Description Remarks
L channel LFO
softening
L LfoSmooth 0.0% - 100.0% (0.1% steps) Specifies low-pass filter
coefficient applied to
LFO waveform.
This parameter improves
unnatural sound at
discontinuous points by
smoothening out edges
of sawtooth or square
waveform.
L channel dry
delay
L DryDly 0.0% - 100.0% (0.1% steps) Specifies delay of dry
signal that simulates
“ through zero” flanging.
L channel
feedback
inversion
L InvertFbk Off, On Determines whether
or not feedback path
output signal will be
inverted.
R channel LFO
waveform type
R LfoType Linked, Off, Sine, Triangle, Sawtooth Up,
Sawtooth Down, Square
Specifies LFO waveform
type.
R channel LFO
softening
R LfoSmooth Linked, 0.0% - 100.0% (0.1% steps) Specifies low-pass filter
coefficient applied to
LFO waveform.
This parameter improves
unnatural sound at
discontinuous points by
smoothening out edges
of sawtooth or square
waveform.
R channel dry
delay
R DryDly Linked, 0.0% - 100.0% (0.1% steps) Specifies delay of dry
signal that simulates
“ through zero” flanging.
R channel feed
-
back inversion
R InvertFbk Linked, Off, On Determines whether
or not feedback path
output signal will be
inverted.
Low shelving
filter frequency
LoShelfFreq 20.000 Hz - 20.00 kHz (6 cents steps) Specifies low shelving
filter corner frequency.
This filter is applied to
feedback loops.
Low shelving
filter gain
LoShelfGain –20.0 dB - 0.0 dB (0.1 dB steps) Specifies low shelving
filter gain.
This filter is applied to
feedback loops.
High shelving
filter frequency
HiShelfFreq 20.000 Hz - 20.00 kHz (6 cents steps) Specifies high shelving
filter corner frequency.
This filter is applied to
feedback loops.
High shelving
filter gain
HiShelfGain –20.0 dB - 0.0 dB (0.1 dB steps) Specifies high shelving
filter gain.
This filter is applied to
feedback loops.
Input cross feed
amount
In X-Feed 0% - 100% (1% steps) Specifies amount of L
(R) channel input signal
sent to R (L) channel
delay line.
Cross feedback
amount
Fbk X-Feed 0% - 100% (1% steps) Specifies amount of L (R)
channel feedback signal
sent to R (L) channel
feedback path.
Effect parameter list
6
TASCAM DM- 4800 Effect list
Parameter Indicator Range Description Remarks
Output wet
cross feed
Wet X-Feed 0% - 100% (1% steps) Specifies pan for L/R wet
channel outputs.
With 0%, L channel wet
signal is output from L
channel, and R channel
wet signal is output
from R channel. With
100%, L channel wet
signal is output from R
channel and R channel
wet signal is output
from L channel.
Mixture Mixture 0% - 100% (1% steps) Specifies mix ratio of
dry feedback delay sig
-
nal and LFO modulation
signal.
MONO FLANGER FX2.0
This anger effect features mono-in and stereo-out.
It uses the same algorithm as the chorus effects, and
the parameters are identical to the mono chorus parameters.
Table 1.3: Mono Flanger parameters
Parameter Indicator Range Description Remarks
LFO rate LFO Rate Freeze, 0.01 Hz - 30.00 Hz (0.01 Hz steps) Specifies LFO frequency.
LFO depth LFO Depth 0.0% - 100.0% (0.1% steps) Specifies LFO modula-
tion depth.
Pre-delay Pre-Delay 0 ms - 500 ms
(0 ms - 9.99 ms: 0.01 ms steps;
10 ms - 99 ms: 1 ms steps;
100 ms - 500 ms: 10 ms steps)
Specifies time between
onset of original sound
and onset of the effect
sound.
Using this parameter
enables you to make
interesting and detailed
settings based on subtle
changes due to phase
cancellation.
Feedback
amount
FeedbkAmt 0% - 90% (1% steps) Specifies amount of
delay line output signal
returned to delay line
input.
Feedback
inversion
InvertFbk Off, On Determines whether
or not feedback path
output signal will be
inverted.
LFO waveform
type
LFO Type Off, Sine, Triangle, Sawtooth Up, Sawtooth
Down, Square
Specifies LFO waveform
type.
LFO softening LFO Smooth 0.0% - 100.0% (0.1% steps) Specifies low-pass filter
coefficient applied to
LFO waveform.
This parameter improves
unnatural sound at
discontinuous points by
smoothening out edges
of sawtooth or square
waveform.
Dry delay DryDly
(Thru 0)
0.0% - 100.0% (0.1% steps) Specifies delay of dry
signal that simulates
“ through zero” flanging.
Effect parameter list
TASCAM DM- 4800 Effect list
7
Parameter Indicator Range Description Remarks
Low shelving
filter frequency
LoShelfFreq 20.000 Hz - 20.00 kHz (6 cents steps) Specifies low shelving
filter corner frequency.
This filter is applied to
feedback loops.
Low shelving
filter gain
LoShelfGain –20.0 dB - 0.0 dB (0.1 dB steps) Specifies low shelving
filter gain.
This filter is applied to
feedback loops.
High shelving
filter frequency
HiShelfFreq 20.000 Hz - 20.00 kHz (6 cents steps) Specifies high shelving
filter corner frequency.
This filter is applied to
feedback loops.
High shelving
filter gain
HiShelfGain –20.0 dB - 0.0 dB (0.1 dB steps) Specifies high shelving
filter gain.
This filter is applied to
feedback loops.
Wet signal
output pan
Wet Pan 100%L - Center - 100%R (1% steps) Specifies pan for wet
signal output to L and R
channels.
Dry signal
output pan
Dry Pan 100%L - Center - 100%R (1% steps) Specifies pan for dry
signal output to L and R
channels.
R output phase
inversion
Wide Mode Off, On Determines whether
or not phase of right
channel output will be
inverted.
STEREO FLANGER FX2.0
This anger effect features stereo-in and stereoout. It uses the same algorithm as the chorus effects
and the parameters are identical to the stereo chorus
parameters.
Table 1.4: Stereo Flanger parameters
Parameter Indicator Range Description Remarks
L channel LFO
rate
L LfoRate Freeze, 0.01 Hz - 30.00 Hz (0.01 Hz steps) Specifies LFO frequency.
L channel LFO
depth
L LfoDepth 0.0% - 100.0% (0.1% steps) Specifies LFO modula
-
tion depth.
L channel
pre-delay
L PreDly 0 ms - 500 ms
(0 ms - 9.99 ms: 0.01 ms steps;
10 ms - 99 ms: 1 ms steps;
100 ms - 500 ms: 10 ms steps)
Specifies time between
onset of original sound
onset of the effect
sound.
L channel
feedback
amount
L FbkAmt 0% - 90% (1% steps) Specifies amount of
delay line output signal
returned to delay line
input.
R channel LFO
rate
R LfoRate Linked, Freeze, 0.01 Hz - 30.00 Hz
(0.01 Hz steps)
Specifies LFO frequency.
R channel LFO
depth
R LfoDepth Linked, 0.0% - 100.0% (0.1% steps) Specifies LFO modula
-
tion depth.
R channel
pre-delay
R PreDly Linked, 0 ms - 500 ms
(0 ms - 9.99 ms: 0.01 ms steps;
10 ms - 99 ms: 1 ms steps;
100 ms - 500 ms: 10 ms steps)
Specifies time between
onset of original sound
and onset of the effect
sound.
Effect parameter list
8
TASCAM DM- 4800 Effect list
Parameter Indicator Range Description Remarks
R channel
feedback
amount
R FbkAmt Linked, 0% - 90% (1% steps) Specifies amount of
delay line output signal
returned to delay line
input.
L channel LFO
waveform type
L LfoType Off, Sine, Triangle, Sawtooth Up, Sawtooth
Down, Square
Specifies LFO waveform
type.
L channel LFO
softening
L LfoSmooth 0.0% - 100.0% (0.1% steps) Specifies low-pass filter
coefficient applied to
LFO waveform.
This parameter improves
unnatural sound at
discontinuous points by
smoothening out edges
of sawtooth or square
waveform.
L channel dry
delay
L DryDly 0.0% - 100.0% (0.1% steps) Specifies delay of dry
signal that simulates
“ through zero” flanging.
L channel
feedback
inversion
L InvertFbk Off, On Determines whether
or not feedback path
output signal will be
inverted.
R channel LFO
waveform type
R LfoType Linked, Off, Sine, Triangle, Sawtooth Up,
Sawtooth Down, Square
Specifies LFO waveform
type.
R channel LFO
softening
R LfoSmooth Linked, 0.0% - 100.0% (0.1% steps) Specifies low-pass filter
coefficient applied to
LFO waveform.
This parameter improves
unnatural sound at
discontinuous points by
smoothening out edges
of sawtooth or square
waveform.
R channel dry
delay
R DryDly Linked, 0.0% - 100.0% (0.1% steps) Specifies delay of dry
signal that simulates
“ through zero” flanging.
R channel
feedback
inversion
R InvertFbk Linked, Off, On Determines whether
or not feedback path
output signal will be
inverted.
Low shelving
filter frequency
LoShelfFreq 20.000 Hz - 20.00 kHz (6 cents steps) Specifies low shelving
filter corner frequency.
This filter is applied to
feedback loops.
Low shelving
filter gain
LoShelfGain –20.0 dB - 0.0 dB (0.1 dB steps) Specifies low shelving
filter gain.
This filter is applied to
feedback loops.
High shelving
filter frequency
HiShelfFreq 20.000 Hz - 20.00 kHz (6 cents steps) Specifies high shelving
filter corner frequency.
This filter is applied to
feedback loops.
High shelving
filter gain
HiShelfGain –20.0 dB - 0.0 dB (0.1 dB steps) Specifies high shelving
filter gain.
This filter is applied to
feedback loops.
Input cross feed
amount
In X-Feed 0% - 100% (1% steps) Specifies amount of L
(R) channel input signal
sent to R (L) channel
delay line.
Effect parameter list
TASCAM DM- 4800 Effect list
9
Parameter Indicator Range Description Remarks
Cross feedback
amount
Fbk X-Feed 0% - 100% (1% steps) Specifies amount of L (R)
channel feedback signal
sent to R (L) channel
feedback path.
Output wet
cross feed
Wet X-Feed 0% - 100% (1% steps) Specifies pan for L/R wet
channel outputs.
With 0%, L channel wet
signal is output from L
channel, and R channel
wet signal is output
from R channel. With
100%, L channel wet
signal is output from R
channel and R channel
wet signal is output
from L channel.
Mixture Mixture 0% - 100% (1% steps) Specifies mix ratio of
dry feedback delay sig
-
nal and LFO modulation
signal.
COMPRESSOR FX2.0
This stereo compressor features feed forward and
feedback types, and RMS and Peak level detect
modes.
Table 1.5: Stereo Compressor parameters
Parameter Indicator Range Description Remarks
Attack time Attack 0 ms - 125 ms (1 ms steps) Specifies time taken for
compression to be ap
-
plied after input signal
level exceeds userdefined threshold.
Release time Release 5 ms - 5000 ms (1 ms steps) Specifies time taken
for compression to be
released after input sig
-
nal level reaches below
user-defined threshold.
Compression
ratio
Ratio 1:1 - 1:infinity Specifies ratio of com
-
pression applied to in
-
put signal that exceeds
user-defined threshold.
Threshold Threshold –40.0 dB - 0.0 dB (0.1 dB steps) Specifies signal level
that triggers compres
-
sor.
Compressor
type
CompType FeedForward, FeedBack Specifies type of com
-
pressor. With FeedFor
-
ward, signal that passed
level detector is com
-
pressed. With FeedBack,
signal before level
detector is compressed.
With FeedBack, com
-
pression will be applied
lightly.
Effect parameter list
10
TASCAM DM- 4800 Effect list
Parameter Indicator Range Description Remarks
Compressor
level detect
mode
CompMode RMS, Peak Determines whether
level detector uses peak
value or RMS value to
calculate gain reduc
-
tion.
Auto make-up
gain
AutoGain Off, On Turns on or off the func
-
tion that automatically
correct output gain level
reduced by compressor.
Auto make-up
gain bias
AutoBias –100% - 100% (1% steps) Fine adjusts differences
in auto make-up gain
amount between Peak
and RMS compressor
level detect modes, or
between FeedForward
and FeedBack types.
DE-ESSER FX2.0
The De-Esser features a relative threshold function
that allows the threshold to automatically change
depending on the input signal level. It also enables
you to monitor each of three-band side-chain signals.
Table 1.6: Stereo De-Esser parameters
Parameter Indicator Range Description Remarks
Monitor source Output
Monitor
Audio Path, Side Band Specifies whether to
monitor signal output
that passed through deesser, or to monitor sideband signal that was
removed from input.
Band 1 bias Filter1 Bias 0.0% - 100.0% (0.1% steps) Specifies how much
Band 1 (as a side chain)
affects other bands.
Band 2 bias Filter2 Bias 0.0% - 100.0% (0.1% steps) Specifies how much
Band 2 (as a side chain)
affects other bands.
Band 3 bias Filter3 Bias 0.0% - 100.0% (0.1% steps) Specifies how much
Band 3 (as a side chain)
affects other bands.
Relative
threshold
Relative
Thrsh
–40 dB - 0.0 dB (0.1 dB steps) Specifies de-esser
threshold relative to
input level.
You can apply de-esser
to input signal regard
-
less of signal level.
Maximum gain
reduction
MaxGainRdx –40 dB - 0.0 dB (0.1 dB steps) Specifies de-esser’s
maximum gain reduc
-
tion value.
Band 1
high-pass filter
frequency
HiPass1
Freq
1.00 kHz - 10.00 kHz (1 cent steps) Specifies high-pass filter
corner frequency.
Band 1
Effect parameter list
TASCAM DM- 4800 Effect list
11
Parameter Indicator Range Description Remarks
Band 1 low-pass
filter frequency
LoPass1
Freq
1.00 kHz - 10.00 kHz (1 cent steps) Specifies the low-pass
filter corner frequency.
Band 1
Band 2
high-pass filter
frequency
HiPass2
Freq
1.00 kHz - 10.00 kHz (1 cent steps) Specifies high-pass filter
corner frequency.
Band 2
Band 2 low-pass
filter frequency
LoPass2
Freq
1.00 kHz - 10.00 kHz (1 cent steps) Specifies low-pass filter
corner frequency.
Band 2
Band 3
high-pass filter
frequency
HiPass3
Freq
1.00 kHz - 10.00 kHz (1 cent steps) Specifies high-pass filter
corner frequency.
Band 3
Band 3 low-pass
filter frequency
LoPass3
Freq
1.00 kHz - 10.00 kHz (1 cent steps) Specifies low-pass filter
corner frequency.
Band 3
MONO DELAY FX2.0
This mono delay enables you to set a delay time
equal to twice the stereo delay time, and control various parameters related to the envelope follower.
Table 1.7: Mono Delay parameters
Parameter Indicator Range Description Remarks
Delay time DelayTime 1 ms - 2700 ms (1 ms steps) Specifies delay time be
-
fore initial echo begins.
Feedback delay
time
FbkDlyTime Linked, 1 ms - 2700 ms (1 ms steps) Specifies delay time
after initial echo occurs.
With Linked, all echoes
follow delay time pa
-
rameter setting.
Feedback
amount
Feedback
Amt
0% - 90% (1% steps) Specifies amount of
audio signal returned to
delay input.
Feedback phase
inversion
InvertFbk Off, On Determines whether
or not feedback signal
phase will be inverted.
Low shelving
filter frequency
LoShelfFreq 20.000 Hz - 20.00 kHz (6 cents steps) Specifies low shelving
filter frequency.
This filter is applied to
feedback loops.
Low shelving
filter gain
LoShelfGain –20.0 dB - 0.0 dB (0.1 dB steps) Specifies low shelving
filter gain.
This filter is applied to
feedback loops.
High shelving
filter frequency
HiShelfFreq 20.000 Hz - 20.00 kHz (6 cents steps) Specifies high shelving
filter frequency.
This filter is applied to
feedback loops.
High shelving
filter gain
HiShelfGain –20.0 dB - 0.0 dB (0.1 dB steps) Specifies high shelving
filter gain.
This filter is applied to
feedback loops.
Wet signal
output pan
Wet Pan 100%L - Center - 100%R (1% steps) Specifies pan for wet
(delayed) audio output.
Dry signal
output pan
Dry Pan 100%L - Center - 100%R (1% steps) Specifies pan for dry
audio output.
Effect parameter list
12
TASCAM DM- 4800 Effect list
Parameter Indicator Range Description Remarks
Envelope target
parameter
Envelope
Trgt
WetDryMix, Output, FeedbackAmt, Wet
Pan, Dry Pan, LFO Frequency, LFO Gain,
HFD Frequency, HFD Gain, Both Frequency,
Both Gain
Selects a parameter that
is influenced by enve
-
lope follower output.
Parameter value will
change according to
value of the envelope
follower. The maximum
(or minimum) value
will be restricted by the
current parameter value
(not by the parameter's
maximum value). That
is, adjusting the value of
the selected target pa
-
rameter will enable you
to set the parameter
value range affected by
the envelope follower.
Envelope attack
time
EnvAtkTime 0 ms - 125 ms (1 ms steps) Specifies time taken
for envelope follower
value to rise to a new
value when signal input
to envelope follower
increases.
Envelope
release time
EnvRlsTime 5 ms - 5000 ms (1 ms steps) Specifies time taken for
envelope follower value
to decline to a new
value when signal input
to envelope follower
decreases.
Envelope bias EnvBias 0.0% - 100.0% (0.1% steps) Specifies envelope fol
-
lower output gain.
You can adjust the effec
-
tiveness of the envelope
follower output. This
affects how the selected
envelope target param
-
eter is adjusted via the
envelope parameters.
Envelope mode EnvMode Off, Env Normal, Env Inverted, Gate
Normal, Gate Inverted
Selects type of enve
-
lope follower output.
The envelope follower
generates DC signals at
a level that corresponds
to audio input level.
Refer to the table
footnote a) for more
information.
Gate open
threshold
GateOpen 0.0% - 100.0% (0.1% steps) Specifies the threshold
at which the envelope
follower gate is open.
Gate hold time GateHold 0 ms - 1000 ms (1 ms steps) Specifies the minimum
time before opened
gate is closed regardless
of input audio level.
This setting prevents
unwanted noise gen
-
erated by a gate that
frequently opens and
closes.
Effect parameter list
TASCAM DM- 4800 Effect list
13
Parameter Indicator Range Description Remarks
Gate close
threshold
GateClose 0.0% - 100.0% (0.1% steps) Specifies the threshold
at which the envelope
follower gate is closed.
a) In Normal Envelope mode, the envelope follower output level is relative to the audio input level. In Inverted Envelope mode, the envelope follower output level is maximized when no audio exists, and the output level declines as the
audio input level rises. In Normal Gate mode, the envelope follower output level becomes zero when the audio input
level does not reach the open threshold. The envelope follower level is maximized when the audio input level exceeds
the gate close threshold. In Inverted Gate mode, the envelope follower output level is maximized when the audio input
level does not reach the open threshold. The envelope follower level is zero when the audio input level exceeds the
gate close threshold.
STEREO DELAY FX2.0
This stereo delay enables you to create a multi-tap
delay sound using ve delay taps.
Table 1.8: Stereo Delay parameters
Parameter Indicator Range Description Remarks
Master tap
delay ratio
MstrTap
Ratio
0% - 200% (1% steps) Specifies delay time
ratio between each tap.
For example, when you
are making a rhythm
pattern with differ
-
ent tap delay settings,
adjusting this ratio
enables you to increase
or decrease the speed of
the rhythm pattern. You
do not need to adjust
each tap setting.
Master
feedback
amount
MstrFbk 0% - 90% (1% steps) Specifies amount of
audio signal returned to
delay input.
Delay type Delay Type Stereo, PingPong Selects Stereo mode or
PingPong mode.
Low shelving
filter frequency
LoShelfFreq 20.000 Hz - 20.00 kHz (6 cents steps) Specifies low shelving
filter frequency.
This filter is applied to
feedback loops.
Low shelving
filter gain
LoShelfGain –20.0 dB - 0.0 dB (0.1 dB steps) Specifies low shelving
filter gain.
This filter is applied to
feedback loops.
High shelving
filter frequency
HiShelfFreq 20.000 Hz - 20.00 kHz (6 cents steps) Specifies high shelving
filter frequency.
This filter is applied to
feedback loops.
High shelving
filter gain
HiShelfGain –20.0 dB - 0.0 dB (0.1 dB steps) Specifies high shelving
filter gain.
This filter is applied to
feedback loops.
Tap 1 delay
time
Tap1
DlyTime
Off - 1350 ms (1 ms steps) Specifies delay time of
delay tap.
With Off, no audio sig
-
nal will be output from
this tap delay.
Tap 2 delay
time
Tap2
DlyTime
Off - 1350 ms (1 ms steps) Specifies delay time of
delay tap.
With Off, no audio sig
-
nal will be output from
this tap delay.
Effect parameter list
14
TASCAM DM- 4800 Effect list
Parameter Indicator Range Description Remarks
Tap 3 delay
time
Tap3
DlyTime
Off - 1350 ms (1 ms steps) Specifies delay time of
delay tap.
With Off, no audio sig
-
nal will be output from
this tap delay.
Tap 4 delay
time
Tap4
DlyTime
Off - 1350 ms (1 ms steps) Specifies delay time of
delay tap.
With Off, no audio sig
-
nal will be output from
this tap delay.
Tap 1 gain
amount
Tap1Gain 0% - 100% (1% steps) Specifies amount of
audio signals feedback
from this tap to delay
input.
Tap 2 gain
amount
Tap2Gain 0% - 100% (1% steps) Specifies amount of
audio signals feedback
from this tap to delay
input.
Tap 3 gain
amount
Tap3Gain 0% - 100% (1% steps) Specifies amount of
audio signals feedback
from this tap to delay
input.
Tap 4 gain
amount
Tap4Gain 0% - 100% (1% steps) Specifies amount of
audio signals feedback
from this tap to delay
input.
Tap 5 delay
time
Tap5
DlyTime
Off - 1350 ms (1 ms steps) Specifies delay time of
delay tap.
With Off, no audio sig
-
nal will be output from
this tap delay.
Tap 6 delay
time
Tap6
DlyTime
Off - 1350 ms (1 ms steps) Specifies delay time of
delay tap.
With Off, no audio sig
-
nal will be output from
this tap delay.
Tap 7 delay
time
Tap7
DlyTime
Off - 1350 ms (1 ms steps) Specifies delay time of
delay tap.
With Off, no audio sig
-
nal will be output from
this tap delay.
Tap 8 delay
time
Tap8
DlyTime
Off - 1350 ms (1 ms steps) Specifies delay time of
delay tap.
With Off, no audio sig
-
nal will be output from
this tap delay.
Tap 5 gain
amount
Tap5Gain 0% - 100% (1% steps) Specifies amount of
audio signals feedback
from this tap to delay
input.
Tap 6 gain
amount
Tap6Gain 0% - 100% (1% steps) Specifies amount of
audio signals feedback
from this tap to delay
input.
Tap 7 gain
amount
Tap7Gain 0% - 100% (1% steps) Specifies amount of
audio signals feedback
from this tap to delay
input.
Effect parameter list
TASCAM DM- 4800 Effect list
15
Parameter Indicator Range Description Remarks
Tap 8 gain
amount
Tap8Gain 0% - 100% (1% steps) Specifies amount of
audio signals feedback
from this tap to delay
input.
DISTORTION FX2.0
This mono distortion enables pre-amp or power amp
modeling.
Table 1.9: Mono Distortion parameters
Parameter Indicator Range Description Remarks
Pre-amp gain PreAmpGain 0.00 - 11.00 (0.01 steps) Specifies input gain at
pre-amp section.
With the maximum set
-
ting (11.00), the input
signal gain is multiplied
110 times.
Pre-amp drive PreAmp
Drive
0.00 - 11.00 (0.01 steps) Sets distortion at preamp section.
Power amp
gain
PwrAmp
Gain
0.00 - 11.00 (0.01 steps) Specifies input gain at
power amp section.
With the maximum set
-
ting (11.00), the input
signal gain is multiplied
110 times.
Power amp
drive
PwrAmp
Drive
0.00 - 11.00 (0.01 steps) Sets distortion at power
amp section.
Routing Routing PreAmp+PwrAmp, PreAmp->PwrAmp,
PwrAmp->PreAmp, PreAmp, PowerAmp
Sets distortion routing.
Asymmetry Asymmetry –100.0% - 100.0% (0.2% steps) Adjusts DC offset at
power amp section.
Morph Morph 0.0% - 100.0% (0.1% steps) Specifies mix bal
-
ance between preamp distortion and
power amp distortion
when Routing is set to
PreAmp+PwrAmp. If the
value is closer to 0%,
more power amp distor
-
tion, and if it is closer
to 100%, more pre-amp
distortion.
Pre EQ type PreEq Type Parametric, Shelving, Stack, Big Bottom,
Wide, Phat Mid
Selects a preset com
-
bination of pre filter
frequency and Q.
Pre low filter
gain
Pre Low –15 dB - +15 dB (0.1 dB steps) Specifies pre low filter
gain.
Pre mid filter
gain
Pre Mid –15 dB - +15 dB (0.1 dB steps) Specifies pre mid filter
gain.
Effect parameter list
16
TASCAM DM- 4800 Effect list
Parameter Indicator Range Description Remarks
Pre high filter
gain
Pre High –15 dB - +15 dB (0.1 dB steps) Specifies pre high filter
gain.
Post EQ type PostEq Type Parametric, Shelving, Stack, StackOffAxis,
Combo, ComboOffAxis
Selects a preset com
-
bination of post-filter
frequency and Q.
Post low filter
gain
Post Low –15 dB - +15 dB (0.1 dB steps) Specifies post low filter
gain.
Post low-mid
filter gain
Post LowMid –15 dB - +15 dB (0.1 dB steps) Specifies post low-mid
filter gain.
Post mid filter
gain
Post Mid –15 dB - +15 dB (0.1 dB steps) Specifies post mid filter
gain.
Post high-mid
filter gain
Post HiMid –15 dB - +15 dB (0.1 dB steps) Specifies post high-mid
filter gain.
Post high filter
gain
Post Hi –15 dB - +15 dB (0.1 dB steps) Specifies post high filter
gain.
EXCITER FX2.0
The exciter effect features a high-performance harmonic generator.
Table 1.10: Exciter parameters
Parameter Indicator Range Description Remarks
Crossover
frequency
Crossover 500 Hz - 10.00 kHz (10 Hz steps) Specifies crossover
frequency of filter that
affects audio signal sent
to harmonic generator.
Harmonics will be
generated based on the
frequency range above
the crossover frequency.
Harmonics gain Harmonic
Gain
0% - 100% (1% steps) Specifies gain of har
-
monics generated
before they are mixed
with dry audio signals.
Harmonics
balance
HarmonicBal 0% - 100% (1% steps) Sets balance between
harmonics of frequency
components below and
above crossover points.
Effect parameter list
TASCAM DM- 4800 Effect list
17
PHASER FX2.0
The stereo phaser offers ve LFO waveforms.
Table 1.11: Stereo Phaser parameters
Parameter Indicator Range Description Remarks
LFO rate LFO Rate Freeze, 0.01 Hz - 30.00 Hz (0.01 Hz steps) Specifies LFO frequency.
Negative (Yin)
LFO depth
Yin Depth 0.0% - 100.0% (0.1% steps) Specifies modulation
depth of negative side
of LFO.
Positive (Yang)
LFO depth
Yang Depth 0.0% - 100.0% (0.1% steps) Specifies modulation
depth of positive side of
LFO.
Master
resonance
MasterRes 0.0% - 200.0% (0.1% steps) Sets relative balance
between negative and
positive sides.
LFO waveform
type
LFO Type Off, Sine, Triangle, Sawtooth Up, Sawtooth
Down, Square
Specifies LFO waveform
type.
Negative (Yin)
stage
Yin Stages 1 stage - 32 stages (1 stage steps) Specifies the number of
stages for all-pass filter
cascaded on the nega
-
tive side.
Positive (Yang)
stage
Yang
Stages
1 stage - 32 stages (1 stage steps) Specifies the number of
stages for all-pass filter
cascaded on the positive
side.
Negative and
positive mix
balance
Yin/Yang
Mix
0% - 100% (1% steps) Sets relative balance
between negative and
positive sides before
mix.
Negative (Yin)
resonance
Yin Res 0.0% - 100% (0.1% steps) Specifies resonance
(filter efficiency) of each
all-pass filter stage.
Negative (Yin)
phase inversion
Yin Invert Off, On Determines whether or
not the output phase of
the audio path of nega
-
tive all-pass filter will be
inverted.
Positive (Yang)
resonance
Yang Res 0.0% - 100% (0.1% steps) Specifies resonance
(filter efficiency) of each
all-pass filter stage.
Positive (Yang)
phase inversion
Yang Invert Off, On Determines whether or
not the output phase of
the audio path of posi
-
tive all-pass filter will be
inverted.
Effect parameter list
18
TASCAM DM- 4800 Effect list
PITCH SHIFTER FX2.0
The stereo pitch shifter features a crossfade pitch
shift algorithm.
Table 1.12: Stereo Pitch Shifter parameters
Parameter Indicator Range Description Remarks
Semitones Semitones –12 - +12 (1 semitone steps) Specifies pitch shift by
semitones.
Cents Cents –50 - +50 (1 cent steps) Specifies the pitch shift
by cents.
Pre-delay PreDelay 1 ms - 500 ms (1 ms steps) Sets delay applied to au
-
dio signals before pitch
shifter.
Feedback
amount
Feedback
Amt
0% - 90% (1% steps) Specifies amount of
audio feedback from
pitch shifter to pre delay
input.
Portamento Portamento 0% - 100% (1% steps) Specifies “through rate”
applied when pitch shift
amount is changed.
Setting this parameter
could create a sound
similar to a portamento
control effect on a
synthesizer.
Crossfade time Crossfade 30 ms - 100 ms (1 ms steps) Specifies buffer size
assigned by sawtooth
waveform.
Longer crossfade time
would reduce un
-
naturalness but increase
group delay.
Effect parameter list
TASCAM DM- 4800 Effect list
19
TC Reverb Parameters
Table 1.13: TC Reverb parameters
Parameter Indicator Range Description Remarks
Balance Settings
Initial reflection
balance
I/R 50 - 0 - 50 (1 steps) Sets L/R balance of
initial reflection.
Tail balance TAIL 50 - 0 - 50 (1 steps) Sets L/R balance of
reverb tail.
High Cut Filter
Cutoff
frequency
HICUT 20 Hz - 16 kHz Specifies cutoff frequen
-
cy of high cut filter.
Attenuation ATT –40.0 dB - 0 dB
(0.1 dB steps)
Specifies attenuation
amount of high cut
filter.
Space Editor
Room shape SHAPE HALL, HORSESHOE, PRISM, FAN, CLUB,
SMALL
Specifies room shape to
simulate.
Room size SIZE 4% - 400% Specifies ratio of size of
simulated room to origi
-
nal room size.
Wall diffusion W-DIFF –50% - +50%
(0.1% steps)
Specifies how much
the room wall affects
sound. (A setting of 0%
simulates the original
room characteristics.)
Stereo width WIDTH 0% - 100% (1% steps) Specifies the width of
stereo image of rever
-
beration. (0%: mono,
100%: stereo)
Decay
Low band decay
time
LOW 0.25 s - 64.00 s Specifies decay time for
low band.
Mid band decay
time
MID 0.25 s - 64.00 s Specifies decay time for
mid band.
High band
decay time
HIGH 0.25 s - 64.00 s Specifies decay time for
high band.
Scaling range RANGE 4 s, 16 s, 64 s Selects decay time
range.
Crossover point X-over LOW 20 Hz - 16 kHz Specifies crossover point
between low and mid
bands.
Effect parameter list
20
TASCAM DM- 4800 Effect list
Parameter Indicator Range Description Remarks
Crossover point X-over HIGH 20 Hz - 16 kHz Specifies crossover point
between mid and high
bands.
Pre-Delay
Initial reflection
level
INILEV Off, –140 dB - 0.0 dB
(–140 dB - –60 dB: 5 dB steps;
–59 dB - –20 dB: 1 dB steps;
–19.9 dB - 0.0 dB: 0.1 dB steps)
Specifies initial reflec
-
tion level.
Reverb level REVLEV Off, –140 dB - 0.0 dB
(–140 dB - –60 dB: 5 dB steps;
–59 dB - –20 dB: 1 dB steps;
–19.9 dB - 0.0 dB: 0.1 dB steps)
Specifies level of reverb
decay curve.
Initial reflection
pre-delay time
IR DLY 0 ms - 160 ms (1 ms steps) Specifies delay time
until initial reflection
starts.
Reverb delay
time
TAILDY 160 ms - 260 ms (1 ms steps) Specifies delay time
until reverb decay curve
starts.
TASCAM DM- 4800 Effect list
21
Effect Preset List
TC Reverb Presets
Preset Bank 1 contains presets for TC Reverb.
These presets are divided into the following catego-
ries.
Ambience
Creates natural acoustic environment, not a clearlyframed reverb.
Box
Contains many reverberations.
Chamber
Simulates a room acoustic.
FX
Creates unnatural, special effect sound.
Tunnel
Simulates a thin, long space.
Hall
Simulates a larger space. Various sizes and different
structures are available as space settings.
Drum
Reverb settings suitable for drum sound.
Perc
Reverb settings suitable for percussion or percussive
instrument.
Plate
Simulates vintage plate reverb sound.
Room
Simulates a space smaller than a hall.
Table 1.14: TC Reverb Preset List
No. Name Indicator
000 Ambience - Bright 1 Ambi- Bright 1
001 Ambience - Bright 2 Ambi- Bright 2
002 Ambience - Bright 3 Ambi- Bright 3
003 Ambience - Dark Ambi- Dark
004 Ambience - Midnight Ambi- Midnight
005 Ambience - Mornin' Vocal Ambi- MorninVocal
006 Ambience - Soft 1 Ambi- Soft 1
007 Ambience - Soft 2 Ambi- Soft 2
008 Ambience - Space Ambi- Space
009 Box - Bright Box- Bright
010 Box - Dark Box- Dark
011 Chamber - Large, Dark Chmb- Large, Dark
012 Chamber - Small Chmb- Small
013 Chamber - Small, Dark Chmb- Small, Dark
014 Chamber - Very Small Chmb- Very Small
015 FX - Big Barrel Space FX- BigBarrelSpce
016 FX - Big Pre Delay Slap FX- BigPreDlySlap
017 FX - Bright Cymbals FX- BrightCymbals
018 FX - Drum Boom Slap FX- DrumBoom Slap
019 FX - Dry After Taste FX- DryAfterTaste
Effect preset list
Effect preset list
22
TASCAM DM- 4800 Effect list
No. Name Indicator
020 FX - Icy Shower FX- Icy Shower
021 FX - Lost in Space FX- Lost in Space
022 FX - Neighbor (Hallway) FX- NeighborHallw
023 FX - Neighbor 2 (Floor) FX- NeighborFloor
024 FX - Not so Dry After Taste FX- NotsoDryAfter
025 FX - Short Non- Lin Like FX- Short Non- Lin
026 FX - Slap Back FX- Slap Back
027 FX - Steel Works FX- Steel Works
028 FX - Steel Works 2 FX- Steel Works 2
029 FX - Subtle Slapback FX- SubtleSlapbac
030 FX - Take Off FX- Take Off
031 FX - Tight Bounce Around FX- Tight Bounce
032 FX - Ultra Bright FX- Ultra Bright
033 FX - Under The Surface FX- Under Surface
034 FX - Wet After Taste FX- WetAfterTaste
035 FX - Wet After Taste w/Rain FX- W.A.T w_Rain
036 FX - Wood Floor FX- Wood Floor
037 Tunnel - Bright Tunn- Bright
038 Tunnel - Dark Tunn- Dark
039 Tunnel - Tube Tunn- Tube
040 Hall - Big Bright Hall- Big Bright
041 Hall - Big Clear Hall- Big Clear
042 Hall - Big Predelayed Hall- BigPredelay
043 Hall - Big Warm Hall- Big Warm
044 Hall - Cathedral 12s Hall- Cathdral12s
045 Hall - Cathedral 7s Hall- Cathedral7s
046 Hall - Church Hall- Church
047 Hall - Dome Hall- Dome
048 Hall - Huge Clear Hall- Huge Clear
049 Hall - Huge Warm Hall- Huge Warm
050 Hall - Last Row Stadium Con Hall- LastRowStdm
051 Hall - Lush Ballad Hall- Lush Ballad
052 Hall - Medium Bright Hall- Med.Bright
053 Hall - Medium Clear Hall- MediumClear
054 Hall - Medium Warm Hall- Medium Warm
055 Hall - Outside the Stadium Hall- OutsideStdm
056 Hall - Small Bright Hall- SmallBright
Effect preset list
TASCAM DM- 4800 Effect list
23
No. Name Indicator
057 Hall - Small Clear Hall- Small Clear
058 Hall - Small Warm Hall- Small Warm
059 Hall - Stage Hall- Stage
060 Hall - Warm Vocal Hall- Warm Vocal
061 Drum - Boom Room Drum- Boom Room
062 Drum - Drum Booth Drum- Drum Booth
063 Drum - Huge Low Tubular Drum- HugeLowTubu
064 Drum - Low Tubular Drum- Low Tubular
065 Drum - Snare Hall Drum- Snare Hall
066 Drum - Snare Room Drum- Snare Room
067 Drum - Subtle Kick Boom Drum- SubtleKick
068 Perc - Big Bright Perc- Big Bright
069 Perc - Bi g Clear Perc- Big Clear
070 Perc - Bi g Warm Perc- Big Warm
071 Perc - Medium Bright Perc- Med.Bright
072 Perc - Medium Clear Perc- MediumClear
073 Perc - Medium Warm Perc- Medium Warm
074 Perc - Small Bright Perc- SmallBright
075 Perc - Small Clear Perc- Small Clear
076 Perc - Small Room Perc- Small Room
077 Perc - Small Warm Perc- Small Warm
078 Plate - Big Bright Plat- Big Bright
079 Plate - Big Clear Plat- Big Clear
080 Plate - Big Warm Plat- Big Warm
081 Plate - Tight Plat- Tight
082 Room - Bathroom Room- Bathroom
083 Room - CD Master Room- CD Master
084 Room - Dark &Mellow 5 sec Room- Dark&Mellow
085 Room - Dry House Room- Dry House
086 Room - Empty Garage Room- EmptyGarage
087 Room - Empty Room Room- EmptyRoom
088 Room - Empty Room,Small Room- EmptyRoom S
089 Room - Large Garage Room- LargeGarage
090 Room - Percussion Room Room- Perc Room
091 Room - Small Room- Small
092 Room - Small Damped Room Room- S Dmp Room
093 Room - Small Yet Big Room- SmallYetBig
Effect preset list
24
TASCAM DM- 4800 Effect list
No. Name Indicator
094 Room - Small Yet Big w/Pre Room- S.Y.B w_Pre
095 Room - Stage Room- Stage
096 Room - Vocal Booth Room- Vocal Booth
097 Room - Vocal Dry Room- Vocal Dry
098 Room - Vocal Room Room- Vocal Room
099 Room - Vocal Room 2 Room- Vocal Room2
Effect preset list
TASCAM DM- 4800 Effect list
25
Table 1.15: TASCAM FX2.0 Preset List
Effect
Type
Preset
No.
Title Indicator Description
DISTORTION FX2.0
0 Plexi 60 Plexi 60 Simulates a typical 60's British stack amp tone, suitable
for a high-voltage, bright and crunchy British rock
sound.
1 Brit 80 Brit 80 Simulates a typical 80's British stack amp tone, suitable
for a more powerful rock and metal sound with added
gain.
2 Brit 2000 Brit 2000 Simulates a typical 2000's British stack amp tone,
suitable for a high-voltage, aggressive, contemporary
heavy metal sound.
3 CA Combo CA Combo Simulates a type of California tube combo amp.
4 CA Recti Stack CA Recti Stack Simulates a type of high-gain stack tube amp with
massive distortion, having a rectifier.
5 Tweed Tweed Simulates a typical 60's bluesy and mellow vintage
tweed amplifier.
6 Blackface Lux Blackface Lux Simulates the clean tube tone of 70's combo amps.
7 Class A-30 Class A-30 Simulates a type of crunchy 60's UK combo amp.
MONO DELAY FX2.0
8 Simple Basic Delay Simple Basic Dly Basic, general-purpose delay
9 Simple Vocal Delay Simple Vocal Dly Basic delay setting for vocals
10 Rockabilly Delay Rockabilly Short Rockabilly flavored short delay
11 Sizzle Delay Sizzle Dly Decaying sound features sizzling high components.
12 Guitar Ducking Delay Gtr Ducking Dly Delay sound starts after the fundamental instrument
sound stops.
13 Spring Reverb Delay Spring Revrb Dly This delay simulates spring reverb.
14 ENV Panning Delay ENV Panning Dly Panning via envelope
15 Basic Delay (Insert) Basic Dly (Insrt) Simple Basic Delay (#8) for insert
16 Vocal Delay (Insert) Vocal Dly (Insrt) Simple Vocal Delay (#9) for insert
17 Rockabilly (Insert) Rockabilly (Ins) Rockabilly Delay (#10) for insert
18 Sizzle Delay (Insert) SizzleDly (Insrt) Sizzle Delay (#11) for insert
19 ENV Pan Delay (Insert) ENV PanDly (Ins) ENV Panning Delay (#12) for insert
20 Mono>Stereo Delay Mono to St Delay Short delay with the pan setting of “L: Dry” and “R:
Wet” expands mono sound to stereo image.
Preset Bank 2 contains presets for TASCAM FX2.0.
TASCAM FX2.0 Presets
Effect preset list
26
TASCAM DM- 4800 Effect list
Effect
Type
Preset
No.
Title Indicator Description
STEREO DELAY FX2.0
21 Basic Stereo Delay BasicStereoDelay Basic stereo delay
22 Keyboard Stereo Delay Keyboad St Delay Suitable for stereo musical instruments, such as key
-
boards.
23 Deep Keyboard Delay DeepKeyboadDelay Delay with more depth, suitable for stereo musical
instruments.
24 PingPong Delay PingPong Delay This delay flows the output of each channel into the
other, back and forth (between left and right) like a
game of ping pong.
25 Non Linear Delay NonLinearDelay Reversed rotary stereo delay
26 ST Tap Delay 1 ST Tap Delay 1 This delay creates an irregular delayed phrase based
on Stereo Tap Delay Tempo 120.
27 ST Tap Delay 2 ST Tap Delay 2 This delay creates an irregular delayed phrase based
on Stereo Tap Delay Tempo 120.
28 ST Tap Delay 3 ST Tap Delay 3 This delay creates an irregular delayed phrase based
on Stereo Tap Delay Tempo 120.
29 Basic Stereo Delay
(Insert)
BasicStDly (Ins) Basic Stereo Delay (#21) for insert
30 Keyboard Stereo Delay Keyboad St (Ins) Keyboard Stereo Delay (#22) for insert
31 Deep Keyboard Delay
(Insert)
DeepKeyb. (Insrt) Deep Keyboard Delay (#23) for insert
32 PingPong Delay (Insert) PingPngDly (Ins) PingPong Delay (#24) for insert
33 Non Linear Delay
(Insert)
NonLinDly (Insrt) Non Linear Delay (#25) for insert
34 ST Tap Delay 1 (Insert) StTapDly1 (Insrt) ST Tap Delay 1 (#26) for insert
35 ST Tap Delay 2 (Insert) StTapDly2 (Insrt) ST Tap Delay 2 (#27) for insert
36 ST Tap Delay 3 (Insert) StTapDly3 (Insrt) ST Tap Delay 3 (#28) for insert
PHASER FX2.0
37 Light Phaser Light Phaser General-purpose phaser for a lighter effect
38 Mid Phaser Mid Phaser General-purpose phaser for more effect
39 Deep Phaser Deep Phaser General-purpose phaser for a deeper effect
40 Rhodes Phaser Rhodes Phaser Suitable for an electric piano.
41 Retro Lead Guitar Retro LeadGuitar Suitable for a retro guitar solo.
42 Light Keyboard Light Keyboard Use this phaser on a keyboard or synthesizer for a
lighter effect.
43 Mid Keyboard Mid Keyboard Use this phaser on a keyboard or synthesizer for more
effect.
44 Deep Keyboard Deep Keyboard Use this phaser on a keyboard or synthesizer for a
deeper effect.
45 Alien Phaser Alien Phaser This phaser creates a strange, unusual effect.
Effect preset list
TASCAM DM- 4800 Effect list
27
Effect
Type
Preset
No.
Title Indicator Description
MONO CHORUS FX2.0
46 Basic Mono Chorus Basic Mno Chorus Basic mono chorus
47 Light Mono Chorus Light Mno Chorus Use this chorus on a synthesizer or keyboard for a
lighter effect.
48 Deep Mono Chorus Deep Mno Chorus Use this chorus on a synthesizer or keyboard for a
deeper effect.
49 Piano Mod Chorus Delay Piano MOD ChoDly This chorus adds modulated delay and spread to piano
or lead sounds.
50 Vocal Doubler Vocal Doubler This chorus simulates vocal unison.
51 Alien Voice Alien Voice This chorus adds strange, sci-fi effects similar to what
you imagine alien voices might sound like.
52 Computer Voice Computer Voice This chorus creates a computerized voice effect.
53 Honky tonk Piano Honkytonk Piano This chorus creates a honky tonk piano effect when
applied to a piano sound.
STEREO CHORUS FX2.0
54 Basic Stereo Chorus Basic ST Chorus Basic stereo chorus
55 Light Stereo Chorus Light ST Chorus Lighter stereo chorus
56 Deep Stereo Chorus Deep ST Chorus Deeper stereo chorus
57 Delay Chorus (AUX) DelayChorus (AUX) Delay and stereo chorus are applied at the same time.
58 Stereo Chorus 1 (AUX) ST Chorus1 (AUX) Lighter stereo chorus for AUX
59 Stereo Chorus 2 (AUX) ST Chorus2 (AUX) Deeper stereo chorus for AUX
60 Horror Hit (AUX) Horror Hit (AUX) Suitable for SFX.
61 Space Laser (AUX) SpaceLaser (AUX) Suitable for SFX.
62 Early Reflection (AUX) EarlyReflct (AUX) This chorus simulates the reverberation of a small
room.
MONO FLANGER FX2.0
63 Basic Flanger Mono BasicFlangerMono Basic flanger
64 Light Flanger Mono LightFlangerMono Lighter flanger
65 Deep Flanger Mono Deep FlangerMono Deeper flanger
66 Mu-Tron Flanger MutronFlanger This flanger simulates a Mu-Tron type flange sound.
67 Light Phasing Light Phasing Lighter phasing sound
68 Deep Phasing Deep Phasing Deeper phasing sound
69 Metal Flanger Metal Flange Metallic flanger sound
70 Metallic Room Metallic Room This flanger simulates metallic room reverberation
sound.
71 Always Down Mono Always Down MNO This flanger creates a continuously descending sound.
72 Always Up! Mono Always Up! MNO This flanger creates continuously ascending sound.
73 Glitch Modulator GlitchModulator This flanger simulates a metallic glitch sound.
Effect preset list
28
TASCAM DM- 4800 Effect list
Effect
Type
Preset
No.
Title Indicator Description
STEREO FLANGER FX2.0
74 Basic Flanger ST Basic Flanger ST Basic stereo flanger
75 Light Flanger ST Light Flanger ST Lighter stereo flanger
76 Deep Flanger ST Deep Flanger ST Deeper stereo flanger
77 More Deep Flanger MoreDeepFlanger Much deeper stereo flanger
78 Light Phasing ST Light Phasing ST Lighter stereo phasing
79 Mid Phasing ST Mid Phasing ST Deeper stereo phasing
80 Deep Phasing ST Deep Phasing ST Much deeper stereo phasing
81 Metallic Room ST Metallic Room ST This flanger features stereo input and simulates metal
-
lic room reverberation sound.
82 Always Down ST Always Down ST This stereo flanger creates a continuously descending
sound.
83 Always Up! ST Always Up! ST This stereo flanger creates a continuously ascending
sound.
84 Metallic Release Metallic Release This flanger adds metallic release sound.
COMPRESSOR FX2.0
85 Soft Comp Soft Comp This compressor compresses the sound lightly.
86 Fat Comp Fat Comp This compressor equalizes input sound pressure levels
to create a fat sound.
87 Punchy Comp Punchy Comp This compressor creates a punchy sound by enhancing
the attack.
88 More Punchy Comp More Punchy Comp This compressor significantly enhances the attack.
89 Vocal Comp 1 Vocal Comp 1 This compressor adds moderate compression to a vo
-
cal.
90 Vocal Comp 2 Vocal Comp 2 This compressor adds remarkable compression to a
vocal.
91 Vocal Limiter Vocal Limiter Use this limiter for vocal parts that contain significant
level differences, such as shouting.
92 Guitar Comp Guiter Comp This compressor is suitable for a funky guitar sound
with fast attack.
93 Bass Comp Bass Comp This compressor equalizes the bass attack level to
increase sound pressure.
94 Pumpy Drum Loop PumpyDrumLoop This setting significantly enhances attack. Use it for
drum loops to emphasizes strong attack.
Effect preset list
TASCAM DM- 4800 Effect list
29
Effect
Type
Preset
No.
Title Indicator Description
EXCITER FX2.0
95 Basic Exciter Basic Exciter Basic exciter
96 Vocal Exciter 1 Vocal Exciter 1 Light exciter for vocal
97 Vocal Exciter 2 Vocal Exciter 2 Strong exciter for vocal
98 Guitar Dist Excitr GuiterDistExcitr This exciter emphasizes a guitar distortion sound.
99 Rock Piano Rock Piano This exciter emphasizes the mid range to create gran
-
deur in a rocking piano sound.
100 Rock Bass Rock Bass This exciter emphasizes the mid range slightly to cre
-
ate rock-bass sound.
101 Hi-Fi Drum Loop Hi-Fi Drum Loop This exciter turns a Lo-Fi drum loop that is lacking high
range into a Hi-Fi sound.
102 Low Range Cut Low Range Cut This exciter gets rid of mid and low ranges completely.
Applying this to a drum loop would leave only a hi-hat
sound.
103 Brass Exciter 1 Brass Exciter 1 This exciter emphasizes a glittering brass sound.
104 Brass Exciter 2 Brass Exciter 2 This exciter emphasizes a glittering brass sound.
105 Telephone Voice Telephone Voice This exciter simulates a voice talking through tele
-
phone.
DE-ESSER FX2.0
106 Basic De-esser Basic De-esser Basic de-esser
107 Female De-esser 1 Female De-esser1 Frequency target of this de-esser is adjusted for a
woman's voice.
108 Female De-esser 2 Female De-esser2 Frequency target of this de-esser is adjusted for a
woman's voice.
109 Female De-esser 3 Female De-esser3 Frequency target of this de-esser is adjusted for a
woman's voice.
110 Female De-esser 4 Female De-esser4 Frequency target of this de-esser is adjusted for a
woman's voice.
111 Male De-esser 1 Male De-esser 1 Frequency target of this de-esser is adjusted for a
man's voice.
112 Male De-esser 2 Male De-esser 2 Frequency target of this de-esser is adjusted for a
man's voice.
113 Male De-esser 3 Male De-esser 3 Frequency target of this de-esser is adjusted for a
man's voice.
114 Male De-esser 4 Male De-esser 4 Frequency target of this de-esser is adjusted for a
man's voice.
Effect preset list
30
TASCAM DM- 4800 Effect list
Effect
Type
Preset
No.
Title Indicator Description
PITCH SHIFTER FX2.0
115 Pitch Shifter Null PitchShifterNull Basic setting for pitch shifter
116 Pitch + Whole Tone Pitch+WholeTone This pitch shifter raises vocal or other sounds by one
whole tone.
117 Pitch + 5th. Tone Pitch+5th. Tone This pitch shifter raises vocal or other sounds by a fifth
(5th).
118 Pitch – Whole Tone Pitch -WholeTone This pitch shifter lowers vocal or other sounds by one
whole tone.
119 Pitch – 5th. Tone Pitch - 5th. Tone This pitch shifter lowers vocal or other sounds by a
fifth (5th).
120 Light Chorus Light Chorus Light chorus effect
121 Doubler 1 Doubller 1 Lighter doubling (unison) effect
122 Doubler 2 Doubller 2 Deeper doubling (unison) effect
123 Octaver Octaver This pitch shifter adds a tone one octave below.
124 Organ Gliss 1 Organ Gliss 1 This pitch shifter simulates organ glissando.
125 Organ Gliss 2 Organ Gliss 2 This pitch shifter simulates organ glissando.
126 Space Invader 1 Space Invader 1 This pitch shifter creates a 70's space age type special
effect.
127 Space Invader 2 Space Invader 2 This pitch shifter creates a 70's space age type special
effect.
Notes
TASCAM DM- 4800 Effect list
31
»
DM-4800
TEAC CORPORATION
Phone: +81-422-52-5082 www.tascam.com
3-7-3, Nakacho, Musashino-shi, Tokyo 180-8550, Japan
TEAC AMERICA, INC.
Phone: +1-323-726-0303 www.tascam.com
7733 Telegraph Road, Montebello, California 90640
TEAC CANADA LTD.
Phone: +1905-890-8008 Facsimile: +1905-890-9888 www.tascam.com
5939 Wallace Street, Mississauga, Ontario L4Z 1Z8, Canada
TEAC MEXICO, S.A. De C.V
Phone: +52-555-581-5500 www.tascam.com
Campesinos No. 184, Colonia Granjes Esmeralda, Delegaacion Iztapalapa CP 09810, Mexico DF
TEAC UK LIMITED
Phone: +44-8451-302511 www.tascam.co.uk
Unit 19 & 20, The Courtyards Hatters Lane Watford, Hertfordshire. WD18 8TE, U.K.
TEAC EUROPE GmbH
Phone: +49-611-71580 www.tascam.de
Bahnstrasse 12, 65205 Wiesbaden-Erbenheim, Germany
Printed in China
Loading...